The Series-Shunt Amplifier with Loading

Open a two-transistor feedback loop with its loading kept, and account for every step from the resistor ratio to the measured gain.

You Will Be Able To

  • Find what a feedback network loads at the input and at the output of a series-shunt loop.
  • Predict the closed-loop gain from the loaded open-loop gain and the feedback factor.
  • Write a gain error budget and say which term is largest.
  • Explain why a grounded body changes the gain that the resistor ratio promises.
Lesson
E10.2
Time
35 min
Runs on
ngspice
Check
5 questions

A two-transistor amplifier was built for a gain of 10, with RF = 18 kΩ and R1 = 2 kΩ. The run measures 7.47. Nothing is broken: three separate effects took the missing 25 %.

AC analysisA Gain of 10 on PaperThe closed-loop gain of the feedback pair against frequency, as a ratio.
0246810Gain1 kHz10 kHz100 kHz1 MHz10 MHz100 MHz1 GHz10 GHzFrequencyresistor ratio: 100246810Gain1 kHz100 kHz10 MHz1 GHzFrequencyresistor ratio: 10
  1. Frequency 10 kHzclosed-loop gain = 7.468

    The gain is flat at 7.47. The resistor ratio promised 10.

Read the plot as a table
Frequencyclosed-loop gain
1 kHz7.468
10 kHz7.468
100 kHz7.468
1 MHz7.468
10 MHz7.468
100 MHz7.388
1 GHz3.673
10 GHz0.2704

No load capacitor is attached, so the gain stays flat far beyond any real use.

This lesson finds each effect and gives it a number.

The Pair and Its Network

A Series-Shunt Feedback PairM1 and M2 amplify. RF and R1 sense the output voltage and return a part of it to the source of M1.
A series-shunt feedback pair+VDD1.8 VVDDRD​60 kΩM14/0.5M220/0.5RF​18 kΩR1​2 kΩvin​0.95 V DCouts10.162 Vd10.618 Vout1.264 V
  1. VDD · supply1.8 Vvdd → VDD
  2. VDD · supplyvdd → VDD
  3. R_D · resistor60 kΩpin 1 → VDD · pin 2 → d1
  4. M1 · NMOS transistor4/0.5gate → n1 · drain → d1 · source → s1
  5. M2 · PMOS transistor20/0.5gate → d1 · source → VDD · drain → out
  6. R_F · resistor18 kΩpin 1 → out · pin 2 → s1
  7. R_1 · resistor2 kΩpin 1 → s1 · pin 2 → 0
  8. v_in · voltage source0.95 V DC+ → n1 · − → 0
  9. g1 · groundgnd → 0
  10. g2 · groundgnd → 0
  11. out · portterminal → out
  1. Two gain stages

    M1 carries 19.7 µA and M2 carries 61.2 µA. Each stage inverts, so the output moves the same way as the input.

    19.7 µA

  2. Sense and return

    RF and R1 divide the output voltage and place a part of it on the source of M1. The input drives the gate. M1 amplifies the difference: a series-shunt loop.

  3. Loading at the input

    Hold the output still. The source of M1 then sees R1 in parallel with RF: 1.8 kΩ of degeneration.

  4. Loading at the output

    Disconnect the source of M1. The drain of M2 then sees RF in series with R1: a 20 kΩ load.

  5. The ideal feedback factor

    What is left is a divider that loads nothing: β = R1/(R1 + RF) = 0.1.

Read the circuit as text
  • R_D resistor (60 kΩ): pin 1 → VDD, pin 2 → d1
  • M1 NMOS transistor (4/0.5): gate → n1, drain → d1, source → s1
  • M2 PMOS transistor (20/0.5): gate → d1, source → VDD, drain → out
  • R_F resistor (18 kΩ): pin 1 → out, pin 2 → s1
  • R_1 resistor (2 kΩ): pin 1 → s1, pin 2 → 0
  • v_in voltage source (0.95 V DC): + → n1, − → 0
  • out port: terminal → out
  • s1 = 0.162 V
  • d1 = 0.618 V
  • out = 1.264 V

The body of M1 is at ground. That matters later in this lesson.

The ideal rule says the closed-loop gain is 1/β = 10. It assumes a very large loop gain and a network that loads nothing. Neither holds here.

A real network is made of resistors, and they carry current. At the input they sit in the source of M1 and lower its gain. At the output they load M2.

