E3.1.1 Rebuild the Stage by Hand

MediumImplementngspice 42 + SKY130 · serverReview the topic

Measure one transistor at its bias and write its small-signal model. The model must match the real stage's gain and −3 dB point in three surroundings.

Circuit context: A SKY130 common-source stage (W/L = 3/0.18 µm, 0.70 V on the gate, 50 kΩ to 1.8 V) and the linear model that replaces its transistor. Write the small-signal model a hand analysis of this stage would start from.

A common-source stage uses one SKY130 NMOS with W/L = 3/0.18 µm. Its gate sits at 0.70 V and a 50 kΩ resistor joins its drain to 1.8 V.

Write the transistor's small-signal model as the subcircuit nmodel. Use one G source, resistors and capacitors. The source and body are node 0.

The grader puts your model where the transistor was and compares the two circuits. It does this in three surroundings, listed below.

A model fitted to one surrounding fails the other two. Each element must hold the value the transistor has at this bias.

What the Grader Measures

Your subcircuit nmodel (ports g, d) under the grader's own bench, one run per corner (tt):

CheckCornerRule
Gain, model ÷ stage (1 kΩ source)tt0.98 to 1.02
Gain, model ÷ stage (extra load)tt0.98 to 1.02
−3 dB point, model ÷ stage (1 kΩ source)tt0.95 to 1.05
−3 dB point, model ÷ stage (2 MΩ source)tt0.95 to 1.05
−3 dB point, model ÷ stage (2 MΩ source, extra load)tt0.95 to 1.05
Full specification
The subcircuit the grader tests (keep the name and the ports)
.subckt nmodel g d
* G sources, resistors and capacitors only; source and body are node 0
.ends
SurroundingWhat changesWhat it exposes
11 kΩ sourceThe gain and the output node's −3 dB point
22 MΩ sourceThe capacitance seen at the gate
32 MΩ source, extra 25 kΩ loadHow that capacitance changes with the gain
CheckSurroundingRuleHow the grader measures it
Gain10.98 to 1.02Model gain divided by stage gain, at 1 kHz
Gain30.98 to 1.02As above, with the extra load
−3 dB point10.95 to 1.05Model frequency divided by stage frequency
−3 dB point20.95 to 1.05As above, with the 2 MΩ source
−3 dB point30.95 to 1.05As above, with source and load

The extra load is 25 kΩ behind a large blocking capacitor. It loads the signal and leaves the bias alone.

The grader runs at the tt corner and 27 °C. The −3 dB point is where the gain falls to 1/√2 of its 1 kHz value.

Examples

Example 1

The Starter: Placeholder Values, No Capacitors
Design
.subckt nmodel g d
G1 d 0 g 0 100u
RO d 0 100k
.ends
Measured by the grader
Gain, model ÷ stage (1 kΩ source): 0.4652 (needs 0.98 to 1.02)
Gain, model ÷ stage (extra load): 0.5124 (needs 0.98 to 1.02)
−3 dB point, model ÷ stage (1 kΩ source): 1.192 (needs 0.95 to 1.05)
−3 dB point, model ÷ stage (2 MΩ source): 6.291 (needs 0.95 to 1.05)
−3 dB point, model ÷ stage (2 MΩ source, extra load): 8.811 (needs 0.95 to 1.05)

The gain is less than half of the stage's. Without capacitors the gate node has no pole at all.

Example 2

Right g_{m} and r_{o}, but No C_{gd}
Design
.subckt nmodel g d
G1 d 0 g 0 183.5u
RO d 0 181.6k
CGS g 0 3.912f
CDB d 0 1.102f
.ends
Measured by the grader
Gain, model ÷ stage (1 kΩ source): 1.004 (needs 0.98 to 1.02)
Gain, model ÷ stage (extra load): 1.005 (needs 0.98 to 1.02)
−3 dB point, model ÷ stage (1 kΩ source): 1.002 (needs 0.95 to 1.05)
−3 dB point, model ÷ stage (2 MΩ source): 2.237 (needs 0.95 to 1.05)
−3 dB point, model ÷ stage (2 MΩ source, extra load): 1.552 (needs 0.95 to 1.05)

Both gains match and so does the first −3 dB point. Behind 2 MΩ the model is more than twice too fast.

Example 3

The Full Model, Read at the Stage's Bias
Design
.subckt nmodel g d
G1 d 0 g 0 183.5u
RO d 0 181.6k
CGS g 0 3.18f
CGD g d 0.737f
CDB d 0 0.366f
.ends
Measured by the grader
Gain, model ÷ stage (1 kΩ source): 1.004 (needs 0.98 to 1.02)
Gain, model ÷ stage (extra load): 1.005 (needs 0.98 to 1.02)
−3 dB point, model ÷ stage (1 kΩ source): 1.001 (needs 0.95 to 1.05)
−3 dB point, model ÷ stage (2 MΩ source): 0.9974 (needs 0.95 to 1.05)
−3 dB point, model ÷ stage (2 MΩ source, extra load): 0.9976 (needs 0.95 to 1.05)

All five ratios sit within 0.5 % of 1. The small gain error is the contact resistance inside the SKY130 device.

Constraints and Contract

  • The netlist defines .subckt nmodel g d ... .ends exactly once, with these ports in this order.
  • Inside nmodel: G sources, resistors and capacitors, with comments and .param lines. No transistor.
  • The grader supplies the source resistor, the 50 kΩ resistor, the loads and the real stage.

Hints

Hint 1

Read gm and gds from the operating point of this stage. Check where its drain sits before you copy a bench from the lesson.

Hint 2

Surrounding 2 has a slow gate node. The gate sees more than Cgs: one capacitor joins it to a node that moves the other way.

Hint 3

Cgg is everything on the gate, Cgd included. Measure Cgd on its own and subtract it before you place Cgs.

What the grader checks: The grader compares your model with the transistor stage in three surroundings at tt and 27 °C. All numbers come from ngspice 42 with the pinned SKY130 models, measured 2026-11-12. It checks small-signal gain and the first −3 dB point only. It does not check large signals, noise, or frequencies above the first pole.

Run simulates your netlist as written, with your own analyses and measurements. Submit sends it to the grader, which keeps only the subcircuit nmodel and makes 1 ngspice run. The numbers come from ngspice and the SKY130 models the site pins; they prove the measured cases, not every condition a chip meets.

See all 1 steps and the final capstone

Report a problem with this page

Your netlist SPICESaved locally
Ln 1, Col 1Tab indents · Ctrl/⌘ + Enter runs
Not run yet
Run your netlist to see its measurements and the ngspice log here.
ngspice 42 + SKY130 · server