Frequency Response of the Follower, the Common Gate and the Cascode

Measure why a follower can ring, which stages escape the Miller effect, and where the cascode hides a second pole.

You Will Be Able To

  • Explain why a follower's output impedance rises with frequency when its source resistance is high.
  • Measure the overshoot of a follower that drives a capacitor.
  • Find the input capacitance of a stage from the gain across each of its capacitors.
  • Choose the width of a cascode device from its internal pole.
Lesson
E9.6
Time
35 min
Runs on
ngspice
Check
5 questions

A source follower buffered a 1.2 V reference that had 100 kΩ of output resistance. On a 10 mV step into 1 pF the output overshot by 14.1 % and rang.

TransientOne Follower, Two Source ResistancesA 10 mV input step at 10 ns. Each follower drives 1 pF.
  • from 1 kΩ
  • from 100 kΩ
392 mV394 mV396 mV398 mV400 mV402 mV404 mVOutput050 ns100 ns150 ns200 ns250 ns300 ns350 ns400 nsTimesteppeak, 14.1 % over392 mV394 mV396 mV398 mV400 mV402 mV404 mVOutput0100 ns200 ns300 ns400 nsTimesteppeak, 14.1 % over
  1. Time 20 nsfrom 1 kΩ = 401.1 mV · from 100 kΩ = 398.7 mV

    From 1 kΩ the output rises smoothly and never passes its final value.

  2. Time 33.92 nsfrom 1 kΩ = 401.7 mV · from 100 kΩ = 402.9 mV

    From 100 kΩ the output peaks 1.17 mV above its final value. The step is 8.33 mV, so that is 14.1 %.

  3. Time 100 nsfrom 1 kΩ = 401.7 mV · from 100 kΩ = 401.7 mV

    The ringing has a period of 48.4 ns, about 20.7 MHz, and then dies away.

Read the plot as a table
Timefrom 1 kΩfrom 100 kΩ
0 s393.4 mV393.4 mV
20 ns401.1 mV398.7 mV
33.92 ns401.7 mV402.9 mV
50 ns401.7 mV401.8 mV
100 ns401.7 mV401.7 mV
150 ns401.7 mV401.7 mV
200 ns401.7 mV401.7 mV
250 ns401.7 mV401.7 mV
300 ns401.7 mV401.7 mV
350 ns401.7 mV401.7 mV
400 ns401.7 mV401.7 mV

Run 3 of the lab. The transistor and the load are the same in both followers.

The same follower driven from 1 kΩ did not overshoot at all. The source resistance changed what the follower's output looks like.

The Follower Output Looks Like an Inductor

A Follower with Its Gate-Source Capacitance DrawnCgs is inside M1. It ties the gate to the output.
A follower with its gate-source capacitance drawn+VIN1.2 VRS​Cgs​96.5 fFM1W/L = 10/2VDDIB​20 µACL​1 pFoutgout0.393 V
  1. VIN · voltage source1.2 V+ → n1 · − → 0
  2. R_S · resistorpin 1 → g · pin 2 → n1
  3. C_gs · capacitor96.5 fFpin 1 → g · pin 2 → out
  4. M1 · NMOS transistorW/L = 10/2gate → g · drain → VDD · source → out
  5. VDD · supplyvdd → VDD
  6. I_B · current source20 µA+ → out · − → 0
  7. C_L · capacitor1 pFpin 1 → out · pin 2 → 0
  8. out · portterminal → out
  9. g1 · groundgnd → 0
  10. g2 · groundgnd → 0
  11. g3 · groundgnd → 0
  1. Low frequency

    Cgs passes no current, so the gate stays still. Push the output up and M1 cuts its current: 3.75 kΩ.

  2. High frequency, R_S = 1 kΩ

    Cgs now conducts, but 1 kΩ still holds the gate. M1 answers as before.

  3. High frequency, R_S = 100 kΩ

    Cgs drags the gate along with the output. Vgs barely changes, so M1 barely answers. The impedance rises.

