PCS Test Patterns and Loopback

Before a link carries frames, someone has to measure it. Meet the test patterns a 10 Gb/s PCS can send, the checkers that count errors, and loopback.

You Will Be Able To

  • Name the test patterns of a 10GBASE-R PCS and what each one is for.
  • Follow the seed schedule of the pseudo-random pattern and its checker.
  • Explain why one bit error gives three flags in the PRBS31 checker.
  • Say what PCS loopback does to the transmit path and to the receive path.
Lesson
P11.25
Time
30 min
Runs on
Your browser
Check
6 questions

G6.10 compared two kinds of pattern checker. A 10 Gb/s PCS has the self-synchronising kind built in. Watch it meet one wrong bit.

One Wrong Bit, Three FlagsA PRBS31 stream with bit 100 flipped on the line. The checker raises its error signal three times.
012bit100128131the wrong bit isthe bit under testused as the bit 28 backused as the bit 31 backerror signal
Scroll horizontally ↔
  1. Cycle 0

    The flipped bit does not fit the 31 bits before it. First flag.

  2. Cycle 1

    Now a good bit is tested, but against the flipped one. Second flag.

  3. Cycle 2

    Three bits later the flipped bit is the oldest one in the test. Third flag.

Bench run of a private PRBS31 checker on the pattern of eth_prbs31. Bits are numbered from 0.

Test Mode

A PCS has two switches: transmit test-pattern mode and receive test-pattern mode (49.2.14.3). MDIO register 3.42 sets them.

In transmit test mode the PCS sends a pattern in place of encoded blocks. In receive test mode it checks one.

PatternMust a PCS have it?What it isUsed for
Square waveyesn ones, then n zeros; n is 4 to 11transmitter tests only
Pseudo-randomyes, with its checkera fixed data pattern through the scrambler, reseeded every 128 blocksreceiver tests, some transmitter tests
PRBS31optional; if so, generator and checkera bit sequence of order 31, invertedtransmitter and receiver tests
PRBS9optionala short bit sequence (Clause 68)some transmitter tests

After IEEE Std 802.3-2022 49.2.8 and 49.2.12, for a PCS that can connect straight to a PMA.

MDIO bitSet to 1
3.42.0the data pattern is zeros (0: two local fault sets)
3.42.1square wave (0: pseudo-random)
3.42.2receive test-pattern mode
3.42.3transmit test-pattern mode
3.42.4PRBS31 on the transmit path
3.42.5PRBS31 on the receive path
3.0.14loopback

After IEEE Std 802.3-2022 45.2.3.19 and 49.2.14.4. Seed A is in registers 3.34 to 3.37, seed B in 3.38 to 3.41, the error counter in 3.43. Bits 3.42.6 (PRBS9) and 3.42.7 (scrambled idle) are not shown.

In receive test mode the BER monitor of P11.24 is switched off (49.2.12). The receive diagram of P11.23 rests in RX_INIT.

So the MAC sees local fault while a test runs. No frame can pass by mistake.

Block lock keeps running. The pseudo-random checker looks at blocks only while lock is true.

The enable bits have a rank (45.2.3.19). Bit 3.42.3 comes before the PRBS31 bit 3.42.4, and both come before PRBS9.

On the receive side, bit 3.42.2 comes before the PRBS31 bit 3.42.5.

The Square Wave

The square wave is the simplest pattern: n ones, then n zeros, for ever (49.2.8). The designer picks n from 4 to 11.

With n = 8 the example printed 111111110000000011111111.

nFrequency at 10.3125 Gb/s
41289.06 MHz
8644.53 MHz
11468.75 MHz

Bench arithmetic: one period is 2n bits.

It gives a clean, steady signal for measuring a transmitter. A receiver is not expected to take it in.

It carries no blocks and no sync headers. So the pattern checkers of this lesson have nothing to check in it.

The Pseudo-Random Pattern

This pattern reuses the scrambler of P11.24. The input is a fixed data pattern, and the scrambler makes it look random.

Every 128 blocks the scrambler is loaded with a seed (49.2.8). Seeds and data pattern let a tester choose the stream it sends.

The Seed ScheduleEvery 128 blocks the scrambler is loaded again. Four loads make one round of 512 blocks.
0123blocks0 to 127128 to 255256 to 383384 to 511scrambler loaded withseed Aseed A invertedseed Bseed B invertedscrambler inputdata patternpattern inverteddata patternpattern invertedchecker mismatch at block0128256384
Scroll horizontally ↔
  1. Cycle 0

    Seed A goes into the 58 stages. The data pattern, zeros or two local fault sets, is scrambled from there.

  2. Cycle 1

    The seed is inverted for this load, and so is the data pattern.

  3. Cycle 2

    Seed B gives the same data a different bit stream.

  4. Cycle 3

    Seed B inverted ends the round. Block 512 starts again with seed A.

After IEEE Std 802.3-2022 49.2.8. The mismatch row is a bench run of a private model: one per load on a clean line.

The optical tests of Clause 52 use one seed per pattern: A, A inverted, and again (52.9.1.1).

Each seed has 58 bits, one per scrambler stage. Every block carries the control sync header, so block lock works as usual.

The data pattern is 64 zeros or two local fault ordered sets. The example prints the second one: 0100000001000055h.

The checker uses the normal lock process and the normal descrambler (49.2.12). It looks at the descrambler output.

A block matches if that output is the data pattern or its inverse. The checker does not need the seeds at all.

Run of 512 blocksChecker mismatch in blocksErrors counted
Zeros pattern, clean line0, 128, 256, 3840
Zeros pattern, one line bit flipped in block 2000, 128, 200, 201, 256, 3842
Local fault pattern, clean line0, 128, 256, 3840

Bench runs of a private generator and checker: P11.25.2 grades both, so their code is not shown. Blocks are numbered from 0 here; P11.25.2 numbers them from 1. Bench choices: seed bit k loads stage Sk, and the checker's first window starts at block 0. The bench checker runs without the block lock process.

Each load breaks one block: the descrambler still holds old line bits. So one mismatch per 128 blocks is expected.

The checker counts in windows of 128 blocks. The first mismatch of a window is free. Each later one adds to the error counter.

The flipped bit cost 2 counts. The descrambler turned it into three wrong bits, and they fell into two blocks.

PRBS31

The optional PRBS31 pattern has no blocks at all. It is one bit sequence that repeats after 2^31 − 1 bits.

The PRBS31 Pattern GeneratorThirty-one stages in a ring. Two of them are XORed to make the next bit.
  • Datapath
  • Storage
  • I/O
  • Data
port (calls out)
The PRBS31 pattern generatorThirty-one stages in a ring. Two of them are XORed to make the next bit. datapath XOR S27 with S30 storage S0 to S27 28 stages storage S28 to S30 3 stages datapath Inverter flips each bit io Pattern out to the PMA new bitshiftS27S30new bit
  1. datapath XORS27 with S30
    • new bit → S0 to S27
    • new bit → Inverter
  2. storage S0 to S2728 stages
    • shift → S28 to S30
    • S27 → XOR
  3. storage S28 to S303 stages
    • S30 → XOR
  4. datapath Inverterflips each bit
    • Pattern out
  5. io Pattern outto the PMA
  1. Make a bit

    S27 XOR S30 is the new bit. It was made from the bits of 28 and 31 steps before.

  2. Shift

    The new bit enters S0. Every other bit moves up one stage.

  3. Invert

    The same new bit leaves through an inverter. So the line carries the sequence upside down.

Read the diagram as text
  • XOR: S27 with S30
  • S0 to S27: 28 stages
  • S28 to S30: 3 stages
  • Inverter: flips each bit
  • Pattern out: to the PMA
  • XOR → S0 to S27: new bit
  • S0 to S27 → S28 to S30: shift
  • S0 to S27 → XOR: S27
  • S28 to S30 → XOR: S30
  • XOR → Inverter: new bit
  • Inverter → Pattern out

After IEEE Std 802.3-2022 Figure 49-9 (redrawn). The polynomial is 1 + x^28 + x^31.

That is 2,147,483,647 bits, about 0.208 s at 10.3125 Gb/s. The register must not start at all zeros.

Started at all ones, the generator sent 28 ones, then 3 zeros, then ones again.

The checker needs no start signal. It keeps the last 31 received bits and tests each new bit against two of them (49.2.12).

Those are the bits that came 28 and 31 bits before. In a clean stream the test always fits.

A checker that started empty flagged 3 of its first 31 bits. After those it was in step.

Stream into the checkerFlagsAt bits
clean pattern, 10,000 bits0none
bit 100 flipped3100, 128, 131
bits 100 and 500 flipped6100, 128, 131, 500, 528, 531
bits 100 and 128 flipped4100, 131, 156, 159
bits 100 and 131 flipped4100, 128, 159, 162
the pattern without its inverter, 1,000 bits1,000every bit

Bench runs of a private PRBS31 checker, after 31 bits to fill it. Bits are numbered from 0.

Look at the row with bit 100. The checker stores every received bit, right or wrong. So a wrong bit is in three tests.

Two wrong bits 28 apart share a test, and there the two cancel. That is why the fourth row has four flags, not six.

The test-pattern error counter adds one per flag. It has 16 bits and stops at 65,535 (49.2.14.2).

So on a link with rare errors, the counter reads about three times the number of wrong bits.

Loopback

Loopback tests the PCS and everything above it without a far end. MDIO bit 3.0.14 turns it on (49.2.14.4).

The PCS still takes data from the XGMII. But it hands that data straight back on its own receive path.

Loopback bitThe receive path decodesThe PMA is sent
1the transmit blockthe word 00FFh, over and over
0the PMA blockthe transmit data

Bench run of the example with eth_66_loop. Bench choice: the loop is taken at the encoded block.

Two more things happen. The PCS sends the word 00FFh to the PMA again and again: a square wave of eight ones and eight zeros.

And it ignores whatever the PMA delivers. A frame from the far end cannot get in during the test.

Try It

The first line is the square wave. The second is the local fault data pattern: block type 55h, then two ordered sets.

Then the PRBS31 generator prints its first 40 bits. The last two lines switch loopback on and off.

The pseudo-random generator and its checker are not in the example. P11.25.2 asks you to build both.

Change tp.sq_n from 8 to 5. Predict the first 24 bits of the square wave before you run it.

RUNIcarus Verilog · in your browser
Edit the code, then run it
Expected: square wave, n = 8: 111111110000000011111111 local fault data pattern: 0100000001000055 PRBS31, register all ones: 1111111111111111111111111111000111111111 loopback on: the receive path gets the transmit block, the PMA gets 00ff loopback off: the receive path gets the PMA block, the PMA gets 1234
Read included file: hs_pkg.sv
`timescale 1ns/1ns
// hs_pkg.sv: shared pure functions, and the bench random generator (read-only).
package hs_pkg;
  // xorshift32 (Marsaglia 2003): a linear generator over GF(2), period 2^32 - 1. A zero state is
  // replaced by 1, because zero maps to itself.
  function automatic [31:0] xs32(input [31:0] s);
    reg [31:0] x;
    x = (s == 32'd0) ? 32'd1 : s;
    x = x ^ (x << 13); x = x ^ (x >> 17); x = x ^ (x << 5);
    return x;
  endfunction
  // A Fibonacci PRBS generator x^n + x^m + 1 (PRBS7: 7,6; PRBS9: 9,5; PRBS15: 15,14; PRBS23: 23,18;
  // PRBS31: 31,28). The output bit is s[n-1]; the next state shifts the feedback into bit 0.
  function automatic [31:0] prbs_next(input [31:0] s, input int n, input int m);
    reg fb;
    fb = s[n-1] ^ s[m-1];
    return ((s << 1) | {31'd0, fb}) & ((n == 32) ? 32'hffffffff : ((32'd1 << n) - 32'd1));
  endfunction
  function automatic int ones(input [63:0] v);
    int n; n = 0;
    for (int i = 0; i < 64; i++) n += v[i];
    return n;
  endfunction
  // GF(16) with x^4 + x + 1, and GF(1024) with x^10 + x^3 + 1: shift-and-add multiply, no tables.
  function automatic [3:0] gf16_mul(input [3:0] a, input [3:0] b);
    reg [3:0] p, x; p = 4'd0; x = a;
    for (int i = 0; i < 4; i++) begin
      if (b[i]) p = p ^ x;
      x = x[3] ? ({x[2:0], 1'b0} ^ 4'b0011) : {x[2:0], 1'b0};
    end
    return p;
  endfunction
  function automatic [3:0] gf16_pow(input int e);   // alpha^e, alpha = x
    reg [3:0] p; int k; p = 4'd1; k = e % 15; if (k < 0) k += 15;
    for (int i = 0; i < k; i++) p = gf16_mul(p, 4'd2);
    return p;
  endfunction
  function automatic int gf16_log(input [3:0] a);   // -1 for 0
    reg [3:0] p; p = 4'd1;
    if (a == 4'd0) return -1;
    for (int i = 0; i < 15; i++) begin if (p == a) return i; p = gf16_mul(p, 4'd2); end
    return -1;
  endfunction
  function automatic [9:0] gf1024_mul(input [9:0] a, input [9:0] b);
    reg [9:0] p, x; p = 10'd0; x = a;
    for (int i = 0; i < 10; i++) begin
      if (b[i]) p = p ^ x;
      x = x[9] ? ({x[8:0], 1'b0} ^ 10'b0000001001) : {x[8:0], 1'b0};
    end
    return p;
  endfunction
  function automatic [9:0] gf1024_pow(input int e);
    reg [9:0] p; int k; p = 10'd1; k = e % 1023; if (k < 0) k += 1023;
    for (int i = 0; i < k; i++) p = gf1024_mul(p, 10'd2);
    return p;
  endfunction
endpackage

// hs_rng: the bench's random numbers. Same seed, same numbers, on every engine.
module hs_rng;
  int unsigned s = 32'h2545f491;
  function automatic void seed(input int unsigned v); s = (v == 0) ? 32'd1 : v; endfunction
  function automatic int unsigned next(); s = hs_pkg::xs32(s); return s; endfunction
  function automatic int below(input int n); s = hs_pkg::xs32(s); return (n <= 0) ? 0 : int'(s % n); endfunction
  function automatic bit bit1(); s = hs_pkg::xs32(s); return s[16]; endfunction
  function automatic bit chance_ppm(input int ppm); s = hs_pkg::xs32(s); return (s % 1000000) < ppm; endfunction
  function automatic [7:0] byte8(); s = hs_pkg::xs32(s); return s[23:16]; endfunction
endmodule
Read included file: hs_code.sv
`timescale 1ns/1ns
// hs_code.sv: line codes, CRCs and scramblers (read-only).

