MDIO: Clause 22 Frames and Registers

Read and write a PHY's registers over two wires. Watch the line change hands in the turnaround, and see what a missing PHY looks like.

You Will Be Able To

  • Lay out a Clause 22 management frame field by field.
  • Say who drives MDIO in each bit of a read and of a write.
  • Use the turnaround bit to tell whether a PHY answered.
  • Read the control and status registers, including a latching bit.
Lesson
P11.15
Time
30 min
Runs on
Your browser
Check
5 questions

Every Ethernet PHY has registers: link up, speed, duplex, reset. The MAC chip reaches them over a slow two-wire bus called MDIO.

MDC at its fastestOne frameNo preambleAll 32 registers of one PHY
400 ns period25.6 µs12.8 µs819.2 µs

Bench arithmetic from the 400 ns minimum MDC period of 22.2.2.13.

Two Wires, One Talker at a Time

The station management entity (STA) in the MAC chip drives MDC, the clock. MDIO carries the data both ways. A PHY needs a pull-up on it, so an undriven line reads 1 (22.2.4.5.1).

One Management Bus, Many PHYsThe station management entity (STA) in the MAC chip drives MDC. MDIO is shared: whoever is not driving lets go, and a pull-up holds it at 1.
  • Manager
  • Channel / handshake
  • Subordinate
  • Transaction / TLM
One management bus, many PHYsThe station management entity (STA) in the MAC chip drives MDC. MDIO is shared: whoever is not driving lets go, and a pull-up holds it at 1. manager STA (MAC chip) drives MDC; mastersevery frame channel MDC and MDIO two wires, MDIOpulled up subordinate PHY address 1 32 registers subordinate PHY address 2 32 registers
  1. manager STA (MAC chip)drives MDC; masters every frame
    • MDC and MDIO
  2. channel MDC and MDIOtwo wires, MDIO pulled up
    • PHY address 1
    • PHY address 2
  3. subordinate PHY address 132 registers
  4. subordinate PHY address 232 registers
  1. Clock

    The STA drives MDC. Each MDC cycle carries one bit of the frame.

  2. Address

    Every PHY listens. Only the one whose address is in the frame answers.

  3. Answer

    On a read, the STA lets go of MDIO and the addressed PHY drives the data.

Read the diagram as text
  • STA (MAC chip): drives MDC; masters every frame
  • MDC and MDIO: two wires, MDIO pulled up
  • PHY address 1: 32 registers
  • PHY address 2: 32 registers
  • STA (MAC chip) → MDC and MDIO
  • MDC and MDIO → PHY address 1
  • MDC and MDIO → PHY address 2

IEEE Std 802.3-2022 22.2.2.13, 22.2.2.14 and 22.2.4.5. Up to 32 PHY addresses per bus. The bench PHY answers only its own address: a PHY on the 22.6 connector must also answer address 0 (22.2.4.5.5).

MDC may run no faster than a 400 ns period, with high and low times of at least 160 ns (22.2.2.13). The STA gives 10 ns of setup and hold around the rising edge of MDC. A PHY may take up to 300 ns to drive its answer (22.3.4).

The Frame

Every transaction is one frame of 64 bits, first bit on the left. Addresses and data go most significant bit first.

FieldBitsReadWriteWho drives
PRE3232 ones32 onesSTA
ST20101STA
OP21001STA
PHYAD5address, MSB firstthe sameSTA
REGAD5register, MSB firstthe sameSTA
TA2Z, then 01, then 0read: nobody, then the PHY; write: STA
DATA16register, bit 15 firstvalue, bit 15 firstread: PHY; write: STA
IDLEZ (the pull-up gives 1)Znobody

IEEE Std 802.3-2022 Table 22-12 and 22.2.4.5.1 to 22.2.4.5.8. 64 MDC cycles per frame.

The 32 ones of the preamble let a PHY find the start. A PHY must see all 32 before it answers (22.2.4.5.2).

ST is 01: the line drops from its idle 1 to 0, then rises again. OP picks read (10) or write (01). PHYAD picks one of 32 PHYs and REGAD one of its 32 registers.

The Turnaround

In a read, MDIO changes hands. The two turnaround bits keep the STA and the PHY from driving at the same time (22.2.4.5.7).

The Turnaround of a ReadCycles 44 to 51 of the read of register 2: the end of REGAD, both turnaround bits and the first data bits.
01234567masterdriveZPHYZdriveMDIO
Scroll horizontally ↔
  1. Cycle 1

    Cycle 45: the last REGAD bit, still driven by the master.

  2. Cycle 2

    Cycle 46: nobody drives. The pull-up holds MDIO at 1.

  3. Cycle 3

    Cycle 47: the PHY drives 0. That 0 proves a PHY is there.

  4. Cycle 4

    Cycle 48 on: the PHY sends bit 15 first. 1A2Bh starts 0, 0, 0, 1.

Bench run of the example (eth_mdio_phy at address 1).

In the first bit both let go. In the second, the PHY drives 0. In a write the STA drives both bits itself, 1 then 0.

If no PHY has that address, nobody drives the second bit and it reads 1. The data then reads FFFFh: all pull-up.

Registers 0 and 1

Register 0 is the control register and register 1 the status register in every Clause 22 PHY (22.2.4.5.6). Registers 2 and 3 hold the PHY identifier.

BitNameUse
0.15Reset1 resets the PHY; the bit clears itself
0.14Loopbackturn the PHY's data path back to the MAC
0.13, 0.6Speed selection00 10 Mb/s, 01 100 Mb/s, 10 1000 Mb/s
0.12Auto-Negotiation enable
0.11Power down
0.10Isolatecut the PHY off the MII
0.9Restart Auto-Negotiationclears itself
0.8Duplex mode1 full duplex (used when auto-negotiation is off)
0.7Collision test

Register 0, control (IEEE Std 802.3-2022 Table 22-7). The bits are read/write; 0.15 and 0.9 are self-clearing.

BitNameType
1.15 to 1.9abilities (100BASE-T4, 100BASE-X, 10 Mb/s, 100BASE-T2)read only
1.8Extended status in register 15read only
1.7Unidirectional abilityread only
1.6Accepts frames with no preambleread only
1.5Auto-Negotiation completeread only
1.4Remote faultlatching high
1.3Auto-Negotiation abilityread only
1.2Link statuslatching low
1.1Jabber detectlatching high
1.0Extended capabilityread only

Register 1, status (IEEE Std 802.3-2022 Table 22-8). A write to register 1 has no effect.

Link status, bit 1.2, latches low. A link failure clears it, and it stays clear until it is read (22.2.4.2.13). So one short drop is never missed.

Bench actionValue read
Read register 0 after reset1140h
Read register 1, link up792Dh (bit 2 = 1)
Link drops and comes back; read register 17929h (bit 2 = 0)
Read register 1 again792Dh (bit 2 = 1)
Write 8000h to register 0, read it1140h: reset done, bit 15 clear
Write 0000h to register 1, read it792Dh: unchanged

Bench PHY. The default 1140h (auto-negotiation on, full duplex, 1000 Mb/s) and the ability bits are bench choices.

The first read after a drop returned 7929h with bit 2 clear, although the link was back. The second read returned 792Dh.

When a Frame Goes Wrong

What the bench changedData readSecond turnaround bit
Nothing: 32 ones, PHY 1, register 21A2Bh0
Only 31 ones of preambleFFFFh1
No preamble; the PHY reports 1.6 = 0FFFFh1
No preamble; the PHY reports 1.6 = 11A2Bh0
Address 7: no PHY thereFFFFh1
PHY fault no_turnaround3456h0

Bench runs with a private frame task. 1A2Bh is the bench PHY's register 2. The bench stops MDC between frames, so idle does not count as preamble (legal: MDC is aperiodic, 22.2.2.13).

With 31 ones the PHY never synchronised, so it ignored the frame. A PHY that sets bit 1.6 accepts frames with no preamble at all (22.2.4.5.2). That halves the time per frame.

The no_turnaround PHY started its data one bit early. The STA still saw 0 in the turnaround, because bit 15 of 1A2Bh is 0. Yet it read 3456h: the value shifted left by one.

Try It

Each frame is written out field by field. Where en is 1 the master drives; elsewhere it lets go and the PHY or the pull-up decides MDIO.

The first frame reads register 2. The bench prints cycles 44 to 51, then the 16 data bits.

In the first frame's bits (not its en), change 32'hffffffff to 32'h7fffffff: a 0, then 31 ones. The PHY ignores the frame and the read gives ffff.

RUNIcarus Verilog · in your browser
Edit the code, then run it
Expected: cycle 44: master drives, PHY lets go, MDIO 1 cycle 45: master drives, PHY lets go, MDIO 0 cycle 46: master lets go, PHY lets go, MDIO 1 cycle 47: master lets go, PHY drives, MDIO 0 cycle 48: master lets go, PHY drives, MDIO 0 cycle 49: master lets go, PHY drives, MDIO 0 cycle 50: master lets go, PHY drives, MDIO 0 cycle 51: master lets go, PHY drives, MDIO 1 read PHY 1 register 2: 1a2b wrote 8001h to register 4, read back 8001
Read included file: hs_pkg.sv
`timescale 1ns/1ns
// hs_pkg.sv: shared pure functions, and the bench random generator (read-only).
package hs_pkg;
  // xorshift32 (Marsaglia 2003): a linear generator over GF(2), period 2^32 - 1. A zero state is
  // replaced by 1, because zero maps to itself.
  function automatic [31:0] xs32(input [31:0] s);
    reg [31:0] x;
    x = (s == 32'd0) ? 32'd1 : s;
    x = x ^ (x << 13); x = x ^ (x >> 17); x = x ^ (x << 5);
    return x;
  endfunction
  // A Fibonacci PRBS generator x^n + x^m + 1 (PRBS7: 7,6; PRBS9: 9,5; PRBS15: 15,14; PRBS23: 23,18;
  // PRBS31: 31,28). The output bit is s[n-1]; the next state shifts the feedback into bit 0.
  function automatic [31:0] prbs_next(input [31:0] s, input int n, input int m);
    reg fb;
    fb = s[n-1] ^ s[m-1];
    return ((s << 1) | {31'd0, fb}) & ((n == 32) ? 32'hffffffff : ((32'd1 << n) - 32'd1));
  endfunction
  function automatic int ones(input [63:0] v);
    int n; n = 0;
    for (int i = 0; i < 64; i++) n += v[i];
    return n;
  endfunction
  // GF(16) with x^4 + x + 1, and GF(1024) with x^10 + x^3 + 1: shift-and-add multiply, no tables.
  function automatic [3:0] gf16_mul(input [3:0] a, input [3:0] b);
    reg [3:0] p, x; p = 4'd0; x = a;
    for (int i = 0; i < 4; i++) begin
      if (b[i]) p = p ^ x;
      x = x[3] ? ({x[2:0], 1'b0} ^ 4'b0011) : {x[2:0], 1'b0};
    end
    return p;
  endfunction
  function automatic [3:0] gf16_pow(input int e);   // alpha^e, alpha = x
    reg [3:0] p; int k; p = 4'd1; k = e % 15; if (k < 0) k += 15;
    for (int i = 0; i < k; i++) p = gf16_mul(p, 4'd2);
    return p;
  endfunction
  function automatic int gf16_log(input [3:0] a);   // -1 for 0
    reg [3:0] p; p = 4'd1;
    if (a == 4'd0) return -1;
    for (int i = 0; i < 15; i++) begin if (p == a) return i; p = gf16_mul(p, 4'd2); end
    return -1;
  endfunction
  function automatic [9:0] gf1024_mul(input [9:0] a, input [9:0] b);
    reg [9:0] p, x; p = 10'd0; x = a;
    for (int i = 0; i < 10; i++) begin
      if (b[i]) p = p ^ x;
      x = x[9] ? ({x[8:0], 1'b0} ^ 10'b0000001001) : {x[8:0], 1'b0};
    end
    return p;
  endfunction
  function automatic [9:0] gf1024_pow(input int e);
    reg [9:0] p; int k; p = 10'd1; k = e % 1023; if (k < 0) k += 1023;
    for (int i = 0; i < k; i++) p = gf1024_mul(p, 10'd2);
    return p;
  endfunction
endpackage

// hs_rng: the bench's random numbers. Same seed, same numbers, on every engine.
module hs_rng;
  int unsigned s = 32'h2545f491;
  function automatic void seed(input int unsigned v); s = (v == 0) ? 32'd1 : v; endfunction
  function automatic int unsigned next(); s = hs_pkg::xs32(s); return s; endfunction
  function automatic int below(input int n); s = hs_pkg::xs32(s); return (n <= 0) ? 0 : int'(s % n); endfunction
  function automatic bit bit1(); s = hs_pkg::xs32(s); return s[16]; endfunction
  function automatic bit chance_ppm(input int ppm); s = hs_pkg::xs32(s); return (s % 1000000) < ppm; endfunction
  function automatic [7:0] byte8(); s = hs_pkg::xs32(s); return s[23:16]; endfunction
endmodule
Read included file: hs_code.sv
`timescale 1ns/1ns
// hs_code.sv: line codes, CRCs and scramblers (read-only).

