Link Fault Signalling

Cut one direction of a link and follow the fault messages. Local Fault comes from the PHY, Remote Fault goes back, then Idle until the wire heals.

You Will Be Able To

  • Read Local Fault, Remote Fault and Link Interruption ordered sets on the lanes.
  • Trace how a one-way break is reported to the far end.
  • Apply the four-sequence and 128-column rules of the state machine.
  • Say what the RS sends for each value of link_fault.
Lesson
P11.19
Time
30 min
Runs on
Your browser
Check
5 questions

Ethernet links run in two directions. When one breaks, the sender would keep transmitting into nothing. Link fault signalling tells it to stop.

ColumnA seesA sendsB seesB sends
103OKdataLocal FaultRemote Fault
116Remote FaultIdleLocal FaultRemote Fault
627Remote FaultIdleOKdata
764OKdataOKdata

Bench run with a private RS model: wire delay 10 columns each way; A to B cut from column 100 to 500. Each row is a change of link_fault.

Messages in the Gap

Faults travel as Sequence ordered sets: the Sequence character on lane 0, then three data octets (46.3.4). They take the place of idle between packets.

ColumnLane 0Lane 1Lane 2Lane 3Meaning
0IIIIidle
1Q000001Local Fault
2Q000002Remote Fault
3Q000003Link Interruption
4Q000000reserved
5IIIIidle

Bench run of the example. Q is the Sequence control character (9Ch) on lane 0; lanes 1 to 3 are data. IEEE Std 802.3-2022 Table 46-5.

A PHY sublayer that sees its link become unreliable sends Local Fault up to its RS. An RS that receives Local Fault answers with Remote Fault. A PHY may also report Link Interruption for a link that may be temporarily interrupted (46.3.4).

One Broken Direction

Who Says What When One Direction BreaksThe wire from A to B is cut. B's PHY reports Local Fault to B's RS. B tells A with Remote Fault. A stops sending frames.
  • I/O
  • Channel / handshake
  • Data
  • Control
Who says what when one direction breaksThe wire from A to B is cut. B's PHY reports Local Fault to B's RS. B tells A with Remote Fault. A stops sending frames. io Station A (RS) receives RemoteFault, sends Idle channel A to B: cut nothing arrives io B's PHY detects the loss,sends Local Fault up io Station B (RS) receives Local Fault,sends Remote Fault channel B to A: still works carries Remote Fault Local FaultRemote Fault
  1. io Station A (RS)receives Remote Fault, sends Idle
    • A to B: cut
  2. channel A to B: cutnothing arrives
    • B's PHY
  3. io B's PHYdetects the loss, sends Local Fault up
    • Local Fault → Station B (RS)
  4. io Station B (RS)receives Local Fault, sends Remote Fault
    • Remote Fault → B to A: still works
  5. channel B to A: still workscarries Remote Fault
    • Station A (RS)
  1. Cut

    The A to B wire breaks. B's PHY loses its signal.

  2. Local Fault

    B's PHY puts Local Fault ordered sets on its receive path to B's RS.

  3. Remote Fault

    B's RS sends Remote Fault ordered sets to A, over the direction that still works.

  4. Idle

    A's RS receives Remote Fault and sends Idle instead of frames.

Read the diagram as text
  • Station A (RS): receives Remote Fault, sends Idle
  • A to B: cut: nothing arrives
  • B's PHY: detects the loss, sends Local Fault up
  • Station B (RS): receives Local Fault, sends Remote Fault
  • B to A: still works: carries Remote Fault
  • Station A (RS) → A to B: cut
  • A to B: cut → B's PHY
  • B's PHY → Station B (RS): Local Fault
  • Station B (RS) → B to A: still works: Remote Fault
  • B to A: still works → Station A (RS)

IEEE Std 802.3-2022 46.3.4. Only an RS sends Remote Fault; a PHY sends Local Fault and Link Interruption.

In the bench run, B decided Local Fault at column 103, after four of them. A decided Remote Fault 13 columns later. That is ten columns of wire, then three more for sets 2 to 4.

A sent 16 columns of frames into the dead link before it stopped.

When the wire healed at column 500, B waited 128 quiet columns and resumed. Then A, seeing no more Remote Fault, waited 128 more.

Counting Before Acting

One stray ordered set must not take a link down. So the RS acts only on a steady stream of them (46.3.4.3).

The Link Fault State MachineINIT, COUNT and FAULT. Four fault sequences of one type, each less than 128 columns apart, set link_fault. 128 quiet columns clear it.
  • Control / FSM
  • Control
The link fault state machineINIT, COUNT and FAULT. Four fault sequences of one type, each less than 128 columns apart, set link_fault. 128 quiet columns clear it. control INIT link_fault = OK,seq_cnt = 0 control COUNT seq_cnt + 1, col_cnt =0, remember the type control FAULT link_fault = type,col_cnt = 0; the sametype again stays hereand resets col_cnt control NEW_FAULT_TYPE seq_cnt = 0, thenCOUNT fault sequence4th of one typeother typeother type128 quiet columns128 quiet columns
  1. control INITlink_fault = OK, seq_cnt = 0
    • fault sequence → COUNT
  2. control COUNTseq_cnt + 1, col_cnt = 0, remember the type
    • 4th of one type → FAULT
    • other type → NEW_FAULT_TYPE
    • 128 quiet columns → INIT
  3. control FAULTlink_fault = type, col_cnt = 0; the same type again stays here and resets col_cnt
    • other type → NEW_FAULT_TYPE
    • 128 quiet columns → INIT
  4. control NEW_FAULT_TYPEseq_cnt = 0, then COUNT
    • COUNT
  1. First sequence

    A fault sequence moves INIT to COUNT, with a count of 1.

  2. Fourth

    The 4th of the same type, each less than 128 columns after the last, enters FAULT.

  3. Other type

    A sequence of another type restarts the count. link_fault keeps its value meanwhile.

  4. Quiet

    128 columns without a fault sequence go back to INIT, so link_fault is OK. COUNT also returns to INIT this way.

Read the diagram as text
  • INIT: link_fault = OK, seq_cnt = 0
  • COUNT: seq_cnt + 1, col_cnt = 0, remember the type
  • FAULT: link_fault = type, col_cnt = 0; the same type again stays here and resets col_cnt
  • NEW_FAULT_TYPE: seq_cnt = 0, then COUNT
  • INIT → COUNT: fault sequence
  • COUNT → FAULT: 4th of one type
  • COUNT → NEW_FAULT_TYPE: other type
  • FAULT → NEW_FAULT_TYPE: other type
  • NEW_FAULT_TYPE → COUNT
  • FAULT → INIT: 128 quiet columns
  • COUNT → INIT: 128 quiet columns

After IEEE Std 802.3-2022 Figure 46-11 (redrawn; same states and conditions).

What the RS receivedlink_fault after it
3 Local Fault sets in a rowOK
4 Local Fault sets in a rowLocal Fault
4 sets, 127 idle columns after eachLocal Fault
4 sets, 128 idle columns after eachOK
fault, then 127 idle columnsLocal Fault
one more idle column (128)OK
4 Local Fault sets, then 3 Remote Fault setsLocal Fault
a 4th Remote Fault setRemote Fault
4 sets of type 00h, 4 of type 04h (reserved)OK
4 Sequence characters on lane 2OK

Bench runs of one RS (private model). The counter counts each column without a fault sequence; the 128th clears link_fault. That order is the bench's reading of Figure 46-11.

Reserved types, a Sequence on another lane, or nonzero lanes 1 and 2 are not fault sequences. They count as quiet columns.

What the RS Sends

link_faultWhat the RS sends
OKMAC frames as asked; Idle between them
Local FaultRemote Fault ordered sets, without a break
Remote FaultIdle, without a break
Link InterruptionIdle, without a break

IEEE Std 802.3-2022 46.3.4.3, items a) to c). A frame in progress may be cut short.

Twin no_remote_fault: B's RS sends Idle on Local Fault, not Remote Fault. A never hears about the break.

With the twin, A sent frames for 400 of the 400 columns of the outage. With the clean RS, 16.

On the 64-bit interfaces the same sets are eight octets: lanes 4 to 7 carry 00h (81.3.4). There one 8-lane transfer is one column (81.3.4).

Try It

The bench writes four Sequence ordered sets into eth_rs, one per column, and prints the columns.

eth_xgmii_mon counts every column with a Sequence character on lane 0, of any type.

Change the last ordered set's lane 3 from 8'h00 to 8'h04. It is still a Sequence column, but no fault type.

RUNIcarus Verilog · in your browser
Edit the code, then run it
Expected: column 0: I I I I control flags, lane 0 first: 1111 column 1: Q 00 00 01 control flags, lane 0 first: 1000 column 2: Q 00 00 02 control flags, lane 0 first: 1000 column 3: Q 00 00 03 control flags, lane 0 first: 1000 column 4: Q 00 00 00 control flags, lane 0 first: 1000 column 5: I I I I control flags, lane 0 first: 1111 monitor: 4 columns hold a Sequence ordered set
Read included file: hs_pkg.sv
`timescale 1ns/1ns
// hs_pkg.sv: shared pure functions, and the bench random generator (read-only).
package hs_pkg;
  // xorshift32 (Marsaglia 2003): a linear generator over GF(2), period 2^32 - 1. A zero state is
  // replaced by 1, because zero maps to itself.
  function automatic [31:0] xs32(input [31:0] s);
    reg [31:0] x;
    x = (s == 32'd0) ? 32'd1 : s;
    x = x ^ (x << 13); x = x ^ (x >> 17); x = x ^ (x << 5);
    return x;
  endfunction
  // A Fibonacci PRBS generator x^n + x^m + 1 (PRBS7: 7,6; PRBS9: 9,5; PRBS15: 15,14; PRBS23: 23,18;
  // PRBS31: 31,28). The output bit is s[n-1]; the next state shifts the feedback into bit 0.
  function automatic [31:0] prbs_next(input [31:0] s, input int n, input int m);
    reg fb;
    fb = s[n-1] ^ s[m-1];
    return ((s << 1) | {31'd0, fb}) & ((n == 32) ? 32'hffffffff : ((32'd1 << n) - 32'd1));
  endfunction
  function automatic int ones(input [63:0] v);
    int n; n = 0;
    for (int i = 0; i < 64; i++) n += v[i];
    return n;
  endfunction
  // GF(16) with x^4 + x + 1, and GF(1024) with x^10 + x^3 + 1: shift-and-add multiply, no tables.
  function automatic [3:0] gf16_mul(input [3:0] a, input [3:0] b);
    reg [3:0] p, x; p = 4'd0; x = a;
    for (int i = 0; i < 4; i++) begin
      if (b[i]) p = p ^ x;
      x = x[3] ? ({x[2:0], 1'b0} ^ 4'b0011) : {x[2:0], 1'b0};
    end
    return p;
  endfunction
  function automatic [3:0] gf16_pow(input int e);   // alpha^e, alpha = x
    reg [3:0] p; int k; p = 4'd1; k = e % 15; if (k < 0) k += 15;
    for (int i = 0; i < k; i++) p = gf16_mul(p, 4'd2);
    return p;
  endfunction
  function automatic int gf16_log(input [3:0] a);   // -1 for 0
    reg [3:0] p; p = 4'd1;
    if (a == 4'd0) return -1;
    for (int i = 0; i < 15; i++) begin if (p == a) return i; p = gf16_mul(p, 4'd2); end
    return -1;
  endfunction
  function automatic [9:0] gf1024_mul(input [9:0] a, input [9:0] b);
    reg [9:0] p, x; p = 10'd0; x = a;
    for (int i = 0; i < 10; i++) begin
      if (b[i]) p = p ^ x;
      x = x[9] ? ({x[8:0], 1'b0} ^ 10'b0000001001) : {x[8:0], 1'b0};
    end
    return p;
  endfunction
  function automatic [9:0] gf1024_pow(input int e);
    reg [9:0] p; int k; p = 10'd1; k = e % 1023; if (k < 0) k += 1023;
    for (int i = 0; i < k; i++) p = gf1024_mul(p, 10'd2);
    return p;
  endfunction
endpackage

// hs_rng: the bench's random numbers. Same seed, same numbers, on every engine.
module hs_rng;
  int unsigned s = 32'h2545f491;
  function automatic void seed(input int unsigned v); s = (v == 0) ? 32'd1 : v; endfunction
  function automatic int unsigned next(); s = hs_pkg::xs32(s); return s; endfunction
  function automatic int below(input int n); s = hs_pkg::xs32(s); return (n <= 0) ? 0 : int'(s % n); endfunction
  function automatic bit bit1(); s = hs_pkg::xs32(s); return s[16]; endfunction
  function automatic bit chance_ppm(input int ppm); s = hs_pkg::xs32(s); return (s % 1000000) < ppm; endfunction
  function automatic [7:0] byte8(); s = hs_pkg::xs32(s); return s[23:16]; endfunction
endmodule
Read included file: hs_code.sv
`timescale 1ns/1ns
// hs_code.sv: line codes, CRCs and scramblers (read-only).