// ---------------------------------------------------------------------------------------------
// hs_8b10b: 8b/10b encoder and decoder with running disparity and the 12 K codes.
// code[9:0] = {a,b,c,d,e,i,f,g,h,j}; bit a (code[9]) goes on the wire first. rd: 0 = RD-, 1 = RD+.
//   encode(d, k, rd_in) -> {rd_out, code[9:0]}            (11 bits)
//   decode(code, rd_in) -> {rd_out, disp_err, code_err, k, d[7:0]}   (12 bits)
//   enc(d, k) / dec(code): the same, with the running disparity kept in rd_tx / rd_rx
// A K request for a byte that is not one of the 12 K codes is encoded as data and counted in bad_k.
// Decoder: code_err = the code is in neither column of the table; disp_err = it is a valid code
// only in the other column. rd_out follows the sub-block rule on the received bits.
// Faults: no_rd (always the RD- column), a7_never (never the alternate D.x.A7),
//         keep_rd_on_unbalanced (the 4b sub-block is chosen with the disparity from before the 6b one),
//         no_balanced_flip (D.07 and D.x.3 keep their RD- form at RD+), dec_no_disp_check.
module hs_8b10b;
  bit no_rd = 0, a7_never = 0, keep_rd_on_unbalanced = 0, no_balanced_flip = 0, dec_no_disp_check = 0;
  bit trace = 0;
  bit rd_tx = 0, rd_rx = 0;
  int bad_k = 0, symbols = 0, code_errs = 0, disp_errs = 0;
  bit last_k = 0, last_code_err = 0, last_disp_err = 0;
  bit valid_m [0:1023]; bit valid_p [0:1023]; bit [8:0] kd [0:1023]; bit built = 0;
  function automatic [5:0] t6(input [4:0] x);   // 5b/6b, RD- column, abcdei
    case (x)
      5'd0: return 6'b100111;  5'd1: return 6'b011101;  5'd2: return 6'b101101;  5'd3: return 6'b110001;
      5'd4: return 6'b110101;  5'd5: return 6'b101001;  5'd6: return 6'b011001;  5'd7: return 6'b111000;
      5'd8: return 6'b111001;  5'd9: return 6'b100101;  5'd10: return 6'b010101; 5'd11: return 6'b110100;
      5'd12: return 6'b001101; 5'd13: return 6'b101100; 5'd14: return 6'b011100; 5'd15: return 6'b010111;
      5'd16: return 6'b011011; 5'd17: return 6'b100011; 5'd18: return 6'b010011; 5'd19: return 6'b110010;
      5'd20: return 6'b001011; 5'd21: return 6'b101010; 5'd22: return 6'b011010; 5'd23: return 6'b111010;
      5'd24: return 6'b110011; 5'd25: return 6'b100110; 5'd26: return 6'b010110; 5'd27: return 6'b110110;
      5'd28: return 6'b001110; 5'd29: return 6'b101110; 5'd30: return 6'b011110; default: return 6'b101011;
    endcase
  endfunction
  function automatic [3:0] t4d(input [2:0] y);  // 3b/4b data, RD- column, fghj (y = 7 is P7)
    case (y)
      3'd0: return 4'b1011; 3'd1: return 4'b1001; 3'd2: return 4'b0101; 3'd3: return 4'b1100;
      3'd4: return 4'b1101; 3'd5: return 4'b1010; 3'd6: return 4'b0110; default: return 4'b1110;
    endcase
  endfunction
  function automatic [3:0] t4k(input [2:0] y);  // 3b/4b for K codes, RD- form before the flip
    case (y)
      3'd0: return 4'b1011; 3'd1: return 4'b0110; 3'd2: return 4'b1010; 3'd3: return 4'b1100;
      3'd4: return 4'b1101; 3'd5: return 4'b0101; 3'd6: return 4'b1001; default: return 4'b0111;
    endcase
  endfunction
  function automatic bit k_ok(input [7:0] d);
    return d[4:0] == 5'd28 || d == 8'hf7 || d == 8'hfb || d == 8'hfd || d == 8'hfe;
  endfunction
  function automatic int n6(input [5:0] v); return v[0] + v[1] + v[2] + v[3] + v[4] + v[5]; endfunction
  function automatic int n4(input [3:0] v); return v[0] + v[1] + v[2] + v[3]; endfunction
  // running disparity at the end of a sub-block (more ones: +; more zeros: -; 000111 and 0011: +; 111000 and 1100: -)
  function automatic bit rd6(input [5:0] v, input bit rd);
    return (n6(v) > 3) ? 1'b1 : (n6(v) < 3) ? 1'b0 : (v == 6'b000111) ? 1'b1 : (v == 6'b111000) ? 1'b0 : rd;
  endfunction
  function automatic bit rd4(input [3:0] v, input bit rd);
    return (n4(v) > 2) ? 1'b1 : (n4(v) < 2) ? 1'b0 : (v == 4'b0011) ? 1'b1 : (v == 4'b1100) ? 1'b0 : rd;
  endfunction
  // faults: [0] no_rd [1] a7_never [2] keep_rd_on_unbalanced [3] no_balanced_flip
  function automatic [10:0] core(input [7:0] d, input bit k, input bit rd_in, input [3:0] f);
    reg [5:0] six; reg [3:0] four; reg rd0, r6, rd1, a7, kk; reg [4:0] x; reg [2:0] y; int o6, o4;
    x = d[4:0]; y = d[7:5]; kk = k && k_ok(d); rd0 = f[0] ? 1'b0 : rd_in;
    six = (kk && x == 5'd28) ? 6'b001111 : t6(x); o6 = n6(six);
    if (rd0 && (o6 != 3 || (six == 6'b111000 && !f[3]))) begin six = ~six; o6 = 6 - o6; end
    r6 = (o6 > 3) ? 1'b1 : (o6 < 3) ? 1'b0 : (six == 6'b000111) ? 1'b1 : (six == 6'b111000) ? 1'b0 : rd0;
    rd1 = f[2] ? rd0 : r6;
    if (kk) begin
      four = t4k(y); if (rd1) four = ~four;
    end else begin
      a7 = (y == 3'd7) && !f[1] && ((!rd1 && (x == 5'd17 || x == 5'd18 || x == 5'd20)) || (rd1 && (x == 5'd11 || x == 5'd13 || x == 5'd14)));
      four = a7 ? 4'b0111 : t4d(y);
      if (rd1 && (n4(four) != 2 || (four == 4'b1100 && !f[3]))) four = ~four;
    end
    o4 = n4(four);
    return {(o4 > 2) ? 1'b1 : (o4 < 2) ? 1'b0 : (four == 4'b0011) ? 1'b1 : (four == 4'b1100) ? 1'b0 : r6, six, four};
  endfunction
  function automatic [10:0] encode(input [7:0] d, input bit k, input bit rd_in);
    if (k && !k_ok(d)) bad_k++;
    return core(d, k, rd_in, {no_balanced_flip, keep_rd_on_unbalanced, a7_never, no_rd});
  endfunction
  function automatic void build();
    reg [10:0] c;
    for (int i = 0; i < 1024; i++) begin valid_m[i] = 0; valid_p[i] = 0; kd[i] = 9'd0; end
    for (int i = 0; i < 268; i++) begin
      reg [7:0] d; reg k;
      if (i < 256) begin d = i[7:0]; k = 0; end
      else begin k = 1; d = (i < 264) ? {3'(i - 256), 5'd28} : (i == 264) ? 8'hf7 : (i == 265) ? 8'hfb : (i == 266) ? 8'hfd : 8'hfe; end
      c = core(d, k, 1'b0, 4'd0); valid_m[c[9:0]] = 1; kd[c[9:0]] = {k, d};
      c = core(d, k, 1'b1, 4'd0); valid_p[c[9:0]] = 1; kd[c[9:0]] = {k, d};
    end
    built = 1;
  endfunction
  function automatic [11:0] decode(input [9:0] code, input bit rd_in);
    reg here, there, ce, de, r;
    if (!built) build();
    here = rd_in ? valid_p[code] : valid_m[code];
    there = rd_in ? valid_m[code] : valid_p[code];
    ce = !(here || there); de = !ce && !here && !dec_no_disp_check;
    r = rd4(code[3:0], rd6(code[9:4], rd_in));
    return {r, de, ce, ce ? 9'd0 : kd[code]};
  endfunction
  function automatic [9:0] enc(input [7:0] d, input bit k);
    reg [10:0] r; r = encode(d, k, rd_tx); rd_tx = r[10];
    if (trace) $display("s%0d TX %s%0d.%0d code=%b rd=%s", symbols, (k && k_ok(d)) ? "K" : "D", d[4:0], d[7:5], r[9:0], r[10] ? "+" : "-");
    symbols++;
    return r[9:0];
  endfunction
  function automatic [8:0] dec(input [9:0] code);
    reg [11:0] r; r = decode(code, rd_rx); rd_rx = r[11];
    last_disp_err = r[10]; last_code_err = r[9]; last_k = r[8];
    if (r[9]) code_errs++; if (r[10]) disp_errs++;
    if (trace && (r[9] || r[10])) $display("RX %b %s", code, r[9] ? "code error" : "disparity error");
    return r[8:0];
  endfunction
  function automatic bit comma7(input [6:0] w); return w == 7'b0011111 || w == 7'b1100000; endfunction
endmodule

// ---------------------------------------------------------------------------------------------
// hs_crc: a CRC of 1 to 32 bits with any polynomial, seed, bit order and final inversion.
// The register shifts left; the polynomial omits the x^width term. The field is sent register bit
// width-1 first (USB 2.0, USB 3.2 and Ethernet all send it this way).
//   use_crc32(), use_crc16_usb2(), use_crc5_usb2(), use_crc16_usb3(): parameter sets
//   reset(), crc_bit(b), crc_byte(v), crc_bits(v, n), field(), field_bit(i), check_value(), crc_residue_ok()
// Faults: msb_first (bytes enter MSB first), no_invert (the field is not complemented), seed_zero.
module hs_crc;
  int width = 32;
  bit [31:0] poly = 32'h04c11db7, seed = 32'hffffffff, residue = 32'hc704dd7b;
  bit lsb_first = 1, invert = 1;
  bit msb_first = 0, no_invert = 0, seed_zero = 0;
  bit [31:0] r = 32'hffffffff;
  function automatic [31:0] mask(); return (width >= 32) ? 32'hffffffff : ((32'd1 << width) - 32'd1); endfunction
  function automatic void reset(); r = seed_zero ? 32'd0 : (seed & mask()); endfunction
  function automatic void set(input int w, input [31:0] p, input [31:0] s, input [31:0] res, input bit lsb, input bit inv);
    width = w; poly = p; seed = s; residue = res; lsb_first = lsb; invert = inv; reset();
  endfunction
  function automatic void use_crc32();      set(32, 32'h04c11db7, 32'hffffffff, 32'hc704dd7b, 1, 1); endfunction
  function automatic void use_crc16_usb2(); set(16, 32'h8005, 32'hffff, 32'h800d, 1, 1); endfunction
  function automatic void use_crc5_usb2();  set(5, 32'h05, 32'h1f, 32'h0c, 1, 1); endfunction
  function automatic void use_crc16_usb3(); set(16, 32'h100b, 32'hffff, 32'hf6aa, 1, 1); endfunction
  function automatic void crc_bit(input bit b);
    reg fb; fb = b ^ r[width - 1];
    r = ((r << 1) ^ (fb ? poly : 32'd0)) & mask();
  endfunction
  function automatic void crc_byte(input [7:0] v);
    for (int i = 0; i < 8; i++) crc_bit(v[(lsb_first ^ msb_first) ? i : 7 - i]);
  endfunction
  function automatic void crc_bits(input [31:0] v, input int n);   // n bits of v, bit 0 first
    for (int i = 0; i < n; i++) crc_bit(v[i]);
  endfunction
  function automatic [31:0] field(); return (invert && !no_invert) ? (~r & mask()) : r; endfunction
  function automatic bit field_bit(input int i); reg [31:0] f; f = field(); return f[width - 1 - i]; endfunction
  // the usual published "check" number: the field with its first-sent bit read as bit 0
  function automatic [31:0] check_value();
    reg [31:0] f, o; f = field(); o = 32'd0;
    for (int i = 0; i < width; i++) o[i] = f[width - 1 - i];
    return lsb_first ? o : f;
  endfunction
  function automatic bit crc_residue_ok(); return r == (residue & mask()); endfunction
endmodule

// ---------------------------------------------------------------------------------------------
// hs_scr: additive (frame-synchronous) and multiplicative (self-synchronising) scramblers.
// poly holds the coefficients: bit k is x^k; the +1 term is always used (taps() sets bit 0); len is the degree.
// Additive: a Galois LFSR. The key bit is s[len-1]; each step shifts left and adds the low terms of
//   the polynomial when the key bit is 1. The data never enters the register.
// Multiplicative: the line bit is the data bit XOR the register bits at the polynomial's terms;
//   the scrambler shifts its own output in, the descrambler shifts the received line bit in.
//   scr_add(len, poly, seed), scr_mul(len, poly), use_usb3_gen1(), use_x58(), use_x23_usb3() (see its note)
//   scr_bit(b), dscr_bit(b), scr_byte(v), dscr_byte(v) (bit 0 first), scr_reset(), scr_hold() (a skip
//   symbol: no step), scr_unscrambled() (a symbol sent in the clear: 8 steps, data untouched)
// Faults: advance_on_skip (scr_hold steps the LFSR 8 times), no_reset (scr_reset does nothing),
//         wrong_tap (the lowest term x^k becomes x^(k+1)), seed_zero (scr_reset loads 0).
module hs_scr;
  bit mult = 0; int len = 16;
  bit [63:0] poly = 64'h10039, seed = 64'hffff;
  bit advance_on_skip = 0, no_reset = 0, wrong_tap = 0, seed_zero = 0;
  bit [63:0] s = 64'hffff;
  int steps = 0;
  function automatic [63:0] lmask(); return (len >= 64) ? 64'hffffffffffffffff : ((64'd1 << len) - 64'd1); endfunction
  function automatic [63:0] taps();
    reg [63:0] p; int k; p = poly | 64'd1; k = 1;
    if (wrong_tap) begin
      while (k < len && !p[k]) k++;
      if (k < len) begin p[k] = 1'b0; p[k + 1] = 1'b1; end
    end
    return p;
  endfunction
  function automatic void load(); s = (seed_zero ? 64'd0 : seed) & lmask(); endfunction
  function automatic void scr_add(input int n, input [63:0] p, input [63:0] sd); mult = 0; len = n; poly = p; seed = sd; s = sd & lmask(); endfunction
  function automatic void scr_mul(input int n, input [63:0] p); mult = 1; len = n; poly = p; seed = 64'd0; s = 64'd0; endfunction
  function automatic void use_usb3_gen1(); scr_add(16, 64'h10039, 64'hffff); endfunction   // x^16 + x^5 + x^4 + x^3 + 1, seed FFFFh
  function automatic void use_x58(); scr_mul(58, (64'd1 << 58) | (64'd1 << 39) | 64'd1); endfunction   // x^58 + x^39 + 1
  // USB 3.2 Gen 2 (§6.3.2.3) polynomial x^23 + x^21 + x^16 + x^8 + x^5 + x^2 + 1 with seed 1DBFBCh. Only the
  // polynomial and seed are the specification's: the register form here is this library's Galois form, and
  // the reset and bypass rules of §6.3.2.3 are not modelled, so do not quote its key stream as USB's.
  function automatic void use_x23_usb3(); scr_add(23, (64'd1 << 23) | (64'd1 << 21) | (64'd1 << 16) | (64'd1 << 8) | (64'd1 << 5) | (64'd1 << 2) | 64'd1, 64'h1dbfbc); endfunction
  function automatic void scr_reset(); if (!no_reset) load(); endfunction
  function automatic bit key(); return s[len - 1]; endfunction
  function automatic void step();
    reg kb; kb = s[len - 1];
    s = ((s << 1) & lmask()) ^ (kb ? (taps() & lmask()) : 64'd0);
    steps++;
  endfunction
  // the XOR of the register bits at the polynomial's terms x^1..x^len (bit k-1 of the register for x^k)
  function automatic bit fbx(input [63:0] st); return ^(st & (taps() >> 1) & lmask()); endfunction
  function automatic bit scr_bit(input bit b);
    reg o;
    if (!mult) begin o = b ^ s[len - 1]; step(); end
    else begin o = b ^ fbx(s); s = ((s << 1) | {63'd0, o}) & lmask(); steps++; end
    return o;
  endfunction
  function automatic bit dscr_bit(input bit b);
    reg o;
    if (!mult) begin o = b ^ s[len - 1]; step(); end
    else begin o = b ^ fbx(s); s = ((s << 1) | {63'd0, b}) & lmask(); steps++; end
    return o;
  endfunction
  function automatic [7:0] scr_byte(input [7:0] v);
    reg [7:0] o; for (int i = 0; i < 8; i++) o[i] = scr_bit(v[i]); return o;
  endfunction
  function automatic [7:0] dscr_byte(input [7:0] v);
    reg [7:0] o; for (int i = 0; i < 8; i++) o[i] = dscr_bit(v[i]); return o;
  endfunction
  // a skip symbol passes unscrambled and the LFSR holds
  function automatic void scr_hold(); if (advance_on_skip && !mult) for (int i = 0; i < 8; i++) step(); endfunction
  // another symbol that is sent unscrambled (a K code other than COM and SKP): the LFSR still steps 8 times
  function automatic void scr_unscrambled(); if (!mult) for (int i = 0; i < 8; i++) step(); endfunction
endmodule
Read included file: eth_mac.sv
`timescale 1ns/1ns
// eth_frame: one MAC frame as octets, its packet as wire bits, and a bit-serial receiver.
//   pay[i]                         client data, set by the bench before build()
//   build(da, sa, lt, len)         destination, source, Length/Type, len data octets, then the FCS -> oct[0..n-1].
//                                  It adds no pad: give it 46 data octets or more. (Padding is P11.2.1's task; the
//                                  pages show the padding MAC's frames as measured tables.)
//   wire_bits(), wire_bit(i)       the packet in transmit order: preamble, SFD, frame
//   rx_start(), rx_bit(b), rx_end()  hunt for the SFD, collect octets, then parse()
//   parse()                        da, sa, lt, is_length, is_type, data_len, fcs_rx, fcs_calc, fcs_ok
// Faults: fcs_msb_first, fcs_no_invert, fcs_covers_preamble, sfd_wrong, msb_first_octets.
module eth_frame;
  localparam int MIN_FRAME = 64, MAX_BASIC = 1518, MAX_QTAG = 1522, MAX_ENVELOPE = 2000;
  bit fcs_msb_first = 0, fcs_no_invert = 0, fcs_covers_preamble = 0, sfd_wrong = 0, msb_first_octets = 0;
  hs_crc crc();
  bit [7:0] pay [0:2047];
  bit [7:0] oct [0:2047];
  int n = 0;
  bit [47:0] da = 0, sa = 0; bit [15:0] lt = 0;
  bit is_length = 0, is_type = 0, fcs_ok = 0;
  int data_len = 0;
  bit [31:0] fcs_rx = 0, fcs_calc = 0;
  // receiver state
  bit in_frame = 0; bit [7:0] hist = 0, cur = 0; int nb = 0, excess = 0, sfd_at = -1, bits_seen = 0;