// ---------------------------------------------------------------------------------------------
// hs_8b10b: 8b/10b encoder and decoder with running disparity and the 12 K codes.
// code[9:0] = {a,b,c,d,e,i,f,g,h,j}; bit a (code[9]) goes on the wire first. rd: 0 = RD-, 1 = RD+.
//   encode(d, k, rd_in) -> {rd_out, code[9:0]}            (11 bits)
//   decode(code, rd_in) -> {rd_out, disp_err, code_err, k, d[7:0]}   (12 bits)
//   enc(d, k) / dec(code): the same, with the running disparity kept in rd_tx / rd_rx
// A K request for a byte that is not one of the 12 K codes is encoded as data and counted in bad_k.
// Decoder: code_err = the code is in neither column of the table; disp_err = it is a valid code
// only in the other column. rd_out follows the sub-block rule on the received bits.
// Faults: no_rd (always the RD- column), a7_never (never the alternate D.x.A7),
//         keep_rd_on_unbalanced (the 4b sub-block is chosen with the disparity from before the 6b one),
//         no_balanced_flip (D.07 and D.x.3 keep their RD- form at RD+), dec_no_disp_check.
module hs_8b10b;
  bit no_rd = 0, a7_never = 0, keep_rd_on_unbalanced = 0, no_balanced_flip = 0, dec_no_disp_check = 0;
  bit trace = 0;
  bit rd_tx = 0, rd_rx = 0;
  int bad_k = 0, symbols = 0, code_errs = 0, disp_errs = 0;
  bit last_k = 0, last_code_err = 0, last_disp_err = 0;
  bit valid_m [0:1023]; bit valid_p [0:1023]; bit [8:0] kd [0:1023]; bit built = 0;
  function automatic [5:0] t6(input [4:0] x);   // 5b/6b, RD- column, abcdei
    case (x)
      5'd0: return 6'b100111;  5'd1: return 6'b011101;  5'd2: return 6'b101101;  5'd3: return 6'b110001;
      5'd4: return 6'b110101;  5'd5: return 6'b101001;  5'd6: return 6'b011001;  5'd7: return 6'b111000;
      5'd8: return 6'b111001;  5'd9: return 6'b100101;  5'd10: return 6'b010101; 5'd11: return 6'b110100;
      5'd12: return 6'b001101; 5'd13: return 6'b101100; 5'd14: return 6'b011100; 5'd15: return 6'b010111;
      5'd16: return 6'b011011; 5'd17: return 6'b100011; 5'd18: return 6'b010011; 5'd19: return 6'b110010;
      5'd20: return 6'b001011; 5'd21: return 6'b101010; 5'd22: return 6'b011010; 5'd23: return 6'b111010;
      5'd24: return 6'b110011; 5'd25: return 6'b100110; 5'd26: return 6'b010110; 5'd27: return 6'b110110;
      5'd28: return 6'b001110; 5'd29: return 6'b101110; 5'd30: return 6'b011110; default: return 6'b101011;
    endcase
  endfunction
  function automatic [3:0] t4d(input [2:0] y);  // 3b/4b data, RD- column, fghj (y = 7 is P7)
    case (y)
      3'd0: return 4'b1011; 3'd1: return 4'b1001; 3'd2: return 4'b0101; 3'd3: return 4'b1100;
      3'd4: return 4'b1101; 3'd5: return 4'b1010; 3'd6: return 4'b0110; default: return 4'b1110;
    endcase
  endfunction
  function automatic [3:0] t4k(input [2:0] y);  // 3b/4b for K codes, RD- form before the flip
    case (y)
      3'd0: return 4'b1011; 3'd1: return 4'b0110; 3'd2: return 4'b1010; 3'd3: return 4'b1100;
      3'd4: return 4'b1101; 3'd5: return 4'b0101; 3'd6: return 4'b1001; default: return 4'b0111;
    endcase
  endfunction
  function automatic bit k_ok(input [7:0] d);
    return d[4:0] == 5'd28 || d == 8'hf7 || d == 8'hfb || d == 8'hfd || d == 8'hfe;
  endfunction
  function automatic int n6(input [5:0] v); return v[0] + v[1] + v[2] + v[3] + v[4] + v[5]; endfunction
  function automatic int n4(input [3:0] v); return v[0] + v[1] + v[2] + v[3]; endfunction
  // running disparity at the end of a sub-block (more ones: +; more zeros: -; 000111 and 0011: +; 111000 and 1100: -)
  function automatic bit rd6(input [5:0] v, input bit rd);
    return (n6(v) > 3) ? 1'b1 : (n6(v) < 3) ? 1'b0 : (v == 6'b000111) ? 1'b1 : (v == 6'b111000) ? 1'b0 : rd;
  endfunction
  function automatic bit rd4(input [3:0] v, input bit rd);
    return (n4(v) > 2) ? 1'b1 : (n4(v) < 2) ? 1'b0 : (v == 4'b0011) ? 1'b1 : (v == 4'b1100) ? 1'b0 : rd;
  endfunction
  // faults: [0] no_rd [1] a7_never [2] keep_rd_on_unbalanced [3] no_balanced_flip
  function automatic [10:0] core(input [7:0] d, input bit k, input bit rd_in, input [3:0] f);
    reg [5:0] six; reg [3:0] four; reg rd0, r6, rd1, a7, kk; reg [4:0] x; reg [2:0] y; int o6, o4;
    x = d[4:0]; y = d[7:5]; kk = k && k_ok(d); rd0 = f[0] ? 1'b0 : rd_in;
    six = (kk && x == 5'd28) ? 6'b001111 : t6(x); o6 = n6(six);
    if (rd0 && (o6 != 3 || (six == 6'b111000 && !f[3]))) begin six = ~six; o6 = 6 - o6; end
    r6 = (o6 > 3) ? 1'b1 : (o6 < 3) ? 1'b0 : (six == 6'b000111) ? 1'b1 : (six == 6'b111000) ? 1'b0 : rd0;
    rd1 = f[2] ? rd0 : r6;
    if (kk) begin
      four = t4k(y); if (rd1) four = ~four;
    end else begin
      a7 = (y == 3'd7) && !f[1] && ((!rd1 && (x == 5'd17 || x == 5'd18 || x == 5'd20)) || (rd1 && (x == 5'd11 || x == 5'd13 || x == 5'd14)));
      four = a7 ? 4'b0111 : t4d(y);
      if (rd1 && (n4(four) != 2 || (four == 4'b1100 && !f[3]))) four = ~four;
    end
    o4 = n4(four);
    return {(o4 > 2) ? 1'b1 : (o4 < 2) ? 1'b0 : (four == 4'b0011) ? 1'b1 : (four == 4'b1100) ? 1'b0 : r6, six, four};
  endfunction
  function automatic [10:0] encode(input [7:0] d, input bit k, input bit rd_in);
    if (k && !k_ok(d)) bad_k++;
    return core(d, k, rd_in, {no_balanced_flip, keep_rd_on_unbalanced, a7_never, no_rd});
  endfunction
  function automatic void build();
    reg [10:0] c;
    for (int i = 0; i < 1024; i++) begin valid_m[i] = 0; valid_p[i] = 0; kd[i] = 9'd0; end
    for (int i = 0; i < 268; i++) begin
      reg [7:0] d; reg k;
      if (i < 256) begin d = i[7:0]; k = 0; end
      else begin k = 1; d = (i < 264) ? {3'(i - 256), 5'd28} : (i == 264) ? 8'hf7 : (i == 265) ? 8'hfb : (i == 266) ? 8'hfd : 8'hfe; end
      c = core(d, k, 1'b0, 4'd0); valid_m[c[9:0]] = 1; kd[c[9:0]] = {k, d};
      c = core(d, k, 1'b1, 4'd0); valid_p[c[9:0]] = 1; kd[c[9:0]] = {k, d};
    end
    built = 1;
  endfunction
  function automatic [11:0] decode(input [9:0] code, input bit rd_in);
    reg here, there, ce, de, r;
    if (!built) build();
    here = rd_in ? valid_p[code] : valid_m[code];
    there = rd_in ? valid_m[code] : valid_p[code];
    ce = !(here || there); de = !ce && !here && !dec_no_disp_check;
    r = rd4(code[3:0], rd6(code[9:4], rd_in));
    return {r, de, ce, ce ? 9'd0 : kd[code]};
  endfunction
  function automatic [9:0] enc(input [7:0] d, input bit k);
    reg [10:0] r; r = encode(d, k, rd_tx); rd_tx = r[10];
    if (trace) $display("s%0d TX %s%0d.%0d code=%b rd=%s", symbols, (k && k_ok(d)) ? "K" : "D", d[4:0], d[7:5], r[9:0], r[10] ? "+" : "-");
    symbols++;
    return r[9:0];
  endfunction
  function automatic [8:0] dec(input [9:0] code);
    reg [11:0] r; r = decode(code, rd_rx); rd_rx = r[11];
    last_disp_err = r[10]; last_code_err = r[9]; last_k = r[8];
    if (r[9]) code_errs++; if (r[10]) disp_errs++;
    if (trace && (r[9] || r[10])) $display("RX %b %s", code, r[9] ? "code error" : "disparity error");
    return r[8:0];
  endfunction
  function automatic bit comma7(input [6:0] w); return w == 7'b0011111 || w == 7'b1100000; endfunction
endmodule

// ---------------------------------------------------------------------------------------------
// hs_crc: a CRC of 1 to 32 bits with any polynomial, seed, bit order and final inversion.
// The register shifts left; the polynomial omits the x^width term. The field is sent register bit
// width-1 first (USB 2.0, USB 3.2 and Ethernet all send it this way).
//   use_crc32(), use_crc16_usb2(), use_crc5_usb2(), use_crc16_usb3(): parameter sets
//   reset(), crc_bit(b), crc_byte(v), crc_bits(v, n), field(), field_bit(i), check_value(), crc_residue_ok()
// Faults: msb_first (bytes enter MSB first), no_invert (the field is not complemented), seed_zero.
module hs_crc;
  int width = 32;
  bit [31:0] poly = 32'h04c11db7, seed = 32'hffffffff, residue = 32'hc704dd7b;
  bit lsb_first = 1, invert = 1;
  bit msb_first = 0, no_invert = 0, seed_zero = 0;
  bit [31:0] r = 32'hffffffff;
  function automatic [31:0] mask(); return (width >= 32) ? 32'hffffffff : ((32'd1 << width) - 32'd1); endfunction
  function automatic void reset(); r = seed_zero ? 32'd0 : (seed & mask()); endfunction
  function automatic void set(input int w, input [31:0] p, input [31:0] s, input [31:0] res, input bit lsb, input bit inv);
    width = w; poly = p; seed = s; residue = res; lsb_first = lsb; invert = inv; reset();
  endfunction
  function automatic void use_crc32();      set(32, 32'h04c11db7, 32'hffffffff, 32'hc704dd7b, 1, 1); endfunction
  function automatic void use_crc16_usb2(); set(16, 32'h8005, 32'hffff, 32'h800d, 1, 1); endfunction
  function automatic void use_crc5_usb2();  set(5, 32'h05, 32'h1f, 32'h0c, 1, 1); endfunction
  function automatic void use_crc16_usb3(); set(16, 32'h100b, 32'hffff, 32'hf6aa, 1, 1); endfunction
  function automatic void crc_bit(input bit b);
    reg fb; fb = b ^ r[width - 1];
    r = ((r << 1) ^ (fb ? poly : 32'd0)) & mask();
  endfunction
  function automatic void crc_byte(input [7:0] v);
    for (int i = 0; i < 8; i++) crc_bit(v[(lsb_first ^ msb_first) ? i : 7 - i]);
  endfunction
  function automatic void crc_bits(input [31:0] v, input int n);   // n bits of v, bit 0 first
    for (int i = 0; i < n; i++) crc_bit(v[i]);
  endfunction
  function automatic [31:0] field(); return (invert && !no_invert) ? (~r & mask()) : r; endfunction
  function automatic bit field_bit(input int i); reg [31:0] f; f = field(); return f[width - 1 - i]; endfunction
  // the usual published "check" number: the field with its first-sent bit read as bit 0
  function automatic [31:0] check_value();
    reg [31:0] f, o; f = field(); o = 32'd0;
    for (int i = 0; i < width; i++) o[i] = f[width - 1 - i];
    return lsb_first ? o : f;
  endfunction
  function automatic bit crc_residue_ok(); return r == (residue & mask()); endfunction
endmodule

