E7.3.1 Quieter on the Same Current

HardOptimizengspice 42 + SKY130 · serverReview the topic

Cut OTA-A's input noise to 110 nV/√Hz at 1 kHz and 18.5 nV/√Hz at 1 MHz. Keep its current, and use at most 500 µm² of gate.

Circuit context: OTA-A as the first amplifier behind a sensor whose signal sits between 1 kHz and 1 MHz, on its 20 µA reference. Cut an amplifier's input noise for a sensor without spending more current.

OTA-A (lessons E5.3 and E7.3) amplifies a sensor signal that sits between 1 kHz and 1 MHz. Its input-referred noise is 412.6 nV/√Hz at 1 kHz and 31.57 nV/√Hz at 1 MHz. The sensor needs at most 110 nV/√Hz and 18.5 nV/√Hz.

The power budget is spent. The bench still feeds 20 µA into nb, and the supply current must stay at or below 40 µA. So the noise must fall by sizing alone.

The layout gives the whole OTA at most 500 µm² of gate. The area is the sum of W · L over its six transistors. OTA-A uses 52 µm².

Keep what OTA-A did. Open loop into 1 pF, the DC gain is at least 40 dB and the unity-gain frequency at least 22 MHz. The noise limits hold at two corners: tt, and sf with its fast NMOS and slow PMOS.

What the Grader Measures

Your subcircuit ota (ports inp, inn, out, vdd, nb) under the grader's own bench, one run per corner (tt, sf):

CheckCornerRule
Input noise at 1 kHztt≤ 110 nV/√Hz
Input noise at 1 MHztt≤ 18.5 nV/√Hz
Input noise at 1 kHzsf≤ 110 nV/√Hz
Input noise at 1 MHzsf≤ 18.5 nV/√Hz
DC gaintt≥ 40 dB
Unity-gain frequencytt≥ 22 MHz
Supply currenttt≤ 40 µA
Budget: Gate areatt≤ 500 µm², the lower the better
Full specification
The subcircuit the grader tests (keep the name and the ports)
.subckt ota inp inn out vdd nb
* SKY130 FETs only (sky130_fd_pr__nfet_01v8, sky130_fd_pr__pfet_01v8); 20 uA flows into nb from the bench
.ends
CheckCornerRuleHow the grader measures it
Input noise at 1 kHztt, sf≤ 110 nV/√Hzopen loop with 1 TH and 1 F, 1 pF load, inputs at 0.9 V: inoise_spectrum at 1 kHz
Input noise at 1 MHztt, sf≤ 18.5 nV/√Hzthe same noise run, at 1 MHz
DC gaintt≥ 40 dBthe ac run of the same bench, at 10 Hz
Unity-gain frequencytt≥ 22 MHzthe same ac run, where the gain crosses 0 dB
Supply currenttt≤ 40 µAop: the current out of the 1.8 V supply, the 20 µA reference included
Gate area (budget)≤ 500 µm²the sum of W · L · m over the FETs of ota, read from the netlist

The grader runs its bench twice, with .lib sky130 tt and with .lib sky130 sf, at 27 °C. It is the bench in your netlist; only the subcircuit ota changes.

Examples

Example 1

The Starter: OTA-A, 52 µm²
Design
.subckt ota inp inn out vdd nb
XMB nb nb 0 0 sky130_fd_pr__nfet_01v8 W=8 L=1
XM5 tail nb 0 0 sky130_fd_pr__nfet_01v8 W=8 L=1
XM1 x inp tail 0 sky130_fd_pr__nfet_01v8 W=10 L=1
XM2 out inn tail 0 sky130_fd_pr__nfet_01v8 W=10 L=1
XM3 x x vdd vdd sky130_fd_pr__pfet_01v8 W=8 L=1
XM4 out x vdd vdd sky130_fd_pr__pfet_01v8 W=8 L=1
.ends
Measured by the grader
Input noise at 1 kHz: 412.6 nV/√Hz (needs ≤ 110 nV/√Hz)
Input noise at 1 MHz: 31.57 nV/√Hz (needs ≤ 18.5 nV/√Hz)
DC gain: 42.71 dB (needs ≥ 40 dB)
Unity-gain frequency: 25.57 MHz (needs ≥ 22 MHz)
Supply current: 38.67 µA (needs ≤ 40 µA)
Gate area: 52 µm² (budget ≤ 500 µm²)

Small and fast, with almost four times the noise allowed at 1 kHz.

Example 2

Lesson E7.3's Last Sizing: Pair 20/2, Load 8/2
Design
.subckt ota inp inn out vdd nb
XMB nb nb 0 0 sky130_fd_pr__nfet_01v8 W=8 L=1
XM5 tail nb 0 0 sky130_fd_pr__nfet_01v8 W=8 L=1
XM1 x inp tail 0 sky130_fd_pr__nfet_01v8 W=20 L=2
XM2 out inn tail 0 sky130_fd_pr__nfet_01v8 W=20 L=2
XM3 x x vdd vdd sky130_fd_pr__pfet_01v8 W=8 L=2
XM4 out x vdd vdd sky130_fd_pr__pfet_01v8 W=8 L=2
.ends
Measured by the grader
Input noise at 1 kHz: 209.6 nV/√Hz (needs ≤ 110 nV/√Hz)
Input noise at 1 MHz: 24.25 nV/√Hz (needs ≤ 18.5 nV/√Hz)
Gate area: 128 µm² (budget ≤ 500 µm²)

Four times the pair area halves the noise at 1 kHz. Both limits are still far away, and the floor has barely moved.