// ---------------------------------------------------------------------------------------------
// hs_8b10b: 8b/10b encoder and decoder with running disparity and the 12 K codes.
// code[9:0] = {a,b,c,d,e,i,f,g,h,j}; bit a (code[9]) goes on the wire first. rd: 0 = RD-, 1 = RD+.
//   encode(d, k, rd_in) -> {rd_out, code[9:0]}            (11 bits)
//   decode(code, rd_in) -> {rd_out, disp_err, code_err, k, d[7:0]}   (12 bits)
//   enc(d, k) / dec(code): the same, with the running disparity kept in rd_tx / rd_rx
// A K request for a byte that is not one of the 12 K codes is encoded as data and counted in bad_k.
// Decoder: code_err = the code is in neither column of the table; disp_err = it is a valid code
// only in the other column. rd_out follows the sub-block rule on the received bits.
// Faults: no_rd (always the RD- column), a7_never (never the alternate D.x.A7),
//         keep_rd_on_unbalanced (the 4b sub-block is chosen with the disparity from before the 6b one),
//         no_balanced_flip (D.07 and D.x.3 keep their RD- form at RD+), dec_no_disp_check.
module hs_8b10b;
  bit no_rd = 0, a7_never = 0, keep_rd_on_unbalanced = 0, no_balanced_flip = 0, dec_no_disp_check = 0;
  bit trace = 0;
  bit rd_tx = 0, rd_rx = 0;
  int bad_k = 0, symbols = 0, code_errs = 0, disp_errs = 0;
  bit last_k = 0, last_code_err = 0, last_disp_err = 0;
  bit valid_m [0:1023]; bit valid_p [0:1023]; bit [8:0] kd [0:1023]; bit built = 0;
  function automatic [5:0] t6(input [4:0] x);   // 5b/6b, RD- column, abcdei
    case (x)
      5'd0: return 6'b100111;  5'd1: return 6'b011101;  5'd2: return 6'b101101;  5'd3: return 6'b110001;
      5'd4: return 6'b110101;  5'd5: return 6'b101001;  5'd6: return 6'b011001;  5'd7: return 6'b111000;
      5'd8: return 6'b111001;  5'd9: return 6'b100101;  5'd10: return 6'b010101; 5'd11: return 6'b110100;
      5'd12: return 6'b001101; 5'd13: return 6'b101100; 5'd14: return 6'b011100; 5'd15: return 6'b010111;
      5'd16: return 6'b011011; 5'd17: return 6'b100011; 5'd18: return 6'b010011; 5'd19: return 6'b110010;
      5'd20: return 6'b001011; 5'd21: return 6'b101010; 5'd22: return 6'b011010; 5'd23: return 6'b111010;
      5'd24: return 6'b110011; 5'd25: return 6'b100110; 5'd26: return 6'b010110; 5'd27: return 6'b110110;
      5'd28: return 6'b001110; 5'd29: return 6'b101110; 5'd30: return 6'b011110; default: return 6'b101011;
    endcase
  endfunction
  function automatic [3:0] t4d(input [2:0] y);  // 3b/4b data, RD- column, fghj (y = 7 is P7)
    case (y)
      3'd0: return 4'b1011; 3'd1: return 4'b1001; 3'd2: return 4'b0101; 3'd3: return 4'b1100;
      3'd4: return 4'b1101; 3'd5: return 4'b1010; 3'd6: return 4'b0110; default: return 4'b1110;
    endcase
  endfunction
  function automatic [3:0] t4k(input [2:0] y);  // 3b/4b for K codes, RD- form before the flip
    case (y)
      3'd0: return 4'b1011; 3'd1: return 4'b0110; 3'd2: return 4'b1010; 3'd3: return 4'b1100;
      3'd4: return 4'b1101; 3'd5: return 4'b0101; 3'd6: return 4'b1001; default: return 4'b0111;
    endcase
  endfunction
  function automatic bit k_ok(input [7:0] d);
    return d[4:0] == 5'd28 || d == 8'hf7 || d == 8'hfb || d == 8'hfd || d == 8'hfe;
  endfunction
  function automatic int n6(input [5:0] v); return v[0] + v[1] + v[2] + v[3] + v[4] + v[5]; endfunction
  function automatic int n4(input [3:0] v); return v[0] + v[1] + v[2] + v[3]; endfunction
  // running disparity at the end of a sub-block (more ones: +; more zeros: -; 000111 and 0011: +; 111000 and 1100: -)
  function automatic bit rd6(input [5:0] v, input bit rd);
    return (n6(v) > 3) ? 1'b1 : (n6(v) < 3) ? 1'b0 : (v == 6'b000111) ? 1'b1 : (v == 6'b111000) ? 1'b0 : rd;
  endfunction
  function automatic bit rd4(input [3:0] v, input bit rd);
    return (n4(v) > 2) ? 1'b1 : (n4(v) < 2) ? 1'b0 : (v == 4'b0011) ? 1'b1 : (v == 4'b1100) ? 1'b0 : rd;
  endfunction
  // faults: [0] no_rd [1] a7_never [2] keep_rd_on_unbalanced [3] no_balanced_flip
  function automatic [10:0] core(input [7:0] d, input bit k, input bit rd_in, input [3:0] f);
    reg [5:0] six; reg [3:0] four; reg rd0, r6, rd1, a7, kk; reg [4:0] x; reg [2:0] y; int o6, o4;
    x = d[4:0]; y = d[7:5]; kk = k && k_ok(d); rd0 = f[0] ? 1'b0 : rd_in;
    six = (kk && x == 5'd28) ? 6'b001111 : t6(x); o6 = n6(six);
    if (rd0 && (o6 != 3 || (six == 6'b111000 && !f[3]))) begin six = ~six; o6 = 6 - o6; end
    r6 = (o6 > 3) ? 1'b1 : (o6 < 3) ? 1'b0 : (six == 6'b000111) ? 1'b1 : (six == 6'b111000) ? 1'b0 : rd0;
    rd1 = f[2] ? rd0 : r6;
    if (kk) begin
      four = t4k(y); if (rd1) four = ~four;
    end else begin
      a7 = (y == 3'd7) && !f[1] && ((!rd1 && (x == 5'd17 || x == 5'd18 || x == 5'd20)) || (rd1 && (x == 5'd11 || x == 5'd13 || x == 5'd14)));
      four = a7 ? 4'b0111 : t4d(y);
      if (rd1 && (n4(four) != 2 || (four == 4'b1100 && !f[3]))) four = ~four;
    end
    o4 = n4(four);
    return {(o4 > 2) ? 1'b1 : (o4 < 2) ? 1'b0 : (four == 4'b0011) ? 1'b1 : (four == 4'b1100) ? 1'b0 : r6, six, four};
  endfunction
  function automatic [10:0] encode(input [7:0] d, input bit k, input bit rd_in);
    if (k && !k_ok(d)) bad_k++;
    return core(d, k, rd_in, {no_balanced_flip, keep_rd_on_unbalanced, a7_never, no_rd});
  endfunction
  function automatic void build();
    reg [10:0] c;
    for (int i = 0; i < 1024; i++) begin valid_m[i] = 0; valid_p[i] = 0; kd[i] = 9'd0; end
    for (int i = 0; i < 268; i++) begin
      reg [7:0] d; reg k;
      if (i < 256) begin d = i[7:0]; k = 0; end
      else begin k = 1; d = (i < 264) ? {3'(i - 256), 5'd28} : (i == 264) ? 8'hf7 : (i == 265) ? 8'hfb : (i == 266) ? 8'hfd : 8'hfe; end
      c = core(d, k, 1'b0, 4'd0); valid_m[c[9:0]] = 1; kd[c[9:0]] = {k, d};
      c = core(d, k, 1'b1, 4'd0); valid_p[c[9:0]] = 1; kd[c[9:0]] = {k, d};
    end
    built = 1;
  endfunction
  function automatic [11:0] decode(input [9:0] code, input bit rd_in);
    reg here, there, ce, de, r;
    if (!built) build();
    here = rd_in ? valid_p[code] : valid_m[code];
    there = rd_in ? valid_m[code] : valid_p[code];
    ce = !(here || there); de = !ce && !here && !dec_no_disp_check;
    r = rd4(code[3:0], rd6(code[9:4], rd_in));
    return {r, de, ce, ce ? 9'd0 : kd[code]};
  endfunction
  function automatic [9:0] enc(input [7:0] d, input bit k);
    reg [10:0] r; r = encode(d, k, rd_tx); rd_tx = r[10];
    if (trace) $display("s%0d TX %s%0d.%0d code=%b rd=%s", symbols, (k && k_ok(d)) ? "K" : "D", d[4:0], d[7:5], r[9:0], r[10] ? "+" : "-");
    symbols++;
    return r[9:0];
  endfunction
  function automatic [8:0] dec(input [9:0] code);
    reg [11:0] r; r = decode(code, rd_rx); rd_rx = r[11];
    last_disp_err = r[10]; last_code_err = r[9]; last_k = r[8];
    if (r[9]) code_errs++; if (r[10]) disp_errs++;
    if (trace && (r[9] || r[10])) $display("RX %b %s", code, r[9] ? "code error" : "disparity error");
    return r[8:0];
  endfunction
  function automatic bit comma7(input [6:0] w); return w == 7'b0011111 || w == 7'b1100000; endfunction
endmodule

// ---------------------------------------------------------------------------------------------
// hs_crc: a CRC of 1 to 32 bits with any polynomial, seed, bit order and final inversion.
// The register shifts left; the polynomial omits the x^width term. The field is sent register bit
// width-1 first (USB 2.0, USB 3.2 and Ethernet all send it this way).
//   use_crc32(), use_crc16_usb2(), use_crc5_usb2(), use_crc16_usb3(): parameter sets
//   reset(), crc_bit(b), crc_byte(v), crc_bits(v, n), field(), field_bit(i), check_value(), crc_residue_ok()
// Faults: msb_first (bytes enter MSB first), no_invert (the field is not complemented), seed_zero.
module hs_crc;
  int width = 32;
  bit [31:0] poly = 32'h04c11db7, seed = 32'hffffffff, residue = 32'hc704dd7b;
  bit lsb_first = 1, invert = 1;
  bit msb_first = 0, no_invert = 0, seed_zero = 0;
  bit [31:0] r = 32'hffffffff;
  function automatic [31:0] mask(); return (width >= 32) ? 32'hffffffff : ((32'd1 << width) - 32'd1); endfunction
  function automatic void reset(); r = seed_zero ? 32'd0 : (seed & mask()); endfunction
  function automatic void set(input int w, input [31:0] p, input [31:0] s, input [31:0] res, input bit lsb, input bit inv);
    width = w; poly = p; seed = s; residue = res; lsb_first = lsb; invert = inv; reset();
  endfunction
  function automatic void use_crc32();      set(32, 32'h04c11db7, 32'hffffffff, 32'hc704dd7b, 1, 1); endfunction
  function automatic void use_crc16_usb2(); set(16, 32'h8005, 32'hffff, 32'h800d, 1, 1); endfunction
  function automatic void use_crc5_usb2();  set(5, 32'h05, 32'h1f, 32'h0c, 1, 1); endfunction
  function automatic void use_crc16_usb3(); set(16, 32'h100b, 32'hffff, 32'hf6aa, 1, 1); endfunction
  function automatic void crc_bit(input bit b);
    reg fb; fb = b ^ r[width - 1];
    r = ((r << 1) ^ (fb ? poly : 32'd0)) & mask();
  endfunction
  function automatic void crc_byte(input [7:0] v);
    for (int i = 0; i < 8; i++) crc_bit(v[(lsb_first ^ msb_first) ? i : 7 - i]);
  endfunction
  function automatic void crc_bits(input [31:0] v, input int n);   // n bits of v, bit 0 first
    for (int i = 0; i < n; i++) crc_bit(v[i]);
  endfunction
  function automatic [31:0] field(); return (invert && !no_invert) ? (~r & mask()) : r; endfunction
  function automatic bit field_bit(input int i); reg [31:0] f; f = field(); return f[width - 1 - i]; endfunction
  // the usual published "check" number: the field with its first-sent bit read as bit 0
  function automatic [31:0] check_value();
    reg [31:0] f, o; f = field(); o = 32'd0;
    for (int i = 0; i < width; i++) o[i] = f[width - 1 - i];
    return lsb_first ? o : f;
  endfunction
  function automatic bit crc_residue_ok(); return r == (residue & mask()); endfunction
endmodule