// ---------------------------------------------------------------------------------------------
// hs_scr: additive (frame-synchronous) and multiplicative (self-synchronising) scramblers.
// poly holds the coefficients: bit k is x^k; the +1 term is always used (taps() sets bit 0); len is the degree.
// Additive: a Galois LFSR. The key bit is s[len-1]; each step shifts left and adds the low terms of
//   the polynomial when the key bit is 1. The data never enters the register.
// Multiplicative: the line bit is the data bit XOR the register bits at the polynomial's terms;
//   the scrambler shifts its own output in, the descrambler shifts the received line bit in.
//   scr_add(len, poly, seed), scr_mul(len, poly), use_usb3_gen1(), use_x58(), use_x23_usb3() (see its note)
//   scr_bit(b), dscr_bit(b), scr_byte(v), dscr_byte(v) (bit 0 first), scr_reset(), scr_hold() (a skip
//   symbol: no step), scr_unscrambled() (a symbol sent in the clear: 8 steps, data untouched)
// Faults: advance_on_skip (scr_hold steps the LFSR 8 times), no_reset (scr_reset does nothing),
//         wrong_tap (the lowest term x^k becomes x^(k+1)), seed_zero (scr_reset loads 0).
module hs_scr;
  bit mult = 0; int len = 16;
  bit [63:0] poly = 64'h10039, seed = 64'hffff;
  bit advance_on_skip = 0, no_reset = 0, wrong_tap = 0, seed_zero = 0;
  bit [63:0] s = 64'hffff;
  int steps = 0;
  function automatic [63:0] lmask(); return (len >= 64) ? 64'hffffffffffffffff : ((64'd1 << len) - 64'd1); endfunction
  function automatic [63:0] taps();
    reg [63:0] p; int k; p = poly | 64'd1; k = 1;
    if (wrong_tap) begin
      while (k < len && !p[k]) k++;
      if (k < len) begin p[k] = 1'b0; p[k + 1] = 1'b1; end
    end
    return p;
  endfunction
  function automatic void load(); s = (seed_zero ? 64'd0 : seed) & lmask(); endfunction
  function automatic void scr_add(input int n, input [63:0] p, input [63:0] sd); mult = 0; len = n; poly = p; seed = sd; s = sd & lmask(); endfunction
  function automatic void scr_mul(input int n, input [63:0] p); mult = 1; len = n; poly = p; seed = 64'd0; s = 64'd0; endfunction
  function automatic void use_usb3_gen1(); scr_add(16, 64'h10039, 64'hffff); endfunction   // x^16 + x^5 + x^4 + x^3 + 1, seed FFFFh
  function automatic void use_x58(); scr_mul(58, (64'd1 << 58) | (64'd1 << 39) | 64'd1); endfunction   // x^58 + x^39 + 1
  // USB 3.2 Gen 2 (§6.3.2.3) polynomial x^23 + x^21 + x^16 + x^8 + x^5 + x^2 + 1 with seed 1DBFBCh. Only the
  // polynomial and seed are the specification's: the register form here is this library's Galois form, and
  // the reset and bypass rules of §6.3.2.3 are not modelled, so do not quote its key stream as USB's.
  function automatic void use_x23_usb3(); scr_add(23, (64'd1 << 23) | (64'd1 << 21) | (64'd1 << 16) | (64'd1 << 8) | (64'd1 << 5) | (64'd1 << 2) | 64'd1, 64'h1dbfbc); endfunction
  function automatic void scr_reset(); if (!no_reset) load(); endfunction
  function automatic bit key(); return s[len - 1]; endfunction
  function automatic void step();
    reg kb; kb = s[len - 1];
    s = ((s << 1) & lmask()) ^ (kb ? (taps() & lmask()) : 64'd0);
    steps++;
  endfunction
  // the XOR of the register bits at the polynomial's terms x^1..x^len (bit k-1 of the register for x^k)
  function automatic bit fbx(input [63:0] st); return ^(st & (taps() >> 1) & lmask()); endfunction
  function automatic bit scr_bit(input bit b);
    reg o;
    if (!mult) begin o = b ^ s[len - 1]; step(); end
    else begin o = b ^ fbx(s); s = ((s << 1) | {63'd0, o}) & lmask(); steps++; end
    return o;
  endfunction
  function automatic bit dscr_bit(input bit b);
    reg o;
    if (!mult) begin o = b ^ s[len - 1]; step(); end
    else begin o = b ^ fbx(s); s = ((s << 1) | {63'd0, b}) & lmask(); steps++; end
    return o;
  endfunction
  function automatic [7:0] scr_byte(input [7:0] v);
    reg [7:0] o; for (int i = 0; i < 8; i++) o[i] = scr_bit(v[i]); return o;
  endfunction
  function automatic [7:0] dscr_byte(input [7:0] v);
    reg [7:0] o; for (int i = 0; i < 8; i++) o[i] = dscr_bit(v[i]); return o;
  endfunction
  // a skip symbol passes unscrambled and the LFSR holds
  function automatic void scr_hold(); if (advance_on_skip && !mult) for (int i = 0; i < 8; i++) step(); endfunction
  // another symbol that is sent unscrambled (a K code other than COM and SKP): the LFSR still steps 8 times
  function automatic void scr_unscrambled(); if (!mult) for (int i = 0; i < 8; i++) step(); endfunction
endmodule
Read included file: eth_mac.sv
`timescale 1ns/1ns
// eth_frame: one MAC frame as octets, its packet as wire bits, and a bit-serial receiver.
//   pay[i]                         client data, set by the bench before build()
//   build(da, sa, lt, len)         destination, source, Length/Type, len data octets, then the FCS -> oct[0..n-1].
//                                  It adds no pad: give it 46 data octets or more. (Padding is P11.2.1's task; the
//                                  pages show the padding MAC's frames as measured tables.)
//   wire_bits(), wire_bit(i)       the packet in transmit order: preamble, SFD, frame
//   rx_start(), rx_bit(b), rx_end()  hunt for the SFD, collect octets, then parse()
//   parse()                        da, sa, lt, is_length, is_type, data_len, fcs_rx, fcs_calc, fcs_ok
// Faults: fcs_msb_first, fcs_no_invert, fcs_covers_preamble, sfd_wrong, msb_first_octets.
module eth_frame;
  localparam int MIN_FRAME = 64, MAX_BASIC = 1518, MAX_QTAG = 1522, MAX_ENVELOPE = 2000;
  bit fcs_msb_first = 0, fcs_no_invert = 0, fcs_covers_preamble = 0, sfd_wrong = 0, msb_first_octets = 0;
  hs_crc crc();
  bit [7:0] pay [0:2047];
  bit [7:0] oct [0:2047];
  int n = 0;
  bit [47:0] da = 0, sa = 0; bit [15:0] lt = 0;
  bit is_length = 0, is_type = 0, fcs_ok = 0;
  int data_len = 0;
  bit [31:0] fcs_rx = 0, fcs_calc = 0;
  // receiver state
  bit in_frame = 0; bit [7:0] hist = 0, cur = 0; int nb = 0, excess = 0, sfd_at = -1, bits_seen = 0;

  // The FCS of oct[0..len-1] as four octets: the first octet sent is in [7:0].
  function automatic [31:0] fcs_of(input int len);
    crc.use_crc32(); crc.msb_first = fcs_msb_first; crc.no_invert = fcs_no_invert; crc.reset();
    if (fcs_covers_preamble) begin
      for (int i = 0; i < 7; i++) crc.crc_byte(8'h55);
      crc.crc_byte(8'hd5);
    end
    for (int i = 0; i < len; i++) crc.crc_byte(oct[i]);
    return crc.check_value();
  endfunction

  function automatic void build(input [47:0] d, input [47:0] s, input [15:0] t, input int len);
    int k; reg [31:0] f;
    k = 0;
    for (int i = 0; i < 6; i++) begin oct[k] = d[47 - 8*i -: 8]; k++; end
    for (int i = 0; i < 6; i++) begin oct[k] = s[47 - 8*i -: 8]; k++; end
    oct[k] = t[15:8]; k++;
    oct[k] = t[7:0]; k++;
    for (int i = 0; i < len; i++) begin oct[k] = pay[i]; k++; end
    f = fcs_of(k);
    for (int i = 0; i < 4; i++) begin oct[k] = f[8*i +: 8]; k++; end
    n = k; excess = 0;
    parse();
  endfunction

  function automatic void parse();
    da = 0; sa = 0; lt = 0; is_length = 0; is_type = 0; fcs_ok = 0; data_len = 0; fcs_rx = 0; fcs_calc = 0;
    if (n >= 14) begin
      da = {oct[0], oct[1], oct[2], oct[3], oct[4], oct[5]};
      sa = {oct[6], oct[7], oct[8], oct[9], oct[10], oct[11]};
      lt = {oct[12], oct[13]};
      is_length = (lt <= 16'd1500);
      is_type = (lt >= 16'd1536);
    end
    if (n >= 18) begin
      fcs_rx = {oct[n-1], oct[n-2], oct[n-3], oct[n-4]};
      fcs_calc = fcs_of(n - 4);
      fcs_ok = (fcs_rx == fcs_calc);
      data_len = is_length ? int'(lt) : n - 18;
    end
  endfunction

  function automatic int wire_bits(); return 8 * (8 + n); endfunction
  function automatic bit wire_bit(input int i);
    int o, b; reg [7:0] v;
    o = i / 8; b = i % 8;
    if (o < 7) v = 8'h55;
    else if (o == 7) v = sfd_wrong ? 8'h55 : 8'hd5;
    else v = oct[o - 8];
    return msb_first_octets ? v[7 - b] : v[b];
  endfunction

  function automatic void rx_start();
    in_frame = 0; hist = 0; cur = 0; nb = 0; n = 0; excess = 0; sfd_at = -1; bits_seen = 0;
  endfunction
  function automatic void rx_bit(input bit b);
    bits_seen++;
    if (!in_frame) begin
      hist = {hist[6:0], b};                      // the oldest bit is hist[7]
      if (hist == 8'b10101011) begin in_frame = 1; sfd_at = bits_seen; end
    end else begin
      if (msb_first_octets) cur[7 - nb] = b; else cur[nb] = b;
      nb++;
      if (nb == 8) begin oct[n] = cur; n++; nb = 0; end
    end
  endfunction
  function automatic void rx_end(); excess = nb; parse(); endfunction
endmodule
// eth_axis: a MAC client bus in the style of AXI4-Stream (IHI 0051B 2.2 handshake, 2.5 TKEEP, 2.6 TLAST, 2.9 TUSER),
// 64 bits wide. Byte 0 of a beat is tdata[7:0] and is first in the frame (AXI4-Stream 2.4.1). Bench conventions,
// not AXI4-Stream's or 802.3's: tkeep is all ones except on the last beat, where it covers bytes 0 to k-1; one tuser
// bit (transfer-based, 2.9.1), read on the last beat only, marks a bad frame (receive) or asks the MAC to abort it
// (transmit).
//   load(n)                  beats for octets oct[0..n-1]: bd[], bk[], bl[], nbeats; bv[] = valid per cycle, ncyc
//   tx_cycles()              the transmit MAC: one beat per cycle once a frame has started. Returns 0 sent,
//                            1 underrun (tvalid fell inside the frame), 2 aborted by tuser. sent_octets, fail_cycle.
// Fault: tvalid_gap (load() leaves cycle 3 of the frame empty: the client was late with a beat).
module eth_axis;
  bit tvalid_gap = 0;
  bit [7:0] oct [0:2047];
  bit [63:0] bd [0:300]; bit [7:0] bk [0:300]; bit bl [0:300]; bit bu [0:300];
  int nbeats = 0;
  bit bv [0:301]; int bix [0:301]; int ncyc = 0;
  int sent_octets = 0, fail_cycle = -1;
  function automatic void load(input int n);
    int b, k;
    nbeats = (n + 7) / 8;
    for (b = 0; b < nbeats; b++) begin
      bd[b] = 64'd0; bk[b] = 8'd0; bl[b] = (b == nbeats - 1); bu[b] = 0;
      for (k = 0; k < 8; k++) if (8*b + k < n) begin bd[b][8*k +: 8] = oct[8*b + k]; bk[b][k] = 1'b1; end
    end
    ncyc = 0;
    for (b = 0; b < nbeats; b++) begin
      if (tvalid_gap && b == 3) begin bv[ncyc] = 0; bix[ncyc] = -1; ncyc++; end
      bv[ncyc] = 1; bix[ncyc] = b; ncyc++;
    end
  endfunction
  function automatic int tx_cycles();
    bit started; started = 0; sent_octets = 0; fail_cycle = -1;
    for (int c = 0; c < ncyc; c++) begin
      if (!bv[c]) begin
        if (started) begin fail_cycle = c; return 1; end
      end else begin
        started = 1;
        if (bl[bix[c]] && bu[bix[c]]) begin fail_cycle = c; return 2; end
        for (int k = 0; k < 8; k++) if (bk[bix[c]][k]) sent_octets++;
      end
    end
    return 0;
  endfunction
endmodule

// eth_pause: the PAUSE function of MAC Control (Annex 31B) at the station that receives PAUSE frames, in octet
// times (one octet time is 8 bit times; a pause quantum is 512 bit times = 64 octet times, 31B.2).
//   reset(), rx_pause(t, q)  a valid PAUSE frame with pause_time q ended at time t: the timer restarts (31B.3.3)
//   may_start(t)             1 when a new data frame may start at time t. A frame already started is never cut
//                            (31B.3.7). react is the bench's reaction time: frames may still start until t + react.
//   paused_until             the time the timer runs out
//   pause_octets(q, o[])     not here: build a PAUSE frame with eth_frame (DA 01-80-C2-00-00-01, 8808h, 0001h, q)
// Faults: pause_ignored, pause_adds_not_overrides (a new frame adds to the timer, and zero does not cancel),
//         slow_reaction (react = 70 quanta, over the 60 allowed at 10 Gb/s), timer_in_bits (q counts bit times).
module eth_pause;
  localparam int QUANTUM = 64;                     // octet times
  bit pause_ignored = 0, pause_adds_not_overrides = 0, slow_reaction = 0, timer_in_bits = 0;
  int react = 0, t_rx = -1, paused_until = 0;
  function automatic void reset(); t_rx = -1; paused_until = 0; endfunction
  function automatic void rx_pause(input int t, input int q);
    int len;
    if (pause_ignored) return;
    len = timer_in_bits ? (q + 7) / 8 : q * QUANTUM;
    if (pause_adds_not_overrides && paused_until > t) paused_until = paused_until + len;
    else paused_until = t + len;
    t_rx = t;
  endfunction
  function automatic bit may_start(input int t);
    int r;
    r = slow_reaction ? 70 * QUANTUM : react;
    if (t_rx < 0) return 1;
    if (t < t_rx + r) return 1;
    return t >= paused_until;
  endfunction
endmodule

// eth_pfc: priority-based flow control (Annex 31D). The frame is 802.3's; holding a priority's queue is the MAC
// Control client's job (IEEE 802.1Q, not held), so the eight timers here are a bench client, in octet times.
//   build(f_oct[], pev, times[])   not here: the bench writes opcode 01-01, the vector and eight times into eth_frame
//   reset(), rx(t, pev, tm[0..7])  for each e[n] = 1 (bit n of the vector's low octet), priority n stops until
//                                  t + 64 * time[n] (hold_end[n]); e[n] = 0 leaves priority n alone; time[n] = 0 releases it
//   blocked(n, t)                  1 while priority n is held
// Fault: pfc_wrong_priority (reads e[n] from bit 7 - n).
module eth_pfc;
  bit pfc_wrong_priority = 0;
  int hold_end [0:7];
  function automatic void reset(); for (int i = 0; i < 8; i++) hold_end[i] = 0; endfunction
  function automatic void rx(input int t, input [15:0] pev, input [127:0] tm);   // tm[16*n +: 16] = time[n]
    bit e;
    for (int n = 0; n < 8; n++) begin
      e = pfc_wrong_priority ? pev[7 - n] : pev[n];
      if (e) hold_end[n] = t + 64 * int'(tm[16*n +: 16]);
    end
  endfunction
  function automatic bit blocked(input int n, input int t); return t < hold_end[n]; endfunction
endmodule