  // The FCS of oct[0..len-1] as four octets: the first octet sent is in [7:0].
  function automatic [31:0] fcs_of(input int len);
    crc.use_crc32(); crc.msb_first = fcs_msb_first; crc.no_invert = fcs_no_invert; crc.reset();
    if (fcs_covers_preamble) begin
      for (int i = 0; i < 7; i++) crc.crc_byte(8'h55);
      crc.crc_byte(8'hd5);
    end
    for (int i = 0; i < len; i++) crc.crc_byte(oct[i]);
    return crc.check_value();
  endfunction

  function automatic void build(input [47:0] d, input [47:0] s, input [15:0] t, input int len);
    int k; reg [31:0] f;
    k = 0;
    for (int i = 0; i < 6; i++) begin oct[k] = d[47 - 8*i -: 8]; k++; end
    for (int i = 0; i < 6; i++) begin oct[k] = s[47 - 8*i -: 8]; k++; end
    oct[k] = t[15:8]; k++;
    oct[k] = t[7:0]; k++;
    for (int i = 0; i < len; i++) begin oct[k] = pay[i]; k++; end
    f = fcs_of(k);
    for (int i = 0; i < 4; i++) begin oct[k] = f[8*i +: 8]; k++; end
    n = k; excess = 0;
    parse();
  endfunction

  function automatic void parse();
    da = 0; sa = 0; lt = 0; is_length = 0; is_type = 0; fcs_ok = 0; data_len = 0; fcs_rx = 0; fcs_calc = 0;
    if (n >= 14) begin
      da = {oct[0], oct[1], oct[2], oct[3], oct[4], oct[5]};
      sa = {oct[6], oct[7], oct[8], oct[9], oct[10], oct[11]};
      lt = {oct[12], oct[13]};
      is_length = (lt <= 16'd1500);
      is_type = (lt >= 16'd1536);
    end
    if (n >= 18) begin
      fcs_rx = {oct[n-1], oct[n-2], oct[n-3], oct[n-4]};
      fcs_calc = fcs_of(n - 4);
      fcs_ok = (fcs_rx == fcs_calc);
      data_len = is_length ? int'(lt) : n - 18;
    end
  endfunction

  function automatic int wire_bits(); return 8 * (8 + n); endfunction
  function automatic bit wire_bit(input int i);
    int o, b; reg [7:0] v;
    o = i / 8; b = i % 8;
    if (o < 7) v = 8'h55;
    else if (o == 7) v = sfd_wrong ? 8'h55 : 8'hd5;
    else v = oct[o - 8];
    return msb_first_octets ? v[7 - b] : v[b];
  endfunction

  function automatic void rx_start();
    in_frame = 0; hist = 0; cur = 0; nb = 0; n = 0; excess = 0; sfd_at = -1; bits_seen = 0;
  endfunction
  function automatic void rx_bit(input bit b);
    bits_seen++;
    if (!in_frame) begin
      hist = {hist[6:0], b};                      // the oldest bit is hist[7]
      if (hist == 8'b10101011) begin in_frame = 1; sfd_at = bits_seen; end
    end else begin
      if (msb_first_octets) cur[7 - nb] = b; else cur[nb] = b;
      nb++;
      if (nb == 8) begin oct[n] = cur; n++; nb = 0; end
    end
  endfunction
  function automatic void rx_end(); excess = nb; parse(); endfunction
endmodule
// eth_axis: a MAC client bus in the style of AXI4-Stream (IHI 0051B 2.2 handshake, 2.5 TKEEP, 2.6 TLAST, 2.9 TUSER),
// 64 bits wide. Byte 0 of a beat is tdata[7:0] and is first in the frame (AXI4-Stream 2.4.1). Bench conventions,
// not AXI4-Stream's or 802.3's: tkeep is all ones except on the last beat, where it covers bytes 0 to k-1; one tuser
// bit (transfer-based, 2.9.1), read on the last beat only, marks a bad frame (receive) or asks the MAC to abort it
// (transmit).
//   load(n)                  beats for octets oct[0..n-1]: bd[], bk[], bl[], nbeats; bv[] = valid per cycle, ncyc
//   tx_cycles()              the transmit MAC: one beat per cycle once a frame has started. Returns 0 sent,
//                            1 underrun (tvalid fell inside the frame), 2 aborted by tuser. sent_octets, fail_cycle.
// Fault: tvalid_gap (load() leaves cycle 3 of the frame empty: the client was late with a beat).
module eth_axis;
  bit tvalid_gap = 0;
  bit [7:0] oct [0:2047];
  bit [63:0] bd [0:300]; bit [7:0] bk [0:300]; bit bl [0:300]; bit bu [0:300];
  int nbeats = 0;
  bit bv [0:301]; int bix [0:301]; int ncyc = 0;
  int sent_octets = 0, fail_cycle = -1;
  function automatic void load(input int n);
    int b, k;
    nbeats = (n + 7) / 8;
    for (b = 0; b < nbeats; b++) begin
      bd[b] = 64'd0; bk[b] = 8'd0; bl[b] = (b == nbeats - 1); bu[b] = 0;
      for (k = 0; k < 8; k++) if (8*b + k < n) begin bd[b][8*k +: 8] = oct[8*b + k]; bk[b][k] = 1'b1; end
    end
    ncyc = 0;
    for (b = 0; b < nbeats; b++) begin
      if (tvalid_gap && b == 3) begin bv[ncyc] = 0; bix[ncyc] = -1; ncyc++; end
      bv[ncyc] = 1; bix[ncyc] = b; ncyc++;
    end
  endfunction
  function automatic int tx_cycles();
    bit started; started = 0; sent_octets = 0; fail_cycle = -1;
    for (int c = 0; c < ncyc; c++) begin
      if (!bv[c]) begin
        if (started) begin fail_cycle = c; return 1; end
      end else begin
        started = 1;
        if (bl[bix[c]] && bu[bix[c]]) begin fail_cycle = c; return 2; end
        for (int k = 0; k < 8; k++) if (bk[bix[c]][k]) sent_octets++;
      end
    end
    return 0;
  endfunction
endmodule

// eth_pause: the PAUSE function of MAC Control (Annex 31B) at the station that receives PAUSE frames, in octet
// times (one octet time is 8 bit times; a pause quantum is 512 bit times = 64 octet times, 31B.2).
//   reset(), rx_pause(t, q)  a valid PAUSE frame with pause_time q ended at time t: the timer restarts (31B.3.3)
//   may_start(t)             1 when a new data frame may start at time t. A frame already started is never cut
//                            (31B.3.7). react is the bench's reaction time: frames may still start until t + react.
//   paused_until             the time the timer runs out
//   pause_octets(q, o[])     not here: build a PAUSE frame with eth_frame (DA 01-80-C2-00-00-01, 8808h, 0001h, q)
// Faults: pause_ignored, pause_adds_not_overrides (a new frame adds to the timer, and zero does not cancel),
//         slow_reaction (react = 70 quanta, over the 60 allowed at 10 Gb/s), timer_in_bits (q counts bit times).
module eth_pause;
  localparam int QUANTUM = 64;                     // octet times
  bit pause_ignored = 0, pause_adds_not_overrides = 0, slow_reaction = 0, timer_in_bits = 0;
  int react = 0, t_rx = -1, paused_until = 0;
  function automatic void reset(); t_rx = -1; paused_until = 0; endfunction
  function automatic void rx_pause(input int t, input int q);
    int len;
    if (pause_ignored) return;
    len = timer_in_bits ? (q + 7) / 8 : q * QUANTUM;
    if (pause_adds_not_overrides && paused_until > t) paused_until = paused_until + len;
    else paused_until = t + len;
    t_rx = t;
  endfunction
  function automatic bit may_start(input int t);
    int r;
    r = slow_reaction ? 70 * QUANTUM : react;
    if (t_rx < 0) return 1;
    if (t < t_rx + r) return 1;
    return t >= paused_until;
  endfunction
endmodule

// eth_pfc: priority-based flow control (Annex 31D). The frame is 802.3's; holding a priority's queue is the MAC
// Control client's job (IEEE 802.1Q, not held), so the eight timers here are a bench client, in octet times.
//   build(f_oct[], pev, times[])   not here: the bench writes opcode 01-01, the vector and eight times into eth_frame
//   reset(), rx(t, pev, tm[0..7])  for each e[n] = 1 (bit n of the vector's low octet), priority n stops until
//                                  t + 64 * time[n] (hold_end[n]); e[n] = 0 leaves priority n alone; time[n] = 0 releases it
//   blocked(n, t)                  1 while priority n is held
// Fault: pfc_wrong_priority (reads e[n] from bit 7 - n).
module eth_pfc;
  bit pfc_wrong_priority = 0;
  int hold_end [0:7];
  function automatic void reset(); for (int i = 0; i < 8; i++) hold_end[i] = 0; endfunction
  function automatic void rx(input int t, input [15:0] pev, input [127:0] tm);   // tm[16*n +: 16] = time[n]
    bit e;
    for (int n = 0; n < 8; n++) begin
      e = pfc_wrong_priority ? pev[7 - n] : pev[n];
      if (e) hold_end[n] = t + 64 * int'(tm[16*n +: 16]);
    end
  endfunction
  function automatic bit blocked(input int n, input int t); return t < hold_end[n]; endfunction
endmodule

// eth_csma_tx: one half-duplex transmitter (4.2.3.2), one call of tick() per octet time.
//   reset(), load(frame_octets)   a frame of frame_octets (DA to FCS) waits to be sent; it is padded to min_frame
//   tick(carrier)                 carrier: another station's signal is on the wire here now. Returns 1 when the
//                                 station puts an octet (packet or jam) on the wire.
//   plan[i]                       the wait, in slots, after collision i + 1. The bench sets it (default 0). This
//                                 readable station draws nothing and has no attempt limit.
//   state  0 idle, 1 defer, 2 send, 3 jam, 4 backoff, 5 sent (as far as the sender knows)
//   pkt, sent, quiet, left, attempts, late, last_start, last_r
// min_frame is 64 octets; a bench may lower it to show why it is 64. Fault: no_backoff (every wait is 0 slots).
// Deference is a bench simplification: the 12-octet quiet count restarts on any carrier, own or received, and the
// station never starts while carrier is present. 4.2.8 restarts only the first part of the gap, and then transmits
// whatever the carrier.
module eth_csma_tx;
  localparam int SLOT = 64, JAM = 4, GAP = 12, PRE = 8;   // octet times
  bit no_backoff = 0;
  int min_frame = 64;
  int plan [0:63];
  int state = 0, pkt = 0, sent = 0, quiet = GAP, left = 0, attempts = 0, late = 0, last_start = -1, last_r = 0, now = 0;
  function automatic void reset();
    state = 0; pkt = 0; sent = 0; quiet = GAP; left = 0; attempts = 0; late = 0; last_start = -1; last_r = 0; now = 0;
  endfunction
  function automatic void load(input int frame_octets);
    pkt = PRE + frame_octets;
    if (frame_octets < min_frame) pkt = PRE + min_frame;
    state = 1; attempts = 0; sent = 0; late = 0;
  endfunction
  function automatic bit tick(input bit carrier);
    bit on;
    on = 0;
    if (state == 1 && !carrier && quiet >= GAP) begin state = 2; sent = 0; last_start = now; end
    if (state == 2 && carrier) begin
      attempts++; if (sent > SLOT) late++;
      state = 3; left = JAM;
    end
    case (state)
      2: begin sent++; on = 1; if (sent == pkt) state = 5; end
      3: begin
           on = 1; left--;
           if (left == 0) begin
             last_r = no_backoff ? 0 : plan[(attempts - 1) % 64];
             left = SLOT * last_r;
             state = (left == 0) ? 1 : 4;
           end
         end
      4: begin left--; if (left == 0) state = 1; end
      default: ;
    endcase
    quiet = (carrier || on) ? 0 : ((quiet < GAP) ? quiet + 1 : GAP);
    now++;
    return on;
  endfunction
endmodule

// eth_csma: two eth_csma_tx stations, A and B, at the two ends of a wire with a one-way delay of d octet times.
//   run(fa, ready_a, fb, ready_b, tmax)   each station loads its frame (fa, fb octets) at its ready time
//   on_a[t], on_b[t]          what each station put on the wire at time t
//   ev_t[], ev_who[] (0 A, 1 B), ev_kind[], ev_v[], n_ev   the event log:
//     kind 0 starts attempt v; 1 sees a collision after v octets; 2 jam over, backs off v slots;
//     3 last octet sent (v = octets); 4 gives up after v attempts
//   delivered(i)              1 when station i's last attempt reached the far end with no overlap there
//   a.plan[], b.plan[], a.no_backoff, b.no_backoff, a.min_frame, b.min_frame: the stations' settings
module eth_csma;
  eth_csma_tx a(); eth_csma_tx b();
  int d = 10, n_ev = 0, tend = 0;
  bit on_a [0:16383]; bit on_b [0:16383];
  int ev_t [0:255]; int ev_who [0:255]; int ev_kind [0:255]; int ev_v [0:255];
  function automatic void log_ev(input int t, input int who, input int kind, input int v);
    if (n_ev < 256) begin ev_t[n_ev] = t; ev_who[n_ev] = who; ev_kind[n_ev] = kind; ev_v[n_ev] = v; n_ev++; end
  endfunction
  function automatic void note(input int t, input int who, input int s0, input int s1, input int sent0, input int att, input int r, input int sent1);
    if (s0 != 2 && s1 == 2) log_ev(t, who, 0, att + 1);
    if (s0 == 2 && (s1 == 3 || s1 == 4)) log_ev(t, who, 1, sent0);
    if (s0 == 3 && (s1 == 4 || s1 == 1)) log_ev(t, who, 2, r);
    if (s0 != 5 && s1 == 5) log_ev(t, who, 3, sent1);
    if (s0 != 6 && s1 == 6) log_ev(t, who, 4, att);
  endfunction
  function automatic void run(input int fa, input int ready_a, input int fb, input int ready_b, input int tmax);
    bit ca, cb; int sa, sb, xa, xb;
    a.reset(); b.reset(); n_ev = 0; tend = tmax;
    for (int t = 0; t < tmax; t++) begin
      if (t == ready_a) a.load(fa);
      if (t == ready_b) b.load(fb);
      ca = (t >= d) ? on_b[t - d] : 1'b0;
      cb = (t >= d) ? on_a[t - d] : 1'b0;
      sa = a.state; sb = b.state; xa = a.sent; xb = b.sent;
      on_a[t] = a.tick(ca);
      on_b[t] = b.tick(cb);
      note(t, 0, sa, a.state, xa, a.attempts, a.last_r, a.sent);
      note(t, 1, sb, b.state, xb, b.attempts, b.last_r, b.sent);
    end
  endfunction
  function automatic bit delivered(input int i);
    int s, p, u;
    if (i == 0 && a.state != 5) return 0;
    if (i == 1 && b.state != 5) return 0;
    s = (i == 0) ? a.last_start : b.last_start;
    p = (i == 0) ? a.pkt : b.pkt;
    for (int t = s; t < s + p; t++) begin
      u = t + d;
      if (u < tend && ((i == 0) ? on_b[u] : on_a[u])) return 0;
    end
    return 1;
  endfunction
endmodule