// ---------------------------------------------------------------------------------------------
// hs_scr: additive (frame-synchronous) and multiplicative (self-synchronising) scramblers.
// poly holds the coefficients: bit k is x^k; the +1 term is always used (taps() sets bit 0); len is the degree.
// Additive: a Galois LFSR. The key bit is s[len-1]; each step shifts left and adds the low terms of
//   the polynomial when the key bit is 1. The data never enters the register.
// Multiplicative: the line bit is the data bit XOR the register bits at the polynomial's terms;
//   the scrambler shifts its own output in, the descrambler shifts the received line bit in.
//   scr_add(len, poly, seed), scr_mul(len, poly), use_usb3_gen1(), use_x58(), use_x23_usb3() (see its note)
//   scr_bit(b), dscr_bit(b), scr_byte(v), dscr_byte(v) (bit 0 first), scr_reset(), scr_hold() (a skip
//   symbol: no step), scr_unscrambled() (a symbol sent in the clear: 8 steps, data untouched)
// Faults: advance_on_skip (scr_hold steps the LFSR 8 times), no_reset (scr_reset does nothing),
//         wrong_tap (the lowest term x^k becomes x^(k+1)), seed_zero (scr_reset loads 0).
module hs_scr;
  bit mult = 0; int len = 16;
  bit [63:0] poly = 64'h10039, seed = 64'hffff;
  bit advance_on_skip = 0, no_reset = 0, wrong_tap = 0, seed_zero = 0;
  bit [63:0] s = 64'hffff;
  int steps = 0;
  function automatic [63:0] lmask(); return (len >= 64) ? 64'hffffffffffffffff : ((64'd1 << len) - 64'd1); endfunction
  function automatic [63:0] taps();
    reg [63:0] p; int k; p = poly | 64'd1; k = 1;
    if (wrong_tap) begin
      while (k < len && !p[k]) k++;
      if (k < len) begin p[k] = 1'b0; p[k + 1] = 1'b1; end
    end
    return p;
  endfunction
  function automatic void load(); s = (seed_zero ? 64'd0 : seed) & lmask(); endfunction
  function automatic void scr_add(input int n, input [63:0] p, input [63:0] sd); mult = 0; len = n; poly = p; seed = sd; s = sd & lmask(); endfunction
  function automatic void scr_mul(input int n, input [63:0] p); mult = 1; len = n; poly = p; seed = 64'd0; s = 64'd0; endfunction
  function automatic void use_usb3_gen1(); scr_add(16, 64'h10039, 64'hffff); endfunction   // x^16 + x^5 + x^4 + x^3 + 1, seed FFFFh
  function automatic void use_x58(); scr_mul(58, (64'd1 << 58) | (64'd1 << 39) | 64'd1); endfunction   // x^58 + x^39 + 1
  // USB 3.2 Gen 2 (§6.3.2.3) polynomial x^23 + x^21 + x^16 + x^8 + x^5 + x^2 + 1 with seed 1DBFBCh. Only the
  // polynomial and seed are the specification's: the register form here is this library's Galois form, and
  // the reset and bypass rules of §6.3.2.3 are not modelled, so do not quote its key stream as USB's.
  function automatic void use_x23_usb3(); scr_add(23, (64'd1 << 23) | (64'd1 << 21) | (64'd1 << 16) | (64'd1 << 8) | (64'd1 << 5) | (64'd1 << 2) | 64'd1, 64'h1dbfbc); endfunction
  function automatic void scr_reset(); if (!no_reset) load(); endfunction
  function automatic bit key(); return s[len - 1]; endfunction
  function automatic void step();
    reg kb; kb = s[len - 1];
    s = ((s << 1) & lmask()) ^ (kb ? (taps() & lmask()) : 64'd0);
    steps++;
  endfunction
  // the XOR of the register bits at the polynomial's terms x^1..x^len (bit k-1 of the register for x^k)
  function automatic bit fbx(input [63:0] st); return ^(st & (taps() >> 1) & lmask()); endfunction
  function automatic bit scr_bit(input bit b);
    reg o;
    if (!mult) begin o = b ^ s[len - 1]; step(); end
    else begin o = b ^ fbx(s); s = ((s << 1) | {63'd0, o}) & lmask(); steps++; end
    return o;
  endfunction
  function automatic bit dscr_bit(input bit b);
    reg o;
    if (!mult) begin o = b ^ s[len - 1]; step(); end
    else begin o = b ^ fbx(s); s = ((s << 1) | {63'd0, b}) & lmask(); steps++; end
    return o;
  endfunction
  function automatic [7:0] scr_byte(input [7:0] v);
    reg [7:0] o; for (int i = 0; i < 8; i++) o[i] = scr_bit(v[i]); return o;
  endfunction
  function automatic [7:0] dscr_byte(input [7:0] v);
    reg [7:0] o; for (int i = 0; i < 8; i++) o[i] = dscr_bit(v[i]); return o;
  endfunction
  // a skip symbol passes unscrambled and the LFSR holds
  function automatic void scr_hold(); if (advance_on_skip && !mult) for (int i = 0; i < 8; i++) step(); endfunction
  // another symbol that is sent unscrambled (a K code other than COM and SKP): the LFSR still steps 8 times
  function automatic void scr_unscrambled(); if (!mult) for (int i = 0; i < 8; i++) step(); endfunction
endmodule
Read included file: eth_mac.sv
`timescale 1ns/1ns
// eth_frame: one MAC frame as octets, its packet as wire bits, and a bit-serial receiver.
//   pay[i]                         client data, set by the bench before build()
//   build(da, sa, lt, len)         destination, source, Length/Type, len data octets, then the FCS -> oct[0..n-1].
//                                  It adds no pad: give it 46 data octets or more. (Padding is P11.2.1's task; the
//                                  pages show the padding MAC's frames as measured tables.)
//   wire_bits(), wire_bit(i)       the packet in transmit order: preamble, SFD, frame
//   rx_start(), rx_bit(b), rx_end()  hunt for the SFD, collect octets, then parse()
//   parse()                        da, sa, lt, is_length, is_type, data_len, fcs_rx, fcs_calc, fcs_ok
// Faults: fcs_msb_first, fcs_no_invert, fcs_covers_preamble, sfd_wrong, msb_first_octets.
module eth_frame;
  localparam int MIN_FRAME = 64, MAX_BASIC = 1518, MAX_QTAG = 1522, MAX_ENVELOPE = 2000;
  bit fcs_msb_first = 0, fcs_no_invert = 0, fcs_covers_preamble = 0, sfd_wrong = 0, msb_first_octets = 0;
  hs_crc crc();
  bit [7:0] pay [0:2047];
  bit [7:0] oct [0:2047];
  int n = 0;
  bit [47:0] da = 0, sa = 0; bit [15:0] lt = 0;
  bit is_length = 0, is_type = 0, fcs_ok = 0;
  int data_len = 0;
  bit [31:0] fcs_rx = 0, fcs_calc = 0;
  // receiver state
  bit in_frame = 0; bit [7:0] hist = 0, cur = 0; int nb = 0, excess = 0, sfd_at = -1, bits_seen = 0;

  // The FCS of oct[0..len-1] as four octets: the first octet sent is in [7:0].
  function automatic [31:0] fcs_of(input int len);
    crc.use_crc32(); crc.msb_first = fcs_msb_first; crc.no_invert = fcs_no_invert; crc.reset();
    if (fcs_covers_preamble) begin
      for (int i = 0; i < 7; i++) crc.crc_byte(8'h55);
      crc.crc_byte(8'hd5);
    end
    for (int i = 0; i < len; i++) crc.crc_byte(oct[i]);
    return crc.check_value();
  endfunction

  function automatic void build(input [47:0] d, input [47:0] s, input [15:0] t, input int len);
    int k; reg [31:0] f;
    k = 0;
    for (int i = 0; i < 6; i++) begin oct[k] = d[47 - 8*i -: 8]; k++; end
    for (int i = 0; i < 6; i++) begin oct[k] = s[47 - 8*i -: 8]; k++; end
    oct[k] = t[15:8]; k++;
    oct[k] = t[7:0]; k++;
    for (int i = 0; i < len; i++) begin oct[k] = pay[i]; k++; end
    f = fcs_of(k);
    for (int i = 0; i < 4; i++) begin oct[k] = f[8*i +: 8]; k++; end
    n = k; excess = 0;
    parse();
  endfunction

  function automatic void parse();
    da = 0; sa = 0; lt = 0; is_length = 0; is_type = 0; fcs_ok = 0; data_len = 0; fcs_rx = 0; fcs_calc = 0;
    if (n >= 14) begin
      da = {oct[0], oct[1], oct[2], oct[3], oct[4], oct[5]};
      sa = {oct[6], oct[7], oct[8], oct[9], oct[10], oct[11]};
      lt = {oct[12], oct[13]};
      is_length = (lt <= 16'd1500);
      is_type = (lt >= 16'd1536);
    end
    if (n >= 18) begin
      fcs_rx = {oct[n-1], oct[n-2], oct[n-3], oct[n-4]};
      fcs_calc = fcs_of(n - 4);
      fcs_ok = (fcs_rx == fcs_calc);
      data_len = is_length ? int'(lt) : n - 18;
    end
  endfunction

  function automatic int wire_bits(); return 8 * (8 + n); endfunction
  function automatic bit wire_bit(input int i);
    int o, b; reg [7:0] v;
    o = i / 8; b = i % 8;
    if (o < 7) v = 8'h55;
    else if (o == 7) v = sfd_wrong ? 8'h55 : 8'hd5;
    else v = oct[o - 8];
    return msb_first_octets ? v[7 - b] : v[b];
  endfunction

  function automatic void rx_start();
    in_frame = 0; hist = 0; cur = 0; nb = 0; n = 0; excess = 0; sfd_at = -1; bits_seen = 0;
  endfunction
  function automatic void rx_bit(input bit b);
    bits_seen++;
    if (!in_frame) begin
      hist = {hist[6:0], b};                      // the oldest bit is hist[7]
      if (hist == 8'b10101011) begin in_frame = 1; sfd_at = bits_seen; end
    end else begin
      if (msb_first_octets) cur[7 - nb] = b; else cur[nb] = b;
      nb++;
      if (nb == 8) begin oct[n] = cur; n++; nb = 0; end
    end
  endfunction
  function automatic void rx_end(); excess = nb; parse(); endfunction
endmodule
// eth_axis: a MAC client bus in the style of AXI4-Stream (IHI 0051B 2.2 handshake, 2.5 TKEEP, 2.6 TLAST, 2.9 TUSER),
// 64 bits wide. Byte 0 of a beat is tdata[7:0] and is first in the frame (AXI4-Stream 2.4.1). Bench conventions,
// not AXI4-Stream's or 802.3's: tkeep is all ones except on the last beat, where it covers bytes 0 to k-1; one tuser
// bit (transfer-based, 2.9.1), read on the last beat only, marks a bad frame (receive) or asks the MAC to abort it
// (transmit).
//   load(n)                  beats for octets oct[0..n-1]: bd[], bk[], bl[], nbeats; bv[] = valid per cycle, ncyc
//   tx_cycles()              the transmit MAC: one beat per cycle once a frame has started. Returns 0 sent,
//                            1 underrun (tvalid fell inside the frame), 2 aborted by tuser. sent_octets, fail_cycle.
// Fault: tvalid_gap (load() leaves cycle 3 of the frame empty: the client was late with a beat).
module eth_axis;
  bit tvalid_gap = 0;
  bit [7:0] oct [0:2047];
  bit [63:0] bd [0:300]; bit [7:0] bk [0:300]; bit bl [0:300]; bit bu [0:300];
  int nbeats = 0;
  bit bv [0:301]; int bix [0:301]; int ncyc = 0;
  int sent_octets = 0, fail_cycle = -1;
  function automatic void load(input int n);
    int b, k;
    nbeats = (n + 7) / 8;
    for (b = 0; b < nbeats; b++) begin
      bd[b] = 64'd0; bk[b] = 8'd0; bl[b] = (b == nbeats - 1); bu[b] = 0;
      for (k = 0; k < 8; k++) if (8*b + k < n) begin bd[b][8*k +: 8] = oct[8*b + k]; bk[b][k] = 1'b1; end
    end
    ncyc = 0;
    for (b = 0; b < nbeats; b++) begin
      if (tvalid_gap && b == 3) begin bv[ncyc] = 0; bix[ncyc] = -1; ncyc++; end
      bv[ncyc] = 1; bix[ncyc] = b; ncyc++;
    end
  endfunction
  function automatic int tx_cycles();
    bit started; started = 0; sent_octets = 0; fail_cycle = -1;
    for (int c = 0; c < ncyc; c++) begin
      if (!bv[c]) begin
        if (started) begin fail_cycle = c; return 1; end
      end else begin
        started = 1;
        if (bl[bix[c]] && bu[bix[c]]) begin fail_cycle = c; return 2; end
        for (int k = 0; k < 8; k++) if (bk[bix[c]][k]) sent_octets++;
      end
    end
    return 0;
  endfunction
endmodule

// eth_pause: the PAUSE function of MAC Control (Annex 31B) at the station that receives PAUSE frames, in octet
// times (one octet time is 8 bit times; a pause quantum is 512 bit times = 64 octet times, 31B.2).
//   reset(), rx_pause(t, q)  a valid PAUSE frame with pause_time q ended at time t: the timer restarts (31B.3.3)
//   may_start(t)             1 when a new data frame may start at time t. A frame already started is never cut
//                            (31B.3.7). react is the bench's reaction time: frames may still start until t + react.
//   paused_until             the time the timer runs out
//   pause_octets(q, o[])     not here: build a PAUSE frame with eth_frame (DA 01-80-C2-00-00-01, 8808h, 0001h, q)
// Faults: pause_ignored, pause_adds_not_overrides (a new frame adds to the timer, and zero does not cancel),
//         slow_reaction (react = 70 quanta, over the 60 allowed at 10 Gb/s), timer_in_bits (q counts bit times).
module eth_pause;
  localparam int QUANTUM = 64;                     // octet times
  bit pause_ignored = 0, pause_adds_not_overrides = 0, slow_reaction = 0, timer_in_bits = 0;
  int react = 0, t_rx = -1, paused_until = 0;
  function automatic void reset(); t_rx = -1; paused_until = 0; endfunction
  function automatic void rx_pause(input int t, input int q);
    int len;
    if (pause_ignored) return;
    len = timer_in_bits ? (q + 7) / 8 : q * QUANTUM;
    if (pause_adds_not_overrides && paused_until > t) paused_until = paused_until + len;
    else paused_until = t + len;
    t_rx = t;
  endfunction
  function automatic bit may_start(input int t);
    int r;
    r = slow_reaction ? 70 * QUANTUM : react;
    if (t_rx < 0) return 1;
    if (t < t_rx + r) return 1;
    return t >= paused_until;
  endfunction
endmodule