// eth_csma_tx: one half-duplex transmitter (4.2.3.2), one call of tick() per octet time.
//   reset(), load(frame_octets)   a frame of frame_octets (DA to FCS) waits to be sent; it is padded to min_frame
//   tick(carrier)                 carrier: another station's signal is on the wire here now. Returns 1 when the
//                                 station puts an octet (packet or jam) on the wire.
//   plan[i]                       the wait, in slots, after collision i + 1. The bench sets it (default 0). This
//                                 readable station draws nothing and has no attempt limit.
//   state  0 idle, 1 defer, 2 send, 3 jam, 4 backoff, 5 sent (as far as the sender knows)
//   pkt, sent, quiet, left, attempts, late, last_start, last_r
// min_frame is 64 octets; a bench may lower it to show why it is 64. Fault: no_backoff (every wait is 0 slots).
// Deference is a bench simplification: the 12-octet quiet count restarts on any carrier, own or received, and the
// station never starts while carrier is present. 4.2.8 restarts only the first part of the gap, and then transmits
// whatever the carrier.
module eth_csma_tx;
  localparam int SLOT = 64, JAM = 4, GAP = 12, PRE = 8;   // octet times
  bit no_backoff = 0;
  int min_frame = 64;
  int plan [0:63];
  int state = 0, pkt = 0, sent = 0, quiet = GAP, left = 0, attempts = 0, late = 0, last_start = -1, last_r = 0, now = 0;
  function automatic void reset();
    state = 0; pkt = 0; sent = 0; quiet = GAP; left = 0; attempts = 0; late = 0; last_start = -1; last_r = 0; now = 0;
  endfunction
  function automatic void load(input int frame_octets);
    pkt = PRE + frame_octets;
    if (frame_octets < min_frame) pkt = PRE + min_frame;
    state = 1; attempts = 0; sent = 0; late = 0;
  endfunction
  function automatic bit tick(input bit carrier);
    bit on;
    on = 0;
    if (state == 1 && !carrier && quiet >= GAP) begin state = 2; sent = 0; last_start = now; end
    if (state == 2 && carrier) begin
      attempts++; if (sent > SLOT) late++;
      state = 3; left = JAM;
    end
    case (state)
      2: begin sent++; on = 1; if (sent == pkt) state = 5; end
      3: begin
           on = 1; left--;
           if (left == 0) begin
             last_r = no_backoff ? 0 : plan[(attempts - 1) % 64];
             left = SLOT * last_r;
             state = (left == 0) ? 1 : 4;
           end
         end
      4: begin left--; if (left == 0) state = 1; end
      default: ;
    endcase
    quiet = (carrier || on) ? 0 : ((quiet < GAP) ? quiet + 1 : GAP);
    now++;
    return on;
  endfunction
endmodule

// eth_csma: two eth_csma_tx stations, A and B, at the two ends of a wire with a one-way delay of d octet times.
//   run(fa, ready_a, fb, ready_b, tmax)   each station loads its frame (fa, fb octets) at its ready time
//   on_a[t], on_b[t]          what each station put on the wire at time t
//   ev_t[], ev_who[] (0 A, 1 B), ev_kind[], ev_v[], n_ev   the event log:
//     kind 0 starts attempt v; 1 sees a collision after v octets; 2 jam over, backs off v slots;
//     3 last octet sent (v = octets); 4 gives up after v attempts
//   delivered(i)              1 when station i's last attempt reached the far end with no overlap there
//   a.plan[], b.plan[], a.no_backoff, b.no_backoff, a.min_frame, b.min_frame: the stations' settings
module eth_csma;
  eth_csma_tx a(); eth_csma_tx b();
  int d = 10, n_ev = 0, tend = 0;
  bit on_a [0:16383]; bit on_b [0:16383];
  int ev_t [0:255]; int ev_who [0:255]; int ev_kind [0:255]; int ev_v [0:255];
  function automatic void log_ev(input int t, input int who, input int kind, input int v);
    if (n_ev < 256) begin ev_t[n_ev] = t; ev_who[n_ev] = who; ev_kind[n_ev] = kind; ev_v[n_ev] = v; n_ev++; end
  endfunction
  function automatic void note(input int t, input int who, input int s0, input int s1, input int sent0, input int att, input int r, input int sent1);
    if (s0 != 2 && s1 == 2) log_ev(t, who, 0, att + 1);
    if (s0 == 2 && (s1 == 3 || s1 == 4)) log_ev(t, who, 1, sent0);
    if (s0 == 3 && (s1 == 4 || s1 == 1)) log_ev(t, who, 2, r);
    if (s0 != 5 && s1 == 5) log_ev(t, who, 3, sent1);
    if (s0 != 6 && s1 == 6) log_ev(t, who, 4, att);
  endfunction
  function automatic void run(input int fa, input int ready_a, input int fb, input int ready_b, input int tmax);
    bit ca, cb; int sa, sb, xa, xb;
    a.reset(); b.reset(); n_ev = 0; tend = tmax;
    for (int t = 0; t < tmax; t++) begin
      if (t == ready_a) a.load(fa);
      if (t == ready_b) b.load(fb);
      ca = (t >= d) ? on_b[t - d] : 1'b0;
      cb = (t >= d) ? on_a[t - d] : 1'b0;
      sa = a.state; sb = b.state; xa = a.sent; xb = b.sent;
      on_a[t] = a.tick(ca);
      on_b[t] = b.tick(cb);
      note(t, 0, sa, a.state, xa, a.attempts, a.last_r, a.sent);
      note(t, 1, sb, b.state, xb, b.attempts, b.last_r, b.sent);
    end
  endfunction
  function automatic bit delivered(input int i);
    int s, p, u;
    if (i == 0 && a.state != 5) return 0;
    if (i == 1 && b.state != 5) return 0;
    s = (i == 0) ? a.last_start : b.last_start;
    p = (i == 0) ? a.pkt : b.pkt;
    for (int t = s; t < s + p; t++) begin
      u = t + d;
      if (u < tend && ((i == 0) ? on_b[u] : on_a[u])) return 0;
    end
    return 1;
  endfunction
endmodule

// eth_gap: how long the gap before the next Start is on a 4-lane XGMII, where Start must sit on lane 0
// (46.3.1.4). A gap counts every character from the Terminate to the last idle before Start. A packet is
// 8 + n characters (Start, six preamble octets, SFD, an n-octet frame) and starts on lane 0.
//   reset()                     DIC = 0 (the count is reset only at initialisation)
//   method                      0 deficit idle count, 1 always insert (both allowed by 46.3.1.4)
//   next_gap(n, mac_gap)        the gap after an n-octet frame when the MAC asks for mac_gap (12 or more)
//   deleted, inserted, dic      what the last call did, and the count after it
// Faults: ipg_min_only (always deletes, ignoring the bound), dic_max4 (bounds the count at 4, not 3),
//         start_any_lane (no alignment: the gap is always mac_gap).
module eth_gap;
  bit ipg_min_only = 0, dic_max4 = 0, start_any_lane = 0;
  int method = 0, dic = 0, deleted = 0, inserted = 0;
  function automatic void reset(); dic = 0; deleted = 0; inserted = 0; endfunction
  function automatic int next_gap(input int n, input int mac_gap);
    int m, top;
    deleted = 0; inserted = 0;
    m = (n + mac_gap) % 4;                       // lanes past lane 0 the next Start would land on
    if (start_any_lane || m == 0) return mac_gap;
    top = dic_max4 ? 4 : 3;
    if (method == 0 && (ipg_min_only || dic + m <= top)) begin deleted = m; dic = dic + m; end
    else begin inserted = 4 - m; if (method == 0) dic = dic - (4 - m); end
    return mac_gap - deleted + inserted;
  endfunction
endmodule
Read included file: eth_mii.sv
`timescale 1ns/1ns
// eth_mii: one packet on the MII (4 bits per clock) and the GMII (8 bits per clock), transmit side only.
//   clear(), put(o), put_preamble()   the packet as octets: preamble and SFD, then the frame
//   err_beat                          the transmit beat on which TX_ER is asserted (-1: none)
//   mii_tx(i)   {tx_en, tx_er, txd[3:0]} on beat i: octet i/2, low nibble first (22.2.3); idle past the end
//   gmii_tx(i)  {tx_en, tx_er, txd[7:0]} on beat i
//   rgmii_tx(i) the same beat on RGMII: {ctl_rise, td_rise[3:0], ctl_fall, td_fall[3:0]}. Rising edge: TX_EN and
//               TXD<3:0>; falling edge: TX_EN XOR TX_ER and TXD<7:4>. RGMII is not an 802.3 interface: this mapping
//               follows RGMII Version 2.0, sections 3.2 (both clock edges) and 3.4 (the error coding).
// The receivers are graded (P11.13.1 GMII, P11.14.1 RGMII) and are kept out of this file.
module eth_mii;
  bit [7:0] pk [0:2047];
  int npk = 0, err_beat = -1;
  function automatic void clear(); npk = 0; err_beat = -1; endfunction
  function automatic void put(input [7:0] o); pk[npk] = o; npk++; endfunction
  function automatic void put_preamble(); for (int i = 0; i < 7; i++) put(8'h55); put(8'hd5); endfunction
  function automatic [5:0] mii_tx(input int i);
    if (i < 0 || i >= 2 * npk) return 6'd0;
    return {1'b1, i == err_beat, (i % 2 == 1) ? pk[i / 2][7:4] : pk[i / 2][3:0]};
  endfunction
  function automatic [9:0] gmii_tx(input int i);
    if (i < 0 || i >= npk) return 10'd0;
    return {1'b1, i == err_beat, pk[i]};
  endfunction
  function automatic [9:0] rgmii_tx(input int i);
    reg [9:0] g;
    g = gmii_tx(i);
    return {g[9], g[3:0], g[9] ^ g[8], g[7:4]};
  endfunction
endmodule

// eth_mdio_phy: one Clause 22 PHY on the MDIO bus (22.2.4.5), seen one MDC cycle at a time. The bench calls drive()
// to learn what the PHY puts on MDIO in this cycle, resolves the line (nobody driving: the pull-up gives 1), then
// calls sample(line) at the rising edge of MDC. The master (station management entity) is graded in P11.15.1 and is
// not in this file.
//   phyad                  this PHY's address (bench default 1); it answers no other address
//   pre_ok                 the PHY accepts a frame without the 32-one preamble (status bit 1.6)
//   reset(), set_link(up)  registers to bench defaults; the link goes up or down (1.2 latches low)
//   drive()                {oe, out}: the PHY drives in the second turnaround bit and the data of a read only
//   sample(line)           decodes ST, OP, PHYAD, REGAD; a write lands in the register after its 16th data bit
//   regs[0..31]            0 control (bench default 1140h; writing bit 15 resets it and the bit clears itself),
//                          1 status (read only, built by status()), 2 and 3 identifier (bench values 1A2Bh, 3C40h),
//                          4 to 31 plain storage. A read of register 1 returns the latch, then reloads it from link.
// Fault: no_turnaround (on a read the PHY drives D15 in the second turnaround bit, so its data comes one cycle early).
module eth_mdio_phy;
  bit no_turnaround = 0;
  bit [4:0] phyad = 5'd1;
  bit pre_ok = 0, link = 1, an_done = 1, link_lat = 1;
  bit [15:0] regs [0:31];
  int st = 0, ones = 0, k = 0, frames = 0;   // st: 0 hunt, 1 ST seen half, 2 header, 3 turnaround, 4 data, 5 not mine
  bit [11:0] hdr = 0; bit rd = 0; bit [15:0] sh = 0;
  // 1.14 to 1.11 abilities, 1.8 extended status, 1.6 preamble suppression, 1.5 AN complete, 1.3 AN ability,
  // 1.2 link status (latching low), 1.0 extended capability. The ability bits are the bench PHY's.
  function automatic [15:0] status(); return 16'h7909 | {9'd0, pre_ok, an_done, 2'b00, link_lat, 2'b00}; endfunction
  function automatic void reset();
    for (int i = 0; i < 32; i++) regs[i] = 16'h0000;
    regs[0] = 16'h1140; regs[2] = 16'h1a2b; regs[3] = 16'h3c40;
    link_lat = link; st = 0; ones = 0; k = 0; frames = 0;
  endfunction
  function automatic void set_link(input bit up); link = up; if (!up) link_lat = 0; endfunction
  function automatic [15:0] read_reg(input [4:0] r);
    reg [15:0] v;
    v = (r == 5'd1) ? status() : regs[r];
    if (r == 5'd1) link_lat = link;
    return v;
  endfunction
  function automatic void write_reg(input [4:0] r, input [15:0] v);
    if (r == 5'd1) return;
    if (r == 5'd0 && v[15]) begin regs[0] = 16'h1140; return; end
    regs[r] = v;
  endfunction
  function automatic [1:0] drive();
    if (st == 3 && rd && k == 1) return no_turnaround ? {1'b1, sh[15]} : 2'b10;
    if (st == 4 && rd) return {1'b1, sh[15]};
    return 2'b00;
  endfunction
  function automatic void sample(input bit line);
    case (st)
      0: if (line) ones++;
         else if (ones >= 32 || pre_ok) st = 1;
         else ones = 0;
      1: if (line) begin st = 2; k = 0; hdr = 0; end
         else begin st = 0; ones = 0; end
      2: begin
           hdr = {hdr[10:0], line}; k++;
           if (k == 12) begin
             k = 0;
             if (hdr[9:5] == phyad && (hdr[11:10] == 2'b10 || hdr[11:10] == 2'b01)) begin
               rd = (hdr[11:10] == 2'b10); st = 3; frames++;
               if (rd) sh = read_reg(hdr[4:0]);
             end
             else st = 5;
           end
         end
      3: if (k == 1) begin
           st = 4; k = 0;
           if (rd && no_turnaround) sh = {sh[14:0], 1'b0};
         end
         else k = 1;
      4: begin
           sh = rd ? {sh[14:0], 1'b0} : {sh[14:0], line};
           k++;
           if (k == 16) begin if (!rd) write_reg(hdr[4:0], sh); st = 0; ones = 0; k = 0; end
         end
      default: begin k++; if (k == 18) begin st = 0; ones = 0; k = 0; end end
    endcase
  endfunction
endmodule

