Block Lock, Scrambler and the BER Monitor

The receiver gets bits, not blocks. See how it finds the block boundary and when it gives it up. Then see how it decides that a link is too noisy.

You Will Be Able To

  • Trace the lock state diagram with its two counts, 64 and 16.
  • Explain why the sync header is not scrambled, and what one bit error costs.
  • Work out when the BER monitor sets and clears hi_ber.
  • Say what the receiver does when it has no lock or a high error ratio.
Lesson
P11.24
Time
35 min
Runs on
Your browser
Check
5 questions

P10.4 showed how a receiver hunts for the two-bit sync header. Clause 49 fixes the counts. Watch them decide.

Fifteen Broken Headers, or SixteenThree runs of 200 blocks through a locked receiver. Only the broken sync headers differ.
012broken headers15 in one window16 in one window15 + 15 in two windowslock lostneveronceneverat the endin lockout of lockin lock
Scroll horizontally ↔
  1. Cycle 0

    A window is 64 sync headers. Fifteen bad ones in a window do nothing to lock.

  2. Cycle 1

    The sixteenth bad header in one window drops lock. The receiver starts to hunt again.

  3. Cycle 2

    Thirty bad headers in a row, but split 15 and 15 over two windows. Lock holds.

Bench run of the example: hs_blk_lock of P10.4 with the counts of Clause 49.

Finding the Block Boundary

The PMA hands the PCS a stream of bits. The block synchronization process must find where each 66-bit block starts (49.2.9).

It has one clue. The first two bits of a block always differ: 01 or 10. Scrambled payload bits differ only half the time.

The Lock State DiagramOne pass per sync header. Two counters run over a window of 64 headers: all headers, and invalid ones.
  • Control / FSM
  • Control
The lock state diagramOne pass per sync header. Two counters run over a window of 64 headers: all headers, and invalid ones. control RESET_CNT both counters to 0 control TEST_SH test this header control VALID_SH header count + 1 control INVALID_SH both counts + 1 control 64_GOOD block lock = true control SLIP block lock = false;move one bit header ready01 or 1000 or 11fewer than 6464, none invalid64, some invalidin lock, under 16,under 64in lock, under 16, 6416 invalid, or not inlockslip done
  1. control TEST_SHtest this header
    • 01 or 10 → VALID_SH
    • 00 or 11 → INVALID_SH
  2. control INVALID_SHboth counts + 1
    • in lock, under 16, under 64 → TEST_SH
    • in lock, under 16, 64 → RESET_CNT
    • 16 invalid, or not in lock → SLIP
  3. control SLIPblock lock = false; move one bit
    • slip done → RESET_CNT
  4. control RESET_CNTboth counters to 0
    • header ready → TEST_SH
  5. control VALID_SHheader count + 1
    • fewer than 64 → TEST_SH
    • 64, none invalid → 64_GOOD
    • 64, some invalid → RESET_CNT
  6. control 64_GOODblock lock = true
    • RESET_CNT
  1. Hunting

    Out of lock, one invalid header is enough. The receiver slips one bit and counts again from zero.

  2. Locking

    Sixty-four valid headers in one window set block lock.

  3. Holding

    In lock, a window with 1 to 15 invalid headers changes nothing. The counters start again.

  4. Losing

    The sixteenth invalid header of a window clears block lock at once. The hunt starts again.

Read the diagram as text
  • RESET_CNT: both counters to 0
  • TEST_SH: test this header
  • VALID_SH: header count + 1
  • INVALID_SH: both counts + 1
  • 64_GOOD: block lock = true
  • SLIP: block lock = false; move one bit
  • RESET_CNT → TEST_SH: header ready
  • TEST_SH → VALID_SH: 01 or 10
  • TEST_SH → INVALID_SH: 00 or 11
  • VALID_SH → TEST_SH: fewer than 64
  • VALID_SH → 64_GOOD: 64, none invalid
  • VALID_SH → RESET_CNT: 64, some invalid
  • INVALID_SH → TEST_SH: in lock, under 16, under 64
  • INVALID_SH → RESET_CNT: in lock, under 16, 64
  • INVALID_SH → SLIP: 16 invalid, or not in lock
  • 64_GOOD → RESET_CNT
  • SLIP → RESET_CNT: slip done

After IEEE Std 802.3-2022 Figure 49-14 (redrawn; LOCK_INIT, entered on reset or loss of signal, is left out).