// eth_pfc: priority-based flow control (Annex 31D). The frame is 802.3's; holding a priority's queue is the MAC
// Control client's job (IEEE 802.1Q, not held), so the eight timers here are a bench client, in octet times.
//   build(f_oct[], pev, times[])   not here: the bench writes opcode 01-01, the vector and eight times into eth_frame
//   reset(), rx(t, pev, tm[0..7])  for each e[n] = 1 (bit n of the vector's low octet), priority n stops until
//                                  t + 64 * time[n] (hold_end[n]); e[n] = 0 leaves priority n alone; time[n] = 0 releases it
//   blocked(n, t)                  1 while priority n is held
// Fault: pfc_wrong_priority (reads e[n] from bit 7 - n).
module eth_pfc;
  bit pfc_wrong_priority = 0;
  int hold_end [0:7];
  function automatic void reset(); for (int i = 0; i < 8; i++) hold_end[i] = 0; endfunction
  function automatic void rx(input int t, input [15:0] pev, input [127:0] tm);   // tm[16*n +: 16] = time[n]
    bit e;
    for (int n = 0; n < 8; n++) begin
      e = pfc_wrong_priority ? pev[7 - n] : pev[n];
      if (e) hold_end[n] = t + 64 * int'(tm[16*n +: 16]);
    end
  endfunction
  function automatic bit blocked(input int n, input int t); return t < hold_end[n]; endfunction
endmodule

// eth_csma_tx: one half-duplex transmitter (4.2.3.2), one call of tick() per octet time.
//   reset(), load(frame_octets)   a frame of frame_octets (DA to FCS) waits to be sent; it is padded to min_frame
//   tick(carrier)                 carrier: another station's signal is on the wire here now. Returns 1 when the
//                                 station puts an octet (packet or jam) on the wire.
//   plan[i]                       the wait, in slots, after collision i + 1. The bench sets it (default 0). This
//                                 readable station draws nothing and has no attempt limit.
//   state  0 idle, 1 defer, 2 send, 3 jam, 4 backoff, 5 sent (as far as the sender knows)
//   pkt, sent, quiet, left, attempts, late, last_start, last_r
// min_frame is 64 octets; a bench may lower it to show why it is 64. Fault: no_backoff (every wait is 0 slots).
// Deference is a bench simplification: the 12-octet quiet count restarts on any carrier, own or received, and the
// station never starts while carrier is present. 4.2.8 restarts only the first part of the gap, and then transmits
// whatever the carrier.
module eth_csma_tx;
  localparam int SLOT = 64, JAM = 4, GAP = 12, PRE = 8;   // octet times
  bit no_backoff = 0;
  int min_frame = 64;
  int plan [0:63];
  int state = 0, pkt = 0, sent = 0, quiet = GAP, left = 0, attempts = 0, late = 0, last_start = -1, last_r = 0, now = 0;
  function automatic void reset();
    state = 0; pkt = 0; sent = 0; quiet = GAP; left = 0; attempts = 0; late = 0; last_start = -1; last_r = 0; now = 0;
  endfunction
  function automatic void load(input int frame_octets);
    pkt = PRE + frame_octets;
    if (frame_octets < min_frame) pkt = PRE + min_frame;
    state = 1; attempts = 0; sent = 0; late = 0;
  endfunction
  function automatic bit tick(input bit carrier);
    bit on;
    on = 0;
    if (state == 1 && !carrier && quiet >= GAP) begin state = 2; sent = 0; last_start = now; end
    if (state == 2 && carrier) begin
      attempts++; if (sent > SLOT) late++;
      state = 3; left = JAM;
    end
    case (state)
      2: begin sent++; on = 1; if (sent == pkt) state = 5; end
      3: begin
           on = 1; left--;
           if (left == 0) begin
             last_r = no_backoff ? 0 : plan[(attempts - 1) % 64];
             left = SLOT * last_r;
             state = (left == 0) ? 1 : 4;
           end
         end
      4: begin left--; if (left == 0) state = 1; end
      default: ;
    endcase
    quiet = (carrier || on) ? 0 : ((quiet < GAP) ? quiet + 1 : GAP);
    now++;
    return on;
  endfunction
endmodule

// eth_csma: two eth_csma_tx stations, A and B, at the two ends of a wire with a one-way delay of d octet times.
//   run(fa, ready_a, fb, ready_b, tmax)   each station loads its frame (fa, fb octets) at its ready time
//   on_a[t], on_b[t]          what each station put on the wire at time t
//   ev_t[], ev_who[] (0 A, 1 B), ev_kind[], ev_v[], n_ev   the event log:
//     kind 0 starts attempt v; 1 sees a collision after v octets; 2 jam over, backs off v slots;
//     3 last octet sent (v = octets); 4 gives up after v attempts
//   delivered(i)              1 when station i's last attempt reached the far end with no overlap there
//   a.plan[], b.plan[], a.no_backoff, b.no_backoff, a.min_frame, b.min_frame: the stations' settings
module eth_csma;
  eth_csma_tx a(); eth_csma_tx b();
  int d = 10, n_ev = 0, tend = 0;
  bit on_a [0:16383]; bit on_b [0:16383];
  int ev_t [0:255]; int ev_who [0:255]; int ev_kind [0:255]; int ev_v [0:255];
  function automatic void log_ev(input int t, input int who, input int kind, input int v);
    if (n_ev < 256) begin ev_t[n_ev] = t; ev_who[n_ev] = who; ev_kind[n_ev] = kind; ev_v[n_ev] = v; n_ev++; end
  endfunction
  function automatic void note(input int t, input int who, input int s0, input int s1, input int sent0, input int att, input int r, input int sent1);
    if (s0 != 2 && s1 == 2) log_ev(t, who, 0, att + 1);
    if (s0 == 2 && (s1 == 3 || s1 == 4)) log_ev(t, who, 1, sent0);
    if (s0 == 3 && (s1 == 4 || s1 == 1)) log_ev(t, who, 2, r);
    if (s0 != 5 && s1 == 5) log_ev(t, who, 3, sent1);
    if (s0 != 6 && s1 == 6) log_ev(t, who, 4, att);
  endfunction
  function automatic void run(input int fa, input int ready_a, input int fb, input int ready_b, input int tmax);
    bit ca, cb; int sa, sb, xa, xb;
    a.reset(); b.reset(); n_ev = 0; tend = tmax;
    for (int t = 0; t < tmax; t++) begin
      if (t == ready_a) a.load(fa);
      if (t == ready_b) b.load(fb);
      ca = (t >= d) ? on_b[t - d] : 1'b0;
      cb = (t >= d) ? on_a[t - d] : 1'b0;
      sa = a.state; sb = b.state; xa = a.sent; xb = b.sent;
      on_a[t] = a.tick(ca);
      on_b[t] = b.tick(cb);
      note(t, 0, sa, a.state, xa, a.attempts, a.last_r, a.sent);
      note(t, 1, sb, b.state, xb, b.attempts, b.last_r, b.sent);
    end
  endfunction
  function automatic bit delivered(input int i);
    int s, p, u;
    if (i == 0 && a.state != 5) return 0;
    if (i == 1 && b.state != 5) return 0;
    s = (i == 0) ? a.last_start : b.last_start;
    p = (i == 0) ? a.pkt : b.pkt;
    for (int t = s; t < s + p; t++) begin
      u = t + d;
      if (u < tend && ((i == 0) ? on_b[u] : on_a[u])) return 0;
    end
    return 1;
  endfunction
endmodule

// eth_gap: how long the gap before the next Start is on a 4-lane XGMII, where Start must sit on lane 0
// (46.3.1.4). A gap counts every character from the Terminate to the last idle before Start. A packet is
// 8 + n characters (Start, six preamble octets, SFD, an n-octet frame) and starts on lane 0.
//   reset()                     DIC = 0 (the count is reset only at initialisation)
//   method                      0 deficit idle count, 1 always insert (both allowed by 46.3.1.4)
//   next_gap(n, mac_gap)        the gap after an n-octet frame when the MAC asks for mac_gap (12 or more)
//   deleted, inserted, dic      what the last call did, and the count after it
// Faults: ipg_min_only (always deletes, ignoring the bound), dic_max4 (bounds the count at 4, not 3),
//         start_any_lane (no alignment: the gap is always mac_gap).
module eth_gap;
  bit ipg_min_only = 0, dic_max4 = 0, start_any_lane = 0;
  int method = 0, dic = 0, deleted = 0, inserted = 0;
  function automatic void reset(); dic = 0; deleted = 0; inserted = 0; endfunction
  function automatic int next_gap(input int n, input int mac_gap);
    int m, top;
    deleted = 0; inserted = 0;
    m = (n + mac_gap) % 4;                       // lanes past lane 0 the next Start would land on
    if (start_any_lane || m == 0) return mac_gap;
    top = dic_max4 ? 4 : 3;
    if (method == 0 && (ipg_min_only || dic + m <= top)) begin deleted = m; dic = dic + m; end
    else begin inserted = 4 - m; if (method == 0) dic = dic - (4 - m); end
    return mac_gap - deleted + inserted;
  endfunction
endmodule
Read included file: eth_xgmii.sv
`timescale 1ns/1ns
// eth_rs: the packet as XGMII characters (9 bits: control flag and octet), four lanes per column, and the
// 66-bit block each pair of columns becomes.
//   clear(), put(c, d), idle(k)
//   lanes            4 for the XGMII and 25GMII (default), 8 for the 64-bit interfaces (XLGMII to 800GMII, P11.18)
//   start_packet()   adds idle until lane 0, then Start (FBh), six preamble octets and the SFD
//   end_packet()     Terminate (FDh)
//   columns(), lane_of(i)   columns of lanes characters; the lane of character i
//   block_info(g)    {valid, sync[1:0], type[7:0]} for characters 8g to 8g+7 (pad the tail with idle first)
// Fault: start_any_lane (Start is not aligned to lane 0).
module eth_rs;
  bit start_any_lane = 0;
  int lanes = 4;
  bit [8:0] ch [0:4095];
  int nch = 0;
  function automatic void clear(); nch = 0; endfunction
  function automatic void put(input bit c, input [7:0] d); ch[nch] = {c, d}; nch++; endfunction
  function automatic void idle(input int k); for (int i = 0; i < k; i++) put(1'b1, 8'h07); endfunction
  function automatic void start_packet();
    if (!start_any_lane) while (nch % lanes != 0) put(1'b1, 8'h07);
    put(1'b1, 8'hfb);
    for (int i = 0; i < 6; i++) put(1'b0, 8'h55);
    put(1'b0, 8'hd5);
  endfunction
  function automatic void end_packet(); put(1'b1, 8'hfd); endfunction
  function automatic void fill_to(input int multiple); while (nch % multiple != 0) put(1'b1, 8'h07); endfunction
  function automatic int columns(); return (nch + lanes - 1) / lanes; endfunction
  function automatic int lane_of(input int i); return i % lanes; endfunction
  function automatic bit is_c(input int i); return ch[i][8]; endfunction
  function automatic bit is_code(input int i, input [7:0] v); return ch[i] == {1'b1, v}; endfunction
  function automatic bit is_plain(input int i);            // a control character with a 7-bit C code
    return is_code(i, 8'h07) || is_code(i, 8'h06) || is_code(i, 8'hfe);
  endfunction
  function automatic bit all_data(input int a, input int b);
    for (int i = a; i <= b; i++) if (is_c(i)) return 0;
    return 1;
  endfunction
  function automatic bit all_plain(input int a, input int b);
    for (int i = a; i <= b; i++) if (!is_plain(i)) return 0;
    return 1;
  endfunction
  function automatic [10:0] block_info(input int g);
    int b; reg [7:0] t; bit ok;
    b = 8 * g; ok = 0; t = 8'h00;
    if (all_data(b, b + 7)) return {1'b1, 2'b01, 8'h00};
    if (all_plain(b, b + 7)) begin ok = 1; t = 8'h1e; end
    else if (is_code(b, 8'hfb) && all_data(b + 1, b + 7)) begin ok = 1; t = 8'h78; end
    else if (all_plain(b, b + 3) && is_code(b + 4, 8'hfb) && all_data(b + 5, b + 7)) begin ok = 1; t = 8'h33; end
    else if (is_code(b, 8'h9c) && all_data(b + 1, b + 3) && is_code(b + 4, 8'hfb) && all_data(b + 5, b + 7)) begin ok = 1; t = 8'h66; end
    else if (is_code(b, 8'h9c) && all_data(b + 1, b + 3) && is_code(b + 4, 8'h9c) && all_data(b + 5, b + 7)) begin ok = 1; t = 8'h55; end
    else if (is_code(b, 8'h9c) && all_data(b + 1, b + 3) && all_plain(b + 4, b + 7)) begin ok = 1; t = 8'h4b; end
    else if (all_plain(b, b + 3) && is_code(b + 4, 8'h9c) && all_data(b + 5, b + 7)) begin ok = 1; t = 8'h2d; end
    else begin
      for (int k = 0; k < 8; k++)
        if (!ok && is_code(b + k, 8'hfd) && (k == 0 || all_data(b, b + k - 1)) && (k == 7 || all_plain(b + k + 1, b + 7))) begin
          ok = 1;
          case (k)
            0: t = 8'h87; 1: t = 8'h99; 2: t = 8'haa; 3: t = 8'hb4;
            4: t = 8'hcc; 5: t = 8'hd2; 6: t = 8'he1; default: t = 8'hff;
          endcase
        end
    end
    return {ok, 2'b10, t};
  endfunction
endmodule