// eth_mdio_mmd: one Clause 45 port (45.3), one frame at a time. A port holds up to 32 MMDs (MDIO manageable
// devices); each MMD has its own 16-bit address register, which an address frame sets and data frames use.
//   prtad                      the port address (bench 0); present[d] = 1 for each MMD in the package
//   reset()                    bench registers; every address register is unknown (x) again (45.3: undefined)
//   frame(st, op, pa, dev, d)  one frame; returns {answered, data}: data is the register for a read or a
//                              post-read-increment, the value written for a write, the new address for an address
//                              frame. ST 01 (a Clause 22 frame), another port or a missing MMD: {0, FFFFh}
//   OP: 00 address, 01 write, 11 read, 10 post-read-increment (stops at 65535)
//   Registers (bench values): m.5 devices in package; 1.0 and 3.0 control 1 (2040h); 1.1 and 3.1 status 1 (bit 2:
//   receive link, latching low); 3.32 BASE-R status 1 (1001h: link up, block lock); 3.33 BASE-R status 2 (bit 15
//   latched block lock; bits 7:0 errored blocks, cleared when read); 7.0 AN control (1000h); address 65535 of each
//   MMD holds FFF0h + d. Other addresses read 0000h; writes to addresses above 63 other than 65535 are dropped.
module eth_mdio_mmd;
  bit [4:0] prtad = 5'd0;
  bit present [0:31];
  logic [15:0] areg [0:31];
  bit [15:0] mem [0:2047];          // MMD d, address a (a < 64): mem[64 * d + a]
  bit [15:0] top [0:31];            // address 65535
  bit link = 1, link_lat1 = 1, link_lat3 = 1;
  bit [7:0] errs = 8'd5;
  function automatic void reset();
    for (int d = 0; d < 32; d++) begin present[d] = 0; areg[d] = 16'hxxxx; top[d] = 16'hfff0 + d; end
    for (int i = 0; i < 2048; i++) mem[i] = 16'h0000;
    present[1] = 1; present[3] = 1; present[7] = 1;
    for (int d = 0; d < 32; d++) if (present[d]) mem[64 * d + 5] = 16'h008a;   // MMDs 1, 3 and 7 in this package
    mem[64 + 0] = 16'h2040; mem[192 + 0] = 16'h2040; mem[192 + 32] = 16'h1001; mem[448 + 0] = 16'h1000;
    link = 1; link_lat1 = 1; link_lat3 = 1; errs = 8'd5;
  endfunction
  function automatic void set_link(input bit up); link = up; if (!up) begin link_lat1 = 0; link_lat3 = 0; end endfunction
  function automatic [15:0] get(input int d, input [15:0] a);
    reg [15:0] v;
    if (a == 16'hffff) return top[d];
    if (a > 63) return 16'h0000;
    v = mem[64 * d + a];
    if (d == 1 && a == 1) begin v = {13'd0, link_lat1, 2'b00}; link_lat1 = link; end
    if (d == 3 && a == 1) begin v = {13'd0, link_lat3, 2'b00}; link_lat3 = link; end
    if (d == 3 && a == 33) begin v = {link, 7'd0, errs}; errs = 8'd0; end
    return v;
  endfunction
  function automatic logic [16:0] frame(input [1:0] st, input [1:0] op, input [4:0] pa, input [4:0] dev, input [15:0] d);
    logic [15:0] a, v;
    if (st != 2'b00 || pa != prtad || !present[dev]) return {1'b0, 16'hffff};
    a = areg[dev];
    case (op)
      2'b00: begin areg[dev] = d; return {1'b1, d}; end
      2'b01: begin
               if (a === 16'hffff) top[dev] = d;
               else if (a < 64 && !(dev == 3 && (a == 1 || a == 32 || a == 33)) && !(dev == 1 && a == 1)) mem[64 * dev + a] = d;
               return {1'b1, d};
             end
      2'b11: begin if ($isunknown(a)) return {1'b1, 16'hxxxx}; return {1'b1, get(dev, a)}; end
      default: begin
               if ($isunknown(a)) return {1'b1, 16'hxxxx};
               v = get(dev, a);
               if (a != 16'hffff) areg[dev] = a + 16'd1;
               return {1'b1, v};
             end
    endcase
  endfunction
endmodule

Check Yourself

Predict the outputThe program sends one read frame. How many cycles does the master drive MDIO?
`timescale 1ns/1ns
module tb;
  eth_mdio_phy phy();               // the PHY at address 1
  reg [1:0] pd; bit line; reg [15:0] got; int drv;
  // One frame, cycle by cycle, bit 63 first. Where en is 1 the master drives bits; elsewhere it lets go.
  task automatic frame(input [63:0] bits, input [63:0] en, input bit show);
    got = 0; drv = 0;
    for (int i = 63; i >= 0; i--) begin
      pd = phy.drive();
      line = en[i] ? bits[i] : (pd[1] ? pd[0] : 1'b1);     // nobody driving: the pull-up reads 1
      if (en[i]) drv++;
      if (show && i <= 19 && i >= 12)
        $display("cycle %0d: master %0s, PHY %0s, MDIO %0d", 63 - i, en[i] ? "drives" : "lets go", pd[1] ? "drives" : "lets go", line);
      phy.sample(line);
      got = {got[14:0], line};
    end
  endtask
  initial begin
    phy.reset();
    frame({32'hffffffff, 2'b01, 2'b10, 5'd1, 5'd3, 18'h3ffff}, {32'hffffffff, 14'h3fff, 18'h00000}, 0);
    $display("%0d", drv);
    $finish;
  end
endmodule
Read included file: hs_pkg.sv
`timescale 1ns/1ns
// hs_pkg.sv: shared pure functions, and the bench random generator (read-only).
package hs_pkg;
  // xorshift32 (Marsaglia 2003): a linear generator over GF(2), period 2^32 - 1. A zero state is
  // replaced by 1, because zero maps to itself.
  function automatic [31:0] xs32(input [31:0] s);
    reg [31:0] x;
    x = (s == 32'd0) ? 32'd1 : s;
    x = x ^ (x << 13); x = x ^ (x >> 17); x = x ^ (x << 5);
    return x;
  endfunction
  // A Fibonacci PRBS generator x^n + x^m + 1 (PRBS7: 7,6; PRBS9: 9,5; PRBS15: 15,14; PRBS23: 23,18;
  // PRBS31: 31,28). The output bit is s[n-1]; the next state shifts the feedback into bit 0.
  function automatic [31:0] prbs_next(input [31:0] s, input int n, input int m);
    reg fb;
    fb = s[n-1] ^ s[m-1];
    return ((s << 1) | {31'd0, fb}) & ((n == 32) ? 32'hffffffff : ((32'd1 << n) - 32'd1));
  endfunction
  function automatic int ones(input [63:0] v);
    int n; n = 0;
    for (int i = 0; i < 64; i++) n += v[i];
    return n;
  endfunction
  // GF(16) with x^4 + x + 1, and GF(1024) with x^10 + x^3 + 1: shift-and-add multiply, no tables.
  function automatic [3:0] gf16_mul(input [3:0] a, input [3:0] b);
    reg [3:0] p, x; p = 4'd0; x = a;
    for (int i = 0; i < 4; i++) begin
      if (b[i]) p = p ^ x;
      x = x[3] ? ({x[2:0], 1'b0} ^ 4'b0011) : {x[2:0], 1'b0};
    end
    return p;
  endfunction
  function automatic [3:0] gf16_pow(input int e);   // alpha^e, alpha = x
    reg [3:0] p; int k; p = 4'd1; k = e % 15; if (k < 0) k += 15;
    for (int i = 0; i < k; i++) p = gf16_mul(p, 4'd2);
    return p;
  endfunction
  function automatic int gf16_log(input [3:0] a);   // -1 for 0
    reg [3:0] p; p = 4'd1;
    if (a == 4'd0) return -1;
    for (int i = 0; i < 15; i++) begin if (p == a) return i; p = gf16_mul(p, 4'd2); end
    return -1;
  endfunction
  function automatic [9:0] gf1024_mul(input [9:0] a, input [9:0] b);
    reg [9:0] p, x; p = 10'd0; x = a;
    for (int i = 0; i < 10; i++) begin
      if (b[i]) p = p ^ x;
      x = x[9] ? ({x[8:0], 1'b0} ^ 10'b0000001001) : {x[8:0], 1'b0};
    end
    return p;
  endfunction
  function automatic [9:0] gf1024_pow(input int e);
    reg [9:0] p; int k; p = 10'd1; k = e % 1023; if (k < 0) k += 1023;
    for (int i = 0; i < k; i++) p = gf1024_mul(p, 10'd2);
    return p;
  endfunction
endpackage

// hs_rng: the bench's random numbers. Same seed, same numbers, on every engine.
module hs_rng;
  int unsigned s = 32'h2545f491;
  function automatic void seed(input int unsigned v); s = (v == 0) ? 32'd1 : v; endfunction
  function automatic int unsigned next(); s = hs_pkg::xs32(s); return s; endfunction
  function automatic int below(input int n); s = hs_pkg::xs32(s); return (n <= 0) ? 0 : int'(s % n); endfunction
  function automatic bit bit1(); s = hs_pkg::xs32(s); return s[16]; endfunction
  function automatic bit chance_ppm(input int ppm); s = hs_pkg::xs32(s); return (s % 1000000) < ppm; endfunction
  function automatic [7:0] byte8(); s = hs_pkg::xs32(s); return s[23:16]; endfunction
endmodule
Read included file: hs_code.sv
`timescale 1ns/1ns
// hs_code.sv: line codes, CRCs and scramblers (read-only).

// ---------------------------------------------------------------------------------------------
// hs_8b10b: 8b/10b encoder and decoder with running disparity and the 12 K codes.
// code[9:0] = {a,b,c,d,e,i,f,g,h,j}; bit a (code[9]) goes on the wire first. rd: 0 = RD-, 1 = RD+.
//   encode(d, k, rd_in) -> {rd_out, code[9:0]}            (11 bits)
//   decode(code, rd_in) -> {rd_out, disp_err, code_err, k, d[7:0]}   (12 bits)
//   enc(d, k) / dec(code): the same, with the running disparity kept in rd_tx / rd_rx
// A K request for a byte that is not one of the 12 K codes is encoded as data and counted in bad_k.
// Decoder: code_err = the code is in neither column of the table; disp_err = it is a valid code
// only in the other column. rd_out follows the sub-block rule on the received bits.
// Faults: no_rd (always the RD- column), a7_never (never the alternate D.x.A7),
//         keep_rd_on_unbalanced (the 4b sub-block is chosen with the disparity from before the 6b one),
//         no_balanced_flip (D.07 and D.x.3 keep their RD- form at RD+), dec_no_disp_check.
module hs_8b10b;
  bit no_rd = 0, a7_never = 0, keep_rd_on_unbalanced = 0, no_balanced_flip = 0, dec_no_disp_check = 0;
  bit trace = 0;
  bit rd_tx = 0, rd_rx = 0;
  int bad_k = 0, symbols = 0, code_errs = 0, disp_errs = 0;
  bit last_k = 0, last_code_err = 0, last_disp_err = 0;
  bit valid_m [0:1023]; bit valid_p [0:1023]; bit [8:0] kd [0:1023]; bit built = 0;
  function automatic [5:0] t6(input [4:0] x);   // 5b/6b, RD- column, abcdei
    case (x)
      5'd0: return 6'b100111;  5'd1: return 6'b011101;  5'd2: return 6'b101101;  5'd3: return 6'b110001;
      5'd4: return 6'b110101;  5'd5: return 6'b101001;  5'd6: return 6'b011001;  5'd7: return 6'b111000;
      5'd8: return 6'b111001;  5'd9: return 6'b100101;  5'd10: return 6'b010101; 5'd11: return 6'b110100;
      5'd12: return 6'b001101; 5'd13: return 6'b101100; 5'd14: return 6'b011100; 5'd15: return 6'b010111;
      5'd16: return 6'b011011; 5'd17: return 6'b100011; 5'd18: return 6'b010011; 5'd19: return 6'b110010;
      5'd20: return 6'b001011; 5'd21: return 6'b101010; 5'd22: return 6'b011010; 5'd23: return 6'b111010;
      5'd24: return 6'b110011; 5'd25: return 6'b100110; 5'd26: return 6'b010110; 5'd27: return 6'b110110;
      5'd28: return 6'b001110; 5'd29: return 6'b101110; 5'd30: return 6'b011110; default: return 6'b101011;
    endcase
  endfunction
  function automatic [3:0] t4d(input [2:0] y);  // 3b/4b data, RD- column, fghj (y = 7 is P7)
    case (y)
      3'd0: return 4'b1011; 3'd1: return 4'b1001; 3'd2: return 4'b0101; 3'd3: return 4'b1100;
      3'd4: return 4'b1101; 3'd5: return 4'b1010; 3'd6: return 4'b0110; default: return 4'b1110;
    endcase
  endfunction
  function automatic [3:0] t4k(input [2:0] y);  // 3b/4b for K codes, RD- form before the flip
    case (y)
      3'd0: return 4'b1011; 3'd1: return 4'b0110; 3'd2: return 4'b1010; 3'd3: return 4'b1100;
      3'd4: return 4'b1101; 3'd5: return 4'b0101; 3'd6: return 4'b1001; default: return 4'b0111;
    endcase
  endfunction
  function automatic bit k_ok(input [7:0] d);
    return d[4:0] == 5'd28 || d == 8'hf7 || d == 8'hfb || d == 8'hfd || d == 8'hfe;
  endfunction
  function automatic int n6(input [5:0] v); return v[0] + v[1] + v[2] + v[3] + v[4] + v[5]; endfunction
  function automatic int n4(input [3:0] v); return v[0] + v[1] + v[2] + v[3]; endfunction
  // running disparity at the end of a sub-block (more ones: +; more zeros: -; 000111 and 0011: +; 111000 and 1100: -)
  function automatic bit rd6(input [5:0] v, input bit rd);
    return (n6(v) > 3) ? 1'b1 : (n6(v) < 3) ? 1'b0 : (v == 6'b000111) ? 1'b1 : (v == 6'b111000) ? 1'b0 : rd;
  endfunction
  function automatic bit rd4(input [3:0] v, input bit rd);
    return (n4(v) > 2) ? 1'b1 : (n4(v) < 2) ? 1'b0 : (v == 4'b0011) ? 1'b1 : (v == 4'b1100) ? 1'b0 : rd;
  endfunction
  // faults: [0] no_rd [1] a7_never [2] keep_rd_on_unbalanced [3] no_balanced_flip
  function automatic [10:0] core(input [7:0] d, input bit k, input bit rd_in, input [3:0] f);
    reg [5:0] six; reg [3:0] four; reg rd0, r6, rd1, a7, kk; reg [4:0] x; reg [2:0] y; int o6, o4;
    x = d[4:0]; y = d[7:5]; kk = k && k_ok(d); rd0 = f[0] ? 1'b0 : rd_in;
    six = (kk && x == 5'd28) ? 6'b001111 : t6(x); o6 = n6(six);
    if (rd0 && (o6 != 3 || (six == 6'b111000 && !f[3]))) begin six = ~six; o6 = 6 - o6; end
    r6 = (o6 > 3) ? 1'b1 : (o6 < 3) ? 1'b0 : (six == 6'b000111) ? 1'b1 : (six == 6'b111000) ? 1'b0 : rd0;
    rd1 = f[2] ? rd0 : r6;
    if (kk) begin
      four = t4k(y); if (rd1) four = ~four;
    end else begin
      a7 = (y == 3'd7) && !f[1] && ((!rd1 && (x == 5'd17 || x == 5'd18 || x == 5'd20)) || (rd1 && (x == 5'd11 || x == 5'd13 || x == 5'd14)));
      four = a7 ? 4'b0111 : t4d(y);
      if (rd1 && (n4(four) != 2 || (four == 4'b1100 && !f[3]))) four = ~four;
    end
    o4 = n4(four);
    return {(o4 > 2) ? 1'b1 : (o4 < 2) ? 1'b0 : (four == 4'b0011) ? 1'b1 : (four == 4'b1100) ? 1'b0 : r6, six, four};
  endfunction
  function automatic [10:0] encode(input [7:0] d, input bit k, input bit rd_in);
    if (k && !k_ok(d)) bad_k++;
    return core(d, k, rd_in, {no_balanced_flip, keep_rd_on_unbalanced, a7_never, no_rd});
  endfunction
  function automatic void build();
    reg [10:0] c;
    for (int i = 0; i < 1024; i++) begin valid_m[i] = 0; valid_p[i] = 0; kd[i] = 9'd0; end
    for (int i = 0; i < 268; i++) begin
      reg [7:0] d; reg k;
      if (i < 256) begin d = i[7:0]; k = 0; end
      else begin k = 1; d = (i < 264) ? {3'(i - 256), 5'd28} : (i == 264) ? 8'hf7 : (i == 265) ? 8'hfb : (i == 266) ? 8'hfd : 8'hfe; end
      c = core(d, k, 1'b0, 4'd0); valid_m[c[9:0]] = 1; kd[c[9:0]] = {k, d};
      c = core(d, k, 1'b1, 4'd0); valid_p[c[9:0]] = 1; kd[c[9:0]] = {k, d};
    end
    built = 1;
  endfunction
  function automatic [11:0] decode(input [9:0] code, input bit rd_in);
    reg here, there, ce, de, r;
    if (!built) build();
    here = rd_in ? valid_p[code] : valid_m[code];
    there = rd_in ? valid_m[code] : valid_p[code];
    ce = !(here || there); de = !ce && !here && !dec_no_disp_check;
    r = rd4(code[3:0], rd6(code[9:4], rd_in));
    return {r, de, ce, ce ? 9'd0 : kd[code]};
  endfunction
  function automatic [9:0] enc(input [7:0] d, input bit k);
    reg [10:0] r; r = encode(d, k, rd_tx); rd_tx = r[10];
    if (trace) $display("s%0d TX %s%0d.%0d code=%b rd=%s", symbols, (k && k_ok(d)) ? "K" : "D", d[4:0], d[7:5], r[9:0], r[10] ? "+" : "-");
    symbols++;
    return r[9:0];
  endfunction
  function automatic [8:0] dec(input [9:0] code);
    reg [11:0] r; r = decode(code, rd_rx); rd_rx = r[11];
    last_disp_err = r[10]; last_code_err = r[9]; last_k = r[8];
    if (r[9]) code_errs++; if (r[10]) disp_errs++;
    if (trace && (r[9] || r[10])) $display("RX %b %s", code, r[9] ? "code error" : "disparity error");
    return r[8:0];
  endfunction
  function automatic bit comma7(input [6:0] w); return w == 7'b0011111 || w == 7'b1100000; endfunction
endmodule