// eth_gap: how long the gap before the next Start is on a 4-lane XGMII, where Start must sit on lane 0
// (46.3.1.4). A gap counts every character from the Terminate to the last idle before Start. A packet is
// 8 + n characters (Start, six preamble octets, SFD, an n-octet frame) and starts on lane 0.
//   reset()                     DIC = 0 (the count is reset only at initialisation)
//   method                      0 deficit idle count, 1 always insert (both allowed by 46.3.1.4)
//   next_gap(n, mac_gap)        the gap after an n-octet frame when the MAC asks for mac_gap (12 or more)
//   deleted, inserted, dic      what the last call did, and the count after it
// Faults: ipg_min_only (always deletes, ignoring the bound), dic_max4 (bounds the count at 4, not 3),
//         start_any_lane (no alignment: the gap is always mac_gap).
module eth_gap;
  bit ipg_min_only = 0, dic_max4 = 0, start_any_lane = 0;
  int method = 0, dic = 0, deleted = 0, inserted = 0;
  function automatic void reset(); dic = 0; deleted = 0; inserted = 0; endfunction
  function automatic int next_gap(input int n, input int mac_gap);
    int m, top;
    deleted = 0; inserted = 0;
    m = (n + mac_gap) % 4;                       // lanes past lane 0 the next Start would land on
    if (start_any_lane || m == 0) return mac_gap;
    top = dic_max4 ? 4 : 3;
    if (method == 0 && (ipg_min_only || dic + m <= top)) begin deleted = m; dic = dic + m; end
    else begin inserted = 4 - m; if (method == 0) dic = dic - (4 - m); end
    return mac_gap - deleted + inserted;
  endfunction
endmodule
Read included file: eth_pcs.sv
`timescale 1ns/1ns
// eth_pcs.sv: the 1000BASE-X PCS, transmit side and synchronization (read-only). It sits on hs_8b10b (hs_code.sv).

// eth_1000x: the transmit ordered-set layer (36.2.4). The stream is kept as {k, d} and as ten coded bits.
//   clear()            empty stream, running disparity negative
//   idle(k)            k idle ordered sets. Each tests the running disparity first (Figure 36-6):
//                      positive -> /I1/ (K28.5 D5.6), negative -> /I2/ (K28.5 D16.2)
//   cfg(word, k)       k configuration ordered sets, /C1/ and /C2/ in turn: K28.5, D21.5 or D2.2, word[7:0], word[15:8]
//   start_packet()     /S/ in place of the first preamble octet, then six 55h and D5h
//   data(d)            one data code-group
//   end_packet()       /T/ /R/, and one more /R/ when the first /R/ went out on an even position
//   err()              /V/
//   put(k, d)          any code-group
//   n                  code-groups so far; code-group i is even-numbered when i is even
//   sym[i] = {k, d};  code[i] = abcdei fghj, bit a (code[i][9]) is sent first;  rdb[i] = running disparity before i
//   is_k(i, d), comma_plus(), comma_minus()
// Fault: idle_wrong_disparity (every idle is /I2/, so a positive running disparity is never corrected).
module eth_1000x;
  bit idle_wrong_disparity = 0;
  hs_8b10b c8();
  bit [8:0] sym [0:8191]; bit [9:0] code [0:8191]; bit rdb [0:8191];
  int n = 0; bit c2 = 0;
  function automatic void clear(); n = 0; c2 = 0; c8.rd_tx = 0; endfunction
  function automatic void put(input bit k, input [7:0] d);
    sym[n] = {k, d}; rdb[n] = c8.rd_tx; code[n] = c8.enc(d, k); n++;
  endfunction
  function automatic void idle(input int k);
    bit positive;
    for (int i = 0; i < k; i++) begin
      positive = c8.rd_tx && !idle_wrong_disparity;
      put(1'b1, 8'hbc);                                // K28.5
      put(1'b0, positive ? 8'hc5 : 8'h50);             // D5.6 or D16.2
    end
  endfunction
  function automatic void cfg(input [15:0] word, input int k);
    for (int i = 0; i < k; i++) begin
      put(1'b1, 8'hbc);
      put(1'b0, c2 ? 8'h42 : 8'hb5);                   // D2.2 or D21.5
      put(1'b0, word[7:0]); put(1'b0, word[15:8]);
      c2 = !c2;
    end
  endfunction
  function automatic void data(input [7:0] d); put(1'b0, d); endfunction
  function automatic void start_packet();
    put(1'b1, 8'hfb);                                  // /S/ = K27.7
    for (int i = 0; i < 6; i++) put(1'b0, 8'h55);
    put(1'b0, 8'hd5);
  endfunction
  function automatic void end_packet();
    put(1'b1, 8'hfd);                                  // /T/ = K29.7
    put(1'b1, 8'hf7);                                  // /R/ = K23.7
    if (n % 2 != 0) put(1'b1, 8'hf7);                  // that /R/ was even-numbered: one more
  endfunction
  function automatic void err(); put(1'b1, 8'hfe); endfunction     // /V/ = K30.7
  function automatic bit is_k(input int i, input [7:0] d); return sym[i] == {1'b1, d}; endfunction
  function automatic int comma_plus();
    int c; c = 0;
    for (int i = 0; i < n; i++) if (code[i][9:3] == 7'b0011111) c++;
    return c;
  endfunction
  function automatic int comma_minus();
    int c; c = 0;
    for (int i = 0; i < n; i++) if (code[i][9:3] == 7'b1100000) c++;
    return c;
  endfunction
endmodule

// eth_1000x_sync: the synchronization process of Figure 36-9, one call of rx() per ten-bit code-group.
//   reset()            LOSS_OF_SYNC
//   rx(code)           takes one code-group; returns sync_status (1 = OK)
//   state              0 LOSS_OF_SYNC, 1 COMMA_DETECT_1, 2 ACQUIRE_SYNC_1, 3 COMMA_DETECT_2, 4 ACQUIRE_SYNC_2,
//                      5 COMMA_DETECT_3, 6 SYNC_ACQUIRED_1, 7 SYNC_ACQUIRED_2, 8 SYNC_ACQUIRED_2A,
//                      9 SYNC_ACQUIRED_3, 10 SYNC_ACQUIRED_3A, 11 SYNC_ACQUIRED_4, 12 SYNC_ACQUIRED_4A
//   even               the code-group just taken was even-numbered
//   good_cgs, bad_seen (every bad code-group since reset), k, d (the last decode)
// A code-group is bad when it is invalid, or when it holds a comma and is odd-numbered (36.2.5.1.3).
// Bench choices: in LOSS_OF_SYNC the decoder takes its running disparity from the comma it finds; an invalid
// code-group leaves the decoder's running disparity as the received bits set it.
module eth_1000x_sync;
  hs_8b10b c8();
  int state = 0, good_cgs = 0, bad_seen = 0;
  bit even = 0, sync = 0, rd = 0, k = 0; bit [7:0] d = 0;
  function automatic void reset(); state = 0; good_cgs = 0; bad_seen = 0; even = 0; sync = 0; rd = 0; endfunction
  function automatic bit rx(input [9:0] code);
    reg [11:0] r; bit invalid, comma, is_d, bad;
    comma = code[9:3] == 7'b0011111 || code[9:3] == 7'b1100000;
    if (state == 0 && comma) rd = (code[9:3] == 7'b1100000);
    r = c8.decode(code, rd);                           // {rd_out, disp_err, code_err, k, d}
    rd = r[11]; k = r[8]; d = r[7:0];
    invalid = r[10] || r[9];
    is_d = !invalid && !r[8];
    bad = invalid || (comma && even);                  // even: the one before was even, so this one is odd
    if (bad && state != 0) bad_seen++;
    case (state)
      0: begin if (comma) begin state = 1; even = 1; end else even = !even; end
      1, 3, 5: begin even = 0; state = is_d ? state + 1 : 0; end
      2, 4: begin
        if (bad) state = 0;
        else if (comma) begin state = state + 1; even = 1; end
        else even = !even;
      end
      6: begin even = !even; if (bad) begin state = 7; good_cgs = 0; end end
      7, 9, 11: begin
        even = !even;
        if (bad) begin state = (state == 11) ? 0 : state + 2; good_cgs = 0; end
        else begin state = state + 1; good_cgs = 1; end
      end
      default: begin                                   // 8, 10, 12: counting good code-groups
        even = !even;
        if (bad) begin state = (state == 12) ? 0 : state + 1; good_cgs = 0; end
        else if (good_cgs == 3) begin state = (state == 8) ? 6 : state - 3; good_cgs = 0; end
        else good_cgs++;
      end
    endcase
    sync = state >= 6;
    return sync;
  endfunction
endmodule

// ---- 10GBASE-R and 25GBASE-R: 64B/66B blocks (Clause 49; Clause 107 uses the same code) ----
// Eight XGMII characters are one vector raw[71:0] (49.2.13.2.2): raw[k] is the control flag of character k,
// raw[8 + 8*k +: 8] its octet. A block is blk[65:0]; bit 0 is sent first. blk[1:0] is the sync header,
// blk[9:2] the block type field of a control block, the rest the payload (Figure 49-7).

// eth_66: the control blocks that hold no Start, no Terminate and no frame data.
//   c_code(x)       Table 49-1: the 7-bit C code of XGMII control code x; 7Fh if x is not in the table
//   enc_ctrl(raw)   {ok, blk}: block type 1Eh (eight control characters), 2Dh (four, then an ordered set),
//                   4Bh (an ordered set, then four) or 55h (two ordered sets); ok = 0 if raw is none of these.
//                   It only lays out the fields. Whether the vector may be sent is the transmit process's
//                   decision (eth_66_tx).
//   on_wire(blk)    the 66 bits as text in the order they are sent: sync, block type, payload
//   ham(a, b)       how many bits differ between two block type values
// Fault: wrong_block_type (types 2Dh and 4Bh are swapped).
module eth_66;
  bit wrong_block_type = 0;
  function automatic [6:0] c_code(input [7:0] x);
    case (x)
      8'h07: return 7'h00;                             // idle
      8'h06: return 7'h06;                             // low power idle
      8'hfe: return 7'h1e;                             // error
      8'h1c: return 7'h2d;                             // the six reserved characters
      8'h3c: return 7'h33;
      8'h7c: return 7'h4b;
      8'hbc: return 7'h55;
      8'hdc: return 7'h66;
      8'hf7: return 7'h78;
      default: return 7'h7f;
    endcase
  endfunction
  function automatic [7:0] ch(input [71:0] raw, input int k); return raw[8 + 8*k +: 8]; endfunction
  // characters k to k+3 are a sequence ordered set: 9Ch with its flag, then three data octets
  function automatic bit is_q(input [71:0] raw, input int k);
    return raw[k] && ch(raw, k) == 8'h9c && !raw[k + 1] && !raw[k + 2] && !raw[k + 3];
  endfunction
  // characters k to k+3 are control characters with a C code
  function automatic bit is_c4(input [71:0] raw, input int k);
    for (int j = k; j < k + 4; j++) if (!raw[j] || c_code(ch(raw, j)) == 7'h7f) return 0;
    return 1;
  endfunction
  function automatic [66:0] enc_ctrl(input [71:0] raw);
    reg [65:0] b; bit q0, q4, c0, c4;
    b = 66'd0;
    b[1:0] = 2'b01;                                    // sync header "10": bit 0, sent first, is 1
    q0 = is_q(raw, 0); q4 = is_q(raw, 4); c0 = is_c4(raw, 0); c4 = is_c4(raw, 4);
    if (c0 && c4) b[9:2] = 8'h1e;
    else if (c0 && q4) b[9:2] = wrong_block_type ? 8'h4b : 8'h2d;
    else if (q0 && c4) b[9:2] = wrong_block_type ? 8'h2d : 8'h4b;
    else if (q0 && q4) b[9:2] = 8'h55;
    else return 67'd0;
    if (c0) for (int k = 0; k < 4; k++) b[10 + 7*k +: 7] = c_code(ch(raw, k));
    else begin b[33:10] = raw[39:16]; b[37:34] = 4'h0; end     // D1 to D3, then the O code of the sequence set
    if (c4) for (int k = 4; k < 8; k++) b[10 + 7*k +: 7] = c_code(ch(raw, k));
    else begin b[41:38] = 4'h0; b[65:42] = raw[71:48]; end     // the O code, then D5 to D7
    return {1'b1, b};
  endfunction
  function automatic string on_wire(input [65:0] blk);
    string s;
    s = "";
    for (int i = 0; i < 66; i++) begin
      if (i == 2 || i == 10) s = {s, " "};
      s = {s, blk[i] ? "1" : "0"};
    end
    return s;
  endfunction
  function automatic int ham(input [7:0] a, input [7:0] b);
    int n; reg [7:0] x;
    x = a ^ b; n = 0;
    for (int i = 0; i < 8; i++) if (x[i]) n++;
    return n;
  endfunction
endmodule

// eth_66_tx: the transmit state diagram (Figure 49-16) without the EEE state. One call per vector.
//   step(t)   t is the T_TYPE of the vector: 0 C (control), 1 S (start), 2 T (terminate), 3 D (data), 4 E (none of these).
//             Returns 1 if the vector is encoded and sent, 0 if the error block goes out in its place.
//   state     0 TX_INIT, 1 TX_C, 2 TX_D, 3 TX_T, 4 TX_E
module eth_66_tx;
  int state = 0;
  function automatic void reset(); state = 0; endfunction
  function automatic bit step(input int t);
    case (state)
      0, 1, 3: state = (t == 0) ? 1 : (t == 1) ? 2 : 4;                    // TX_INIT, TX_C, TX_T: only C or S may follow
      2: state = (t == 3) ? 2 : (t == 2) ? 3 : 4;                          // TX_D: only D or T may follow
      default: state = (t == 2) ? 3 : (t == 3) ? 2 : (t == 0) ? 1 : 4;     // TX_E: T, D or C leave it
    endcase
    return state != 4;
  endfunction
endmodule

// eth_66_comp: clock compensation on XGMII columns (49.2.4.7, 49.2.4.10). Call once per column, in order.
// A column is {c[3:0], d[31:0]}: lane k is flag c[k] and octet d[8k+7:8k].
//   can_delete(c, d)   1 if this column may be dropped: four idles that hold none of the first four characters
//                      after a Terminate, or the second of two consecutive sequence ordered sets
//   can_insert(c, d)   1 if an idle column may be added after this one: it is idle or an ordered set
module eth_66_comp;
  bit guard = 0, prev_seq = 0;
  function automatic void reset(); guard = 0; prev_seq = 0; endfunction
  function automatic bit is_seq(input [3:0] c, input [31:0] d); return c == 4'b0001 && d[7:0] == 8'h9c; endfunction
  function automatic bit is_idle(input [3:0] c, input [31:0] d); return c == 4'b1111 && d == 32'h07070707; endfunction
  function automatic bit can_delete(input [3:0] c, input [31:0] d);
    bit ok, has_t;
    has_t = 0;
    for (int k = 0; k < 4; k++) if (c[k] && d[8*k +: 8] == 8'hfd) has_t = 1;
    ok = (is_idle(c, d) && !guard) || (is_seq(c, d) && prev_seq);
    guard = has_t;                                     // the next column holds some of the four characters after /T/
    prev_seq = is_seq(c, d) && !ok;                    // only one of the two
    return ok;
  endfunction
  function automatic bit can_insert(input [3:0] c, input [31:0] d); return is_idle(c, d) || is_seq(c, d); endfunction
endmodule