// eth_xgmii_mon: reads XGMII columns as a receiving RS would (46.2, 46.3.3) and reports what it sees.
// A column is {c[3:0], d[31:0]}: lane k is control flag c[k] and octet d[8k+7:8k]; lane 0 comes first.
//   reset(), col(c, d)      one column; col() returns 1 if the column holds anything the monitor flags
//   frames                  Starts seen on lane 0; octets: data octets after the SFD up to the Terminate
//   start_lane, term_lane   where the last Start and Terminate were (-1: not in this column)
//   bad_start               Starts on lanes 1 to 3 (46.3.3.3: the RS must not pass them to the MAC)
//   errors                  Error characters (FEh) seen inside a frame; err_frames: frames that carried one
//   seq_cols                columns holding a Sequence ordered set (9Ch in lane 0, P11.19)
//   last_len                data octets of the last frame, preamble and SFD excluded
module eth_xgmii_mon;
  int frames = 0, octets = 0, bad_start = 0, errors = 0, err_frames = 0, seq_cols = 0, last_len = 0;
  int start_lane = -1, term_lane = -1, in_pkt = 0, pre_left = 0, len = 0;
  bit had_err = 0;
  function automatic void reset();
    frames = 0; octets = 0; bad_start = 0; errors = 0; err_frames = 0; seq_cols = 0; last_len = 0;
    in_pkt = 0; pre_left = 0; len = 0; had_err = 0; start_lane = -1; term_lane = -1;
  endfunction
  function automatic bit col(input [3:0] c, input [31:0] d);
    bit flag; reg [7:0] o;
    flag = 0; start_lane = -1; term_lane = -1;
    if (c[0] && d[7:0] == 8'h9c) seq_cols++;
    for (int k = 0; k < 4; k++) begin
      o = d[8*k +: 8];
      if (c[k] && o == 8'hfb) begin
        start_lane = k;
        if (k != 0) begin bad_start++; flag = 1; end
        else begin in_pkt = 1; pre_left = 7; len = 0; had_err = 0; frames++; end
      end
      else if (in_pkt && c[k] && o == 8'hfd) begin
        term_lane = k; in_pkt = 0; last_len = len;
        if (had_err) err_frames++;
      end
      else if (in_pkt && c[k] && o == 8'hfe) begin errors++; had_err = 1; flag = 1; len++; end
      else if (in_pkt && !c[k]) begin
        if (pre_left > 0) pre_left--;
        else begin len++; octets++; end
      end
    end
    return flag;
  endfunction
endmodule

Check Yourself

Predict the outputThe program writes three Remote Fault ordered sets, then idle, and runs the monitor. What does it print?
`timescale 1ns/1ns
module tb;
  eth_frame f(); eth_rs rs(); eth_xgmii_mon mon();
  reg [3:0] c; reg [31:0] d; bit fl;
  // one frame of len data octets onto the lanes, then a Terminate and gap idles
  task automatic packet(input int len, input int gap);
    for (int i = 0; i < len; i++) f.pay[i] = i;
    f.build(48'h0a0000000002, 48'h0a0000000001, 16'h0800, len);
    rs.start_packet();
    for (int i = 0; i < f.n; i++) rs.put(1'b0, f.oct[i]);
    rs.end_packet(); rs.idle(gap);
  endtask
  function automatic string name(input int i);
    if (!rs.is_c(i)) return $sformatf("%h", rs.ch[i][7:0]);
    case (rs.ch[i][7:0]) 8'h07: return "I"; 8'hfb: return "S"; 8'hfd: return "T"; 8'hfe: return "E"; 8'h9c: return "Q"; default: return "?"; endcase
  endfunction
  // column k as {c, d}, lane 0 in the low bits
  task automatic column(input int k);
    for (int l = 0; l < 4; l++) begin c[l] = rs.ch[4*k + l][8]; d[8*l +: 8] = rs.ch[4*k + l][7:0]; end
  endtask
  task automatic show(input int k);
    column(k);
    $display("column %0d: %0s %0s %0s %0s  control flags, lane 0 first: %b", k, name(4*k), name(4*k + 1), name(4*k + 2), name(4*k + 3), {c[0], c[1], c[2], c[3]});
  endtask
  task automatic run_mon();
    mon.reset();
    for (int k = 0; k < rs.columns(); k++) begin column(k); fl = mon.col(c, d); end
  endtask
  initial begin
    rs.clear();
    for (int k = 0; k < 3; k++) begin rs.put(1'b1, 8'h9c); rs.put(1'b0, 8'h00); rs.put(1'b0, 8'h00); rs.put(1'b0, 8'h02); end
    rs.idle(8);
    run_mon();
    $display("%0d", mon.seq_cols);
    $finish;
  end
endmodule
Read included file: hs_pkg.sv
`timescale 1ns/1ns
// hs_pkg.sv: shared pure functions, and the bench random generator (read-only).
package hs_pkg;
  // xorshift32 (Marsaglia 2003): a linear generator over GF(2), period 2^32 - 1. A zero state is
  // replaced by 1, because zero maps to itself.
  function automatic [31:0] xs32(input [31:0] s);
    reg [31:0] x;
    x = (s == 32'd0) ? 32'd1 : s;
    x = x ^ (x << 13); x = x ^ (x >> 17); x = x ^ (x << 5);
    return x;
  endfunction
  // A Fibonacci PRBS generator x^n + x^m + 1 (PRBS7: 7,6; PRBS9: 9,5; PRBS15: 15,14; PRBS23: 23,18;
  // PRBS31: 31,28). The output bit is s[n-1]; the next state shifts the feedback into bit 0.
  function automatic [31:0] prbs_next(input [31:0] s, input int n, input int m);
    reg fb;
    fb = s[n-1] ^ s[m-1];
    return ((s << 1) | {31'd0, fb}) & ((n == 32) ? 32'hffffffff : ((32'd1 << n) - 32'd1));
  endfunction
  function automatic int ones(input [63:0] v);
    int n; n = 0;
    for (int i = 0; i < 64; i++) n += v[i];
    return n;
  endfunction
  // GF(16) with x^4 + x + 1, and GF(1024) with x^10 + x^3 + 1: shift-and-add multiply, no tables.
  function automatic [3:0] gf16_mul(input [3:0] a, input [3:0] b);
    reg [3:0] p, x; p = 4'd0; x = a;
    for (int i = 0; i < 4; i++) begin
      if (b[i]) p = p ^ x;
      x = x[3] ? ({x[2:0], 1'b0} ^ 4'b0011) : {x[2:0], 1'b0};
    end
    return p;
  endfunction
  function automatic [3:0] gf16_pow(input int e);   // alpha^e, alpha = x
    reg [3:0] p; int k; p = 4'd1; k = e % 15; if (k < 0) k += 15;
    for (int i = 0; i < k; i++) p = gf16_mul(p, 4'd2);
    return p;
  endfunction
  function automatic int gf16_log(input [3:0] a);   // -1 for 0
    reg [3:0] p; p = 4'd1;
    if (a == 4'd0) return -1;
    for (int i = 0; i < 15; i++) begin if (p == a) return i; p = gf16_mul(p, 4'd2); end
    return -1;
  endfunction
  function automatic [9:0] gf1024_mul(input [9:0] a, input [9:0] b);
    reg [9:0] p, x; p = 10'd0; x = a;
    for (int i = 0; i < 10; i++) begin
      if (b[i]) p = p ^ x;
      x = x[9] ? ({x[8:0], 1'b0} ^ 10'b0000001001) : {x[8:0], 1'b0};
    end
    return p;
  endfunction
  function automatic [9:0] gf1024_pow(input int e);
    reg [9:0] p; int k; p = 10'd1; k = e % 1023; if (k < 0) k += 1023;
    for (int i = 0; i < k; i++) p = gf1024_mul(p, 10'd2);
    return p;
  endfunction
endpackage

// hs_rng: the bench's random numbers. Same seed, same numbers, on every engine.
module hs_rng;
  int unsigned s = 32'h2545f491;
  function automatic void seed(input int unsigned v); s = (v == 0) ? 32'd1 : v; endfunction
  function automatic int unsigned next(); s = hs_pkg::xs32(s); return s; endfunction
  function automatic int below(input int n); s = hs_pkg::xs32(s); return (n <= 0) ? 0 : int'(s % n); endfunction
  function automatic bit bit1(); s = hs_pkg::xs32(s); return s[16]; endfunction
  function automatic bit chance_ppm(input int ppm); s = hs_pkg::xs32(s); return (s % 1000000) < ppm; endfunction
  function automatic [7:0] byte8(); s = hs_pkg::xs32(s); return s[23:16]; endfunction
endmodule
Read included file: hs_code.sv
`timescale 1ns/1ns
// hs_code.sv: line codes, CRCs and scramblers (read-only).