// ---------------------------------------------------------------------------------------------
// hs_crc: a CRC of 1 to 32 bits with any polynomial, seed, bit order and final inversion.
// The register shifts left; the polynomial omits the x^width term. The field is sent register bit
// width-1 first (USB 2.0, USB 3.2 and Ethernet all send it this way).
//   use_crc32(), use_crc16_usb2(), use_crc5_usb2(), use_crc16_usb3(): parameter sets
//   reset(), crc_bit(b), crc_byte(v), crc_bits(v, n), field(), field_bit(i), check_value(), crc_residue_ok()
// Faults: msb_first (bytes enter MSB first), no_invert (the field is not complemented), seed_zero.
module hs_crc;
  int width = 32;
  bit [31:0] poly = 32'h04c11db7, seed = 32'hffffffff, residue = 32'hc704dd7b;
  bit lsb_first = 1, invert = 1;
  bit msb_first = 0, no_invert = 0, seed_zero = 0;
  bit [31:0] r = 32'hffffffff;
  function automatic [31:0] mask(); return (width >= 32) ? 32'hffffffff : ((32'd1 << width) - 32'd1); endfunction
  function automatic void reset(); r = seed_zero ? 32'd0 : (seed & mask()); endfunction
  function automatic void set(input int w, input [31:0] p, input [31:0] s, input [31:0] res, input bit lsb, input bit inv);
    width = w; poly = p; seed = s; residue = res; lsb_first = lsb; invert = inv; reset();
  endfunction
  function automatic void use_crc32();      set(32, 32'h04c11db7, 32'hffffffff, 32'hc704dd7b, 1, 1); endfunction
  function automatic void use_crc16_usb2(); set(16, 32'h8005, 32'hffff, 32'h800d, 1, 1); endfunction
  function automatic void use_crc5_usb2();  set(5, 32'h05, 32'h1f, 32'h0c, 1, 1); endfunction
  function automatic void use_crc16_usb3(); set(16, 32'h100b, 32'hffff, 32'hf6aa, 1, 1); endfunction
  function automatic void crc_bit(input bit b);
    reg fb; fb = b ^ r[width - 1];
    r = ((r << 1) ^ (fb ? poly : 32'd0)) & mask();
  endfunction
  function automatic void crc_byte(input [7:0] v);
    for (int i = 0; i < 8; i++) crc_bit(v[(lsb_first ^ msb_first) ? i : 7 - i]);
  endfunction
  function automatic void crc_bits(input [31:0] v, input int n);   // n bits of v, bit 0 first
    for (int i = 0; i < n; i++) crc_bit(v[i]);
  endfunction
  function automatic [31:0] field(); return (invert && !no_invert) ? (~r & mask()) : r; endfunction
  function automatic bit field_bit(input int i); reg [31:0] f; f = field(); return f[width - 1 - i]; endfunction
  // the usual published "check" number: the field with its first-sent bit read as bit 0
  function automatic [31:0] check_value();
    reg [31:0] f, o; f = field(); o = 32'd0;
    for (int i = 0; i < width; i++) o[i] = f[width - 1 - i];
    return lsb_first ? o : f;
  endfunction
  function automatic bit crc_residue_ok(); return r == (residue & mask()); endfunction
endmodule

// ---------------------------------------------------------------------------------------------
// hs_scr: additive (frame-synchronous) and multiplicative (self-synchronising) scramblers.
// poly holds the coefficients: bit k is x^k; the +1 term is always used (taps() sets bit 0); len is the degree.
// Additive: a Galois LFSR. The key bit is s[len-1]; each step shifts left and adds the low terms of
//   the polynomial when the key bit is 1. The data never enters the register.
// Multiplicative: the line bit is the data bit XOR the register bits at the polynomial's terms;
//   the scrambler shifts its own output in, the descrambler shifts the received line bit in.
//   scr_add(len, poly, seed), scr_mul(len, poly), use_usb3_gen1(), use_x58(), use_x23_usb3() (see its note)
//   scr_bit(b), dscr_bit(b), scr_byte(v), dscr_byte(v) (bit 0 first), scr_reset(), scr_hold() (a skip
//   symbol: no step), scr_unscrambled() (a symbol sent in the clear: 8 steps, data untouched)
// Faults: advance_on_skip (scr_hold steps the LFSR 8 times), no_reset (scr_reset does nothing),
//         wrong_tap (the lowest term x^k becomes x^(k+1)), seed_zero (scr_reset loads 0).
module hs_scr;
  bit mult = 0; int len = 16;
  bit [63:0] poly = 64'h10039, seed = 64'hffff;
  bit advance_on_skip = 0, no_reset = 0, wrong_tap = 0, seed_zero = 0;
  bit [63:0] s = 64'hffff;
  int steps = 0;
  function automatic [63:0] lmask(); return (len >= 64) ? 64'hffffffffffffffff : ((64'd1 << len) - 64'd1); endfunction
  function automatic [63:0] taps();
    reg [63:0] p; int k; p = poly | 64'd1; k = 1;
    if (wrong_tap) begin
      while (k < len && !p[k]) k++;
      if (k < len) begin p[k] = 1'b0; p[k + 1] = 1'b1; end
    end
    return p;
  endfunction
  function automatic void load(); s = (seed_zero ? 64'd0 : seed) & lmask(); endfunction
  function automatic void scr_add(input int n, input [63:0] p, input [63:0] sd); mult = 0; len = n; poly = p; seed = sd; s = sd & lmask(); endfunction
  function automatic void scr_mul(input int n, input [63:0] p); mult = 1; len = n; poly = p; seed = 64'd0; s = 64'd0; endfunction
  function automatic void use_usb3_gen1(); scr_add(16, 64'h10039, 64'hffff); endfunction   // x^16 + x^5 + x^4 + x^3 + 1, seed FFFFh
  function automatic void use_x58(); scr_mul(58, (64'd1 << 58) | (64'd1 << 39) | 64'd1); endfunction   // x^58 + x^39 + 1
  // USB 3.2 Gen 2 (§6.3.2.3) polynomial x^23 + x^21 + x^16 + x^8 + x^5 + x^2 + 1 with seed 1DBFBCh. Only the
  // polynomial and seed are the specification's: the register form here is this library's Galois form, and
  // the reset and bypass rules of §6.3.2.3 are not modelled, so do not quote its key stream as USB's.
  function automatic void use_x23_usb3(); scr_add(23, (64'd1 << 23) | (64'd1 << 21) | (64'd1 << 16) | (64'd1 << 8) | (64'd1 << 5) | (64'd1 << 2) | 64'd1, 64'h1dbfbc); endfunction
  function automatic void scr_reset(); if (!no_reset) load(); endfunction
  function automatic bit key(); return s[len - 1]; endfunction
  function automatic void step();
    reg kb; kb = s[len - 1];
    s = ((s << 1) & lmask()) ^ (kb ? (taps() & lmask()) : 64'd0);
    steps++;
  endfunction
  // the XOR of the register bits at the polynomial's terms x^1..x^len (bit k-1 of the register for x^k)
  function automatic bit fbx(input [63:0] st); return ^(st & (taps() >> 1) & lmask()); endfunction
  function automatic bit scr_bit(input bit b);
    reg o;
    if (!mult) begin o = b ^ s[len - 1]; step(); end
    else begin o = b ^ fbx(s); s = ((s << 1) | {63'd0, o}) & lmask(); steps++; end
    return o;
  endfunction
  function automatic bit dscr_bit(input bit b);
    reg o;
    if (!mult) begin o = b ^ s[len - 1]; step(); end
    else begin o = b ^ fbx(s); s = ((s << 1) | {63'd0, b}) & lmask(); steps++; end
    return o;
  endfunction
  function automatic [7:0] scr_byte(input [7:0] v);
    reg [7:0] o; for (int i = 0; i < 8; i++) o[i] = scr_bit(v[i]); return o;
  endfunction
  function automatic [7:0] dscr_byte(input [7:0] v);
    reg [7:0] o; for (int i = 0; i < 8; i++) o[i] = dscr_bit(v[i]); return o;
  endfunction
  // a skip symbol passes unscrambled and the LFSR holds
  function automatic void scr_hold(); if (advance_on_skip && !mult) for (int i = 0; i < 8; i++) step(); endfunction
  // another symbol that is sent unscrambled (a K code other than COM and SKP): the LFSR still steps 8 times
  function automatic void scr_unscrambled(); if (!mult) for (int i = 0; i < 8; i++) step(); endfunction
endmodule
Read included file: eth_mac.sv
`timescale 1ns/1ns
// eth_frame: one MAC frame as octets, its packet as wire bits, and a bit-serial receiver.
//   pay[i]                         client data, set by the bench before build()
//   build(da, sa, lt, len)         destination, source, Length/Type, len data octets, then the FCS -> oct[0..n-1].
//                                  It adds no pad: give it 46 data octets or more. (Padding is P11.2.1's task; the
//                                  pages show the padding MAC's frames as measured tables.)
//   wire_bits(), wire_bit(i)       the packet in transmit order: preamble, SFD, frame
//   rx_start(), rx_bit(b), rx_end()  hunt for the SFD, collect octets, then parse()
//   parse()                        da, sa, lt, is_length, is_type, data_len, fcs_rx, fcs_calc, fcs_ok
// Faults: fcs_msb_first, fcs_no_invert, fcs_covers_preamble, sfd_wrong, msb_first_octets.
module eth_frame;
  localparam int MIN_FRAME = 64, MAX_BASIC = 1518, MAX_QTAG = 1522, MAX_ENVELOPE = 2000;
  bit fcs_msb_first = 0, fcs_no_invert = 0, fcs_covers_preamble = 0, sfd_wrong = 0, msb_first_octets = 0;
  hs_crc crc();
  bit [7:0] pay [0:2047];
  bit [7:0] oct [0:2047];
  int n = 0;
  bit [47:0] da = 0, sa = 0; bit [15:0] lt = 0;
  bit is_length = 0, is_type = 0, fcs_ok = 0;
  int data_len = 0;
  bit [31:0] fcs_rx = 0, fcs_calc = 0;
  // receiver state
  bit in_frame = 0; bit [7:0] hist = 0, cur = 0; int nb = 0, excess = 0, sfd_at = -1, bits_seen = 0;

