Delay: The RC Model, Elmore Delay and Input Slope

Estimate the delay of a gate and of a wire as a resistance charging capacitance, and check each estimate against a measurement.

You Will Be Able To

  • Estimate a delay as 0.69 times a resistance times a capacitance.
  • Predict how the delay of a gate changes with its load, its size and its input edge.
  • Compute the Elmore delay of an RC ladder and of an RC tree.
  • State where the Elmore estimate is good and where it is poor.
Lesson
G9.6
Time
30 min
Runs on
ngspice
Check
5 questions

A gate met its timing in the block-level run with a 10 fF load: 39.2 ps. On the chip its output also drove a long wire, and the load was 40 fF. The gate now took 99.5 ps. Nothing in the gate had changed.

TransientOne Inverter, Three LoadsThe unit inverter (NMOS 1 µm, PMOS 2 µm). Its input rises in 50 ps. The output drives 10 fF, 20 fF or 40 fF.
  • v(in)
  • v(y2), 10 fF
  • v(y3), 20 fF
  • v(y4), 40 fF
-0.5 V00.5 V1.0 V1.5 V2.0 VVoltage00.2 ns0.4 ns0.6 ns0.8 ns1.0 ns1.2 nsTimehalf of the supply10 fF: 39.2 ps20 fF: 59.4 ps40 fF: 99.5 ps-0.5 V00.5 V1.0 V1.5 V2.0 VVoltage00.5 ns1.0 nsTimehalf of the supply10 fF: 39.2 ps20 fF: 59.4 ps40 fF: 99.5 ps
  1. Time 125 psv(in) = 900 mV · v(y2), 10 fF = 1.877 V · v(y3), 20 fF = 1.849 V · v(y4), 40 fF = 1.828 V

    The input crosses 0.9 V. Each delay is counted from here to the same level at the output.

  2. Time 164.2 psv(in) = 1.8 V · v(y2), 10 fF = 900.4 mV · v(y3), 20 fF = 1.309 V · v(y4), 40 fF = 1.543 V

    With 10 fF the output crosses 0.9 V after 39.2 ps.

  3. Time 184.4 psv(in) = 1.8 V · v(y2), 10 fF = 263.5 mV · v(y3), 20 fF = 900.1 mV · v(y4), 40 fF = 1.322 V

    With 20 fF it takes 59.4 ps. Ten more femtofarads cost 20.2 ps.

  4. Time 224.5 psv(in) = 1.8 V · v(y2), 10 fF = 5.719 mV · v(y3), 20 fF = 231.2 mV · v(y4), 40 fF = 900 mV

    With 40 fF it takes 99.5 ps. Twenty more cost 40.1 ps: twice as much.

Read the plot as a table
Timev(in)v(y2), 10 fFv(y3), 20 fFv(y4), 40 fF
0 s0 V1.8 V1.8 V1.8 V
125 ps900 mV1.877 V1.849 V1.828 V
164.2 ps1.8 V900.4 mV1.309 V1.543 V
184.4 ps1.8 V263.5 mV900.1 mV1.322 V
200 ps1.8 V64.3 mV603.8 mV1.155 V
224.5 ps1.8 V5.719 mV231.2 mV900 mV
400 ps1.8 V346.2 nV17.15 µV15.41 mV
600 ps1.8 V345.9 nV346.2 nV46.62 µV
800 ps0 V1.752 V1.429 V862.3 mV
1 ns0 V1.8 V1.797 V1.688 V
1.2 ns0 V1.8 V1.8 V1.792 V

Measured with ngspice 42 on SKY130, 1.8 V.

A Resistor Charging a Capacitor

A switching gate is a transistor that is on, between a supply rail and the output. The output is a capacitor. So the simplest model of delay has two parts: one resistance R and one capacitance C.

After a step, the capacitor voltage follows an exponential curve. It reaches half of its final value after 0.69 × R × C. The product RC is the time constant.

CircuitRC0.69 × RCMeasured
1 kΩ into 40 fF40 ps27.6 ps27.7 ps

The first circuit of the lab. The delay is from 50 % of the step to 50 % at the capacitor.

For one R and one C the rule is exact. A real gate is not one resistor, and a real wire is not one capacitor. The rest of the lesson finds an R and a C that still give a good answer.