// eth_66_scr: the scrambler and the descrambler of 10GBASE-R (49.2.6, 49.2.10; Figures 49-8 and 49-10).
// The register is s[57:0]: stage S0 is s[0] and holds the newest line bit. Use one instance to scramble and
// another to descramble.
//   scr_bit(b)       one payload bit in, one line bit out: b XOR S38 XOR S57. The line bit shifts into S0.
//   dscr_bit(b)      one line bit in, one payload bit out: the same XOR. The received bit shifts into S0.
//   scramble(blk)    a whole block: bits 1:0 (the sync header) pass, bits 2 to 65 are scrambled in that order
//   descramble(blk)  the reverse
//   load(v)          sets the register (the standard asks for no start value)
// Fault: scrambles_header (the two sync header bits go through the scrambler too).
module eth_66_scr;
  bit [57:0] s = 58'd0;
  bit scrambles_header = 0;
  function automatic void load(input [57:0] v); s = v; endfunction
  function automatic bit scr_bit(input bit b);
    bit o; o = b ^ s[38] ^ s[57]; s = {s[56:0], o}; return o;
  endfunction
  function automatic bit dscr_bit(input bit b);
    bit o; o = b ^ s[38] ^ s[57]; s = {s[56:0], b}; return o;
  endfunction
  function automatic [65:0] scramble(input [65:0] blk);
    reg [65:0] o; o = blk;
    for (int i = scrambles_header ? 0 : 2; i < 66; i++) o[i] = scr_bit(blk[i]);
    return o;
  endfunction
  function automatic [65:0] descramble(input [65:0] blk);
    reg [65:0] o; o = blk;
    for (int i = 2; i < 66; i++) o[i] = dscr_bit(blk[i]);
    return o;
  endfunction
endmodule

// eth_prbs31: the PRBS31 pattern generator (49.2.8, Figure 49-9). The register is s[30:0], stage S0 is s[0].
//   gen_bit()   the next pattern bit: S27 XOR S30 shifts into S0, and the output is that bit inverted
// The register must not be all zeros: it would stay there. The checker is not in this file.
module eth_prbs31;
  bit [30:0] s = 31'h7fffffff;
  function automatic bit gen_bit();
    bit f; f = s[27] ^ s[30]; s = {s[29:0], f}; return !f;
  endfunction
endmodule

// eth_66_test: the square wave of 49.2.8 and the two data patterns of the pseudo-random test pattern.
//   sq_bit()        square wave: sq_n ones, then sq_n zeros (sq_n may be 4 to 11)
//   pattern()       the 64-bit data pattern: zeros, or the payload of a block with two local fault sets (lf_pattern)
// The pseudo-random pattern generator and its checker (49.2.8, 49.2.12) are not in this file.
module eth_66_test;
  eth_66 code();
  bit lf_pattern = 0;
  int sq_n = 8, sq_k = 0;
  function automatic void restart(); sq_k = 0; endfunction
  function automatic bit sq_bit();
    bit b; b = (sq_k < sq_n); sq_k = (sq_k + 1) % (2 * sq_n); return b;
  endfunction
  function automatic [63:0] pattern();
    reg [66:0] r;
    if (!lf_pattern) return 64'd0;
    r = code.enc_ctrl({64'h0100009c_0100009c, 8'h11}); return r[65:2];
  endfunction
endmodule

// eth_66_loop: PCS loopback (49.2.14.4), switched by MDIO bit 3.0.14.
//   rx_block(from_tx, from_pma)   what the receive path decodes: its own transmit block when loopback is 1
//   pma_word(w)                   what goes to the PMA: the word 00FFh when loopback is 1, else w
module eth_66_loop;
  bit loopback = 0;
  function automatic [65:0] rx_block(input [65:0] from_tx, input [65:0] from_pma); return loopback ? from_tx : from_pma; endfunction
  function automatic [15:0] pma_word(input [15:0] w); return loopback ? 16'h00ff : w; endfunction
endmodule

Check Yourself

Predict the outputThe program sets the square wave to n = 11 and prints bits 20 to 31, counted from 0. What does it print?
`timescale 1ns/1ns
module tb;
  eth_66_test tp(); string s; bit b;
  initial begin
    tp.sq_n = 11; s = "";
    for (int i = 0; i < 32; i++) begin
      b = tp.sq_bit();
      if (i >= 20) s = {s, b ? "1" : "0"};
    end
    $display("square wave, bits 20 to 31: %s", s);
    $finish;
  end
endmodule
Read included file: hs_pkg.sv
`timescale 1ns/1ns
// hs_pkg.sv: shared pure functions, and the bench random generator (read-only).
package hs_pkg;
  // xorshift32 (Marsaglia 2003): a linear generator over GF(2), period 2^32 - 1. A zero state is
  // replaced by 1, because zero maps to itself.
  function automatic [31:0] xs32(input [31:0] s);
    reg [31:0] x;
    x = (s == 32'd0) ? 32'd1 : s;
    x = x ^ (x << 13); x = x ^ (x >> 17); x = x ^ (x << 5);
    return x;
  endfunction
  // A Fibonacci PRBS generator x^n + x^m + 1 (PRBS7: 7,6; PRBS9: 9,5; PRBS15: 15,14; PRBS23: 23,18;
  // PRBS31: 31,28). The output bit is s[n-1]; the next state shifts the feedback into bit 0.
  function automatic [31:0] prbs_next(input [31:0] s, input int n, input int m);
    reg fb;
    fb = s[n-1] ^ s[m-1];
    return ((s << 1) | {31'd0, fb}) & ((n == 32) ? 32'hffffffff : ((32'd1 << n) - 32'd1));
  endfunction
  function automatic int ones(input [63:0] v);
    int n; n = 0;
    for (int i = 0; i < 64; i++) n += v[i];
    return n;
  endfunction
  // GF(16) with x^4 + x + 1, and GF(1024) with x^10 + x^3 + 1: shift-and-add multiply, no tables.
  function automatic [3:0] gf16_mul(input [3:0] a, input [3:0] b);
    reg [3:0] p, x; p = 4'd0; x = a;
    for (int i = 0; i < 4; i++) begin
      if (b[i]) p = p ^ x;
      x = x[3] ? ({x[2:0], 1'b0} ^ 4'b0011) : {x[2:0], 1'b0};
    end
    return p;
  endfunction
  function automatic [3:0] gf16_pow(input int e);   // alpha^e, alpha = x
    reg [3:0] p; int k; p = 4'd1; k = e % 15; if (k < 0) k += 15;
    for (int i = 0; i < k; i++) p = gf16_mul(p, 4'd2);
    return p;
  endfunction
  function automatic int gf16_log(input [3:0] a);   // -1 for 0
    reg [3:0] p; p = 4'd1;
    if (a == 4'd0) return -1;
    for (int i = 0; i < 15; i++) begin if (p == a) return i; p = gf16_mul(p, 4'd2); end
    return -1;
  endfunction
  function automatic [9:0] gf1024_mul(input [9:0] a, input [9:0] b);
    reg [9:0] p, x; p = 10'd0; x = a;
    for (int i = 0; i < 10; i++) begin
      if (b[i]) p = p ^ x;
      x = x[9] ? ({x[8:0], 1'b0} ^ 10'b0000001001) : {x[8:0], 1'b0};
    end
    return p;
  endfunction
  function automatic [9:0] gf1024_pow(input int e);
    reg [9:0] p; int k; p = 10'd1; k = e % 1023; if (k < 0) k += 1023;
    for (int i = 0; i < k; i++) p = gf1024_mul(p, 10'd2);
    return p;
  endfunction
endpackage

// hs_rng: the bench's random numbers. Same seed, same numbers, on every engine.
module hs_rng;
  int unsigned s = 32'h2545f491;
  function automatic void seed(input int unsigned v); s = (v == 0) ? 32'd1 : v; endfunction
  function automatic int unsigned next(); s = hs_pkg::xs32(s); return s; endfunction
  function automatic int below(input int n); s = hs_pkg::xs32(s); return (n <= 0) ? 0 : int'(s % n); endfunction
  function automatic bit bit1(); s = hs_pkg::xs32(s); return s[16]; endfunction
  function automatic bit chance_ppm(input int ppm); s = hs_pkg::xs32(s); return (s % 1000000) < ppm; endfunction
  function automatic [7:0] byte8(); s = hs_pkg::xs32(s); return s[23:16]; endfunction
endmodule
Read included file: hs_code.sv
`timescale 1ns/1ns
// hs_code.sv: line codes, CRCs and scramblers (read-only).

// ---------------------------------------------------------------------------------------------
// hs_8b10b: 8b/10b encoder and decoder with running disparity and the 12 K codes.
// code[9:0] = {a,b,c,d,e,i,f,g,h,j}; bit a (code[9]) goes on the wire first. rd: 0 = RD-, 1 = RD+.
//   encode(d, k, rd_in) -> {rd_out, code[9:0]}            (11 bits)
//   decode(code, rd_in) -> {rd_out, disp_err, code_err, k, d[7:0]}   (12 bits)
//   enc(d, k) / dec(code): the same, with the running disparity kept in rd_tx / rd_rx
// A K request for a byte that is not one of the 12 K codes is encoded as data and counted in bad_k.
// Decoder: code_err = the code is in neither column of the table; disp_err = it is a valid code
// only in the other column. rd_out follows the sub-block rule on the received bits.
// Faults: no_rd (always the RD- column), a7_never (never the alternate D.x.A7),
//         keep_rd_on_unbalanced (the 4b sub-block is chosen with the disparity from before the 6b one),
//         no_balanced_flip (D.07 and D.x.3 keep their RD- form at RD+), dec_no_disp_check.
module hs_8b10b;
  bit no_rd = 0, a7_never = 0, keep_rd_on_unbalanced = 0, no_balanced_flip = 0, dec_no_disp_check = 0;
  bit trace = 0;
  bit rd_tx = 0, rd_rx = 0;
  int bad_k = 0, symbols = 0, code_errs = 0, disp_errs = 0;
  bit last_k = 0, last_code_err = 0, last_disp_err = 0;
  bit valid_m [0:1023]; bit valid_p [0:1023]; bit [8:0] kd [0:1023]; bit built = 0;
  function automatic [5:0] t6(input [4:0] x);   // 5b/6b, RD- column, abcdei
    case (x)
      5'd0: return 6'b100111;  5'd1: return 6'b011101;  5'd2: return 6'b101101;  5'd3: return 6'b110001;
      5'd4: return 6'b110101;  5'd5: return 6'b101001;  5'd6: return 6'b011001;  5'd7: return 6'b111000;
      5'd8: return 6'b111001;  5'd9: return 6'b100101;  5'd10: return 6'b010101; 5'd11: return 6'b110100;
      5'd12: return 6'b001101; 5'd13: return 6'b101100; 5'd14: return 6'b011100; 5'd15: return 6'b010111;
      5'd16: return 6'b011011; 5'd17: return 6'b100011; 5'd18: return 6'b010011; 5'd19: return 6'b110010;
      5'd20: return 6'b001011; 5'd21: return 6'b101010; 5'd22: return 6'b011010; 5'd23: return 6'b111010;
      5'd24: return 6'b110011; 5'd25: return 6'b100110; 5'd26: return 6'b010110; 5'd27: return 6'b110110;
      5'd28: return 6'b001110; 5'd29: return 6'b101110; 5'd30: return 6'b011110; default: return 6'b101011;
    endcase
  endfunction
  function automatic [3:0] t4d(input [2:0] y);  // 3b/4b data, RD- column, fghj (y = 7 is P7)
    case (y)
      3'd0: return 4'b1011; 3'd1: return 4'b1001; 3'd2: return 4'b0101; 3'd3: return 4'b1100;
      3'd4: return 4'b1101; 3'd5: return 4'b1010; 3'd6: return 4'b0110; default: return 4'b1110;
    endcase
  endfunction
  function automatic [3:0] t4k(input [2:0] y);  // 3b/4b for K codes, RD- form before the flip
    case (y)
      3'd0: return 4'b1011; 3'd1: return 4'b0110; 3'd2: return 4'b1010; 3'd3: return 4'b1100;
      3'd4: return 4'b1101; 3'd5: return 4'b0101; 3'd6: return 4'b1001; default: return 4'b0111;
    endcase
  endfunction
  function automatic bit k_ok(input [7:0] d);
    return d[4:0] == 5'd28 || d == 8'hf7 || d == 8'hfb || d == 8'hfd || d == 8'hfe;
  endfunction
  function automatic int n6(input [5:0] v); return v[0] + v[1] + v[2] + v[3] + v[4] + v[5]; endfunction
  function automatic int n4(input [3:0] v); return v[0] + v[1] + v[2] + v[3]; endfunction
  // running disparity at the end of a sub-block (more ones: +; more zeros: -; 000111 and 0011: +; 111000 and 1100: -)
  function automatic bit rd6(input [5:0] v, input bit rd);
    return (n6(v) > 3) ? 1'b1 : (n6(v) < 3) ? 1'b0 : (v == 6'b000111) ? 1'b1 : (v == 6'b111000) ? 1'b0 : rd;
  endfunction
  function automatic bit rd4(input [3:0] v, input bit rd);
    return (n4(v) > 2) ? 1'b1 : (n4(v) < 2) ? 1'b0 : (v == 4'b0011) ? 1'b1 : (v == 4'b1100) ? 1'b0 : rd;
  endfunction
  // faults: [0] no_rd [1] a7_never [2] keep_rd_on_unbalanced [3] no_balanced_flip
  function automatic [10:0] core(input [7:0] d, input bit k, input bit rd_in, input [3:0] f);
    reg [5:0] six; reg [3:0] four; reg rd0, r6, rd1, a7, kk; reg [4:0] x; reg [2:0] y; int o6, o4;
    x = d[4:0]; y = d[7:5]; kk = k && k_ok(d); rd0 = f[0] ? 1'b0 : rd_in;
    six = (kk && x == 5'd28) ? 6'b001111 : t6(x); o6 = n6(six);
    if (rd0 && (o6 != 3 || (six == 6'b111000 && !f[3]))) begin six = ~six; o6 = 6 - o6; end
    r6 = (o6 > 3) ? 1'b1 : (o6 < 3) ? 1'b0 : (six == 6'b000111) ? 1'b1 : (six == 6'b111000) ? 1'b0 : rd0;
    rd1 = f[2] ? rd0 : r6;
    if (kk) begin
      four = t4k(y); if (rd1) four = ~four;
    end else begin
      a7 = (y == 3'd7) && !f[1] && ((!rd1 && (x == 5'd17 || x == 5'd18 || x == 5'd20)) || (rd1 && (x == 5'd11 || x == 5'd13 || x == 5'd14)));
      four = a7 ? 4'b0111 : t4d(y);
      if (rd1 && (n4(four) != 2 || (four == 4'b1100 && !f[3]))) four = ~four;
    end
    o4 = n4(four);
    return {(o4 > 2) ? 1'b1 : (o4 < 2) ? 1'b0 : (four == 4'b0011) ? 1'b1 : (four == 4'b1100) ? 1'b0 : r6, six, four};
  endfunction
  function automatic [10:0] encode(input [7:0] d, input bit k, input bit rd_in);
    if (k && !k_ok(d)) bad_k++;
    return core(d, k, rd_in, {no_balanced_flip, keep_rd_on_unbalanced, a7_never, no_rd});
  endfunction
  function automatic void build();
    reg [10:0] c;
    for (int i = 0; i < 1024; i++) begin valid_m[i] = 0; valid_p[i] = 0; kd[i] = 9'd0; end
    for (int i = 0; i < 268; i++) begin
      reg [7:0] d; reg k;
      if (i < 256) begin d = i[7:0]; k = 0; end
      else begin k = 1; d = (i < 264) ? {3'(i - 256), 5'd28} : (i == 264) ? 8'hf7 : (i == 265) ? 8'hfb : (i == 266) ? 8'hfd : 8'hfe; end
      c = core(d, k, 1'b0, 4'd0); valid_m[c[9:0]] = 1; kd[c[9:0]] = {k, d};
      c = core(d, k, 1'b1, 4'd0); valid_p[c[9:0]] = 1; kd[c[9:0]] = {k, d};
    end
    built = 1;
  endfunction
  function automatic [11:0] decode(input [9:0] code, input bit rd_in);
    reg here, there, ce, de, r;
    if (!built) build();
    here = rd_in ? valid_p[code] : valid_m[code];
    there = rd_in ? valid_m[code] : valid_p[code];
    ce = !(here || there); de = !ce && !here && !dec_no_disp_check;
    r = rd4(code[3:0], rd6(code[9:4], rd_in));
    return {r, de, ce, ce ? 9'd0 : kd[code]};
  endfunction
  function automatic [9:0] enc(input [7:0] d, input bit k);
    reg [10:0] r; r = encode(d, k, rd_tx); rd_tx = r[10];
    if (trace) $display("s%0d TX %s%0d.%0d code=%b rd=%s", symbols, (k && k_ok(d)) ? "K" : "D", d[4:0], d[7:5], r[9:0], r[10] ? "+" : "-");
    symbols++;
    return r[9:0];
  endfunction
  function automatic [8:0] dec(input [9:0] code);
    reg [11:0] r; r = decode(code, rd_rx); rd_rx = r[11];
    last_disp_err = r[10]; last_code_err = r[9]; last_k = r[8];
    if (r[9]) code_errs++; if (r[10]) disp_errs++;
    if (trace && (r[9] || r[10])) $display("RX %b %s", code, r[9] ? "code error" : "disparity error");
    return r[8:0];
  endfunction
  function automatic bit comma7(input [6:0] w); return w == 7'b0011111 || w == 7'b1100000; endfunction
endmodule