  // The FCS of oct[0..len-1] as four octets: the first octet sent is in [7:0].
  function automatic [31:0] fcs_of(input int len);
    crc.use_crc32(); crc.msb_first = fcs_msb_first; crc.no_invert = fcs_no_invert; crc.reset();
    if (fcs_covers_preamble) begin
      for (int i = 0; i < 7; i++) crc.crc_byte(8'h55);
      crc.crc_byte(8'hd5);
    end
    for (int i = 0; i < len; i++) crc.crc_byte(oct[i]);
    return crc.check_value();
  endfunction

  function automatic void build(input [47:0] d, input [47:0] s, input [15:0] t, input int len);
    int k; reg [31:0] f;
    k = 0;
    for (int i = 0; i < 6; i++) begin oct[k] = d[47 - 8*i -: 8]; k++; end
    for (int i = 0; i < 6; i++) begin oct[k] = s[47 - 8*i -: 8]; k++; end
    oct[k] = t[15:8]; k++;
    oct[k] = t[7:0]; k++;
    for (int i = 0; i < len; i++) begin oct[k] = pay[i]; k++; end
    f = fcs_of(k);
    for (int i = 0; i < 4; i++) begin oct[k] = f[8*i +: 8]; k++; end
    n = k; excess = 0;
    parse();
  endfunction

  function automatic void parse();
    da = 0; sa = 0; lt = 0; is_length = 0; is_type = 0; fcs_ok = 0; data_len = 0; fcs_rx = 0; fcs_calc = 0;
    if (n >= 14) begin
      da = {oct[0], oct[1], oct[2], oct[3], oct[4], oct[5]};
      sa = {oct[6], oct[7], oct[8], oct[9], oct[10], oct[11]};
      lt = {oct[12], oct[13]};
      is_length = (lt <= 16'd1500);
      is_type = (lt >= 16'd1536);
    end
    if (n >= 18) begin
      fcs_rx = {oct[n-1], oct[n-2], oct[n-3], oct[n-4]};
      fcs_calc = fcs_of(n - 4);
      fcs_ok = (fcs_rx == fcs_calc);
      data_len = is_length ? int'(lt) : n - 18;
    end
  endfunction

  function automatic int wire_bits(); return 8 * (8 + n); endfunction
  function automatic bit wire_bit(input int i);
    int o, b; reg [7:0] v;
    o = i / 8; b = i % 8;
    if (o < 7) v = 8'h55;
    else if (o == 7) v = sfd_wrong ? 8'h55 : 8'hd5;
    else v = oct[o - 8];
    return msb_first_octets ? v[7 - b] : v[b];
  endfunction

  function automatic void rx_start();
    in_frame = 0; hist = 0; cur = 0; nb = 0; n = 0; excess = 0; sfd_at = -1; bits_seen = 0;
  endfunction
  function automatic void rx_bit(input bit b);
    bits_seen++;
    if (!in_frame) begin
      hist = {hist[6:0], b};                      // the oldest bit is hist[7]
      if (hist == 8'b10101011) begin in_frame = 1; sfd_at = bits_seen; end
    end else begin
      if (msb_first_octets) cur[7 - nb] = b; else cur[nb] = b;
      nb++;
      if (nb == 8) begin oct[n] = cur; n++; nb = 0; end
    end
  endfunction
  function automatic void rx_end(); excess = nb; parse(); endfunction
endmodule
// eth_axis: a MAC client bus in the style of AXI4-Stream (IHI 0051B 2.2 handshake, 2.5 TKEEP, 2.6 TLAST, 2.9 TUSER),
// 64 bits wide. Byte 0 of a beat is tdata[7:0] and is first in the frame (AXI4-Stream 2.4.1). Bench conventions,
// not AXI4-Stream's or 802.3's: tkeep is all ones except on the last beat, where it covers bytes 0 to k-1; one tuser
// bit (transfer-based, 2.9.1), read on the last beat only, marks a bad frame (receive) or asks the MAC to abort it
// (transmit).
//   load(n)                  beats for octets oct[0..n-1]: bd[], bk[], bl[], nbeats; bv[] = valid per cycle, ncyc
//   tx_cycles()              the transmit MAC: one beat per cycle once a frame has started. Returns 0 sent,
//                            1 underrun (tvalid fell inside the frame), 2 aborted by tuser. sent_octets, fail_cycle.
// Fault: tvalid_gap (load() leaves cycle 3 of the frame empty: the client was late with a beat).
module eth_axis;
  bit tvalid_gap = 0;
  bit [7:0] oct [0:2047];
  bit [63:0] bd [0:300]; bit [7:0] bk [0:300]; bit bl [0:300]; bit bu [0:300];
  int nbeats = 0;
  bit bv [0:301]; int bix [0:301]; int ncyc = 0;
  int sent_octets = 0, fail_cycle = -1;
  function automatic void load(input int n);
    int b, k;
    nbeats = (n + 7) / 8;
    for (b = 0; b < nbeats; b++) begin
      bd[b] = 64'd0; bk[b] = 8'd0; bl[b] = (b == nbeats - 1); bu[b] = 0;
      for (k = 0; k < 8; k++) if (8*b + k < n) begin bd[b][8*k +: 8] = oct[8*b + k]; bk[b][k] = 1'b1; end
    end
    ncyc = 0;
    for (b = 0; b < nbeats; b++) begin
      if (tvalid_gap && b == 3) begin bv[ncyc] = 0; bix[ncyc] = -1; ncyc++; end
      bv[ncyc] = 1; bix[ncyc] = b; ncyc++;
    end
  endfunction
  function automatic int tx_cycles();
    bit started; started = 0; sent_octets = 0; fail_cycle = -1;
    for (int c = 0; c < ncyc; c++) begin
      if (!bv[c]) begin
        if (started) begin fail_cycle = c; return 1; end
      end else begin
        started = 1;
        if (bl[bix[c]] && bu[bix[c]]) begin fail_cycle = c; return 2; end
        for (int k = 0; k < 8; k++) if (bk[bix[c]][k]) sent_octets++;
      end
    end
    return 0;
  endfunction
endmodule

// eth_pause: the PAUSE function of MAC Control (Annex 31B) at the station that receives PAUSE frames, in octet
// times (one octet time is 8 bit times; a pause quantum is 512 bit times = 64 octet times, 31B.2).
//   reset(), rx_pause(t, q)  a valid PAUSE frame with pause_time q ended at time t: the timer restarts (31B.3.3)
//   may_start(t)             1 when a new data frame may start at time t. A frame already started is never cut
//                            (31B.3.7). react is the bench's reaction time: frames may still start until t + react.
//   paused_until             the time the timer runs out
//   pause_octets(q, o[])     not here: build a PAUSE frame with eth_frame (DA 01-80-C2-00-00-01, 8808h, 0001h, q)
// Faults: pause_ignored, pause_adds_not_overrides (a new frame adds to the timer, and zero does not cancel),
//         slow_reaction (react = 70 quanta, over the 60 allowed at 10 Gb/s), timer_in_bits (q counts bit times).
module eth_pause;
  localparam int QUANTUM = 64;                     // octet times
  bit pause_ignored = 0, pause_adds_not_overrides = 0, slow_reaction = 0, timer_in_bits = 0;
  int react = 0, t_rx = -1, paused_until = 0;
  function automatic void reset(); t_rx = -1; paused_until = 0; endfunction
  function automatic void rx_pause(input int t, input int q);
    int len;
    if (pause_ignored) return;
    len = timer_in_bits ? (q + 7) / 8 : q * QUANTUM;
    if (pause_adds_not_overrides && paused_until > t) paused_until = paused_until + len;
    else paused_until = t + len;
    t_rx = t;
  endfunction
  function automatic bit may_start(input int t);
    int r;
    r = slow_reaction ? 70 * QUANTUM : react;
    if (t_rx < 0) return 1;
    if (t < t_rx + r) return 1;
    return t >= paused_until;
  endfunction
endmodule

// eth_pfc: priority-based flow control (Annex 31D). The frame is 802.3's; holding a priority's queue is the MAC
// Control client's job (IEEE 802.1Q, not held), so the eight timers here are a bench client, in octet times.
//   build(f_oct[], pev, times[])   not here: the bench writes opcode 01-01, the vector and eight times into eth_frame
//   reset(), rx(t, pev, tm[0..7])  for each e[n] = 1 (bit n of the vector's low octet), priority n stops until
//                                  t + 64 * time[n] (hold_end[n]); e[n] = 0 leaves priority n alone; time[n] = 0 releases it
//   blocked(n, t)                  1 while priority n is held
// Fault: pfc_wrong_priority (reads e[n] from bit 7 - n).
module eth_pfc;
  bit pfc_wrong_priority = 0;
  int hold_end [0:7];
  function automatic void reset(); for (int i = 0; i < 8; i++) hold_end[i] = 0; endfunction
  function automatic void rx(input int t, input [15:0] pev, input [127:0] tm);   // tm[16*n +: 16] = time[n]
    bit e;
    for (int n = 0; n < 8; n++) begin
      e = pfc_wrong_priority ? pev[7 - n] : pev[n];
      if (e) hold_end[n] = t + 64 * int'(tm[16*n +: 16]);
    end
  endfunction
  function automatic bit blocked(input int n, input int t); return t < hold_end[n]; endfunction
endmodule

// eth_csma_tx: one half-duplex transmitter (4.2.3.2), one call of tick() per octet time.
//   reset(), load(frame_octets)   a frame of frame_octets (DA to FCS) waits to be sent; it is padded to min_frame
//   tick(carrier)                 carrier: another station's signal is on the wire here now. Returns 1 when the
//                                 station puts an octet (packet or jam) on the wire.
//   plan[i]                       the wait, in slots, after collision i + 1. The bench sets it (default 0). This
//                                 readable station draws nothing and has no attempt limit.
//   state  0 idle, 1 defer, 2 send, 3 jam, 4 backoff, 5 sent (as far as the sender knows)
//   pkt, sent, quiet, left, attempts, late, last_start, last_r
// min_frame is 64 octets; a bench may lower it to show why it is 64. Fault: no_backoff (every wait is 0 slots).
// Deference is a bench simplification: the 12-octet quiet count restarts on any carrier, own or received, and the
// station never starts while carrier is present. 4.2.8 restarts only the first part of the gap, and then transmits
// whatever the carrier.
module eth_csma_tx;
  localparam int SLOT = 64, JAM = 4, GAP = 12, PRE = 8;   // octet times
  bit no_backoff = 0;
  int min_frame = 64;
  int plan [0:63];
  int state = 0, pkt = 0, sent = 0, quiet = GAP, left = 0, attempts = 0, late = 0, last_start = -1, last_r = 0, now = 0;
  function automatic void reset();
    state = 0; pkt = 0; sent = 0; quiet = GAP; left = 0; attempts = 0; late = 0; last_start = -1; last_r = 0; now = 0;
  endfunction
  function automatic void load(input int frame_octets);
    pkt = PRE + frame_octets;
    if (frame_octets < min_frame) pkt = PRE + min_frame;
    state = 1; attempts = 0; sent = 0; late = 0;
  endfunction
  function automatic bit tick(input bit carrier);
    bit on;
    on = 0;
    if (state == 1 && !carrier && quiet >= GAP) begin state = 2; sent = 0; last_start = now; end
    if (state == 2 && carrier) begin
      attempts++; if (sent > SLOT) late++;
      state = 3; left = JAM;
    end
    case (state)
      2: begin sent++; on = 1; if (sent == pkt) state = 5; end
      3: begin
           on = 1; left--;
           if (left == 0) begin
             last_r = no_backoff ? 0 : plan[(attempts - 1) % 64];
             left = SLOT * last_r;
             state = (left == 0) ? 1 : 4;
           end
         end
      4: begin left--; if (left == 0) state = 1; end
      default: ;
    endcase
    quiet = (carrier || on) ? 0 : ((quiet < GAP) ? quiet + 1 : GAP);
    now++;
    return on;
  endfunction
endmodule

// eth_csma: two eth_csma_tx stations, A and B, at the two ends of a wire with a one-way delay of d octet times.
//   run(fa, ready_a, fb, ready_b, tmax)   each station loads its frame (fa, fb octets) at its ready time
//   on_a[t], on_b[t]          what each station put on the wire at time t
//   ev_t[], ev_who[] (0 A, 1 B), ev_kind[], ev_v[], n_ev   the event log:
//     kind 0 starts attempt v; 1 sees a collision after v octets; 2 jam over, backs off v slots;
//     3 last octet sent (v = octets); 4 gives up after v attempts
//   delivered(i)              1 when station i's last attempt reached the far end with no overlap there
//   a.plan[], b.plan[], a.no_backoff, b.no_backoff, a.min_frame, b.min_frame: the stations' settings
module eth_csma;
  eth_csma_tx a(); eth_csma_tx b();
  int d = 10, n_ev = 0, tend = 0;
  bit on_a [0:16383]; bit on_b [0:16383];
  int ev_t [0:255]; int ev_who [0:255]; int ev_kind [0:255]; int ev_v [0:255];
  function automatic void log_ev(input int t, input int who, input int kind, input int v);
    if (n_ev < 256) begin ev_t[n_ev] = t; ev_who[n_ev] = who; ev_kind[n_ev] = kind; ev_v[n_ev] = v; n_ev++; end
  endfunction
  function automatic void note(input int t, input int who, input int s0, input int s1, input int sent0, input int att, input int r, input int sent1);
    if (s0 != 2 && s1 == 2) log_ev(t, who, 0, att + 1);
    if (s0 == 2 && (s1 == 3 || s1 == 4)) log_ev(t, who, 1, sent0);
    if (s0 == 3 && (s1 == 4 || s1 == 1)) log_ev(t, who, 2, r);
    if (s0 != 5 && s1 == 5) log_ev(t, who, 3, sent1);
    if (s0 != 6 && s1 == 6) log_ev(t, who, 4, att);
  endfunction
  function automatic void run(input int fa, input int ready_a, input int fb, input int ready_b, input int tmax);
    bit ca, cb; int sa, sb, xa, xb;
    a.reset(); b.reset(); n_ev = 0; tend = tmax;
    for (int t = 0; t < tmax; t++) begin
      if (t == ready_a) a.load(fa);
      if (t == ready_b) b.load(fb);
      ca = (t >= d) ? on_b[t - d] : 1'b0;
      cb = (t >= d) ? on_a[t - d] : 1'b0;
      sa = a.state; sb = b.state; xa = a.sent; xb = b.sent;
      on_a[t] = a.tick(ca);
      on_b[t] = b.tick(cb);
      note(t, 0, sa, a.state, xa, a.attempts, a.last_r, a.sent);
      note(t, 1, sb, b.state, xb, b.attempts, b.last_r, b.sent);
    end
  endfunction
  function automatic bit delivered(input int i);
    int s, p, u;
    if (i == 0 && a.state != 5) return 0;
    if (i == 1 && b.state != 5) return 0;
    s = (i == 0) ? a.last_start : b.last_start;
    p = (i == 0) ? a.pkt : b.pkt;
    for (int t = s; t < s + p; t++) begin
      u = t + d;
      if (u < tend && ((i == 0) ? on_b[u] : on_a[u])) return 0;
    end
    return 1;
  endfunction
endmodule