Gate Delay Grows in a Straight Line with the Load

LoadOutput fallsOutput rises
none15.9 ps18.4 ps
5 fF28.9 ps34.2 ps
10 fF39.2 ps48.2 ps
20 fF59.4 ps75.7 ps
40 fF99.5 ps130.4 ps

Measured: the unit inverter, 50 ps input edge, 50 % to 50 %. Every drain and source has the junction of a contacted diffusion, 0.29 µm long, as in a laid-out cell.

From 10 fF to 40 fF the fall delay grows by 60.3 ps. In the model that is 0.69 × R × 30 fF, so R is 2.91 kΩ. This is the effective resistance of the 1 µm NMOS. The 2 µm PMOS gives 3.97 kΩ.

The delay with no load is not zero: 15.9 ps. The drains of the two transistors are capacitors as well: the junctions of their diffusions, and the overlap with their gates. This part is the diffusion capacitance, and it is always there.

Size works the other way. An inverter twice as wide has half the resistance. Into 20 fF it falls in 37.7 ps. The unit inverter into 10 fF takes 39.2 ps. Delay follows the ratio of load to size.

The RC Model of a Gate Driving a LoadWhat the measurement table says, as a circuit of four parts.
  • Device
  • Load
  • I/O
  • Power
The RC model of a gate driving a loadWhat the measurement table says, as a circuit of four parts. device Transistor thatis on effective resistanceR load Own drains diffusion capacitance io Output node crosses 50 % after0.69 RC load Load gates and wire currentchargescharges
  1. device Transistor that is oneffective resistance R
    • current → Output node
  2. io Output nodecrosses 50 % after 0.69 RC
    • charges → Own drains
    • charges → Load
  3. load Own drainsdiffusion capacitance
  4. load Loadgates and wire
  1. No load

    Only the gate's own drains must be charged. The inverter still needs 15.9 ps.

  2. With a load

    The same current now charges the load too. Each extra 10 fF adds about 20.1 ps to the fall.

  3. A wider gate

    Twice the width halves R. It also doubles the gate's own drain capacitance and its input capacitance.

Read the diagram as text
  • Transistor that is on: effective resistance R
  • Own drains: diffusion capacitance
  • Output node: crosses 50 % after 0.69 RC
  • Load: gates and wire
  • Transistor that is on → Output node: current
  • Output node → Own drains: charges
  • Output node → Load: charges

Delay ≈ 0.69 × R × (diffusion capacitance + load).

A Slow Input Edge Makes a Slow Gate

The model assumed that the transistor turns on at once. With a slow input edge it turns on gradually. For part of the edge it is only half on, and the other transistor is still fighting it.

TransientThe Same Inverter and Load, Two Input EdgesThe unit inverter into 10 fF. One input rises in 50 ps, the other in 400 ps.
  • v(in1), 50 ps edge
  • v(y1)
  • v(in4), 400 ps edge
  • v(y4)
-0.5 V00.5 V1.0 V1.5 V2.0 VVoltage00.2 ns0.4 ns0.6 ns0.8 ns1.0 ns1.2 ns1.4 ns1.6 nsTimehalf of the supply50 ps edge: 39.2 ps400 ps edge: 90.0 ps-0.5 V00.5 V1.0 V1.5 V2.0 VVoltage00.5 ns1.0 ns1.5 nsTimehalf of the supply50 ps edge: 39.2 ps400 ps edge: 90.0 ps
  1. Time 125 psv(in1), 50 ps edge = 900 mV · v(y1) = 1.877 V · v(in4), 400 ps edge = 112.5 mV · v(y4) = 1.809 V

    The fast input crosses 0.9 V.

  2. Time 164.2 psv(in1), 50 ps edge = 1.8 V · v(y1) = 900.3 mV · v(in4), 400 ps edge = 288.9 mV · v(y4) = 1.813 V

    Its output follows 39.2 ps later.

  3. Time 300 psv(in1), 50 ps edge = 1.8 V · v(y1) = 3.2 µV · v(in4), 400 ps edge = 900 mV · v(y4) = 1.769 V

    The slow input crosses 0.9 V. The output has already begun to fall, because the NMOS turned on earlier in the edge.

  4. Time 390 psv(in1), 50 ps edge = 1.8 V · v(y1) = 346.3 nV · v(in4), 400 ps edge = 1.305 V · v(y4) = 899.9 mV

    The output of the slow input crosses 0.9 V 90.0 ps after its input.