Read the circuit as text
  • VIN voltage source (1.2 V): + → n1, − → 0
  • R_S resistor: pin 1 → g, pin 2 → n1
  • C_gs capacitor (96.5 fF): pin 1 → g, pin 2 → out
  • M1 NMOS transistor (W/L = 10/2): gate → g, drain → VDD, source → out
  • I_B current source (20 µA): + → out, − → 0
  • C_L capacitor (1 pF): pin 1 → out, pin 2 → 0
  • out port: terminal → out
  • out = 0.393 V

The lab removes CL for the impedance run and puts it back for the step.

A follower has a low output impedance because M1 fights any change at its source. It can fight only while its gate holds still.

AC analysisOutput Impedance of the FollowerA test current into the output, with the input quiet and CL removed.
  • RS = 1 kΩ
  • RS = 100 kΩ
10 Ω100 Ω1 kΩ10 kΩ100 kΩOutput impedance1 kHz10 kHz100 kHz1 MHz10 MHz100 MHz1 GHz10 GHz100 GHzFrequencyhighest, 13.2 kΩ10 Ω100 Ω1 kΩ10 kΩ100 kΩOutput impedance1 kHz1 MHz1 GHzFrequencyhighest, 13.2 kΩ
  1. Frequency 1 kHzRS = 1 kΩ = 3.752 kΩ · RS = 100 kΩ = 3.752 kΩ

    At low frequency both read 3.75 kΩ. The formula 1/(gm + gmb + gds) gives 3.745 kΩ.

  2. Frequency 10 MHzRS = 1 kΩ = 3.751 kΩ · RS = 100 kΩ = 4.506 kΩ

    At 10 MHz the 100 kΩ curve is rising, and its phase is +23.6°. Voltage leads current, as in an inductor.

  3. Frequency 100 MHzRS = 1 kΩ = 3.707 kΩ · RS = 100 kΩ = 12.69 kΩ

    At 100 MHz the 100 kΩ follower shows 12.7 kΩ. The 1 kΩ follower still shows 3.71 kΩ.

Read the plot as a table
FrequencyRS = 1 kΩRS = 100 kΩ
1 kHz3.752 kΩ3.752 kΩ
10 kHz3.752 kΩ3.752 kΩ
100 kHz3.752 kΩ3.752 kΩ
1 MHz3.752 kΩ3.76 kΩ
10 MHz3.751 kΩ4.506 kΩ
100 MHz3.707 kΩ12.69 kΩ
1 GHz2.268 kΩ6.165 kΩ
10 GHz621.7 Ω680.3 Ω
100 GHz76.33 Ω77.45 Ω

Run 2 of the lab. The test current is 1 A (AC), so volts read as ohms.

An impedance that rises with frequency is inductive. The follower contains no coil. RS and Cgs together delay the gate, and that delay acts like one.

The rise stops at 13.2 kΩ, well below RS. The body sits at ground, so gmb still answers a change at the source, whatever the gate does.

An Inductor and a Capacitor Ring

Put a capacitor on an inductive output and the two exchange energy. The gain peaks at one frequency, and a step rings near it.

AC analysisFollower Gain into 1 pFThe same follower from 1 kΩ and from 100 kΩ.
  • from 1 kΩ
  • from 100 kΩ
-90 dB-80 dB-70 dB-60 dB-50 dB-40 dB-30 dB-20 dB-10 dB0Gain1 kHz10 kHz100 kHz1 MHz10 MHz100 MHz1 GHz10 GHzFrequencypeak, 15.8 MHz-100 dB-80 dB-60 dB-40 dB-20 dB0Gain1 kHz100 kHz10 MHz1 GHzFrequencypeak, 15.8 MHz
  1. Frequency 1 kHzfrom 1 kΩ = -1.587 dB · from 100 kΩ = -1.587 dB

    Both start at a gain of 0.833, which is −1.59 dB. The body effect keeps it below 1 (E3.5).