// ---------------------------------------------------------------------------------------------
// hs_crc: a CRC of 1 to 32 bits with any polynomial, seed, bit order and final inversion.
// The register shifts left; the polynomial omits the x^width term. The field is sent register bit
// width-1 first (USB 2.0, USB 3.2 and Ethernet all send it this way).
//   use_crc32(), use_crc16_usb2(), use_crc5_usb2(), use_crc16_usb3(): parameter sets
//   reset(), crc_bit(b), crc_byte(v), crc_bits(v, n), field(), field_bit(i), check_value(), crc_residue_ok()
// Faults: msb_first (bytes enter MSB first), no_invert (the field is not complemented), seed_zero.
module hs_crc;
  int width = 32;
  bit [31:0] poly = 32'h04c11db7, seed = 32'hffffffff, residue = 32'hc704dd7b;
  bit lsb_first = 1, invert = 1;
  bit msb_first = 0, no_invert = 0, seed_zero = 0;
  bit [31:0] r = 32'hffffffff;
  function automatic [31:0] mask(); return (width >= 32) ? 32'hffffffff : ((32'd1 << width) - 32'd1); endfunction
  function automatic void reset(); r = seed_zero ? 32'd0 : (seed & mask()); endfunction
  function automatic void set(input int w, input [31:0] p, input [31:0] s, input [31:0] res, input bit lsb, input bit inv);
    width = w; poly = p; seed = s; residue = res; lsb_first = lsb; invert = inv; reset();
  endfunction
  function automatic void use_crc32();      set(32, 32'h04c11db7, 32'hffffffff, 32'hc704dd7b, 1, 1); endfunction
  function automatic void use_crc16_usb2(); set(16, 32'h8005, 32'hffff, 32'h800d, 1, 1); endfunction
  function automatic void use_crc5_usb2();  set(5, 32'h05, 32'h1f, 32'h0c, 1, 1); endfunction
  function automatic void use_crc16_usb3(); set(16, 32'h100b, 32'hffff, 32'hf6aa, 1, 1); endfunction
  function automatic void crc_bit(input bit b);
    reg fb; fb = b ^ r[width - 1];
    r = ((r << 1) ^ (fb ? poly : 32'd0)) & mask();
  endfunction
  function automatic void crc_byte(input [7:0] v);
    for (int i = 0; i < 8; i++) crc_bit(v[(lsb_first ^ msb_first) ? i : 7 - i]);
  endfunction
  function automatic void crc_bits(input [31:0] v, input int n);   // n bits of v, bit 0 first
    for (int i = 0; i < n; i++) crc_bit(v[i]);
  endfunction
  function automatic [31:0] field(); return (invert && !no_invert) ? (~r & mask()) : r; endfunction
  function automatic bit field_bit(input int i); reg [31:0] f; f = field(); return f[width - 1 - i]; endfunction
  // the usual published "check" number: the field with its first-sent bit read as bit 0
  function automatic [31:0] check_value();
    reg [31:0] f, o; f = field(); o = 32'd0;
    for (int i = 0; i < width; i++) o[i] = f[width - 1 - i];
    return lsb_first ? o : f;
  endfunction
  function automatic bit crc_residue_ok(); return r == (residue & mask()); endfunction
endmodule

// ---------------------------------------------------------------------------------------------
// hs_scr: additive (frame-synchronous) and multiplicative (self-synchronising) scramblers.
// poly holds the coefficients: bit k is x^k; the +1 term is always used (taps() sets bit 0); len is the degree.
// Additive: a Galois LFSR. The key bit is s[len-1]; each step shifts left and adds the low terms of
//   the polynomial when the key bit is 1. The data never enters the register.
// Multiplicative: the line bit is the data bit XOR the register bits at the polynomial's terms;
//   the scrambler shifts its own output in, the descrambler shifts the received line bit in.
//   scr_add(len, poly, seed), scr_mul(len, poly), use_usb3_gen1(), use_x58(), use_x23_usb3() (see its note)
//   scr_bit(b), dscr_bit(b), scr_byte(v), dscr_byte(v) (bit 0 first), scr_reset(), scr_hold() (a skip
//   symbol: no step), scr_unscrambled() (a symbol sent in the clear: 8 steps, data untouched)
// Faults: advance_on_skip (scr_hold steps the LFSR 8 times), no_reset (scr_reset does nothing),
//         wrong_tap (the lowest term x^k becomes x^(k+1)), seed_zero (scr_reset loads 0).
module hs_scr;
  bit mult = 0; int len = 16;
  bit [63:0] poly = 64'h10039, seed = 64'hffff;
  bit advance_on_skip = 0, no_reset = 0, wrong_tap = 0, seed_zero = 0;
  bit [63:0] s = 64'hffff;
  int steps = 0;
  function automatic [63:0] lmask(); return (len >= 64) ? 64'hffffffffffffffff : ((64'd1 << len) - 64'd1); endfunction
  function automatic [63:0] taps();
    reg [63:0] p; int k; p = poly | 64'd1; k = 1;
    if (wrong_tap) begin
      while (k < len && !p[k]) k++;
      if (k < len) begin p[k] = 1'b0; p[k + 1] = 1'b1; end
    end
    return p;
  endfunction
  function automatic void load(); s = (seed_zero ? 64'd0 : seed) & lmask(); endfunction
  function automatic void scr_add(input int n, input [63:0] p, input [63:0] sd); mult = 0; len = n; poly = p; seed = sd; s = sd & lmask(); endfunction
  function automatic void scr_mul(input int n, input [63:0] p); mult = 1; len = n; poly = p; seed = 64'd0; s = 64'd0; endfunction
  function automatic void use_usb3_gen1(); scr_add(16, 64'h10039, 64'hffff); endfunction   // x^16 + x^5 + x^4 + x^3 + 1, seed FFFFh
  function automatic void use_x58(); scr_mul(58, (64'd1 << 58) | (64'd1 << 39) | 64'd1); endfunction   // x^58 + x^39 + 1
  // USB 3.2 Gen 2 (§6.3.2.3) polynomial x^23 + x^21 + x^16 + x^8 + x^5 + x^2 + 1 with seed 1DBFBCh. Only the
  // polynomial and seed are the specification's: the register form here is this library's Galois form, and
  // the reset and bypass rules of §6.3.2.3 are not modelled, so do not quote its key stream as USB's.
  function automatic void use_x23_usb3(); scr_add(23, (64'd1 << 23) | (64'd1 << 21) | (64'd1 << 16) | (64'd1 << 8) | (64'd1 << 5) | (64'd1 << 2) | 64'd1, 64'h1dbfbc); endfunction
  function automatic void scr_reset(); if (!no_reset) load(); endfunction
  function automatic bit key(); return s[len - 1]; endfunction
  function automatic void step();
    reg kb; kb = s[len - 1];
    s = ((s << 1) & lmask()) ^ (kb ? (taps() & lmask()) : 64'd0);
    steps++;
  endfunction
  // the XOR of the register bits at the polynomial's terms x^1..x^len (bit k-1 of the register for x^k)
  function automatic bit fbx(input [63:0] st); return ^(st & (taps() >> 1) & lmask()); endfunction
  function automatic bit scr_bit(input bit b);
    reg o;
    if (!mult) begin o = b ^ s[len - 1]; step(); end
    else begin o = b ^ fbx(s); s = ((s << 1) | {63'd0, o}) & lmask(); steps++; end
    return o;
  endfunction
  function automatic bit dscr_bit(input bit b);
    reg o;
    if (!mult) begin o = b ^ s[len - 1]; step(); end
    else begin o = b ^ fbx(s); s = ((s << 1) | {63'd0, b}) & lmask(); steps++; end
    return o;
  endfunction
  function automatic [7:0] scr_byte(input [7:0] v);
    reg [7:0] o; for (int i = 0; i < 8; i++) o[i] = scr_bit(v[i]); return o;
  endfunction
  function automatic [7:0] dscr_byte(input [7:0] v);
    reg [7:0] o; for (int i = 0; i < 8; i++) o[i] = dscr_bit(v[i]); return o;
  endfunction
  // a skip symbol passes unscrambled and the LFSR holds
  function automatic void scr_hold(); if (advance_on_skip && !mult) for (int i = 0; i < 8; i++) step(); endfunction
  // another symbol that is sent unscrambled (a K code other than COM and SKP): the LFSR still steps 8 times
  function automatic void scr_unscrambled(); if (!mult) for (int i = 0; i < 8; i++) step(); endfunction
endmodule
Read included file: eth_mac.sv
`timescale 1ns/1ns
// eth_frame: one MAC frame as octets, its packet as wire bits, and a bit-serial receiver.
//   pay[i]                         client data, set by the bench before build()
//   build(da, sa, lt, len)         destination, source, Length/Type, len data octets, then the FCS -> oct[0..n-1].
//                                  It adds no pad: give it 46 data octets or more. (Padding is P11.2.1's task; the
//                                  pages show the padding MAC's frames as measured tables.)
//   wire_bits(), wire_bit(i)       the packet in transmit order: preamble, SFD, frame
//   rx_start(), rx_bit(b), rx_end()  hunt for the SFD, collect octets, then parse()
//   parse()                        da, sa, lt, is_length, is_type, data_len, fcs_rx, fcs_calc, fcs_ok
// Faults: fcs_msb_first, fcs_no_invert, fcs_covers_preamble, sfd_wrong, msb_first_octets.
module eth_frame;
  localparam int MIN_FRAME = 64, MAX_BASIC = 1518, MAX_QTAG = 1522, MAX_ENVELOPE = 2000;
  bit fcs_msb_first = 0, fcs_no_invert = 0, fcs_covers_preamble = 0, sfd_wrong = 0, msb_first_octets = 0;
  hs_crc crc();
  bit [7:0] pay [0:2047];
  bit [7:0] oct [0:2047];
  int n = 0;
  bit [47:0] da = 0, sa = 0; bit [15:0] lt = 0;
  bit is_length = 0, is_type = 0, fcs_ok = 0;
  int data_len = 0;
  bit [31:0] fcs_rx = 0, fcs_calc = 0;
  // receiver state
  bit in_frame = 0; bit [7:0] hist = 0, cur = 0; int nb = 0, excess = 0, sfd_at = -1, bits_seen = 0;

  // The FCS of oct[0..len-1] as four octets: the first octet sent is in [7:0].
  function automatic [31:0] fcs_of(input int len);
    crc.use_crc32(); crc.msb_first = fcs_msb_first; crc.no_invert = fcs_no_invert; crc.reset();
    if (fcs_covers_preamble) begin
      for (int i = 0; i < 7; i++) crc.crc_byte(8'h55);
      crc.crc_byte(8'hd5);
    end
    for (int i = 0; i < len; i++) crc.crc_byte(oct[i]);
    return crc.check_value();
  endfunction

  function automatic void build(input [47:0] d, input [47:0] s, input [15:0] t, input int len);
    int k; reg [31:0] f;
    k = 0;
    for (int i = 0; i < 6; i++) begin oct[k] = d[47 - 8*i -: 8]; k++; end
    for (int i = 0; i < 6; i++) begin oct[k] = s[47 - 8*i -: 8]; k++; end
    oct[k] = t[15:8]; k++;
    oct[k] = t[7:0]; k++;
    for (int i = 0; i < len; i++) begin oct[k] = pay[i]; k++; end
    f = fcs_of(k);
    for (int i = 0; i < 4; i++) begin oct[k] = f[8*i +: 8]; k++; end
    n = k; excess = 0;
    parse();
  endfunction

  function automatic void parse();
    da = 0; sa = 0; lt = 0; is_length = 0; is_type = 0; fcs_ok = 0; data_len = 0; fcs_rx = 0; fcs_calc = 0;
    if (n >= 14) begin
      da = {oct[0], oct[1], oct[2], oct[3], oct[4], oct[5]};
      sa = {oct[6], oct[7], oct[8], oct[9], oct[10], oct[11]};
      lt = {oct[12], oct[13]};
      is_length = (lt <= 16'd1500);
      is_type = (lt >= 16'd1536);
    end
    if (n >= 18) begin
      fcs_rx = {oct[n-1], oct[n-2], oct[n-3], oct[n-4]};
      fcs_calc = fcs_of(n - 4);
      fcs_ok = (fcs_rx == fcs_calc);
      data_len = is_length ? int'(lt) : n - 18;
    end
  endfunction

  function automatic int wire_bits(); return 8 * (8 + n); endfunction
  function automatic bit wire_bit(input int i);
    int o, b; reg [7:0] v;
    o = i / 8; b = i % 8;
    if (o < 7) v = 8'h55;
    else if (o == 7) v = sfd_wrong ? 8'h55 : 8'hd5;
    else v = oct[o - 8];
    return msb_first_octets ? v[7 - b] : v[b];
  endfunction

  function automatic void rx_start();
    in_frame = 0; hist = 0; cur = 0; nb = 0; n = 0; excess = 0; sfd_at = -1; bits_seen = 0;
  endfunction
  function automatic void rx_bit(input bit b);
    bits_seen++;
    if (!in_frame) begin
      hist = {hist[6:0], b};                      // the oldest bit is hist[7]
      if (hist == 8'b10101011) begin in_frame = 1; sfd_at = bits_seen; end
    end else begin
      if (msb_first_octets) cur[7 - nb] = b; else cur[nb] = b;
      nb++;
      if (nb == 8) begin oct[n] = cur; n++; nb = 0; end
    end
  endfunction
  function automatic void rx_end(); excess = nb; parse(); endfunction
endmodule
// eth_axis: a MAC client bus in the style of AXI4-Stream (IHI 0051B 2.2 handshake, 2.5 TKEEP, 2.6 TLAST, 2.9 TUSER),
// 64 bits wide. Byte 0 of a beat is tdata[7:0] and is first in the frame (AXI4-Stream 2.4.1). Bench conventions,
// not AXI4-Stream's or 802.3's: tkeep is all ones except on the last beat, where it covers bytes 0 to k-1; one tuser
// bit (transfer-based, 2.9.1), read on the last beat only, marks a bad frame (receive) or asks the MAC to abort it
// (transmit).
//   load(n)                  beats for octets oct[0..n-1]: bd[], bk[], bl[], nbeats; bv[] = valid per cycle, ncyc
//   tx_cycles()              the transmit MAC: one beat per cycle once a frame has started. Returns 0 sent,
//                            1 underrun (tvalid fell inside the frame), 2 aborted by tuser. sent_octets, fail_cycle.
// Fault: tvalid_gap (load() leaves cycle 3 of the frame empty: the client was late with a beat).
module eth_axis;
  bit tvalid_gap = 0;
  bit [7:0] oct [0:2047];
  bit [63:0] bd [0:300]; bit [7:0] bk [0:300]; bit bl [0:300]; bit bu [0:300];
  int nbeats = 0;
  bit bv [0:301]; int bix [0:301]; int ncyc = 0;
  int sent_octets = 0, fail_cycle = -1;
  function automatic void load(input int n);
    int b, k;
    nbeats = (n + 7) / 8;
    for (b = 0; b < nbeats; b++) begin
      bd[b] = 64'd0; bk[b] = 8'd0; bl[b] = (b == nbeats - 1); bu[b] = 0;
      for (k = 0; k < 8; k++) if (8*b + k < n) begin bd[b][8*k +: 8] = oct[8*b + k]; bk[b][k] = 1'b1; end
    end
    ncyc = 0;
    for (b = 0; b < nbeats; b++) begin
      if (tvalid_gap && b == 3) begin bv[ncyc] = 0; bix[ncyc] = -1; ncyc++; end
      bv[ncyc] = 1; bix[ncyc] = b; ncyc++;
    end
  endfunction
  function automatic int tx_cycles();
    bit started; started = 0; sent_octets = 0; fail_cycle = -1;
    for (int c = 0; c < ncyc; c++) begin
      if (!bv[c]) begin
        if (started) begin fail_cycle = c; return 1; end
      end else begin
        started = 1;
        if (bl[bix[c]] && bu[bix[c]]) begin fail_cycle = c; return 2; end
        for (int k = 0; k < 8; k++) if (bk[bix[c]][k]) sent_octets++;
      end
    end
    return 0;
  endfunction
endmodule