// eth_gap: how long the gap before the next Start is on a 4-lane XGMII, where Start must sit on lane 0
// (46.3.1.4). A gap counts every character from the Terminate to the last idle before Start. A packet is
// 8 + n characters (Start, six preamble octets, SFD, an n-octet frame) and starts on lane 0.
//   reset()                     DIC = 0 (the count is reset only at initialisation)
//   method                      0 deficit idle count, 1 always insert (both allowed by 46.3.1.4)
//   next_gap(n, mac_gap)        the gap after an n-octet frame when the MAC asks for mac_gap (12 or more)
//   deleted, inserted, dic      what the last call did, and the count after it
// Faults: ipg_min_only (always deletes, ignoring the bound), dic_max4 (bounds the count at 4, not 3),
//         start_any_lane (no alignment: the gap is always mac_gap).
module eth_gap;
  bit ipg_min_only = 0, dic_max4 = 0, start_any_lane = 0;
  int method = 0, dic = 0, deleted = 0, inserted = 0;
  function automatic void reset(); dic = 0; deleted = 0; inserted = 0; endfunction
  function automatic int next_gap(input int n, input int mac_gap);
    int m, top;
    deleted = 0; inserted = 0;
    m = (n + mac_gap) % 4;                       // lanes past lane 0 the next Start would land on
    if (start_any_lane || m == 0) return mac_gap;
    top = dic_max4 ? 4 : 3;
    if (method == 0 && (ipg_min_only || dic + m <= top)) begin deleted = m; dic = dic + m; end
    else begin inserted = 4 - m; if (method == 0) dic = dic - (4 - m); end
    return mac_gap - deleted + inserted;
  endfunction
endmodule
Read included file: eth_mii.sv
`timescale 1ns/1ns
// eth_mii: one packet on the MII (4 bits per clock) and the GMII (8 bits per clock), transmit side only.
//   clear(), put(o), put_preamble()   the packet as octets: preamble and SFD, then the frame
//   err_beat                          the transmit beat on which TX_ER is asserted (-1: none)
//   mii_tx(i)   {tx_en, tx_er, txd[3:0]} on beat i: octet i/2, low nibble first (22.2.3); idle past the end
//   gmii_tx(i)  {tx_en, tx_er, txd[7:0]} on beat i
//   rgmii_tx(i) the same beat on RGMII: {ctl_rise, td_rise[3:0], ctl_fall, td_fall[3:0]}. Rising edge: TX_EN and
//               TXD<3:0>; falling edge: TX_EN XOR TX_ER and TXD<7:4>. RGMII is not an 802.3 interface: this mapping
//               follows RGMII Version 2.0, sections 3.2 (both clock edges) and 3.4 (the error coding).
// The receivers are graded (P11.13.1 GMII, P11.14.1 RGMII) and are kept out of this file.
module eth_mii;
  bit [7:0] pk [0:2047];
  int npk = 0, err_beat = -1;
  function automatic void clear(); npk = 0; err_beat = -1; endfunction
  function automatic void put(input [7:0] o); pk[npk] = o; npk++; endfunction
  function automatic void put_preamble(); for (int i = 0; i < 7; i++) put(8'h55); put(8'hd5); endfunction
  function automatic [5:0] mii_tx(input int i);
    if (i < 0 || i >= 2 * npk) return 6'd0;
    return {1'b1, i == err_beat, (i % 2 == 1) ? pk[i / 2][7:4] : pk[i / 2][3:0]};
  endfunction
  function automatic [9:0] gmii_tx(input int i);
    if (i < 0 || i >= npk) return 10'd0;
    return {1'b1, i == err_beat, pk[i]};
  endfunction
  function automatic [9:0] rgmii_tx(input int i);
    reg [9:0] g;
    g = gmii_tx(i);
    return {g[9], g[3:0], g[9] ^ g[8], g[7:4]};
  endfunction
endmodule

// eth_mdio_phy: one Clause 22 PHY on the MDIO bus (22.2.4.5), seen one MDC cycle at a time. The bench calls drive()
// to learn what the PHY puts on MDIO in this cycle, resolves the line (nobody driving: the pull-up gives 1), then
// calls sample(line) at the rising edge of MDC. The master (station management entity) is graded in P11.15.1 and is
// not in this file.
//   phyad                  this PHY's address (bench default 1); it answers no other address
//   pre_ok                 the PHY accepts a frame without the 32-one preamble (status bit 1.6)
//   reset(), set_link(up)  registers to bench defaults; the link goes up or down (1.2 latches low)
//   drive()                {oe, out}: the PHY drives in the second turnaround bit and the data of a read only
//   sample(line)           decodes ST, OP, PHYAD, REGAD; a write lands in the register after its 16th data bit
//   regs[0..31]            0 control (bench default 1140h; writing bit 15 resets it and the bit clears itself),
//                          1 status (read only, built by status()), 2 and 3 identifier (bench values 1A2Bh, 3C40h),
//                          4 to 31 plain storage. A read of register 1 returns the latch, then reloads it from link.
// Fault: no_turnaround (on a read the PHY drives D15 in the second turnaround bit, so its data comes one cycle early).
module eth_mdio_phy;
  bit no_turnaround = 0;
  bit [4:0] phyad = 5'd1;
  bit pre_ok = 0, link = 1, an_done = 1, link_lat = 1;
  bit [15:0] regs [0:31];
  int st = 0, ones = 0, k = 0, frames = 0;   // st: 0 hunt, 1 ST seen half, 2 header, 3 turnaround, 4 data, 5 not mine
  bit [11:0] hdr = 0; bit rd = 0; bit [15:0] sh = 0;
  // 1.14 to 1.11 abilities, 1.8 extended status, 1.6 preamble suppression, 1.5 AN complete, 1.3 AN ability,
  // 1.2 link status (latching low), 1.0 extended capability. The ability bits are the bench PHY's.
  function automatic [15:0] status(); return 16'h7909 | {9'd0, pre_ok, an_done, 2'b00, link_lat, 2'b00}; endfunction
  function automatic void reset();
    for (int i = 0; i < 32; i++) regs[i] = 16'h0000;
    regs[0] = 16'h1140; regs[2] = 16'h1a2b; regs[3] = 16'h3c40;
    link_lat = link; st = 0; ones = 0; k = 0; frames = 0;
  endfunction
  function automatic void set_link(input bit up); link = up; if (!up) link_lat = 0; endfunction
  function automatic [15:0] read_reg(input [4:0] r);
    reg [15:0] v;
    v = (r == 5'd1) ? status() : regs[r];
    if (r == 5'd1) link_lat = link;
    return v;
  endfunction
  function automatic void write_reg(input [4:0] r, input [15:0] v);
    if (r == 5'd1) return;
    if (r == 5'd0 && v[15]) begin regs[0] = 16'h1140; return; end
    regs[r] = v;
  endfunction
  function automatic [1:0] drive();
    if (st == 3 && rd && k == 1) return no_turnaround ? {1'b1, sh[15]} : 2'b10;
    if (st == 4 && rd) return {1'b1, sh[15]};
    return 2'b00;
  endfunction
  function automatic void sample(input bit line);
    case (st)
      0: if (line) ones++;
         else if (ones >= 32 || pre_ok) st = 1;
         else ones = 0;
      1: if (line) begin st = 2; k = 0; hdr = 0; end
         else begin st = 0; ones = 0; end
      2: begin
           hdr = {hdr[10:0], line}; k++;
           if (k == 12) begin
             k = 0;
             if (hdr[9:5] == phyad && (hdr[11:10] == 2'b10 || hdr[11:10] == 2'b01)) begin
               rd = (hdr[11:10] == 2'b10); st = 3; frames++;
               if (rd) sh = read_reg(hdr[4:0]);
             end
             else st = 5;
           end
         end
      3: if (k == 1) begin
           st = 4; k = 0;
           if (rd && no_turnaround) sh = {sh[14:0], 1'b0};
         end
         else k = 1;
      4: begin
           sh = rd ? {sh[14:0], 1'b0} : {sh[14:0], line};
           k++;
           if (k == 16) begin if (!rd) write_reg(hdr[4:0], sh); st = 0; ones = 0; k = 0; end
         end
      default: begin k++; if (k == 18) begin st = 0; ones = 0; k = 0; end end
    endcase
  endfunction
endmodule

// eth_mdio_mmd: one Clause 45 port (45.3), one frame at a time. A port holds up to 32 MMDs (MDIO manageable
// devices); each MMD has its own 16-bit address register, which an address frame sets and data frames use.
//   prtad                      the port address (bench 0); present[d] = 1 for each MMD in the package
//   reset()                    bench registers; every address register is unknown (x) again (45.3: undefined)
//   frame(st, op, pa, dev, d)  one frame; returns {answered, data}: data is the register for a read or a
//                              post-read-increment, the value written for a write, the new address for an address
//                              frame. ST 01 (a Clause 22 frame), another port or a missing MMD: {0, FFFFh}
//   OP: 00 address, 01 write, 11 read, 10 post-read-increment (stops at 65535)
//   Registers (bench values): m.5 devices in package; 1.0 and 3.0 control 1 (2040h); 1.1 and 3.1 status 1 (bit 2:
//   receive link, latching low); 3.32 BASE-R status 1 (1001h: link up, block lock); 3.33 BASE-R status 2 (bit 15
//   latched block lock; bits 7:0 errored blocks, cleared when read); 7.0 AN control (1000h); address 65535 of each
//   MMD holds FFF0h + d. Other addresses read 0000h; writes to addresses above 63 other than 65535 are dropped.
module eth_mdio_mmd;
  bit [4:0] prtad = 5'd0;
  bit present [0:31];
  logic [15:0] areg [0:31];
  bit [15:0] mem [0:2047];          // MMD d, address a (a < 64): mem[64 * d + a]
  bit [15:0] top [0:31];            // address 65535
  bit link = 1, link_lat1 = 1, link_lat3 = 1;
  bit [7:0] errs = 8'd5;
  function automatic void reset();
    for (int d = 0; d < 32; d++) begin present[d] = 0; areg[d] = 16'hxxxx; top[d] = 16'hfff0 + d; end
    for (int i = 0; i < 2048; i++) mem[i] = 16'h0000;
    present[1] = 1; present[3] = 1; present[7] = 1;
    for (int d = 0; d < 32; d++) if (present[d]) mem[64 * d + 5] = 16'h008a;   // MMDs 1, 3 and 7 in this package
    mem[64 + 0] = 16'h2040; mem[192 + 0] = 16'h2040; mem[192 + 32] = 16'h1001; mem[448 + 0] = 16'h1000;
    link = 1; link_lat1 = 1; link_lat3 = 1; errs = 8'd5;
  endfunction
  function automatic void set_link(input bit up); link = up; if (!up) begin link_lat1 = 0; link_lat3 = 0; end endfunction
  function automatic [15:0] get(input int d, input [15:0] a);
    reg [15:0] v;
    if (a == 16'hffff) return top[d];
    if (a > 63) return 16'h0000;
    v = mem[64 * d + a];
    if (d == 1 && a == 1) begin v = {13'd0, link_lat1, 2'b00}; link_lat1 = link; end
    if (d == 3 && a == 1) begin v = {13'd0, link_lat3, 2'b00}; link_lat3 = link; end
    if (d == 3 && a == 33) begin v = {link, 7'd0, errs}; errs = 8'd0; end
    return v;
  endfunction
  function automatic logic [16:0] frame(input [1:0] st, input [1:0] op, input [4:0] pa, input [4:0] dev, input [15:0] d);
    logic [15:0] a, v;
    if (st != 2'b00 || pa != prtad || !present[dev]) return {1'b0, 16'hffff};
    a = areg[dev];
    case (op)
      2'b00: begin areg[dev] = d; return {1'b1, d}; end
      2'b01: begin
               if (a === 16'hffff) top[dev] = d;
               else if (a < 64 && !(dev == 3 && (a == 1 || a == 32 || a == 33)) && !(dev == 1 && a == 1)) mem[64 * dev + a] = d;
               return {1'b1, d};
             end
      2'b11: begin if ($isunknown(a)) return {1'b1, 16'hxxxx}; return {1'b1, get(dev, a)}; end
      default: begin
               if ($isunknown(a)) return {1'b1, 16'hxxxx};
               v = get(dev, a);
               if (a != 16'hffff) areg[dev] = a + 16'd1;
               return {1'b1, v};
             end
    endcase
  endfunction
endmodule
ConceptWhich value of ST starts a Clause 22 frame?
ConceptWhat is the shortest MDC period a PHY must accept?
ConceptWho drives the second turnaround bit of a write?
ConceptThe link dropped for 1 ms and came back. What does the first read of bit 1.2 return?

Common Mistakes

Wrong Keep driving MDIO through the turnaround of a read.

The PHY drives 0 in the second bit: two drivers fight.

Fix Let go from the first turnaround bit to the end of the data.

Wrong Trust FFFFh from a read.

An absent PHY also reads as all ones.

Fix Check that the second turnaround bit was 0.

Wrong Read link status once and act on it.

Bit 1.2 latches low: the first read reports a past drop.

Fix Read register 1 twice when you need the current state.

Wrong Skip the preamble for every PHY.

Only a PHY that sets bit 1.6 accepts frames without it.

Fix Send 32 ones unless every PHY on the bus reports 1.6.

Remember

  • MDIO: MDC from the STA, one shared data line with a pull-up, up to 32 PHYs.
  • Frame: 32 ones, ST 01, OP, PHYAD, REGAD, TA, 16 data bits; MSB first.
  • In a read the STA lets go at the turnaround; a PHY drives 0, then the data.
  • Register 0 controls, register 1 reports; link status latches low.

Practice

Report a problem with this page