Four Ways to Close a Loop

Name a feedback loop from what it senses and what it returns, then predict which way each port resistance moves.

You Will Be Able To

  • Name the four feedback topologies from the sensed and the returned quantity.
  • Predict whether feedback raises or lowers the input and the output resistance, and by how much.
  • Choose the topology that suits a given source and load.
  • Find the topology of a loop in a schematic with two quick tests.
Lesson
E10.1
Time
30 min
Runs on
ngspice
Check
5 questions

A sensor with 1 MΩ of source resistance needed a gain of 10, and two stages had that gain on paper. With a 10 mV signal one delivered 89.2 mV and the other −0.99 mV.

DC sweepTwo gain-of-10 Stages Behind a 1 MΩ SensorThe same amplifier in both. Stage A returns its feedback in series with the input. Stage B returns it to the input node.
  • stage A output
  • stage B output
-600 mV-400 mV-200 mV0200 mV400 mV600 mVOutput voltage-40 mV-20 mV020 mV40 mVSensor voltage10 mV-600 mV-400 mV-200 mV0200 mV400 mV600 mVOutput voltage-50 mV050 mVSensor voltage10 mV
  1. Sensor voltage 10 mVstage A output = 89.2 mV · stage B output = -988 µV

    At 10 mV stage A gives 89.2 mV. Stage B gives −0.99 mV: the signal is almost gone.

  2. Sensor voltage 50 mVstage A output = 446 mV · stage B output = -4.94 mV

    Both lines are straight. Stage B is not broken. Its input simply loads the sensor.

Read the plot as a table
Sensor voltagestage A outputstage B output
-40 mV-356.8 mV3.952 mV
-20 mV-178.4 mV1.976 mV
0 V0 V0 V
10 mV89.2 mV-988 µV
20 mV178.4 mV-1.976 mV
40 mV356.8 mV-3.952 mV
50 mV446 mV-4.94 mV

The sensor sees 9.19 MΩ at the input of stage A and 10.1 kΩ at the input of stage B.

The amplifier inside has 100 kΩ between its inputs. Feedback turned that into 9.19 MΩ in one stage and 10.1 kΩ in the other.

Two Choices at Each Port

The Four Feedback TopologiesEach cell names the input connection first and the output connection second. Arrows show which choice changes.
  • Neutral
  • Structure
The four feedback topologiesEach cell names the input connection first and the output connection second. Arrows show which choice changes. neutral Series-shunt returns voltage,senses voltage neutral Series-series returns voltage,senses current neutral Shunt-shunt returns current,senses voltage neutral Shunt-series returns current,senses current sense currentsense currentreturn currentreturn current
  1. neutral Series-shuntreturns voltage, senses voltage
    • sense current → Series-series
    • return current → Shunt-shunt
  2. neutral Shunt-shuntreturns current, senses voltage
    • sense current → Shunt-series
  3. neutral Series-seriesreturns voltage, senses current
    • return current → Shunt-series
  4. neutral Shunt-seriesreturns current, senses current
  1. Series-shunt: a voltage amplifier

    It holds the output voltage still. The lab measures Rin = 10 MΩ and Rout = 10 Ω.

  2. Shunt-shunt: current in, voltage out

    It also holds the output voltage, but takes a current. Rin = 1 kΩ and Rout = 10 Ω.

  3. Series-series: voltage in, current out

    It holds the output current still. Rin = 10 MΩ and Rout = 100 kΩ.

  4. Shunt-series: a current amplifier

    It takes a current and holds the output current. Rin = 1 kΩ and Rout = 100 kΩ.

Read the diagram as text
  • Series-shunt: returns voltage, senses voltage
  • Series-series: returns voltage, senses current
  • Shunt-shunt: returns current, senses voltage
  • Shunt-series: returns current, senses current
  • Series-shunt → Series-series: sense current
  • Shunt-shunt → Shunt-series: sense current
  • Series-shunt → Shunt-shunt: return current
  • Series-series → Shunt-series: return current

The bare amplifier has Rin = 100 kΩ and Rout = 1 kΩ. Every loop here has a loop gain of 99.

A feedback loop senses a quantity at the output and returns a part of it to the input. The sensed quantity is the output voltage or the output current. The returned quantity is a voltage or a current.

To sense a voltage, the network connects across the output: a shunt connection. To sense a current, the network sits in the path of the load current: a series connection.

To return a voltage, the network sits in series with the input source, so the two voltages subtract. To return a current, it connects to the input node, so the two currents subtract.