// ---------------------------------------------------------------------------------------------
// hs_8b10b: 8b/10b encoder and decoder with running disparity and the 12 K codes.
// code[9:0] = {a,b,c,d,e,i,f,g,h,j}; bit a (code[9]) goes on the wire first. rd: 0 = RD-, 1 = RD+.
//   encode(d, k, rd_in) -> {rd_out, code[9:0]}            (11 bits)
//   decode(code, rd_in) -> {rd_out, disp_err, code_err, k, d[7:0]}   (12 bits)
//   enc(d, k) / dec(code): the same, with the running disparity kept in rd_tx / rd_rx
// A K request for a byte that is not one of the 12 K codes is encoded as data and counted in bad_k.
// Decoder: code_err = the code is in neither column of the table; disp_err = it is a valid code
// only in the other column. rd_out follows the sub-block rule on the received bits.
// Faults: no_rd (always the RD- column), a7_never (never the alternate D.x.A7),
//         keep_rd_on_unbalanced (the 4b sub-block is chosen with the disparity from before the 6b one),
//         no_balanced_flip (D.07 and D.x.3 keep their RD- form at RD+), dec_no_disp_check.
module hs_8b10b;
  bit no_rd = 0, a7_never = 0, keep_rd_on_unbalanced = 0, no_balanced_flip = 0, dec_no_disp_check = 0;
  bit trace = 0;
  bit rd_tx = 0, rd_rx = 0;
  int bad_k = 0, symbols = 0, code_errs = 0, disp_errs = 0;
  bit last_k = 0, last_code_err = 0, last_disp_err = 0;
  bit valid_m [0:1023]; bit valid_p [0:1023]; bit [8:0] kd [0:1023]; bit built = 0;
  function automatic [5:0] t6(input [4:0] x);   // 5b/6b, RD- column, abcdei
    case (x)
      5'd0: return 6'b100111;  5'd1: return 6'b011101;  5'd2: return 6'b101101;  5'd3: return 6'b110001;
      5'd4: return 6'b110101;  5'd5: return 6'b101001;  5'd6: return 6'b011001;  5'd7: return 6'b111000;
      5'd8: return 6'b111001;  5'd9: return 6'b100101;  5'd10: return 6'b010101; 5'd11: return 6'b110100;
      5'd12: return 6'b001101; 5'd13: return 6'b101100; 5'd14: return 6'b011100; 5'd15: return 6'b010111;
      5'd16: return 6'b011011; 5'd17: return 6'b100011; 5'd18: return 6'b010011; 5'd19: return 6'b110010;
      5'd20: return 6'b001011; 5'd21: return 6'b101010; 5'd22: return 6'b011010; 5'd23: return 6'b111010;
      5'd24: return 6'b110011; 5'd25: return 6'b100110; 5'd26: return 6'b010110; 5'd27: return 6'b110110;
      5'd28: return 6'b001110; 5'd29: return 6'b101110; 5'd30: return 6'b011110; default: return 6'b101011;
    endcase
  endfunction
  function automatic [3:0] t4d(input [2:0] y);  // 3b/4b data, RD- column, fghj (y = 7 is P7)
    case (y)
      3'd0: return 4'b1011; 3'd1: return 4'b1001; 3'd2: return 4'b0101; 3'd3: return 4'b1100;
      3'd4: return 4'b1101; 3'd5: return 4'b1010; 3'd6: return 4'b0110; default: return 4'b1110;
    endcase
  endfunction
  function automatic [3:0] t4k(input [2:0] y);  // 3b/4b for K codes, RD- form before the flip
    case (y)
      3'd0: return 4'b1011; 3'd1: return 4'b0110; 3'd2: return 4'b1010; 3'd3: return 4'b1100;
      3'd4: return 4'b1101; 3'd5: return 4'b0101; 3'd6: return 4'b1001; default: return 4'b0111;
    endcase
  endfunction
  function automatic bit k_ok(input [7:0] d);
    return d[4:0] == 5'd28 || d == 8'hf7 || d == 8'hfb || d == 8'hfd || d == 8'hfe;
  endfunction
  function automatic int n6(input [5:0] v); return v[0] + v[1] + v[2] + v[3] + v[4] + v[5]; endfunction
  function automatic int n4(input [3:0] v); return v[0] + v[1] + v[2] + v[3]; endfunction
  // running disparity at the end of a sub-block (more ones: +; more zeros: -; 000111 and 0011: +; 111000 and 1100: -)
  function automatic bit rd6(input [5:0] v, input bit rd);
    return (n6(v) > 3) ? 1'b1 : (n6(v) < 3) ? 1'b0 : (v == 6'b000111) ? 1'b1 : (v == 6'b111000) ? 1'b0 : rd;
  endfunction
  function automatic bit rd4(input [3:0] v, input bit rd);
    return (n4(v) > 2) ? 1'b1 : (n4(v) < 2) ? 1'b0 : (v == 4'b0011) ? 1'b1 : (v == 4'b1100) ? 1'b0 : rd;
  endfunction
  // faults: [0] no_rd [1] a7_never [2] keep_rd_on_unbalanced [3] no_balanced_flip
  function automatic [10:0] core(input [7:0] d, input bit k, input bit rd_in, input [3:0] f);
    reg [5:0] six; reg [3:0] four; reg rd0, r6, rd1, a7, kk; reg [4:0] x; reg [2:0] y; int o6, o4;
    x = d[4:0]; y = d[7:5]; kk = k && k_ok(d); rd0 = f[0] ? 1'b0 : rd_in;
    six = (kk && x == 5'd28) ? 6'b001111 : t6(x); o6 = n6(six);
    if (rd0 && (o6 != 3 || (six == 6'b111000 && !f[3]))) begin six = ~six; o6 = 6 - o6; end
    r6 = (o6 > 3) ? 1'b1 : (o6 < 3) ? 1'b0 : (six == 6'b000111) ? 1'b1 : (six == 6'b111000) ? 1'b0 : rd0;
    rd1 = f[2] ? rd0 : r6;
    if (kk) begin
      four = t4k(y); if (rd1) four = ~four;
    end else begin
      a7 = (y == 3'd7) && !f[1] && ((!rd1 && (x == 5'd17 || x == 5'd18 || x == 5'd20)) || (rd1 && (x == 5'd11 || x == 5'd13 || x == 5'd14)));
      four = a7 ? 4'b0111 : t4d(y);
      if (rd1 && (n4(four) != 2 || (four == 4'b1100 && !f[3]))) four = ~four;
    end
    o4 = n4(four);
    return {(o4 > 2) ? 1'b1 : (o4 < 2) ? 1'b0 : (four == 4'b0011) ? 1'b1 : (four == 4'b1100) ? 1'b0 : r6, six, four};
  endfunction
  function automatic [10:0] encode(input [7:0] d, input bit k, input bit rd_in);
    if (k && !k_ok(d)) bad_k++;
    return core(d, k, rd_in, {no_balanced_flip, keep_rd_on_unbalanced, a7_never, no_rd});
  endfunction
  function automatic void build();
    reg [10:0] c;
    for (int i = 0; i < 1024; i++) begin valid_m[i] = 0; valid_p[i] = 0; kd[i] = 9'd0; end
    for (int i = 0; i < 268; i++) begin
      reg [7:0] d; reg k;
      if (i < 256) begin d = i[7:0]; k = 0; end
      else begin k = 1; d = (i < 264) ? {3'(i - 256), 5'd28} : (i == 264) ? 8'hf7 : (i == 265) ? 8'hfb : (i == 266) ? 8'hfd : 8'hfe; end
      c = core(d, k, 1'b0, 4'd0); valid_m[c[9:0]] = 1; kd[c[9:0]] = {k, d};
      c = core(d, k, 1'b1, 4'd0); valid_p[c[9:0]] = 1; kd[c[9:0]] = {k, d};
    end
    built = 1;
  endfunction
  function automatic [11:0] decode(input [9:0] code, input bit rd_in);
    reg here, there, ce, de, r;
    if (!built) build();
    here = rd_in ? valid_p[code] : valid_m[code];
    there = rd_in ? valid_m[code] : valid_p[code];
    ce = !(here || there); de = !ce && !here && !dec_no_disp_check;
    r = rd4(code[3:0], rd6(code[9:4], rd_in));
    return {r, de, ce, ce ? 9'd0 : kd[code]};
  endfunction
  function automatic [9:0] enc(input [7:0] d, input bit k);
    reg [10:0] r; r = encode(d, k, rd_tx); rd_tx = r[10];
    if (trace) $display("s%0d TX %s%0d.%0d code=%b rd=%s", symbols, (k && k_ok(d)) ? "K" : "D", d[4:0], d[7:5], r[9:0], r[10] ? "+" : "-");
    symbols++;
    return r[9:0];
  endfunction
  function automatic [8:0] dec(input [9:0] code);
    reg [11:0] r; r = decode(code, rd_rx); rd_rx = r[11];
    last_disp_err = r[10]; last_code_err = r[9]; last_k = r[8];
    if (r[9]) code_errs++; if (r[10]) disp_errs++;
    if (trace && (r[9] || r[10])) $display("RX %b %s", code, r[9] ? "code error" : "disparity error");
    return r[8:0];
  endfunction
  function automatic bit comma7(input [6:0] w); return w == 7'b0011111 || w == 7'b1100000; endfunction
endmodule

// ---------------------------------------------------------------------------------------------
// hs_crc: a CRC of 1 to 32 bits with any polynomial, seed, bit order and final inversion.
// The register shifts left; the polynomial omits the x^width term. The field is sent register bit
// width-1 first (USB 2.0, USB 3.2 and Ethernet all send it this way).
//   use_crc32(), use_crc16_usb2(), use_crc5_usb2(), use_crc16_usb3(): parameter sets
//   reset(), crc_bit(b), crc_byte(v), crc_bits(v, n), field(), field_bit(i), check_value(), crc_residue_ok()
// Faults: msb_first (bytes enter MSB first), no_invert (the field is not complemented), seed_zero.
module hs_crc;
  int width = 32;
  bit [31:0] poly = 32'h04c11db7, seed = 32'hffffffff, residue = 32'hc704dd7b;
  bit lsb_first = 1, invert = 1;
  bit msb_first = 0, no_invert = 0, seed_zero = 0;
  bit [31:0] r = 32'hffffffff;
  function automatic [31:0] mask(); return (width >= 32) ? 32'hffffffff : ((32'd1 << width) - 32'd1); endfunction
  function automatic void reset(); r = seed_zero ? 32'd0 : (seed & mask()); endfunction
  function automatic void set(input int w, input [31:0] p, input [31:0] s, input [31:0] res, input bit lsb, input bit inv);
    width = w; poly = p; seed = s; residue = res; lsb_first = lsb; invert = inv; reset();
  endfunction
  function automatic void use_crc32();      set(32, 32'h04c11db7, 32'hffffffff, 32'hc704dd7b, 1, 1); endfunction
  function automatic void use_crc16_usb2(); set(16, 32'h8005, 32'hffff, 32'h800d, 1, 1); endfunction
  function automatic void use_crc5_usb2();  set(5, 32'h05, 32'h1f, 32'h0c, 1, 1); endfunction
  function automatic void use_crc16_usb3(); set(16, 32'h100b, 32'hffff, 32'hf6aa, 1, 1); endfunction
  function automatic void crc_bit(input bit b);
    reg fb; fb = b ^ r[width - 1];
    r = ((r << 1) ^ (fb ? poly : 32'd0)) & mask();
  endfunction
  function automatic void crc_byte(input [7:0] v);
    for (int i = 0; i < 8; i++) crc_bit(v[(lsb_first ^ msb_first) ? i : 7 - i]);
  endfunction
  function automatic void crc_bits(input [31:0] v, input int n);   // n bits of v, bit 0 first
    for (int i = 0; i < n; i++) crc_bit(v[i]);
  endfunction
  function automatic [31:0] field(); return (invert && !no_invert) ? (~r & mask()) : r; endfunction
  function automatic bit field_bit(input int i); reg [31:0] f; f = field(); return f[width - 1 - i]; endfunction
  // the usual published "check" number: the field with its first-sent bit read as bit 0
  function automatic [31:0] check_value();
    reg [31:0] f, o; f = field(); o = 32'd0;
    for (int i = 0; i < width; i++) o[i] = f[width - 1 - i];
    return lsb_first ? o : f;
  endfunction
  function automatic bit crc_residue_ok(); return r == (residue & mask()); endfunction
endmodule

// ---------------------------------------------------------------------------------------------
// hs_scr: additive (frame-synchronous) and multiplicative (self-synchronising) scramblers.
// poly holds the coefficients: bit k is x^k; the +1 term is always used (taps() sets bit 0); len is the degree.
// Additive: a Galois LFSR. The key bit is s[len-1]; each step shifts left and adds the low terms of
//   the polynomial when the key bit is 1. The data never enters the register.
// Multiplicative: the line bit is the data bit XOR the register bits at the polynomial's terms;
//   the scrambler shifts its own output in, the descrambler shifts the received line bit in.
//   scr_add(len, poly, seed), scr_mul(len, poly), use_usb3_gen1(), use_x58(), use_x23_usb3() (see its note)
//   scr_bit(b), dscr_bit(b), scr_byte(v), dscr_byte(v) (bit 0 first), scr_reset(), scr_hold() (a skip
//   symbol: no step), scr_unscrambled() (a symbol sent in the clear: 8 steps, data untouched)
// Faults: advance_on_skip (scr_hold steps the LFSR 8 times), no_reset (scr_reset does nothing),
//         wrong_tap (the lowest term x^k becomes x^(k+1)), seed_zero (scr_reset loads 0).
module hs_scr;
  bit mult = 0; int len = 16;
  bit [63:0] poly = 64'h10039, seed = 64'hffff;
  bit advance_on_skip = 0, no_reset = 0, wrong_tap = 0, seed_zero = 0;
  bit [63:0] s = 64'hffff;
  int steps = 0;
  function automatic [63:0] lmask(); return (len >= 64) ? 64'hffffffffffffffff : ((64'd1 << len) - 64'd1); endfunction
  function automatic [63:0] taps();
    reg [63:0] p; int k; p = poly | 64'd1; k = 1;
    if (wrong_tap) begin
      while (k < len && !p[k]) k++;
      if (k < len) begin p[k] = 1'b0; p[k + 1] = 1'b1; end
    end
    return p;
  endfunction
  function automatic void load(); s = (seed_zero ? 64'd0 : seed) & lmask(); endfunction
  function automatic void scr_add(input int n, input [63:0] p, input [63:0] sd); mult = 0; len = n; poly = p; seed = sd; s = sd & lmask(); endfunction
  function automatic void scr_mul(input int n, input [63:0] p); mult = 1; len = n; poly = p; seed = 64'd0; s = 64'd0; endfunction
  function automatic void use_usb3_gen1(); scr_add(16, 64'h10039, 64'hffff); endfunction   // x^16 + x^5 + x^4 + x^3 + 1, seed FFFFh
  function automatic void use_x58(); scr_mul(58, (64'd1 << 58) | (64'd1 << 39) | 64'd1); endfunction   // x^58 + x^39 + 1
  // USB 3.2 Gen 2 (§6.3.2.3) polynomial x^23 + x^21 + x^16 + x^8 + x^5 + x^2 + 1 with seed 1DBFBCh. Only the
  // polynomial and seed are the specification's: the register form here is this library's Galois form, and
  // the reset and bypass rules of §6.3.2.3 are not modelled, so do not quote its key stream as USB's.
  function automatic void use_x23_usb3(); scr_add(23, (64'd1 << 23) | (64'd1 << 21) | (64'd1 << 16) | (64'd1 << 8) | (64'd1 << 5) | (64'd1 << 2) | 64'd1, 64'h1dbfbc); endfunction
  function automatic void scr_reset(); if (!no_reset) load(); endfunction
  function automatic bit key(); return s[len - 1]; endfunction
  function automatic void step();
    reg kb; kb = s[len - 1];
    s = ((s << 1) & lmask()) ^ (kb ? (taps() & lmask()) : 64'd0);
    steps++;
  endfunction
  // the XOR of the register bits at the polynomial's terms x^1..x^len (bit k-1 of the register for x^k)
  function automatic bit fbx(input [63:0] st); return ^(st & (taps() >> 1) & lmask()); endfunction
  function automatic bit scr_bit(input bit b);
    reg o;
    if (!mult) begin o = b ^ s[len - 1]; step(); end
    else begin o = b ^ fbx(s); s = ((s << 1) | {63'd0, o}) & lmask(); steps++; end
    return o;
  endfunction
  function automatic bit dscr_bit(input bit b);
    reg o;
    if (!mult) begin o = b ^ s[len - 1]; step(); end
    else begin o = b ^ fbx(s); s = ((s << 1) | {63'd0, b}) & lmask(); steps++; end
    return o;
  endfunction
  function automatic [7:0] scr_byte(input [7:0] v);
    reg [7:0] o; for (int i = 0; i < 8; i++) o[i] = scr_bit(v[i]); return o;
  endfunction
  function automatic [7:0] dscr_byte(input [7:0] v);
    reg [7:0] o; for (int i = 0; i < 8; i++) o[i] = dscr_bit(v[i]); return o;
  endfunction
  // a skip symbol passes unscrambled and the LFSR holds
  function automatic void scr_hold(); if (advance_on_skip && !mult) for (int i = 0; i < 8; i++) step(); endfunction
  // another symbol that is sent unscrambled (a K code other than COM and SKP): the LFSR still steps 8 times
  function automatic void scr_unscrambled(); if (!mult) for (int i = 0; i < 8; i++) step(); endfunction
endmodule
Read included file: eth_mac.sv
`timescale 1ns/1ns
// eth_frame: one MAC frame as octets, its packet as wire bits, and a bit-serial receiver.
//   pay[i]                         client data, set by the bench before build()
//   build(da, sa, lt, len)         destination, source, Length/Type, len data octets, then the FCS -> oct[0..n-1].
//                                  It adds no pad: give it 46 data octets or more. (Padding is P11.2.1's task; the
//                                  pages show the padding MAC's frames as measured tables.)
//   wire_bits(), wire_bit(i)       the packet in transmit order: preamble, SFD, frame
//   rx_start(), rx_bit(b), rx_end()  hunt for the SFD, collect octets, then parse()
//   parse()                        da, sa, lt, is_length, is_type, data_len, fcs_rx, fcs_calc, fcs_ok
// Faults: fcs_msb_first, fcs_no_invert, fcs_covers_preamble, sfd_wrong, msb_first_octets.
module eth_frame;
  localparam int MIN_FRAME = 64, MAX_BASIC = 1518, MAX_QTAG = 1522, MAX_ENVELOPE = 2000;
  bit fcs_msb_first = 0, fcs_no_invert = 0, fcs_covers_preamble = 0, sfd_wrong = 0, msb_first_octets = 0;
  hs_crc crc();
  bit [7:0] pay [0:2047];
  bit [7:0] oct [0:2047];
  int n = 0;
  bit [47:0] da = 0, sa = 0; bit [15:0] lt = 0;
  bit is_length = 0, is_type = 0, fcs_ok = 0;
  int data_len = 0;
  bit [31:0] fcs_rx = 0, fcs_calc = 0;
  // receiver state
  bit in_frame = 0; bit [7:0] hist = 0, cur = 0; int nb = 0, excess = 0, sfd_at = -1, bits_seen = 0;