// eth_pause: the PAUSE function of MAC Control (Annex 31B) at the station that receives PAUSE frames, in octet
// times (one octet time is 8 bit times; a pause quantum is 512 bit times = 64 octet times, 31B.2).
//   reset(), rx_pause(t, q)  a valid PAUSE frame with pause_time q ended at time t: the timer restarts (31B.3.3)
//   may_start(t)             1 when a new data frame may start at time t. A frame already started is never cut
//                            (31B.3.7). react is the bench's reaction time: frames may still start until t + react.
//   paused_until             the time the timer runs out
//   pause_octets(q, o[])     not here: build a PAUSE frame with eth_frame (DA 01-80-C2-00-00-01, 8808h, 0001h, q)
// Faults: pause_ignored, pause_adds_not_overrides (a new frame adds to the timer, and zero does not cancel),
//         slow_reaction (react = 70 quanta, over the 60 allowed at 10 Gb/s), timer_in_bits (q counts bit times).
module eth_pause;
  localparam int QUANTUM = 64;                     // octet times
  bit pause_ignored = 0, pause_adds_not_overrides = 0, slow_reaction = 0, timer_in_bits = 0;
  int react = 0, t_rx = -1, paused_until = 0;
  function automatic void reset(); t_rx = -1; paused_until = 0; endfunction
  function automatic void rx_pause(input int t, input int q);
    int len;
    if (pause_ignored) return;
    len = timer_in_bits ? (q + 7) / 8 : q * QUANTUM;
    if (pause_adds_not_overrides && paused_until > t) paused_until = paused_until + len;
    else paused_until = t + len;
    t_rx = t;
  endfunction
  function automatic bit may_start(input int t);
    int r;
    r = slow_reaction ? 70 * QUANTUM : react;
    if (t_rx < 0) return 1;
    if (t < t_rx + r) return 1;
    return t >= paused_until;
  endfunction
endmodule

// eth_pfc: priority-based flow control (Annex 31D). The frame is 802.3's; holding a priority's queue is the MAC
// Control client's job (IEEE 802.1Q, not held), so the eight timers here are a bench client, in octet times.
//   build(f_oct[], pev, times[])   not here: the bench writes opcode 01-01, the vector and eight times into eth_frame
//   reset(), rx(t, pev, tm[0..7])  for each e[n] = 1 (bit n of the vector's low octet), priority n stops until
//                                  t + 64 * time[n] (hold_end[n]); e[n] = 0 leaves priority n alone; time[n] = 0 releases it
//   blocked(n, t)                  1 while priority n is held
// Fault: pfc_wrong_priority (reads e[n] from bit 7 - n).
module eth_pfc;
  bit pfc_wrong_priority = 0;
  int hold_end [0:7];
  function automatic void reset(); for (int i = 0; i < 8; i++) hold_end[i] = 0; endfunction
  function automatic void rx(input int t, input [15:0] pev, input [127:0] tm);   // tm[16*n +: 16] = time[n]
    bit e;
    for (int n = 0; n < 8; n++) begin
      e = pfc_wrong_priority ? pev[7 - n] : pev[n];
      if (e) hold_end[n] = t + 64 * int'(tm[16*n +: 16]);
    end
  endfunction
  function automatic bit blocked(input int n, input int t); return t < hold_end[n]; endfunction
endmodule

// eth_csma_tx: one half-duplex transmitter (4.2.3.2), one call of tick() per octet time.
//   reset(), load(frame_octets)   a frame of frame_octets (DA to FCS) waits to be sent; it is padded to min_frame
//   tick(carrier)                 carrier: another station's signal is on the wire here now. Returns 1 when the
//                                 station puts an octet (packet or jam) on the wire.
//   plan[i]                       the wait, in slots, after collision i + 1. The bench sets it (default 0). This
//                                 readable station draws nothing and has no attempt limit.
//   state  0 idle, 1 defer, 2 send, 3 jam, 4 backoff, 5 sent (as far as the sender knows)
//   pkt, sent, quiet, left, attempts, late, last_start, last_r
// min_frame is 64 octets; a bench may lower it to show why it is 64. Fault: no_backoff (every wait is 0 slots).
// Deference is a bench simplification: the 12-octet quiet count restarts on any carrier, own or received, and the
// station never starts while carrier is present. 4.2.8 restarts only the first part of the gap, and then transmits
// whatever the carrier.
module eth_csma_tx;
  localparam int SLOT = 64, JAM = 4, GAP = 12, PRE = 8;   // octet times
  bit no_backoff = 0;
  int min_frame = 64;
  int plan [0:63];
  int state = 0, pkt = 0, sent = 0, quiet = GAP, left = 0, attempts = 0, late = 0, last_start = -1, last_r = 0, now = 0;
  function automatic void reset();
    state = 0; pkt = 0; sent = 0; quiet = GAP; left = 0; attempts = 0; late = 0; last_start = -1; last_r = 0; now = 0;
  endfunction
  function automatic void load(input int frame_octets);
    pkt = PRE + frame_octets;
    if (frame_octets < min_frame) pkt = PRE + min_frame;
    state = 1; attempts = 0; sent = 0; late = 0;
  endfunction
  function automatic bit tick(input bit carrier);
    bit on;
    on = 0;
    if (state == 1 && !carrier && quiet >= GAP) begin state = 2; sent = 0; last_start = now; end
    if (state == 2 && carrier) begin
      attempts++; if (sent > SLOT) late++;
      state = 3; left = JAM;
    end
    case (state)
      2: begin sent++; on = 1; if (sent == pkt) state = 5; end
      3: begin
           on = 1; left--;
           if (left == 0) begin
             last_r = no_backoff ? 0 : plan[(attempts - 1) % 64];
             left = SLOT * last_r;
             state = (left == 0) ? 1 : 4;
           end
         end
      4: begin left--; if (left == 0) state = 1; end
      default: ;
    endcase
    quiet = (carrier || on) ? 0 : ((quiet < GAP) ? quiet + 1 : GAP);
    now++;
    return on;
  endfunction
endmodule

// eth_csma: two eth_csma_tx stations, A and B, at the two ends of a wire with a one-way delay of d octet times.
//   run(fa, ready_a, fb, ready_b, tmax)   each station loads its frame (fa, fb octets) at its ready time
//   on_a[t], on_b[t]          what each station put on the wire at time t
//   ev_t[], ev_who[] (0 A, 1 B), ev_kind[], ev_v[], n_ev   the event log:
//     kind 0 starts attempt v; 1 sees a collision after v octets; 2 jam over, backs off v slots;
//     3 last octet sent (v = octets); 4 gives up after v attempts
//   delivered(i)              1 when station i's last attempt reached the far end with no overlap there
//   a.plan[], b.plan[], a.no_backoff, b.no_backoff, a.min_frame, b.min_frame: the stations' settings
module eth_csma;
  eth_csma_tx a(); eth_csma_tx b();
  int d = 10, n_ev = 0, tend = 0;
  bit on_a [0:16383]; bit on_b [0:16383];
  int ev_t [0:255]; int ev_who [0:255]; int ev_kind [0:255]; int ev_v [0:255];
  function automatic void log_ev(input int t, input int who, input int kind, input int v);
    if (n_ev < 256) begin ev_t[n_ev] = t; ev_who[n_ev] = who; ev_kind[n_ev] = kind; ev_v[n_ev] = v; n_ev++; end
  endfunction
  function automatic void note(input int t, input int who, input int s0, input int s1, input int sent0, input int att, input int r, input int sent1);
    if (s0 != 2 && s1 == 2) log_ev(t, who, 0, att + 1);
    if (s0 == 2 && (s1 == 3 || s1 == 4)) log_ev(t, who, 1, sent0);
    if (s0 == 3 && (s1 == 4 || s1 == 1)) log_ev(t, who, 2, r);
    if (s0 != 5 && s1 == 5) log_ev(t, who, 3, sent1);
    if (s0 != 6 && s1 == 6) log_ev(t, who, 4, att);
  endfunction
  function automatic void run(input int fa, input int ready_a, input int fb, input int ready_b, input int tmax);
    bit ca, cb; int sa, sb, xa, xb;
    a.reset(); b.reset(); n_ev = 0; tend = tmax;
    for (int t = 0; t < tmax; t++) begin
      if (t == ready_a) a.load(fa);
      if (t == ready_b) b.load(fb);
      ca = (t >= d) ? on_b[t - d] : 1'b0;
      cb = (t >= d) ? on_a[t - d] : 1'b0;
      sa = a.state; sb = b.state; xa = a.sent; xb = b.sent;
      on_a[t] = a.tick(ca);
      on_b[t] = b.tick(cb);
      note(t, 0, sa, a.state, xa, a.attempts, a.last_r, a.sent);
      note(t, 1, sb, b.state, xb, b.attempts, b.last_r, b.sent);
    end
  endfunction
  function automatic bit delivered(input int i);
    int s, p, u;
    if (i == 0 && a.state != 5) return 0;
    if (i == 1 && b.state != 5) return 0;
    s = (i == 0) ? a.last_start : b.last_start;
    p = (i == 0) ? a.pkt : b.pkt;
    for (int t = s; t < s + p; t++) begin
      u = t + d;
      if (u < tend && ((i == 0) ? on_b[u] : on_a[u])) return 0;
    end
    return 1;
  endfunction
endmodule

// eth_gap: how long the gap before the next Start is on a 4-lane XGMII, where Start must sit on lane 0
// (46.3.1.4). A gap counts every character from the Terminate to the last idle before Start. A packet is
// 8 + n characters (Start, six preamble octets, SFD, an n-octet frame) and starts on lane 0.
//   reset()                     DIC = 0 (the count is reset only at initialisation)
//   method                      0 deficit idle count, 1 always insert (both allowed by 46.3.1.4)
//   next_gap(n, mac_gap)        the gap after an n-octet frame when the MAC asks for mac_gap (12 or more)
//   deleted, inserted, dic      what the last call did, and the count after it
// Faults: ipg_min_only (always deletes, ignoring the bound), dic_max4 (bounds the count at 4, not 3),
//         start_any_lane (no alignment: the gap is always mac_gap).
module eth_gap;
  bit ipg_min_only = 0, dic_max4 = 0, start_any_lane = 0;
  int method = 0, dic = 0, deleted = 0, inserted = 0;
  function automatic void reset(); dic = 0; deleted = 0; inserted = 0; endfunction
  function automatic int next_gap(input int n, input int mac_gap);
    int m, top;
    deleted = 0; inserted = 0;
    m = (n + mac_gap) % 4;                       // lanes past lane 0 the next Start would land on
    if (start_any_lane || m == 0) return mac_gap;
    top = dic_max4 ? 4 : 3;
    if (method == 0 && (ipg_min_only || dic + m <= top)) begin deleted = m; dic = dic + m; end
    else begin inserted = 4 - m; if (method == 0) dic = dic - (4 - m); end
    return mac_gap - deleted + inserted;
  endfunction
endmodule
Read included file: eth_pcs.sv
`timescale 1ns/1ns
// eth_pcs.sv: the 1000BASE-X PCS, transmit side and synchronization (read-only). It sits on hs_8b10b (hs_code.sv).

// eth_1000x: the transmit ordered-set layer (36.2.4). The stream is kept as {k, d} and as ten coded bits.
//   clear()            empty stream, running disparity negative
//   idle(k)            k idle ordered sets. Each tests the running disparity first (Figure 36-6):
//                      positive -> /I1/ (K28.5 D5.6), negative -> /I2/ (K28.5 D16.2)
//   cfg(word, k)       k configuration ordered sets, /C1/ and /C2/ in turn: K28.5, D21.5 or D2.2, word[7:0], word[15:8]
//   start_packet()     /S/ in place of the first preamble octet, then six 55h and D5h
//   data(d)            one data code-group
//   end_packet()       /T/ /R/, and one more /R/ when the first /R/ went out on an even position
//   err()              /V/
//   put(k, d)          any code-group
//   n                  code-groups so far; code-group i is even-numbered when i is even
//   sym[i] = {k, d};  code[i] = abcdei fghj, bit a (code[i][9]) is sent first;  rdb[i] = running disparity before i
//   is_k(i, d), comma_plus(), comma_minus()
// Fault: idle_wrong_disparity (every idle is /I2/, so a positive running disparity is never corrected).
module eth_1000x;
  bit idle_wrong_disparity = 0;
  hs_8b10b c8();
  bit [8:0] sym [0:8191]; bit [9:0] code [0:8191]; bit rdb [0:8191];
  int n = 0; bit c2 = 0;
  function automatic void clear(); n = 0; c2 = 0; c8.rd_tx = 0; endfunction
  function automatic void put(input bit k, input [7:0] d);
    sym[n] = {k, d}; rdb[n] = c8.rd_tx; code[n] = c8.enc(d, k); n++;
  endfunction
  function automatic void idle(input int k);
    bit positive;
    for (int i = 0; i < k; i++) begin
      positive = c8.rd_tx && !idle_wrong_disparity;
      put(1'b1, 8'hbc);                                // K28.5
      put(1'b0, positive ? 8'hc5 : 8'h50);             // D5.6 or D16.2
    end
  endfunction
  function automatic void cfg(input [15:0] word, input int k);
    for (int i = 0; i < k; i++) begin
      put(1'b1, 8'hbc);
      put(1'b0, c2 ? 8'h42 : 8'hb5);                   // D2.2 or D21.5
      put(1'b0, word[7:0]); put(1'b0, word[15:8]);
      c2 = !c2;
    end
  endfunction
  function automatic void data(input [7:0] d); put(1'b0, d); endfunction
  function automatic void start_packet();
    put(1'b1, 8'hfb);                                  // /S/ = K27.7
    for (int i = 0; i < 6; i++) put(1'b0, 8'h55);
    put(1'b0, 8'hd5);
  endfunction
  function automatic void end_packet();
    put(1'b1, 8'hfd);                                  // /T/ = K29.7
    put(1'b1, 8'hf7);                                  // /R/ = K23.7
    if (n % 2 != 0) put(1'b1, 8'hf7);                  // that /R/ was even-numbered: one more
  endfunction
  function automatic void err(); put(1'b1, 8'hfe); endfunction     // /V/ = K30.7
  function automatic bit is_k(input int i, input [7:0] d); return sym[i] == {1'b1, d}; endfunction
  function automatic int comma_plus();
    int c; c = 0;
    for (int i = 0; i < n; i++) if (code[i][9:3] == 7'b0011111) c++;
    return c;
  endfunction
  function automatic int comma_minus();
    int c; c = 0;
    for (int i = 0; i < n; i++) if (code[i][9:3] == 7'b1100000) c++;
    return c;
  endfunction
endmodule