  2. Frequency 15.85 MHzfrom 1 kΩ = -2.209 dB · from 100 kΩ = -0.6593 dB

    From 100 kΩ the gain climbs to 0.927 at 15.8 MHz: 0.93 dB of peaking. From 1 kΩ there is none.

  3. Frequency 40.45 MHzfrom 1 kΩ = -4.6 dB · from 100 kΩ = -9.491 dB

    The 1 kΩ follower is 3 dB down at 40.5 MHz. The 100 kΩ follower got there at 30.2 MHz.

Read the plot as a table
Frequencyfrom 1 kΩfrom 100 kΩ
1 kHz-1.587 dB-1.587 dB
10 kHz-1.587 dB-1.587 dB
100 kHz-1.587 dB-1.587 dB
1 MHz-1.59 dB-1.581 dB
10 MHz-1.846 dB-1.034 dB
15.85 MHz-2.209 dB-0.6593 dB
40.45 MHz-4.6 dB-9.491 dB
100 MHz-10.04 dB-25.8 dB
1 GHz-25.6 dB-60.58 dB
10 GHz-42.1 dB-81.98 dB

Run 1 of the lab.

Peaking in the frequency response and overshoot in the step are one effect seen twice. Here 0.93 dB of peaking comes with 14.1 % of overshoot.

Four things decide the ringing together: RS, Cgs, gm and CL. Change one and check the step again.

Which Stages Escape the Miller Effect

E6.1 showed the Miller effect: a capacitor across a gain of −A looks (1 + A) times larger from the input. The rule is general. Look at the gain between the two plates of each capacitor.

Stage (20 µA, W/L = 4/0.5)GainInput capacitanceWhat the capacitors see
Common source9.70721.88 fFCgd spans the gate and the drain: × (1 + 9.71)
Cascode9.69513.43 fFM1's drain is node x, which moves only 0.89 times
Common gate10.9512.24 fFThe gate is fixed: no capacitor joins input and output
Follower0.84143.554 fFCgs sees 1 − 0.84 of the input: it shrinks

From the netlist of the next figure, at 1 MHz. Loads are 40 kΩ; the follower has a 20 µA sink.

The two gate-input stages give Cgd = 0.96 fF and 11.6 fF that is not multiplied. In the common source, 0.96 fF acts like 10.3 fF.

The common gate has no capacitor from input to output. Its 12.2 fF sits beside a 3.65 kΩ input resistance, so its input pole is at 3.56 GHz.

AC analysisCommon Source and Cascode Behind 100 kΩSame gain, same load, same source resistance.
  • common source
  • cascode (Miller-free)
-70 dB-60 dB-50 dB-40 dB-30 dB-20 dB-10 dB010 dB20 dB30 dBGain100 kHz1 MHz10 MHz100 MHz1 GHz10 GHz100 GHzFrequencycommon source −3 dBcascode −3 dB-80 dB-60 dB-40 dB-20 dB020 dB40 dBGain100 kHz10 MHz1 GHz100 GHzFrequencycommon source −3 dBcascode −3 dB
  1. Frequency 100 kHzcommon source = 19.74 dB · cascode (Miller-free) = 19.73 dB

    Both stages have a gain of 9.7, which is 19.7 dB.

  2. Frequency 71.01 MHzcommon source = 16.73 dB · cascode (Miller-free) = 18.38 dB

    The common source is 3 dB down at 71.0 MHz. Its 21.9 fF input loads the 100 kΩ source.

  3. Frequency 117.2 MHzcommon source = 14.02 dB · cascode (Miller-free) = 16.71 dB

    The cascode holds on to 117 MHz. Its input is only 13.4 fF.

Read the plot as a table
Frequencycommon sourcecascode (Miller-free)
100 kHz19.74 dB19.73 dB
1 MHz19.74 dB19.73 dB
10 MHz19.66 dB19.7 dB
71.01 MHz16.73 dB18.38 dB
100 MHz14.99 dB17.36 dB
117.2 MHz14.02 dB16.71 dB
1 GHz-3.62 dB-0.8607 dB
10 GHz-30.47 dB-37.97 dB
100 GHz-52.85 dB-63.33 dB

The cascode gives 1.65 times the bandwidth from the same devices.