What Each Choice Does to a Port

Series-Shunt on the Lab AmplifierThe source E_F returns 0.099 of the output voltage to the inverting input.
Series-shunt on the lab amplifier+−++−vin​A = 1000EF​0.099·v_outout
  1. v_in · voltage source+ → n1 · − → 0
  2. A = 1000 · op-amp−in → n2 · +in → n1 · out → n3
  3. E_F · voltage source0.099·v_out+ → n2 · − → 0
  4. g1 · groundgnd → 0
  5. g2 · groundgnd → 0
  6. out · portterminal → n3
  1. Sense

    E_F reads the output voltage. It connects across the output, so this is a shunt connection.

  2. Return

    E_F drives the other input. The amplifier sees vin − 0.099·vout: the voltages subtract in series.

Read the circuit as text
  • v_in voltage source: + → n1, − → 0
  • A = 1000 op-amp: −in → n2, +in → n1, out → n3
  • E_F voltage source (0.099·v_out): + → n2, − → 0
  • out port: terminal → n3

An ideal controlled source stands for the feedback network, so the network adds no load.

Take the series input first. The loop makes the returned voltage follow vin. Only a small difference is left across the 100 kΩ. Little current flows, so the source sees a high resistance.

At a shunt input the loop removes most of the input current. The input node barely moves, so the source sees a low resistance.

At the output, a loop that senses voltage fights any change of that voltage. The output looks like a voltage source: low resistance. A loop that senses current fights any change of the current. The output looks like a current source: high resistance.

TopologyRinRoutClosed-loop gain
Bare amplifier100 kΩ1 kΩ1000 V/V
Series-shunt10.00 MΩ10.00 Ω10.00 V/V
Shunt-shunt1.000 kΩ10.00 Ω1.000 MΩ (V/A)
Series-series10.00 MΩ100.0 kΩ10.00 mA/V
Shunt-series1.000 kΩ100.0 kΩ1000 A/A

Each resistance is the bare value times or divided by 1 + T = 100.

The loop gain T is the gain once around the loop. Here T = 99 in all four. Series raises a port resistance by 1 + T. Shunt lowers it by 1 + T.

The lab shows this with a 1 kΩ load. The series-shunt loop keeps its voltage gain at 9.90 of 10. The series-series loop keeps its current at 9.90 mA/V of 10 mA/V. Without feedback, a 1 kΩ load on a 1 kΩ output halves the voltage.

Find the Topology in a Schematic

Shunt-Series on the Lab AmplifierThe source F_F returns 0.00099 of the load current to the input node.
Shunt-series on the lab amplifier−++iin​FF​0.00099·i_outA = 1000load0 V ammeter
  1. i_in · current source+ → 0 · − → n1
  2. F_F · current source0.00099·i_out+ → n1 · − → 0
  3. A = 1000 · op-amp−in → n1 · +in → 0 · out → n2
  4. load · voltage source0 V ammeter+ → n2 · − → 0
  5. g1 · groundgnd → 0
  6. g2 · groundgnd → 0
  7. g3 · groundgnd → 0
  8. g4 · groundgnd → 0
  1. Sense

    The load current flows through the ammeter. F_F copies a part of it. Open the load and the feedback is gone: a series connection.

    iout

  2. Return

    F_F takes its current from the input node, where iin arrives. The currents subtract at one node: a shunt connection.

    0.00099·iout

Read the circuit as text
  • i_in current source: + → 0, − → n1
  • F_F current source (0.00099·i_out): + → n1, − → 0
  • A = 1000 op-amp: −in → n1, +in → 0, out → n2
  • load voltage source (0 V ammeter): + → n2, − → 0

The other two topologies swap one port each: series input with series output, or shunt input with shunt output.

Two tests name any loop. First the output: short the output node to ground. If the feedback signal disappears, the loop senses voltage. If it disappears when you open the load instead, the loop senses current.

Then the input: does the feedback arrive at the same node as the input signal? Then it is shunt, and the signals add as currents. Does it arrive at a different terminal? Then it is series.

One transistor already gave you two of the four. The lab measures an NMOS, W/L = 4/0.5 µm at 20 µA.

CircuitLoopMeasuredAgainst the bare device
Source at AC ground, looking into the drainnone349.1 kΩ—
10 kΩ in the source, looking into the drainseries-series1.395 MΩ4.00 times higher
Source follower, looking into the sourceseries-shunt3.338 kΩ105 times lower

Lessons E3.4 and E3.5 derived these two stages without the word feedback.

The source resistor senses the drain current and returns a voltage at the source, in series with vGS. The follower senses its own output voltage and returns all of it. Their loop gains differ from the lab's 99. The source resistor gives T near 3 and the follower T near 104.

