T1.5.1 Elmore by Hand, Checked by the Tool

MediumImplement25 minOpenROAD · serverReview the topic

Compute a driver's load and two met2 wire delays by hand, then let OpenSTA check them.

Hardware context: Buffer driving a long met1 wire to a second buffer. Estimate a driver load and two wire delays by hand and check them against OpenSTA.

The block lwire has a buf_2 named drv that drives a long net w to a buf_1 named rcv. Two hand-made SPEF files route that net on met2, as 700 µm or 1 mm of wire. Each is a 10-segment RC ladder, with half a segment's capacitance at each end.

Work by hand from the data in the full specification. Give the total capacitance drv drives with the 1 mm wire. Then give the Elmore delay from drv/X to rcv/A for both lengths. The server runs OpenSTA on both SPEFs and compares your numbers with its report.

Requirements

RequirementLimitUnit
Load error on drv with the 1 mm wire≤ 0.5fF
Wire delay error, 700 µm≤ 0.005ns
Wire delay error, 1 mm≤ 0.005ns

Live analysis: Live OpenSTA at tt_025C_1v80 on lwire with the authored met2 SPEFs lwire-m2-700 and lwire-m2-1000, ideal 2 ns clock. Graded: the load of drv/X with the 1 mm SPEF, within 0.5 fF. Also graded: the net line from drv/X to rcv/A on the worst setup path, within 5 ps. The tool's calculator is not plain Elmore, and the 5 ps tolerance covers the difference at these lengths.

Full specification
QuantityValue
met2 resistance (platform setRC.tcl)1.22132 Ω per µm
met2 capacitance (platform setRC.tcl)0.136233 fF per µm
Ladder10 equal segments; each inner node holds one segment's capacitance, each end half of one
rcv/A (buf_1) rise_capacitance2.191 fF (the worst path rises at rcv/A)
Clockcreate_clock -name clk -period 2.0 [get_ports clk]; set_clock_transition 0.1 [all_clocks]
JSON fieldAllowed valuesMeaning
load_ff0 to 1000Total capacitance on net w that drv drives, in fF.
delay_7000 to 1Elmore delay from drv/X to rcv/A with the 700 µm wire, in ns.
delay_10000 to 1Elmore delay from drv/X to rcv/A with the 1 mm wire, in ns.

Live OpenSTA at tt_025C_1v80 on lwire with the authored met2 SPEFs lwire-m2-700 and lwire-m2-1000, ideal 2 ns clock. Graded: the load of drv/X with the 1 mm SPEF, within 0.5 fF. Also graded: the net line from drv/X to rcv/A on the worst setup path, within 5 ps. The tool's calculator is not plain Elmore, and the 5 ps tolerance covers the difference at these lengths.

Numeric checks use inclusive bounds. A missing measurement always fails. Only the documented fields are accepted.

Examples

Example 1

Total R Times Total C
Input
Multiply the whole wire resistance by the whole capacitance
Output
Load error on drv with the 1 mm wire: PASS
Wire delay error, 700 µm: FAIL
Wire delay error, 1 mm: FAIL

The first resistor charges almost everything, but the last one charges only the far end. On average each resistor sees about half the wire.

Example 2

The Pin Left Out
Input
Use only the wire capacitance
Output
Load error on drv with the 1 mm wire: FAIL
Wire delay error, 700 µm: PASS
Wire delay error, 1 mm: PASS

The delays land close, but the driver also charges the receiver pin. The report's load includes it.

Example 3

One Lumped RC
Input
Use 0.69 times the wire's R times C
Output
Load error on drv with the 1 mm wire: PASS
Wire delay error, 700 µm: FAIL
Wire delay error, 1 mm: FAIL

0.69·RC is the 50 % point of a single resistor and capacitor under a step. A distributed wire is not one RC.

Submission Rules

  • Submit one JSON object with every documented configuration field. The supplied circuit and external environment stay fixed.
  • Run measures your configuration. Submit applies the same requirements and records the result.
  • The stated stage and cell corner define this exercise; passing does not establish full chip sign-off.

Hints

Hint 1

Write the Elmore sum: each resistor times all the capacitance beyond it, including the receiver pin.

Hint 2

For a uniform ladder with half a segment at each end, the sum closes to R·(C/2 + Cpin). R and C are for the whole wire.

Hint 3

Watch the units: kΩ times pF gives ns.

What is checked: Live OpenSTA at tt_025C_1v80 on lwire with the authored met2 SPEFs lwire-m2-700 and lwire-m2-1000, ideal 2 ns clock. Graded: the load of drv/X with the 1 mm SPEF, within 0.5 fF. Also graded: the net line from drv/X to rcv/A on the worst setup path, within 5 ps. The tool's calculator is not plain Elmore, and the 5 ps tolerance covers the difference at these lengths.

Run and Submit use the same measured requirements. Run is a preview; Submit records an attempt. The fixed circuit and allowed settings use the pinned OpenROAD/OpenSTA engine.

More problems on this topic

Report a problem with this page

Your configuration JSONSaved locally
Ln 1, Col 1Ctrl/⌘ + Enter runs
Not run yet

Run your configuration to inspect the result.

OpenROAD · server