The Cascode Hides a Pole at Node x

The cascode pays for its small input capacitance with an extra node. Node x has a resistance near 1/(gm2 + gmb2) and a capacitance Cx.

Its pole is near (gm2 + gmb2)/(2πCx). A wider M2 raises gm2. It also adds its own Cgs and source junction to Cx.

AC analysisImpedance of Node x for Four Cascode WidthsM1 stays 4 µm wide at 20 µA. Only M2 changes.
  • M2 2 µm
  • M2 4 µm
  • M2 16 µm
  • M2 64 µm
10 Ω100 Ω1 kΩ10 kΩImpedance1 kHz10 kHz100 kHz1 MHz10 MHz100 MHz1 GHz10 GHz100 GHzFrequency64 µm pole2 µm pole10 Ω100 Ω1 kΩ10 kΩImpedance1 kHz1 MHz1 GHzFrequency64 µm pole2 µm pole
  1. Frequency 1 MHzM2 2 µm = 4.463 kΩ · M2 4 µm = 3.285 kΩ · M2 16 µm = 2.185 kΩ · M2 64 µm = 1.825 kΩ

    A wider M2 gives a lower resistance at x: 4.46 kΩ at 2 µm, 1.82 kΩ at 64 µm.

  2. Frequency 686.6 MHzM2 2 µm = 4.408 kΩ · M2 4 µm = 3.235 kΩ · M2 16 µm = 2.062 kΩ · M2 64 µm = 1.29 kΩ

    The 64 µm node is already 3 dB down at 0.687 GHz. Its Cx is 127 fF.

  3. Frequency 4.328 GHzM2 2 µm = 3.155 kΩ · M2 4 µm = 2.191 kΩ · M2 16 µm = 902.3 Ω · M2 64 µm = 286 Ω

    The 2 µm node holds until 4.33 GHz, with only 8.24 fF.

Read the plot as a table
FrequencyM2 2 µmM2 4 µmM2 16 µmM2 64 µm
1 kHz4.463 kΩ3.285 kΩ2.185 kΩ1.825 kΩ
10 kHz4.463 kΩ3.285 kΩ2.185 kΩ1.825 kΩ
100 kHz4.463 kΩ3.285 kΩ2.185 kΩ1.825 kΩ
1 MHz4.463 kΩ3.285 kΩ2.185 kΩ1.825 kΩ
10 MHz4.463 kΩ3.285 kΩ2.185 kΩ1.824 kΩ
100 MHz4.462 kΩ3.284 kΩ2.182 kΩ1.806 kΩ
686.6 MHz4.408 kΩ3.235 kΩ2.062 kΩ1.29 kΩ
1 GHz4.348 kΩ3.181 kΩ1.946 kΩ1.033 kΩ
4.328 GHz3.155 kΩ2.191 kΩ902.3 Ω286 Ω
10 GHz1.772 kΩ1.187 kΩ420.8 Ω125.2 Ω
100 GHz194 Ω128 Ω43.62 Ω14.07 Ω

Run 2 of the lab, with each output held by a voltage source.

Width of M2Resistance at xCxPole
1 µm6.389 kΩ6.357 fF3.919 GHz
2 µm4.463 kΩ8.240 fF4.328 GHz
4 µm3.285 kΩ12.50 fF3.875 GHz
16 µm2.185 kΩ37.12 fF1.963 GHz
64 µm1.825 kΩ127.0 fF686.6 MHz

From the lab. Cx is 1/(2π · pole · resistance).

The pole has a best width, near 2 µm here. From 2 µm to 64 µm the resistance falls 2.4 times, but Cx grows 15 times.

M2 moves toward weak inversion as it widens, and there gm stops growing with width (E2.5). Its capacitance keeps growing.