Open the Loop, Keep the Loading

To find the loop gain, we need the gain of the amplifier with the network's load on it but without its feedback. For a series-shunt loop there are two rules.

PortWhat you do to the other portWhat the amplifier seesHere
Input (series)Short the output nodeR1 ∥ RF in the source of M11.8 kΩ
Output (shunt)Open the input connectionRF + R1 from the drain of M2 to ground20 kΩ

Short a port that the network senses as a voltage. Open a port where it returns a voltage in series.

The lab builds this opened loop as a second copy of the two transistors. A voltage source holds the far end of RF at the DC output level. A current source replaces the DC current of M1 in R1. The copy then sits at the same operating point: both outputs are at 1.264 V.

With the loading in place, hand analysis gives each stage. A1 = gm1RD/(1 + (gm1 + gmb1)·1.8 kΩ) and A2 = gm2·(ro2 ∥ 20 kΩ).

QuantityBy hand, from the operating pointFrom the AC run
First stage A19.678—
Second stage A29.305—
Open-loop gain A90.0578.99
Output resistance, loop openro2 ∥ 20 kΩ17.38 kΩ

The hand value of A is 14 % high. It leaves out ro of M1, which lets the drain of M1 react to its source.

The Gain Error Budget

Now close the loop on paper. The closed-loop gain is A/(1 + A·β). One more effect enters first, and it is specific to this circuit.

The returned voltage arrives at the source of M1. The body of M1 is at ground, so a rising source also lowers VBS. The feedback therefore acts through gm1 + gmb1, while the input acts through gm1 alone. The effective feedback factor β′ is β·(gm1 + gmb1)/gm1 = 0.120, not 0.100.

StepClosed-loop gainLost at this step
Resistor ratio, 1/β10—
Body of M1 at ground, 1/β′8.3416.6 %
Finite loop gain, measured A = 79.07.5409.5 %
The run7.4680.9 %

Each loss is a share of the gain left by the step before. The last 0.9 % is what the two-port picture leaves out, such as signal that passes forward through the network.

Where the Gain GoesThe top row is the gain after each step. The bottom row is the cause.
  • Neutral
  • Measure
  • Analysis
Where the gain goesThe top row is the gain after each step. The bottom row is the cause. neutral Resistor ratio gain 10 neutral Body at ground gain 8.34 neutral Finite loop gain gain 7.54 measure The run gain 7.47 neutral Feedback factor 0.120, not 0.100 measure Loop gain T = 9.48 neutral Forward signal passes through thenetwork 16.6 % lost9.5 % lost0.9 % lost
  1. neutral Resistor ratiogain 10
    • 16.6 % lost → Body at ground
  2. neutral Body at groundgain 8.34
    • 9.5 % lost → Finite loop gain
  3. neutral Feedback factor0.120, not 0.100
    • Body at ground
  4. neutral Finite loop gaingain 7.54
    • 0.9 % lost → The run
  5. measure Loop gainT = 9.48
    • Finite loop gain
  6. measure The rungain 7.47
  7. neutral Forward signalpasses through the network
    • The run
  1. The body effect

    The feedback acts through gm1 + gmb1. More loop gain cannot recover this step.

  2. The loop gain

    The network loads both stages, so A is only 79.0. This step shrinks with more loop gain.

  3. The remainder

    The two-port picture leaves out the last 0.9 %.

Read the diagram as text
  • Resistor ratio: gain 10
  • Body at ground: gain 8.34
  • Finite loop gain: gain 7.54
  • The run: gain 7.47
  • Feedback factor: 0.120, not 0.100
  • Loop gain: T = 9.48
  • Forward signal: passes through the network
  • Resistor ratio → Body at ground: 16.6 % lost
  • Body at ground → Finite loop gain: 9.5 % lost
  • Finite loop gain → The run: 0.9 % lost
  • Feedback factor → Body at ground
  • Loop gain → Finite loop gain
  • Forward signal → The run

Three effects take the missing 25 %.

The loop gain is T = A·β′ = 79.0 × 0.120 = 9.48. A loop gain near 10 leaves about one part in ten as error. More loop gain shrinks that row. It does nothing for the body-effect row.

The output resistance confirms the loop gain. The opened loop shows 17.4 kΩ and the closed loop 1.64 kΩ. The ratio is 10.6, close to 1 + T = 10.5.

Asked in interviews
  1. How do you find the loading of the feedback network in a series-shunt amplifier?