Read the plot as a table
Timev(in1), 50 ps edgev(y1)v(in4), 400 ps edgev(y4)
0 s0 V1.8 V0 V1.8 V
125 ps900 mV1.877 V112.5 mV1.809 V
164.2 ps1.8 V900.3 mV288.9 mV1.813 V
200 ps1.8 V64.27 mV450 mV1.816 V
300 ps1.8 V3.2 µV900 mV1.769 V
390 ps1.8 V346.3 nV1.305 V899.9 mV
400 ps1.8 V346.1 nV1.35 V732.1 mV
600 ps1.8 V345.9 nV1.8 V522.5 nV
800 ps9.643 mV261.4 mV1.8 V345.9 nV
1 ns0 V1.799 V1.8 V345.9 nV
1.2 ns0 V1.8 V1.35 V-5.506 mV
1.4 ns0 V1.8 V450 mV743.2 mV
1.6 ns0 V1.8 V0 V1.799 V

Measured with ngspice 42 on SKY130, 1.8 V. Only the falling outputs are marked.

Input edge (0 to 100 %)Output fallsOutput rises
10 ps30.6 ps39.3 ps
50 ps39.2 ps48.2 ps
100 ps50.4 ps60.0 ps
200 ps68.0 ps82.3 ps
400 ps90.0 ps112.8 ps

Measured: the unit inverter into 10 fF.

A slow edge at one gate comes from a heavy load on the gate before it. So a large load costs twice: once in its own gate and once in the next. Timing tools store gate delay in tables of input edge against load for this reason.

Elmore Delay: Many Resistors and Capacitors

A wire has resistance and capacitance all along its length. A series stack of transistors has a small capacitor at every inner node. One RC product is not enough for these.

The Elmore delay is a sum. Take each capacitor in turn. Multiply it by the resistance between the source and that capacitor. Count only resistors that are also on the path to your node. Add the products.

The Elmore Sum for the Far End of a LadderFour sections of 1 kΩ and 10 fF, as in the lab. Each step adds one capacitor times the resistance in front of it.
  • Source
  • Load
  • Data
The Elmore sum for the far end of a ladderFour sections of 1 kΩ and 10 fF, as in the lab. Each step adds one capacitor times the resistance in front of it. source Source ideal step load n1 10 fF behind 1 kΩ load n2 10 fF behind 2 kΩ load n3 10 fF behind 3 kΩ load n4 10 fF behind 4 kΩ 1 kΩ1 kΩ1 kΩ1 kΩ
  1. source Sourceideal step
    • 1 kΩ → n1
  2. load n110 fF behind 1 kΩ
    • 1 kΩ → n2
  3. load n210 fF behind 2 kΩ
    • 1 kΩ → n3
  4. load n310 fF behind 3 kΩ
    • 1 kΩ → n4
  5. load n410 fF behind 4 kΩ
  1. The capacitor at n1

    It is charged through 1 kΩ: 1 kΩ × 10 fF = 10 ps. Sum so far: 10 ps.

  2. The capacitor at n2

    It is charged through 2 kΩ: 20 ps. Sum so far: 30 ps.

  3. The capacitor at n3

    It is charged through 3 kΩ: 30 ps. Sum so far: 60 ps.

  4. The capacitor at n4

    It is charged through all 4 kΩ: 40 ps. The Elmore delay of n4 is 100 ps, and 0.69 × 100 ps = 69 ps. Measured: 75.3 ps.

Read the diagram as text
  • Source: ideal step
  • n1: 10 fF behind 1 kΩ
  • n2: 10 fF behind 2 kΩ
  • n3: 10 fF behind 3 kΩ
  • n4: 10 fF behind 4 kΩ
  • Source → n1: 1 kΩ
  • n1 → n2: 1 kΩ
  • n2 → n3: 1 kΩ
  • n3 → n4: 1 kΩ

Lumping everything at the end would give 4 kΩ × 40 fF = 160 ps. Spreading the capacitance along the wire makes it faster.

NodeElmore sum0.69 × ElmoreMeasured
n140 ps27.6 ps11.2 ps
n270 ps48.3 ps40.9 ps
n390 ps62.1 ps64.7 ps
n4100 ps69.0 ps75.3 ps

For n1 the sum counts all four capacitors behind the first resistor: 1 kΩ × 40 fF. For n2 it adds 1 kΩ × 30 fF, and so on.

The estimate is good at the far end: 69 ps against 75.3 ps. It is poor near the source. Node n1 crosses 50 % after 11.2 ps, far sooner than 27.6 ps. Use Elmore for the end of a path, where the delay matters.