Example 3

Pair 60/2, Load 6/3, MB and M5 at 4/1
Design
.subckt ota inp inn out vdd nb
XMB nb nb 0 0 sky130_fd_pr__nfet_01v8 W=4 L=1
XM5 tail nb 0 0 sky130_fd_pr__nfet_01v8 W=4 L=1
XM1 x inp tail 0 sky130_fd_pr__nfet_01v8 W=60 L=2
XM2 out inn tail 0 sky130_fd_pr__nfet_01v8 W=60 L=2
XM3 x x vdd vdd sky130_fd_pr__pfet_01v8 W=6 L=3
XM4 out x vdd vdd sky130_fd_pr__pfet_01v8 W=6 L=3
.ends
Measured by the grader
Input noise at 1 kHz: 129 nV/√Hz (needs ≤ 110 nV/√Hz)
Input noise at 1 kHz at sf: 222.5 nV/√Hz (needs ≤ 110 nV/√Hz)
Input noise at 1 MHz: 18.91 nV/√Hz (needs ≤ 18.5 nV/√Hz)
Input noise at 1 MHz at sf: 23.11 nV/√Hz (needs ≤ 18.5 nV/√Hz)
Gate area: 284 µm² (budget ≤ 500 µm²)

Closer at tt. At sf the slow PMOS load needs more |V_GS|, and the fast pair leaves less room. The pair leaves saturation and the noise jumps.

Example 4

Pair 140/2, Load 16/3, MB and M5 at 4/1
Design
.subckt ota inp inn out vdd nb
XMB nb nb 0 0 sky130_fd_pr__nfet_01v8 W=4 L=1
XM5 tail nb 0 0 sky130_fd_pr__nfet_01v8 W=4 L=1
XM1 x inp tail 0 sky130_fd_pr__nfet_01v8 W=140 L=2
XM2 out inn tail 0 sky130_fd_pr__nfet_01v8 W=140 L=2
XM3 x x vdd vdd sky130_fd_pr__pfet_01v8 W=16 L=3
XM4 out x vdd vdd sky130_fd_pr__pfet_01v8 W=16 L=3
.ends
Measured by the grader
Input noise at 1 kHz: 89.59 nV/√Hz (needs ≤ 110 nV/√Hz)
Input noise at 1 kHz at sf: 89.39 nV/√Hz (needs ≤ 110 nV/√Hz)
Input noise at 1 MHz: 17.21 nV/√Hz (needs ≤ 18.5 nV/√Hz)
Input noise at 1 MHz at sf: 17.11 nV/√Hz (needs ≤ 18.5 nV/√Hz)
Unity-gain frequency: 25.99 MHz (needs ≥ 22 MHz)
Gate area: 664 µm² (budget ≤ 500 µm²)

Every limit is met with room to spare, at 664 µm²: 164 µm² over the budget.

Constraints and Contract

  • The netlist defines .subckt ota inp inn out vdd nb ... .ends exactly once, with these ports in this order.
  • Inside ota: X instances of sky130_fd_pr__nfet_01v8 and sky130_fd_pr__pfet_01v8 with W= and L= given as numbers or .param values, comments and .param lines. No sources: the 20 µA reference comes in through nb.
  • A line may carry m= for parallel copies, and the area counts them. mult= is refused: it does not change the device.
  • The grader writes the .lib line for each corner itself; everything outside ota is replaced by its bench.

Hints

Hint 1

Split the noise first, as lesson E7.3 did with noise ... 1. Do it again after each change: the largest row moves.

Hint 2

The noise power at 1 MHz follows 1/gm1. At a fixed current, g_m grows with W/L, but only until the device reaches weak inversion.

Hint 3

Flicker noise falls with gate area, whatever the W/L. That holds for the load too, and its share also scales with (gm3/gm1)2.

Hint 4

A long, narrow load needs a large |V_GS|, which pulls node x down onto the input pair. Run the sf corner before you trust a long load.

Hint 5

The noise of MB and M5 is common mode. Their area still counts, and their ratio sets the tail current.

What the grader checks: The grader places ota in lesson E7.3's open-loop bench: 1 pF, inputs at 0.9 V, 20 µA into nb. It reads the input-referred noise density at 1 kHz and 1 MHz, at tt and sf. It reads the gain, f_u and supply current at tt. Engine: ngspice 42 (libngspice0 42+ds-3build1) with the pinned SKY130 models, measured 2026-11-12 with tools/spice-judge.mjs. The area is the sum of W · L · m in the netlist. The noise is the SKY130 model's (BSIM4), not a silicon measurement. It does not check the offset, the input range, slewing or other temperatures.

Run simulates your netlist as written, with your own analyses and measurements. Submit sends it to the grader, which keeps only the subcircuit ota and makes 2 ngspice runs. The numbers come from ngspice and the SKY130 models the site pins; they prove the measured cases, not every condition a chip meets.

See all 1 steps and the final capstone

Report a problem with this page

Your netlist SPICESaved locally
Ln 1, Col 1Tab indents · Ctrl/⌘ + Enter runs
Not run yet
Run your netlist to see its measurements and the ngspice log here.
ngspice 42 + SKY130 · server