  // The FCS of oct[0..len-1] as four octets: the first octet sent is in [7:0].
  function automatic [31:0] fcs_of(input int len);
    crc.use_crc32(); crc.msb_first = fcs_msb_first; crc.no_invert = fcs_no_invert; crc.reset();
    if (fcs_covers_preamble) begin
      for (int i = 0; i < 7; i++) crc.crc_byte(8'h55);
      crc.crc_byte(8'hd5);
    end
    for (int i = 0; i < len; i++) crc.crc_byte(oct[i]);
    return crc.check_value();
  endfunction

  function automatic void build(input [47:0] d, input [47:0] s, input [15:0] t, input int len);
    int k; reg [31:0] f;
    k = 0;
    for (int i = 0; i < 6; i++) begin oct[k] = d[47 - 8*i -: 8]; k++; end
    for (int i = 0; i < 6; i++) begin oct[k] = s[47 - 8*i -: 8]; k++; end
    oct[k] = t[15:8]; k++;
    oct[k] = t[7:0]; k++;
    for (int i = 0; i < len; i++) begin oct[k] = pay[i]; k++; end
    f = fcs_of(k);
    for (int i = 0; i < 4; i++) begin oct[k] = f[8*i +: 8]; k++; end
    n = k; excess = 0;
    parse();
  endfunction

  function automatic void parse();
    da = 0; sa = 0; lt = 0; is_length = 0; is_type = 0; fcs_ok = 0; data_len = 0; fcs_rx = 0; fcs_calc = 0;
    if (n >= 14) begin
      da = {oct[0], oct[1], oct[2], oct[3], oct[4], oct[5]};
      sa = {oct[6], oct[7], oct[8], oct[9], oct[10], oct[11]};
      lt = {oct[12], oct[13]};
      is_length = (lt <= 16'd1500);
      is_type = (lt >= 16'd1536);
    end
    if (n >= 18) begin
      fcs_rx = {oct[n-1], oct[n-2], oct[n-3], oct[n-4]};
      fcs_calc = fcs_of(n - 4);
      fcs_ok = (fcs_rx == fcs_calc);
      data_len = is_length ? int'(lt) : n - 18;
    end
  endfunction

  function automatic int wire_bits(); return 8 * (8 + n); endfunction
  function automatic bit wire_bit(input int i);
    int o, b; reg [7:0] v;
    o = i / 8; b = i % 8;
    if (o < 7) v = 8'h55;
    else if (o == 7) v = sfd_wrong ? 8'h55 : 8'hd5;
    else v = oct[o - 8];
    return msb_first_octets ? v[7 - b] : v[b];
  endfunction

  function automatic void rx_start();
    in_frame = 0; hist = 0; cur = 0; nb = 0; n = 0; excess = 0; sfd_at = -1; bits_seen = 0;
  endfunction
  function automatic void rx_bit(input bit b);
    bits_seen++;
    if (!in_frame) begin
      hist = {hist[6:0], b};                      // the oldest bit is hist[7]
      if (hist == 8'b10101011) begin in_frame = 1; sfd_at = bits_seen; end
    end else begin
      if (msb_first_octets) cur[7 - nb] = b; else cur[nb] = b;
      nb++;
      if (nb == 8) begin oct[n] = cur; n++; nb = 0; end
    end
  endfunction
  function automatic void rx_end(); excess = nb; parse(); endfunction
endmodule
// eth_axis: a MAC client bus in the style of AXI4-Stream (IHI 0051B 2.2 handshake, 2.5 TKEEP, 2.6 TLAST, 2.9 TUSER),
// 64 bits wide. Byte 0 of a beat is tdata[7:0] and is first in the frame (AXI4-Stream 2.4.1). Bench conventions,
// not AXI4-Stream's or 802.3's: tkeep is all ones except on the last beat, where it covers bytes 0 to k-1; one tuser
// bit (transfer-based, 2.9.1), read on the last beat only, marks a bad frame (receive) or asks the MAC to abort it
// (transmit).
//   load(n)                  beats for octets oct[0..n-1]: bd[], bk[], bl[], nbeats; bv[] = valid per cycle, ncyc
//   tx_cycles()              the transmit MAC: one beat per cycle once a frame has started. Returns 0 sent,
//                            1 underrun (tvalid fell inside the frame), 2 aborted by tuser. sent_octets, fail_cycle.
// Fault: tvalid_gap (load() leaves cycle 3 of the frame empty: the client was late with a beat).
module eth_axis;
  bit tvalid_gap = 0;
  bit [7:0] oct [0:2047];
  bit [63:0] bd [0:300]; bit [7:0] bk [0:300]; bit bl [0:300]; bit bu [0:300];
  int nbeats = 0;
  bit bv [0:301]; int bix [0:301]; int ncyc = 0;
  int sent_octets = 0, fail_cycle = -1;
  function automatic void load(input int n);
    int b, k;
    nbeats = (n + 7) / 8;
    for (b = 0; b < nbeats; b++) begin
      bd[b] = 64'd0; bk[b] = 8'd0; bl[b] = (b == nbeats - 1); bu[b] = 0;
      for (k = 0; k < 8; k++) if (8*b + k < n) begin bd[b][8*k +: 8] = oct[8*b + k]; bk[b][k] = 1'b1; end
    end
    ncyc = 0;
    for (b = 0; b < nbeats; b++) begin
      if (tvalid_gap && b == 3) begin bv[ncyc] = 0; bix[ncyc] = -1; ncyc++; end
      bv[ncyc] = 1; bix[ncyc] = b; ncyc++;
    end
  endfunction
  function automatic int tx_cycles();
    bit started; started = 0; sent_octets = 0; fail_cycle = -1;
    for (int c = 0; c < ncyc; c++) begin
      if (!bv[c]) begin
        if (started) begin fail_cycle = c; return 1; end
      end else begin
        started = 1;
        if (bl[bix[c]] && bu[bix[c]]) begin fail_cycle = c; return 2; end
        for (int k = 0; k < 8; k++) if (bk[bix[c]][k]) sent_octets++;
      end
    end
    return 0;
  endfunction
endmodule

// eth_pause: the PAUSE function of MAC Control (Annex 31B) at the station that receives PAUSE frames, in octet
// times (one octet time is 8 bit times; a pause quantum is 512 bit times = 64 octet times, 31B.2).
//   reset(), rx_pause(t, q)  a valid PAUSE frame with pause_time q ended at time t: the timer restarts (31B.3.3)
//   may_start(t)             1 when a new data frame may start at time t. A frame already started is never cut
//                            (31B.3.7). react is the bench's reaction time: frames may still start until t + react.
//   paused_until             the time the timer runs out
//   pause_octets(q, o[])     not here: build a PAUSE frame with eth_frame (DA 01-80-C2-00-00-01, 8808h, 0001h, q)
// Faults: pause_ignored, pause_adds_not_overrides (a new frame adds to the timer, and zero does not cancel),
//         slow_reaction (react = 70 quanta, over the 60 allowed at 10 Gb/s), timer_in_bits (q counts bit times).
module eth_pause;
  localparam int QUANTUM = 64;                     // octet times
  bit pause_ignored = 0, pause_adds_not_overrides = 0, slow_reaction = 0, timer_in_bits = 0;
  int react = 0, t_rx = -1, paused_until = 0;
  function automatic void reset(); t_rx = -1; paused_until = 0; endfunction
  function automatic void rx_pause(input int t, input int q);
    int len;
    if (pause_ignored) return;
    len = timer_in_bits ? (q + 7) / 8 : q * QUANTUM;
    if (pause_adds_not_overrides && paused_until > t) paused_until = paused_until + len;
    else paused_until = t + len;
    t_rx = t;
  endfunction
  function automatic bit may_start(input int t);
    int r;
    r = slow_reaction ? 70 * QUANTUM : react;
    if (t_rx < 0) return 1;
    if (t < t_rx + r) return 1;
    return t >= paused_until;
  endfunction
endmodule

// eth_pfc: priority-based flow control (Annex 31D). The frame is 802.3's; holding a priority's queue is the MAC
// Control client's job (IEEE 802.1Q, not held), so the eight timers here are a bench client, in octet times.
//   build(f_oct[], pev, times[])   not here: the bench writes opcode 01-01, the vector and eight times into eth_frame
//   reset(), rx(t, pev, tm[0..7])  for each e[n] = 1 (bit n of the vector's low octet), priority n stops until
//                                  t + 64 * time[n] (hold_end[n]); e[n] = 0 leaves priority n alone; time[n] = 0 releases it
//   blocked(n, t)                  1 while priority n is held
// Fault: pfc_wrong_priority (reads e[n] from bit 7 - n).
module eth_pfc;
  bit pfc_wrong_priority = 0;
  int hold_end [0:7];
  function automatic void reset(); for (int i = 0; i < 8; i++) hold_end[i] = 0; endfunction
  function automatic void rx(input int t, input [15:0] pev, input [127:0] tm);   // tm[16*n +: 16] = time[n]
    bit e;
    for (int n = 0; n < 8; n++) begin
      e = pfc_wrong_priority ? pev[7 - n] : pev[n];
      if (e) hold_end[n] = t + 64 * int'(tm[16*n +: 16]);
    end
  endfunction
  function automatic bit blocked(input int n, input int t); return t < hold_end[n]; endfunction
endmodule

// eth_csma_tx: one half-duplex transmitter (4.2.3.2), one call of tick() per octet time.
//   reset(), load(frame_octets)   a frame of frame_octets (DA to FCS) waits to be sent; it is padded to min_frame
//   tick(carrier)                 carrier: another station's signal is on the wire here now. Returns 1 when the
//                                 station puts an octet (packet or jam) on the wire.
//   plan[i]                       the wait, in slots, after collision i + 1. The bench sets it (default 0). This
//                                 readable station draws nothing and has no attempt limit.
//   state  0 idle, 1 defer, 2 send, 3 jam, 4 backoff, 5 sent (as far as the sender knows)
//   pkt, sent, quiet, left, attempts, late, last_start, last_r
// min_frame is 64 octets; a bench may lower it to show why it is 64. Fault: no_backoff (every wait is 0 slots).
// Deference is a bench simplification: the 12-octet quiet count restarts on any carrier, own or received, and the
// station never starts while carrier is present. 4.2.8 restarts only the first part of the gap, and then transmits
// whatever the carrier.
module eth_csma_tx;
  localparam int SLOT = 64, JAM = 4, GAP = 12, PRE = 8;   // octet times
  bit no_backoff = 0;
  int min_frame = 64;
  int plan [0:63];
  int state = 0, pkt = 0, sent = 0, quiet = GAP, left = 0, attempts = 0, late = 0, last_start = -1, last_r = 0, now = 0;
  function automatic void reset();
    state = 0; pkt = 0; sent = 0; quiet = GAP; left = 0; attempts = 0; late = 0; last_start = -1; last_r = 0; now = 0;
  endfunction
  function automatic void load(input int frame_octets);
    pkt = PRE + frame_octets;
    if (frame_octets < min_frame) pkt = PRE + min_frame;
    state = 1; attempts = 0; sent = 0; late = 0;
  endfunction
  function automatic bit tick(input bit carrier);
    bit on;
    on = 0;
    if (state == 1 && !carrier && quiet >= GAP) begin state = 2; sent = 0; last_start = now; end
    if (state == 2 && carrier) begin
      attempts++; if (sent > SLOT) late++;
      state = 3; left = JAM;
    end
    case (state)
      2: begin sent++; on = 1; if (sent == pkt) state = 5; end
      3: begin
           on = 1; left--;
           if (left == 0) begin
             last_r = no_backoff ? 0 : plan[(attempts - 1) % 64];
             left = SLOT * last_r;
             state = (left == 0) ? 1 : 4;
           end
         end
      4: begin left--; if (left == 0) state = 1; end
      default: ;
    endcase
    quiet = (carrier || on) ? 0 : ((quiet < GAP) ? quiet + 1 : GAP);
    now++;
    return on;
  endfunction
endmodule