A series stack is a short ladder. In a three-input NAND the fall takes 34.2 ps when the switching input is at the top of the stack. It takes 47.9 ps when that input is at the bottom. Then the two inner nodes of the stack must be emptied as well.

Asked in interviews
  1. What is the Elmore delay?

    An estimate of the delay of an RC tree. Take each capacitor and the path from the source to it. Multiply the capacitor by the resistance this path shares with the path to your node. The sum is the Elmore delay. Multiply by 0.69 for the 50 % point.

  2. Why does delay depend on the input slope?

    A slow edge turns the driving transistor on gradually, so it delivers less current at first. The opposing transistor also stays on for longer. Both make the output move later than with a fast edge.

  3. Why is a distributed wire faster than the same R and C lumped together?

    In a ladder, capacitance near the driver is charged through only a small part of the resistance. The Elmore sum for a uniform line is about half of the total R times the total C.

Try It

t_lumped is the single RC: 27.7 ps, which is 0.69 × 40 ps. t_n4 is the far end of the ladder: 75.3 ps.

The ladder has the same total resistance as four of the lumped resistors, and the same total capacitance as the lumped capacitor. Its far end is still much faster than 0.69 × 160 ps = 110 ps.

Work out the Elmore sum for n4 after doubling R4 to 2 kΩ: 10 + 20 + 30 + 50 = 110 ps. Then change R4 and run. Compare t_n4 with 0.69 × 110 ps.

SPICEngspice 42 · simulator service
Edit the netlist, then run it
Expected measurements: t_lumped = 2.772571e-11 targ= 1.282257e-10 trig= 1.005000e-10 t_n1 = 1.117983e-11 targ= 1.116798e-10 trig= 1.005000e-10 t_n2 = 4.093309e-11 targ= 1.414331e-10 trig= 1.005000e-10 t_n3 = 6.472133e-11 targ= 1.652213e-10 trig= 1.005000e-10 t_n4 = 7.534840e-11 targ= 1.758484e-10 trig= 1.005000e-10

Check Yourself

Predict the outputThe sections of this ladder differ. Predict the exact line: the Elmore delay of the far end in picoseconds.
module tb;
  int r1 = 1, r2 = 2, r3 = 3;   // kOhm, from the driver to the far end
  int c1 = 4, c2 = 2, c3 = 1;   // fF, at the node after each resistor
  initial $display("%0d", r1 * (c1 + c2 + c3) + r2 * (c2 + c3) + r3 * c3);
endmodule
ConceptThe load of a gate is doubled and nothing else changes. What does the RC model say about its delay?
ConceptIn an RC tree, a capacitor sits on a side branch that is not on the path to your node. Which resistance multiplies it in the Elmore sum?
ConceptThe same inverter and load are driven by a 10 ps edge and by a 400 ps edge. What did the measurement show?
ConceptFor which node of an RC ladder is the Elmore estimate closest to the measured 50 % delay?

Common Mistakes

Wrong Add up all the capacitance, multiply by all the resistance, and call it the delay.

For the ladder of the lab that gives 4 kΩ × 40 fF = 160 ps. The Elmore sum is 100 ps and the measured delay is 75.3 ps.

Fix Multiply each capacitor by the resistance between the source and that capacitor only, then add.

Wrong In a tree, add the resistance of a side branch to the path.

Charge for a side branch flows only through the shared part of the path. The branch resistor itself is not on the way to your node.

Fix For a capacitor on a side branch, use the resistance the two paths share.

Wrong Forget the capacitance of the gate's own transistors.

The unit inverter with no load at all still takes 15.9 ps to fall. Its drains are a load too.

Fix Add the diffusion capacitance at the output to the load before you multiply.

Wrong Quote a gate delay without the input edge.

After a 10 ps edge the inverter falls in 30.6 ps. After a 400 ps edge, with the same load, it takes 90.0 ps.

Fix State the input edge with every delay, or use a table of delay against edge and load.

Remember

  • Delay ≈ 0.69 × R × C: the time for a capacitor to reach half of a step.
  • Gate delay grows in a straight line with the load. The gate's own drains add a fixed part.
  • A wider gate has less resistance. Delay follows the ratio of load to size.
  • A slow input edge adds delay, so a heavy load also slows the next gate.
  • Elmore delay: each capacitor times the resistance shared with the path, summed.

Practice

Report a problem with this page