    For the input side, short the output node and look into the network from the input: here R1 ∥ RF. For the output side, open the input connection and look in from the output: here RF + R1.

  2. Why is the closed-loop gain below 1/β?

    The gain is A/(1 + Aβ), which is 1/β times T/(1 + T). With a loop gain of 9.5 that factor is 0.905. Loading lowers A, so it lowers T and makes the error larger.

  3. A feedback pair returns its signal to the source of an NMOS whose body is grounded. What changes?

    The source drives the transistor through gm + gmb, and the gate through gm only. The feedback factor grows by (gm + gmb)/gm. Here the gain target falls from 10 to 8.34.

Try It

The first block is the closed loop. The second block is the opened loop: the same transistors, with R1A and RFA loading the source of M1 and RFB plus R1B loading M2.

EHOLD copies the output level of the closed loop, so RFA carries the same DC current as RF. FDC copies the DC current of M1 into R1B. Both copies carry DC only, because the closed loop is silent when the opened loop is driven.

The let lines repeat the hand analysis with gm, gmb and gds read from the operating point. Four AC runs then measure the closed gain, the open gain and both output resistances.

Predict before each change. Make RD and RDO 120k and lower both DC inputs to keep M1 near 10 µA: does the last row of the budget shrink? Then set RF to 22 kΩ in all three places: how close to 10 does g_closed come?

SPICEngspice 42 · simulator service
Edit the netlist, then run it
Expected measurements: vout_dc = 1.263782e+00 vout_open_dc = 1.263782e+00 id1 = 1.970451e-05 id2 = 6.121866e-05 a1 = 9.678187e+00 a2 = 9.304888e+00 a_hand = 9.005445e+01 beta_eff = 1.199738e-01 t_hand = 1.080417e+01 g_hand = 7.629034e+00 g_closed = 7.468444e+00 a_open = 7.898575e+01 g_two_port = 7.539527e+00 rout_closed = 1.637840e+03 rout_open = 1.737593e+04

Check Yourself

Predict the outputAn ideal amplifier has a gain of 100 and 20 kΩ of output resistance. RF = 18 kΩ and R1 = 2 kΩ close the loop, and its input draws no current. Type the line meas prints for the closed-loop gain (format: g_closed = 1.234567e+00).
* an ideal amplifier with 20 k of output resistance, closed by RF = 18 k and R1 = 2 k
VIN in 0 DC 0 AC 1
EA x 0 in fb 100
RO x out 20k
RF out fb 18k
R1 fb 0 2k
.control
ac dec 5 100 10k
meas ac g_closed FIND vm(out) AT=1k
.endc
.end
ConceptRead the hook plot. How far is the flat part of the curve below the line that the resistor ratio promised?
ConceptFor a series-shunt loop, how do you find the load that the network puts on the amplifier's output?
ConceptThe designer wants the measured gain closer to 10 and doubles the loop gain. The body of M1 stays at ground. About what gain results?
ConceptThe opened loop has 17.4 kΩ of output resistance and the closed loop 1.64 kΩ. What does that ratio tell you?

Common Mistakes

Wrong Open the loop by removing the feedback network.

The network also loads the amplifier, so removing it gives an open-loop gain the closed circuit never has.

Fix Keep its loading: R1 ∥ RF at the source of M1 and RF + R1 at the output, and remove only the returned signal.

Wrong Lower the network resistance to make the feedback stronger.

The ratio sets β; a smaller network only loads the output stage and lowers the loop gain.

Fix Choose the ratio for the gain. Choose the level well above the output resistance the stage can drive.

Wrong Expect 1 + RF/R1 when the feedback returns to the source of an NMOS with a grounded body.

The source acts through gm + gmb, so the effective feedback factor here is 0.120 and the target is 8.34.

Fix Include gmb in the feedback factor, or use a device whose body is tied to its source.

Remember

  • A feedback network loads both ports of the amplifier. Count that load before you compute the loop gain.
  • Series-shunt: short the output to find the input-side load, and open the input connection to find the output-side load.
  • The closed-loop gain is A/(1 + Aβ), which is 1/β times T/(1 + T). A loop gain of 9.5 costs 9.5 %.
  • Feedback returned to the source of a grounded-body NMOS acts through gm + gmb. Here that moves the target from 10 to 8.34.
  • The ratio of the open-loop and closed-loop output resistances gives 1 + T directly.

Practice

Report a problem with this page