// eth_csma: two eth_csma_tx stations, A and B, at the two ends of a wire with a one-way delay of d octet times.
//   run(fa, ready_a, fb, ready_b, tmax)   each station loads its frame (fa, fb octets) at its ready time
//   on_a[t], on_b[t]          what each station put on the wire at time t
//   ev_t[], ev_who[] (0 A, 1 B), ev_kind[], ev_v[], n_ev   the event log:
//     kind 0 starts attempt v; 1 sees a collision after v octets; 2 jam over, backs off v slots;
//     3 last octet sent (v = octets); 4 gives up after v attempts
//   delivered(i)              1 when station i's last attempt reached the far end with no overlap there
//   a.plan[], b.plan[], a.no_backoff, b.no_backoff, a.min_frame, b.min_frame: the stations' settings
module eth_csma;
  eth_csma_tx a(); eth_csma_tx b();
  int d = 10, n_ev = 0, tend = 0;
  bit on_a [0:16383]; bit on_b [0:16383];
  int ev_t [0:255]; int ev_who [0:255]; int ev_kind [0:255]; int ev_v [0:255];
  function automatic void log_ev(input int t, input int who, input int kind, input int v);
    if (n_ev < 256) begin ev_t[n_ev] = t; ev_who[n_ev] = who; ev_kind[n_ev] = kind; ev_v[n_ev] = v; n_ev++; end
  endfunction
  function automatic void note(input int t, input int who, input int s0, input int s1, input int sent0, input int att, input int r, input int sent1);
    if (s0 != 2 && s1 == 2) log_ev(t, who, 0, att + 1);
    if (s0 == 2 && (s1 == 3 || s1 == 4)) log_ev(t, who, 1, sent0);
    if (s0 == 3 && (s1 == 4 || s1 == 1)) log_ev(t, who, 2, r);
    if (s0 != 5 && s1 == 5) log_ev(t, who, 3, sent1);
    if (s0 != 6 && s1 == 6) log_ev(t, who, 4, att);
  endfunction
  function automatic void run(input int fa, input int ready_a, input int fb, input int ready_b, input int tmax);
    bit ca, cb; int sa, sb, xa, xb;
    a.reset(); b.reset(); n_ev = 0; tend = tmax;
    for (int t = 0; t < tmax; t++) begin
      if (t == ready_a) a.load(fa);
      if (t == ready_b) b.load(fb);
      ca = (t >= d) ? on_b[t - d] : 1'b0;
      cb = (t >= d) ? on_a[t - d] : 1'b0;
      sa = a.state; sb = b.state; xa = a.sent; xb = b.sent;
      on_a[t] = a.tick(ca);
      on_b[t] = b.tick(cb);
      note(t, 0, sa, a.state, xa, a.attempts, a.last_r, a.sent);
      note(t, 1, sb, b.state, xb, b.attempts, b.last_r, b.sent);
    end
  endfunction
  function automatic bit delivered(input int i);
    int s, p, u;
    if (i == 0 && a.state != 5) return 0;
    if (i == 1 && b.state != 5) return 0;
    s = (i == 0) ? a.last_start : b.last_start;
    p = (i == 0) ? a.pkt : b.pkt;
    for (int t = s; t < s + p; t++) begin
      u = t + d;
      if (u < tend && ((i == 0) ? on_b[u] : on_a[u])) return 0;
    end
    return 1;
  endfunction
endmodule

// eth_gap: how long the gap before the next Start is on a 4-lane XGMII, where Start must sit on lane 0
// (46.3.1.4). A gap counts every character from the Terminate to the last idle before Start. A packet is
// 8 + n characters (Start, six preamble octets, SFD, an n-octet frame) and starts on lane 0.
//   reset()                     DIC = 0 (the count is reset only at initialisation)
//   method                      0 deficit idle count, 1 always insert (both allowed by 46.3.1.4)
//   next_gap(n, mac_gap)        the gap after an n-octet frame when the MAC asks for mac_gap (12 or more)
//   deleted, inserted, dic      what the last call did, and the count after it
// Faults: ipg_min_only (always deletes, ignoring the bound), dic_max4 (bounds the count at 4, not 3),
//         start_any_lane (no alignment: the gap is always mac_gap).
module eth_gap;
  bit ipg_min_only = 0, dic_max4 = 0, start_any_lane = 0;
  int method = 0, dic = 0, deleted = 0, inserted = 0;
  function automatic void reset(); dic = 0; deleted = 0; inserted = 0; endfunction
  function automatic int next_gap(input int n, input int mac_gap);
    int m, top;
    deleted = 0; inserted = 0;
    m = (n + mac_gap) % 4;                       // lanes past lane 0 the next Start would land on
    if (start_any_lane || m == 0) return mac_gap;
    top = dic_max4 ? 4 : 3;
    if (method == 0 && (ipg_min_only || dic + m <= top)) begin deleted = m; dic = dic + m; end
    else begin inserted = 4 - m; if (method == 0) dic = dic - (4 - m); end
    return mac_gap - deleted + inserted;
  endfunction
endmodule
Read included file: eth_xgmii.sv
`timescale 1ns/1ns
// eth_rs: the packet as XGMII characters (9 bits: control flag and octet), four lanes per column, and the
// 66-bit block each pair of columns becomes.
//   clear(), put(c, d), idle(k)
//   lanes            4 for the XGMII and 25GMII (default), 8 for the 64-bit interfaces (XLGMII to 800GMII, P11.18)
//   start_packet()   adds idle until lane 0, then Start (FBh), six preamble octets and the SFD
//   end_packet()     Terminate (FDh)
//   columns(), lane_of(i)   columns of lanes characters; the lane of character i
//   block_info(g)    {valid, sync[1:0], type[7:0]} for characters 8g to 8g+7 (pad the tail with idle first)
// Fault: start_any_lane (Start is not aligned to lane 0).
module eth_rs;
  bit start_any_lane = 0;
  int lanes = 4;
  bit [8:0] ch [0:4095];
  int nch = 0;
  function automatic void clear(); nch = 0; endfunction
  function automatic void put(input bit c, input [7:0] d); ch[nch] = {c, d}; nch++; endfunction
  function automatic void idle(input int k); for (int i = 0; i < k; i++) put(1'b1, 8'h07); endfunction
  function automatic void start_packet();
    if (!start_any_lane) while (nch % lanes != 0) put(1'b1, 8'h07);
    put(1'b1, 8'hfb);
    for (int i = 0; i < 6; i++) put(1'b0, 8'h55);
    put(1'b0, 8'hd5);
  endfunction
  function automatic void end_packet(); put(1'b1, 8'hfd); endfunction
  function automatic void fill_to(input int multiple); while (nch % multiple != 0) put(1'b1, 8'h07); endfunction
  function automatic int columns(); return (nch + lanes - 1) / lanes; endfunction
  function automatic int lane_of(input int i); return i % lanes; endfunction
  function automatic bit is_c(input int i); return ch[i][8]; endfunction
  function automatic bit is_code(input int i, input [7:0] v); return ch[i] == {1'b1, v}; endfunction
  function automatic bit is_plain(input int i);            // a control character with a 7-bit C code
    return is_code(i, 8'h07) || is_code(i, 8'h06) || is_code(i, 8'hfe);
  endfunction
  function automatic bit all_data(input int a, input int b);
    for (int i = a; i <= b; i++) if (is_c(i)) return 0;
    return 1;
  endfunction
  function automatic bit all_plain(input int a, input int b);
    for (int i = a; i <= b; i++) if (!is_plain(i)) return 0;
    return 1;
  endfunction
  function automatic [10:0] block_info(input int g);
    int b; reg [7:0] t; bit ok;
    b = 8 * g; ok = 0; t = 8'h00;
    if (all_data(b, b + 7)) return {1'b1, 2'b01, 8'h00};
    if (all_plain(b, b + 7)) begin ok = 1; t = 8'h1e; end
    else if (is_code(b, 8'hfb) && all_data(b + 1, b + 7)) begin ok = 1; t = 8'h78; end
    else if (all_plain(b, b + 3) && is_code(b + 4, 8'hfb) && all_data(b + 5, b + 7)) begin ok = 1; t = 8'h33; end
    else if (is_code(b, 8'h9c) && all_data(b + 1, b + 3) && is_code(b + 4, 8'hfb) && all_data(b + 5, b + 7)) begin ok = 1; t = 8'h66; end
    else if (is_code(b, 8'h9c) && all_data(b + 1, b + 3) && is_code(b + 4, 8'h9c) && all_data(b + 5, b + 7)) begin ok = 1; t = 8'h55; end
    else if (is_code(b, 8'h9c) && all_data(b + 1, b + 3) && all_plain(b + 4, b + 7)) begin ok = 1; t = 8'h4b; end
    else if (all_plain(b, b + 3) && is_code(b + 4, 8'h9c) && all_data(b + 5, b + 7)) begin ok = 1; t = 8'h2d; end
    else begin
      for (int k = 0; k < 8; k++)
        if (!ok && is_code(b + k, 8'hfd) && (k == 0 || all_data(b, b + k - 1)) && (k == 7 || all_plain(b + k + 1, b + 7))) begin
          ok = 1;
          case (k)
            0: t = 8'h87; 1: t = 8'h99; 2: t = 8'haa; 3: t = 8'hb4;
            4: t = 8'hcc; 5: t = 8'hd2; 6: t = 8'he1; default: t = 8'hff;
          endcase
        end
    end
    return {ok, 2'b10, t};
  endfunction
endmodule

// eth_xgmii_mon: reads XGMII columns as a receiving RS would (46.2, 46.3.3) and reports what it sees.
// A column is {c[3:0], d[31:0]}: lane k is control flag c[k] and octet d[8k+7:8k]; lane 0 comes first.
//   reset(), col(c, d)      one column; col() returns 1 if the column holds anything the monitor flags
//   frames                  Starts seen on lane 0; octets: data octets after the SFD up to the Terminate
//   start_lane, term_lane   where the last Start and Terminate were (-1: not in this column)
//   bad_start               Starts on lanes 1 to 3 (46.3.3.3: the RS must not pass them to the MAC)
//   errors                  Error characters (FEh) seen inside a frame; err_frames: frames that carried one
//   seq_cols                columns holding a Sequence ordered set (9Ch in lane 0, P11.19)
//   last_len                data octets of the last frame, preamble and SFD excluded
module eth_xgmii_mon;
  int frames = 0, octets = 0, bad_start = 0, errors = 0, err_frames = 0, seq_cols = 0, last_len = 0;
  int start_lane = -1, term_lane = -1, in_pkt = 0, pre_left = 0, len = 0;
  bit had_err = 0;
  function automatic void reset();
    frames = 0; octets = 0; bad_start = 0; errors = 0; err_frames = 0; seq_cols = 0; last_len = 0;
    in_pkt = 0; pre_left = 0; len = 0; had_err = 0; start_lane = -1; term_lane = -1;
  endfunction
  function automatic bit col(input [3:0] c, input [31:0] d);
    bit flag; reg [7:0] o;
    flag = 0; start_lane = -1; term_lane = -1;
    if (c[0] && d[7:0] == 8'h9c) seq_cols++;
    for (int k = 0; k < 4; k++) begin
      o = d[8*k +: 8];
      if (c[k] && o == 8'hfb) begin
        start_lane = k;
        if (k != 0) begin bad_start++; flag = 1; end
        else begin in_pkt = 1; pre_left = 7; len = 0; had_err = 0; frames++; end
      end
      else if (in_pkt && c[k] && o == 8'hfd) begin
        term_lane = k; in_pkt = 0; last_len = len;
        if (had_err) err_frames++;
      end
      else if (in_pkt && c[k] && o == 8'hfe) begin errors++; had_err = 1; flag = 1; len++; end
      else if (in_pkt && !c[k]) begin
        if (pre_left > 0) pre_left--;
        else begin len++; octets++; end
      end
    end
    return flag;
  endfunction
endmodule
ConceptWho originates Remote Fault?
ConceptHow many fault sequences of one type set link_fault?
ConceptWhat does an RS send while link_fault is Link Interruption?
ConceptFaults stopped arriving. When does link_fault return to OK?

Common Mistakes

Wrong Take the link down on the first Local Fault set.

The RS needs four of one type, each less than 128 columns after the last.

Fix Count, and act on the 4th.

Wrong Send Idle when Local Fault arrives.

The far end then never learns that its frames are lost.

Fix Send Remote Fault ordered sets on Local Fault.

Wrong Treat a sequence ordered set with a reserved type, such as 04h, as a fault.

Only 01h, 02h and 03h are fault types (Table 46-5).

Fix Ignore reserved types; they are not fault sequences.

Wrong Look for a Sequence character on lane 2.

Sequence is valid on lane 0 only (Table 46-3).

Fix Check lane 0 of each column for 9Ch.

Remember

  • Fault messages are Sequence ordered sets: 9Ch on lane 0, then 00h, 00h and 01h, 02h or 03h.
  • The PHY sends Local Fault; the RS answers with Remote Fault; the other RS then sends Idle.
  • Four sequences of one type set link_fault; 128 quiet columns clear it.
  • OK: frames. Local Fault: Remote Fault. Remote Fault or Link Interruption: Idle.

Practice

Report a problem with this page