Asked in interviews
  1. Name the four feedback topologies and what each does to Rin and Rout.

    Series-shunt raises Rin and lowers Rout. Shunt-shunt lowers both. Series-series raises both. Shunt-series lowers Rin and raises Rout. Each change is a factor of about 1 + T.

  2. How do you tell voltage sensing from current sensing in a schematic?

    Short the output node to ground. If the feedback disappears, the loop senses voltage. If it disappears when the load is opened instead, the loop senses current.

  3. A sensor has 1 MΩ of source resistance. Which input connection do you choose?

    Series. It raises the input resistance by 1 + T, so the sensor is not loaded. In the hook the series stage shows 9.19 MΩ and the shunt stage 10.1 kΩ.

Try It

Each feedback network is one controlled source. E returns a voltage from a voltage and G a current from a voltage. H returns a voltage from a current and F a current from a current. F and H read the current of a 0 V source, which also stands for a shorted load.

Run 1 drives each input with AC 1 and reads the input resistance and the gain. A voltage source of 1 V gives Rin = 1/|i|. A current source of 1 A gives Rin = |v|.

Run 2 silences the inputs with alter and tests each output. A shunt output takes a 1 A test current. A series output takes a 1 V test source inside the load path.

Predict before each change. Halve the gain of EA to 500: which eight numbers change, and to what? Then make EFA 0.999: what happens to gain_a and rout_a?

SPICEngspice 42 · simulator service
Edit the netlist, then run it
Expected measurements: rin_a = 1.000000e+07 gain_a = 1.000000e+01 rin_b = 1.000000e+03 gain_b = 1.000000e+06 rin_c = 1.000000e+07 gain_c = 1.000000e-02 rin_d = 1.000000e+03 gain_d = 1.000000e+03 gain_a_load = 9.900990e+00 gain_c_load = 9.900990e-03 rout_a = 1.000000e+01 rout_b = 1.000000e+01 rout_c = 1.000000e+05 rout_d = 1.000000e+05 ro_bare = 3.491105e+05 ro_degen = 1.394843e+06 ro_follower = 3.338424e+03

Check Yourself

Predict the outputThis is the lab's shunt-shunt loop with twice the feedback: 1.98 µS in place of 0.99 µS. Type the line meas prints for the input resistance (format: rin_b = 1.234567e+03).
* the lab's shunt-shunt loop with twice the feedback: 1.98 uS in place of 0.99 uS
.subckt oa inp inn out
RI inp inn 100k
EA x 0 inp inn 1000
RO x out 1k
.ends
IB 0 inb DC 0 AC 1
XB 0 inb outb oa
GFB inb 0 outb 0 -1.98u
.control
ac dec 5 100 10k
meas ac rin_b FIND vm(inb) AT=1k
.endc
.end
ConceptRead the hook plot. The two stages have gains of +10 and −10 on paper. At a sensor voltage of 10 mV, about how many times larger is the output of stage A?
ConceptAn amplifier must take the current of a photodiode and drive a long cable with a voltage. Which topology suits both ports?
ConceptIn the lab, the series-series loop has Rout = 100 kΩ. Its feedback source is changed from 99 Ω to 9 Ω. What is Rout now?
ConceptYou short the output node of a feedback amplifier to ground, and the feedback signal at the input stays. What does the loop sense?

Common Mistakes

Wrong Say that negative feedback always raises the input resistance and lowers the output resistance.

That is true only for series-shunt; the lab's shunt inputs fall to 1 kΩ and its series outputs rise to 100 kΩ.

Fix Decide each port on its own: series raises the resistance by 1 + T, and shunt lowers it by 1 + T.

Wrong Put an inverting op-amp stage behind a source with a high resistance.

The inverting stage has a shunt input, so the hook's 1 MΩ sensor sees 10.1 kΩ and loses 99 % of its signal.

Fix Use the non-inverting stage, whose series input shows 9.19 MΩ in the hook.

Wrong Name the topology from the amplifier inside the loop.

The same amplifier makes all four in the lab; only the two connections of the network differ.

Fix Look at the network: across the output or in series with the load, and to the input node or to another terminal.

Remember

  • A loop senses the output voltage (shunt) or the output current (series), and returns a voltage (series) or a current (shunt).
  • A series connection raises that port's resistance by 1 + T. A shunt connection lowers it by 1 + T.
  • The loop holds still the quantity it senses: voltage sensing makes a voltage source, current sensing a current source.
  • Short the output to see what is sensed. Check which node the feedback reaches to see what is returned.
  • A source resistor is a series-series loop and a source follower is a series-shunt loop.

Practice

Report a problem with this page