Where the Capacitance of Each Stage ActsEach arrow names a capacitance and points to the node it slows.
  • Device
  • Measure
  • Analysis
Where the capacitance of each stage actsEach arrow names a capacitance and points to the node it slows. device Follower behind 100 kΩ device Common source gain 9.71 device Common gate gate fixed device Cascode input only 13.4 fF measure Gate and output peak at 15.8 MHzinto 1 pF measure Input, the gate 21.9 fF, 71.0 MHzbehind 100 kΩ measure Input, the source pole at 3.56 GHz measure Node x pole at 4.33 GHz atbest Cgs joins themCgd × (1 + 9.71)12.2 fF, 3.65 kΩCx
  1. device Followerbehind 100 kΩ
    • Cgs joins them → Gate and output
  2. measure Gate and outputpeak at 15.8 MHz into 1 pF
  3. device Common sourcegain 9.71
    • Cgd × (1 + 9.71) → Input, the gate
  4. measure Input, the gate21.9 fF, 71.0 MHz behind 100 kΩ
  5. device Common gategate fixed
    • 12.2 fF, 3.65 kΩ → Input, the source
  6. measure Input, the sourcepole at 3.56 GHz
  7. device Cascodeinput only 13.4 fF
    • Cx → Node x
  8. measure Node xpole at 4.33 GHz at best
  1. Follower

    Cgs ties the gate to the output. A high RS lets the gate move, and the output rings.

  2. Common source

    Cgd sits across the full gain. The enlarged input capacitance loads the source resistance.

  3. Common gate and cascode

    Neither multiplies a capacitor by its gain. The cascode pays with a pole at node x.

Read the diagram as text
  • Follower: behind 100 kΩ
  • Common source: gain 9.71
  • Common gate: gate fixed
  • Cascode: input only 13.4 fF
  • Gate and output: peak at 15.8 MHz into 1 pF
  • Input, the gate: 21.9 fF, 71.0 MHz behind 100 kΩ
  • Input, the source: pole at 3.56 GHz
  • Node x: pole at 4.33 GHz at best
  • Follower → Gate and output: Cgs joins them
  • Common source → Input, the gate: Cgd × (1 + 9.71)
  • Common gate → Input, the source: 12.2 fF, 3.65 kΩ
  • Cascode → Node x: Cx

Find the node first, then the resistance and the capacitance on it.

Asked in interviews
  1. Why can a source follower ring?

    Its output impedance is 1/gm only while the gate is held. With a high source resistance, Cgs lets the gate follow the output at high frequency. The impedance then rises with frequency, like an inductor. With a load capacitor that makes a resonance. Here 100 kΩ and 1 pF gave 14.1 % of overshoot.

  2. Which single stages suffer from Miller multiplication?

    Only a stage with a capacitor between its input and an inverting, high-gain output: the common source. The common gate has its gate at AC ground. The cascode keeps the drain of its input device nearly still. In a follower, Cgs sees 1 minus the gain, so it shrinks.

  3. Where is the second pole of a cascode, and how do you size the cascode device?

    At the node between the two devices, near (gm2 + gmb2)/Cx. A wider cascode device has more gm but adds its own capacitance to that node. Sweep the width: here the pole peaked at 4.33 GHz for 2 µm and fell to 0.687 GHz for 64 µm.

Try It

Run 1 drives both followers and reads the gain into 1 pF. peak_100k is the top of the peaking.

Run 2 turns the input off and removes both loads with alter. It pushes 1 A (AC) into each follower output and into node x of each cascode. Every voltage then reads as an impedance.

Run 3 puts the loads back and applies a 10 mV step. The overshoot is the peak above the final value, as a percentage of the output step.

Predict before each change. Set RSB to 10k: does the follower still ring? Set CLB to 0.2p, then to 5p. Set IBB to 5u.