// eth_1000x_sync: the synchronization process of Figure 36-9, one call of rx() per ten-bit code-group.
//   reset()            LOSS_OF_SYNC
//   rx(code)           takes one code-group; returns sync_status (1 = OK)
//   state              0 LOSS_OF_SYNC, 1 COMMA_DETECT_1, 2 ACQUIRE_SYNC_1, 3 COMMA_DETECT_2, 4 ACQUIRE_SYNC_2,
//                      5 COMMA_DETECT_3, 6 SYNC_ACQUIRED_1, 7 SYNC_ACQUIRED_2, 8 SYNC_ACQUIRED_2A,
//                      9 SYNC_ACQUIRED_3, 10 SYNC_ACQUIRED_3A, 11 SYNC_ACQUIRED_4, 12 SYNC_ACQUIRED_4A
//   even               the code-group just taken was even-numbered
//   good_cgs, bad_seen (every bad code-group since reset), k, d (the last decode)
// A code-group is bad when it is invalid, or when it holds a comma and is odd-numbered (36.2.5.1.3).
// Bench choices: in LOSS_OF_SYNC the decoder takes its running disparity from the comma it finds; an invalid
// code-group leaves the decoder's running disparity as the received bits set it.
module eth_1000x_sync;
  hs_8b10b c8();
  int state = 0, good_cgs = 0, bad_seen = 0;
  bit even = 0, sync = 0, rd = 0, k = 0; bit [7:0] d = 0;
  function automatic void reset(); state = 0; good_cgs = 0; bad_seen = 0; even = 0; sync = 0; rd = 0; endfunction
  function automatic bit rx(input [9:0] code);
    reg [11:0] r; bit invalid, comma, is_d, bad;
    comma = code[9:3] == 7'b0011111 || code[9:3] == 7'b1100000;
    if (state == 0 && comma) rd = (code[9:3] == 7'b1100000);
    r = c8.decode(code, rd);                           // {rd_out, disp_err, code_err, k, d}
    rd = r[11]; k = r[8]; d = r[7:0];
    invalid = r[10] || r[9];
    is_d = !invalid && !r[8];
    bad = invalid || (comma && even);                  // even: the one before was even, so this one is odd
    if (bad && state != 0) bad_seen++;
    case (state)
      0: begin if (comma) begin state = 1; even = 1; end else even = !even; end
      1, 3, 5: begin even = 0; state = is_d ? state + 1 : 0; end
      2, 4: begin
        if (bad) state = 0;
        else if (comma) begin state = state + 1; even = 1; end
        else even = !even;
      end
      6: begin even = !even; if (bad) begin state = 7; good_cgs = 0; end end
      7, 9, 11: begin
        even = !even;
        if (bad) begin state = (state == 11) ? 0 : state + 2; good_cgs = 0; end
        else begin state = state + 1; good_cgs = 1; end
      end
      default: begin                                   // 8, 10, 12: counting good code-groups
        even = !even;
        if (bad) begin state = (state == 12) ? 0 : state + 1; good_cgs = 0; end
        else if (good_cgs == 3) begin state = (state == 8) ? 6 : state - 3; good_cgs = 0; end
        else good_cgs++;
      end
    endcase
    sync = state >= 6;
    return sync;
  endfunction
endmodule

// ---- 10GBASE-R and 25GBASE-R: 64B/66B blocks (Clause 49; Clause 107 uses the same code) ----
// Eight XGMII characters are one vector raw[71:0] (49.2.13.2.2): raw[k] is the control flag of character k,
// raw[8 + 8*k +: 8] its octet. A block is blk[65:0]; bit 0 is sent first. blk[1:0] is the sync header,
// blk[9:2] the block type field of a control block, the rest the payload (Figure 49-7).

// eth_66: the control blocks that hold no Start, no Terminate and no frame data.
//   c_code(x)       Table 49-1: the 7-bit C code of XGMII control code x; 7Fh if x is not in the table
//   enc_ctrl(raw)   {ok, blk}: block type 1Eh (eight control characters), 2Dh (four, then an ordered set),
//                   4Bh (an ordered set, then four) or 55h (two ordered sets); ok = 0 if raw is none of these.
//                   It only lays out the fields. Whether the vector may be sent is the transmit process's
//                   decision (eth_66_tx).
//   on_wire(blk)    the 66 bits as text in the order they are sent: sync, block type, payload
//   ham(a, b)       how many bits differ between two block type values
// Fault: wrong_block_type (types 2Dh and 4Bh are swapped).
module eth_66;
  bit wrong_block_type = 0;
  function automatic [6:0] c_code(input [7:0] x);
    case (x)
      8'h07: return 7'h00;                             // idle
      8'h06: return 7'h06;                             // low power idle
      8'hfe: return 7'h1e;                             // error
      8'h1c: return 7'h2d;                             // the six reserved characters
      8'h3c: return 7'h33;
      8'h7c: return 7'h4b;
      8'hbc: return 7'h55;
      8'hdc: return 7'h66;
      8'hf7: return 7'h78;
      default: return 7'h7f;
    endcase
  endfunction
  function automatic [7:0] ch(input [71:0] raw, input int k); return raw[8 + 8*k +: 8]; endfunction
  // characters k to k+3 are a sequence ordered set: 9Ch with its flag, then three data octets
  function automatic bit is_q(input [71:0] raw, input int k);
    return raw[k] && ch(raw, k) == 8'h9c && !raw[k + 1] && !raw[k + 2] && !raw[k + 3];
  endfunction
  // characters k to k+3 are control characters with a C code
  function automatic bit is_c4(input [71:0] raw, input int k);
    for (int j = k; j < k + 4; j++) if (!raw[j] || c_code(ch(raw, j)) == 7'h7f) return 0;
    return 1;
  endfunction
  function automatic [66:0] enc_ctrl(input [71:0] raw);
    reg [65:0] b; bit q0, q4, c0, c4;
    b = 66'd0;
    b[1:0] = 2'b01;                                    // sync header "10": bit 0, sent first, is 1
    q0 = is_q(raw, 0); q4 = is_q(raw, 4); c0 = is_c4(raw, 0); c4 = is_c4(raw, 4);
    if (c0 && c4) b[9:2] = 8'h1e;
    else if (c0 && q4) b[9:2] = wrong_block_type ? 8'h4b : 8'h2d;
    else if (q0 && c4) b[9:2] = wrong_block_type ? 8'h2d : 8'h4b;
    else if (q0 && q4) b[9:2] = 8'h55;
    else return 67'd0;
    if (c0) for (int k = 0; k < 4; k++) b[10 + 7*k +: 7] = c_code(ch(raw, k));
    else begin b[33:10] = raw[39:16]; b[37:34] = 4'h0; end     // D1 to D3, then the O code of the sequence set
    if (c4) for (int k = 4; k < 8; k++) b[10 + 7*k +: 7] = c_code(ch(raw, k));
    else begin b[41:38] = 4'h0; b[65:42] = raw[71:48]; end     // the O code, then D5 to D7
    return {1'b1, b};
  endfunction
  function automatic string on_wire(input [65:0] blk);
    string s;
    s = "";
    for (int i = 0; i < 66; i++) begin
      if (i == 2 || i == 10) s = {s, " "};
      s = {s, blk[i] ? "1" : "0"};
    end
    return s;
  endfunction
  function automatic int ham(input [7:0] a, input [7:0] b);
    int n; reg [7:0] x;
    x = a ^ b; n = 0;
    for (int i = 0; i < 8; i++) if (x[i]) n++;
    return n;
  endfunction
endmodule

// eth_66_tx: the transmit state diagram (Figure 49-16) without the EEE state. One call per vector.
//   step(t)   t is the T_TYPE of the vector: 0 C (control), 1 S (start), 2 T (terminate), 3 D (data), 4 E (none of these).
//             Returns 1 if the vector is encoded and sent, 0 if the error block goes out in its place.
//   state     0 TX_INIT, 1 TX_C, 2 TX_D, 3 TX_T, 4 TX_E
module eth_66_tx;
  int state = 0;
  function automatic void reset(); state = 0; endfunction
  function automatic bit step(input int t);
    case (state)
      0, 1, 3: state = (t == 0) ? 1 : (t == 1) ? 2 : 4;                    // TX_INIT, TX_C, TX_T: only C or S may follow
      2: state = (t == 3) ? 2 : (t == 2) ? 3 : 4;                          // TX_D: only D or T may follow
      default: state = (t == 2) ? 3 : (t == 3) ? 2 : (t == 0) ? 1 : 4;     // TX_E: T, D or C leave it
    endcase
    return state != 4;
  endfunction
endmodule

// eth_66_comp: clock compensation on XGMII columns (49.2.4.7, 49.2.4.10). Call once per column, in order.
// A column is {c[3:0], d[31:0]}: lane k is flag c[k] and octet d[8k+7:8k].
//   can_delete(c, d)   1 if this column may be dropped: four idles that hold none of the first four characters
//                      after a Terminate, or the second of two consecutive sequence ordered sets
//   can_insert(c, d)   1 if an idle column may be added after this one: it is idle or an ordered set
module eth_66_comp;
  bit guard = 0, prev_seq = 0;
  function automatic void reset(); guard = 0; prev_seq = 0; endfunction
  function automatic bit is_seq(input [3:0] c, input [31:0] d); return c == 4'b0001 && d[7:0] == 8'h9c; endfunction
  function automatic bit is_idle(input [3:0] c, input [31:0] d); return c == 4'b1111 && d == 32'h07070707; endfunction
  function automatic bit can_delete(input [3:0] c, input [31:0] d);
    bit ok, has_t;
    has_t = 0;
    for (int k = 0; k < 4; k++) if (c[k] && d[8*k +: 8] == 8'hfd) has_t = 1;
    ok = (is_idle(c, d) && !guard) || (is_seq(c, d) && prev_seq);
    guard = has_t;                                     // the next column holds some of the four characters after /T/
    prev_seq = is_seq(c, d) && !ok;                    // only one of the two
    return ok;
  endfunction
  function automatic bit can_insert(input [3:0] c, input [31:0] d); return is_idle(c, d) || is_seq(c, d); endfunction
endmodule

// eth_66_scr: the scrambler and the descrambler of 10GBASE-R (49.2.6, 49.2.10; Figures 49-8 and 49-10).
// The register is s[57:0]: stage S0 is s[0] and holds the newest line bit. Use one instance to scramble and
// another to descramble.
//   scr_bit(b)       one payload bit in, one line bit out: b XOR S38 XOR S57. The line bit shifts into S0.
//   dscr_bit(b)      one line bit in, one payload bit out: the same XOR. The received bit shifts into S0.
//   scramble(blk)    a whole block: bits 1:0 (the sync header) pass, bits 2 to 65 are scrambled in that order
//   descramble(blk)  the reverse
//   load(v)          sets the register (the standard asks for no start value)
// Fault: scrambles_header (the two sync header bits go through the scrambler too).
module eth_66_scr;
  bit [57:0] s = 58'd0;
  bit scrambles_header = 0;
  function automatic void load(input [57:0] v); s = v; endfunction
  function automatic bit scr_bit(input bit b);
    bit o; o = b ^ s[38] ^ s[57]; s = {s[56:0], o}; return o;
  endfunction
  function automatic bit dscr_bit(input bit b);
    bit o; o = b ^ s[38] ^ s[57]; s = {s[56:0], b}; return o;
  endfunction
  function automatic [65:0] scramble(input [65:0] blk);
    reg [65:0] o; o = blk;
    for (int i = scrambles_header ? 0 : 2; i < 66; i++) o[i] = scr_bit(blk[i]);
    return o;
  endfunction
  function automatic [65:0] descramble(input [65:0] blk);
    reg [65:0] o; o = blk;
    for (int i = 2; i < 66; i++) o[i] = dscr_bit(blk[i]);
    return o;
  endfunction
endmodule

// eth_prbs31: the PRBS31 pattern generator (49.2.8, Figure 49-9). The register is s[30:0], stage S0 is s[0].
//   gen_bit()   the next pattern bit: S27 XOR S30 shifts into S0, and the output is that bit inverted
// The register must not be all zeros: it would stay there. The checker is not in this file.
module eth_prbs31;
  bit [30:0] s = 31'h7fffffff;
  function automatic bit gen_bit();
    bit f; f = s[27] ^ s[30]; s = {s[29:0], f}; return !f;
  endfunction
endmodule

// eth_66_test: the square wave of 49.2.8 and the two data patterns of the pseudo-random test pattern.
//   sq_bit()        square wave: sq_n ones, then sq_n zeros (sq_n may be 4 to 11)
//   pattern()       the 64-bit data pattern: zeros, or the payload of a block with two local fault sets (lf_pattern)
// The pseudo-random pattern generator and its checker (49.2.8, 49.2.12) are not in this file.
module eth_66_test;
  eth_66 code();
  bit lf_pattern = 0;
  int sq_n = 8, sq_k = 0;
  function automatic void restart(); sq_k = 0; endfunction
  function automatic bit sq_bit();
    bit b; b = (sq_k < sq_n); sq_k = (sq_k + 1) % (2 * sq_n); return b;
  endfunction
  function automatic [63:0] pattern();
    reg [66:0] r;
    if (!lf_pattern) return 64'd0;
    r = code.enc_ctrl({64'h0100009c_0100009c, 8'h11}); return r[65:2];
  endfunction
endmodule

// eth_66_loop: PCS loopback (49.2.14.4), switched by MDIO bit 3.0.14.
//   rx_block(from_tx, from_pma)   what the receive path decodes: its own transmit block when loopback is 1
//   pma_word(w)                   what goes to the PMA: the word 00FFh when loopback is 1, else w
module eth_66_loop;
  bit loopback = 0;
  function automatic [65:0] rx_block(input [65:0] from_tx, input [65:0] from_pma); return loopback ? from_tx : from_pma; endfunction
  function automatic [15:0] pma_word(input [15:0] w); return loopback ? 16'h00ff : w; endfunction
endmodule
ConceptA checker gets 256 blocks of the pseudo-random pattern. Payload bit 38 (block bit 40) of block 5 is flipped on the line. What does the error counter read?
ConceptHow often is the scrambler loaded with a seed in the pseudo-random pattern?
ConceptWhich test pattern is meant for transmitter tests only?
ConceptOne isolated line bit is wrong in a PRBS31 test. How many times does the error signal go high?
ConceptA 10GBASE-R PCS is in loopback. What does it send to the PMA?

Common Mistakes

Wrong Count every mismatching block of the pseudo-random pattern as an error.

Each seed load breaks one block. A perfect link would show one error per 128 blocks.

Fix Skip the first mismatch of each 128-block window. Count the rest.

Wrong Read the PRBS31 error counter as the number of wrong bits.

The checker flags an isolated wrong bit three times.

Fix Divide by three, and only when errors are rare. Close errors share tests and give fewer flags.

Wrong Give the Clause 49 checker its own free-running generator.

G6.10 showed that design, and it flags a wrong bit once. But the standard fixes the result: three flags.

Fix Keep the last 31 received bits, as Figure 49-11 does, and test each new bit against two of them.

Wrong Leave the transmitter silent in loopback.

The standard asks for a steady stream of 00FFh words while loopback is on (49.2.14.4).

Fix Send the word 00FFh to the PMA for as long as loopback is on.

Remember

  • A 10GBASE-R PCS must have the square wave and the pseudo-random pattern. PRBS31 is optional.
  • The pseudo-random pattern reloads the scrambler every 128 blocks: seed A, A inverted, B, B inverted.
  • Its checker expects one mismatch per 128 blocks and counts only the others.
  • The PRBS31 checker is self-synchronising. One wrong bit raises its error signal three times.
  • In loopback the transmit data returns on the receive path, and the PMA gets 00FFh.

Practice

Report a problem with this page