SPICEngspice 42 · simulator service
Edit the netlist, then run it
Expected measurements: cgs = 9.646508e-14 gain_lf = 8.329780e-01 peak_100k = 9.269041e-01 at= 1.584893e+07 f3_1k = 4.045048e+07 f3_100k = 3.015312e+07 zout_hand = 3.745223e+03 zout_lf = 3.751582e+03 z1k_100meg = 3.706894e+03 z100k_100meg = 1.268673e+04 z100k_max = 1.319306e+04 at= 1.584893e+08 ph_10meg = 2.362964e+01 rx_1 = 6.388606e+03 fx_1 = 3.918758e+09 rx_2 = 4.462876e+03 fx_2 = 4.327899e+09 rx_4 = 3.285095e+03 fx_4 = 3.875468e+09 rx_16 = 2.184605e+03 fx_16 = 1.962754e+09 rx_64 = 1.824564e+03 fx_64 = 6.866445e+08 cx_1 = 6.357196e-15 cx_2 = 8.240019e-15 cx_4 = 1.250109e-14 cx_16 = 3.711772e-14 cx_64 = 1.270367e-13 pk_1k = 4.017341e-01 at= 2.424250e-07 end_1k = 4.017341e-01 pk_100k = 4.029060e-01 at= 3.392500e-08 end_100k = 4.017341e-01 os_1k = 0.000000e+00 os_100k = 1.406497e+01 t_ring = 4.841619e-08 targ= 7.454910e-08 trig= 2.613291e-08

Check Yourself

Predict the outputA 100 fF capacitor joins the input and the output of an ideal buffer with a gain of 0.75. Type the line meas prints for the input capacitance (format: cin = 1.234567e-14).
* a 100 fF capacitor from the input to the output of an ideal buffer with a gain of 0.75
VIN in 0 dc 0 ac 1
E1 out 0 in 0 0.75
CF in out 100f
.control
ac dec 5 100k 10meg
let c=-imag(i(VIN))/(2*pi*frequency)
meas ac cin FIND c AT=1meg
.endc
.end
ConceptRead the output-impedance plot. What does the follower driven from 100 kΩ show at 100 MHz?
ConceptWhy does the common-gate stage show no Miller multiplication?
ConceptA designer widens the cascode device from 4 µm to 64 µm to speed up node x. What does the lab say?
ConceptIn a cascode, the gain from the input gate to node x is −0.9 and Cgd of the input device is 2 fF. How much does Cgd add to the input capacitance?

Common Mistakes

Wrong Treat a source follower as a buffer that is safe behind any source.

Behind a high resistance its output turns inductive, and a load capacitor then makes it ring.

Fix Simulate a step with the real source resistance and the real load. This follower was clean from 1 kΩ and overshot 14.1 % from 100 kΩ.

Wrong Multiply every capacitor of every stage by 1 + A.

The factor depends on the gain between the two plates of that capacitor, and that gain differs from stage to stage.

Fix Find both plate voltages first. A common gate multiplies nothing, and a follower shrinks its Cgs.

Wrong Make the cascode device as wide as the layout allows, to push its pole out.

Its gm stops growing with width while its capacitance keeps growing, so the pole comes down.

Fix Sweep the width and read the pole. Here 2 µm gave 4.33 GHz and 64 µm gave 0.687 GHz.

Wrong Measure the follower's output impedance with the input source still driving.

The reading then mixes the gain of the stage into the impedance.

Fix Turn the input's AC value off and push a test current into the output.

Before
alter ITB ac=1
ac dec 40 1k 100g
After
alter VIN ac=0
alter ITB ac=1
ac dec 40 1k 100g

Remember

  • A follower's output impedance is low only while its gate is held. Behind 100 kΩ it rose from 3.75 kΩ to 13.2 kΩ.
  • A rising impedance is inductive. With a load capacitor it rings: 14.1 % overshoot into 1 pF here.
  • The Miller factor comes from the gain across each capacitor. Only the common source multiplies Cgd by its full gain.
  • The cascode's input stays small (13.4 fF against 21.9 fF), which gave 1.65 times the bandwidth behind 100 kΩ.
  • The cascode adds a pole at node x. It has a best cascode width: 2 µm here.

Practice

Report a problem with this page