A header is valid if its two bits differ (49.2.13.2.2). The process tests one header per block.

Out of lock, any invalid header means the guess was wrong. The process slips one bit and starts its count again.

The example started 17 bits into a block. It needed 49 slips, and lock came after 10,873 bits.

Most wrong positions fail fast. Then the right one must show 64 valid headers in a row.

Keeping Lock, and Losing It

In lock the rule is far more patient. Line errors break a header now and then. That must not cost the link.

The process counts in windows of 64 headers. Sixteen invalid headers in one window clear block lock (Figure 49-14).

The windows do not slide. Each one starts where the last one ended, so 15 and 15 in two windows do no harm.

P10.4 built this receiver as hs_blk_lock. Its default counts are the ones of Clause 49.

RunClean receiverWith lock_on_first
Start 17 bits into a block49 slips, lock after 10,873 bits3 slips, lock after 267 bits
The rest of that runlock keptlock lost 5 times
15 broken headers in one windowlock keptlock kept
16 broken headers in one windowlock lost oncelock lost 4 times
15 at the end of a window, 15 at the start of the nextlock keptlock lost 3 times

Bench runs of the example and of its twin. 200 scrambled idle blocks each; the last three runs start on a block boundary.

The twin lock_on_first trusts a single valid header. So it locks at a wrong position, where half the headers look valid.

It then loses lock again and again. That is why the standard asks for 64 in a row.

The Scrambler and the Descrambler

The payload goes through the self-synchronising scrambler of P10.5 (49.2.6). Its polynomial is 1 + x^39 + x^58.

Each line bit is the payload bit XOR two older line bits: the ones sent 39 and 58 bits before.

The two sync header bits bypass the scrambler. The example shows why.

ScramblerValid sync headersBlock lock
header bypasses the scrambler200 of 200reached
with scrambles_header110 of 200never reached

Bench run: eth_66_scr and its twin, 200 idle blocks into hs_blk_lock.

A scrambled header looks like any other bit pair. The receiver has nothing left to lock to.

The descrambler undoes the XOR with the bits it received (49.2.10). The standard asks for no start value.

What happenedWrong bits, first blockWrong bits, next block
The descrambler started with other contents290
One line bit was flipped21

Bench run of the example with eth_66_scr: scrambled idle blocks, compared after the descrambler.

With the wrong contents, only the first block came out wrong. After 58 line bits the register holds what the sender's holds.

A flipped line bit is worse: 3 wrong payload bits. It is wrong once itself, and twice more as an older bit.

The BER Monitor

Block lock can hold on a very noisy line. So a second process watches the same headers: the BER monitor (Figure 49-15).

The BER MonitorA timer of 125 µs and one counter. Sixteen invalid headers before the timer ends set hi_ber.
  • Control / FSM
  • Control
The BER monitorA timer of 125 µs and one counter. Sixteen invalid headers before the timer ends set hi_ber. control START_TIMER count = 0; start 125µs control BER_TEST_SH look at each header control BER_BAD_SH count + 1 control HI_BER hi_ber = true control GOOD_BER hi_ber = false header readyinvalidvalid, timer doneunder 16, timerrunningunder 16, timer donecount is 16timer done
  1. control BER_TEST_SHlook at each header
    • invalid → BER_BAD_SH
    • valid, timer done → GOOD_BER
  2. control BER_BAD_SHcount + 1
    • under 16, timer running → BER_TEST_SH
    • under 16, timer done → GOOD_BER
    • count is 16 → HI_BER
  3. control GOOD_BERhi_ber = false
    • START_TIMER
  4. control START_TIMERcount = 0; start 125 µs
    • header ready → BER_TEST_SH
  5. control HI_BERhi_ber = true
    • timer done → START_TIMER
  1. Count

    Each invalid sync header adds one to the count. Valid headers add nothing.

  2. A good period

    The timer ends with fewer than 16. hi_ber is cleared and a new period starts.

  3. A bad period

    The count reaches 16. hi_ber is set at once. The monitor waits there for the timer.

  4. Coming back

    HI_BER does not clear hi_ber. Only the end of a later good period does.

Read the diagram as text
  • START_TIMER: count = 0; start 125 µs
  • BER_TEST_SH: look at each header
  • BER_BAD_SH: count + 1
  • HI_BER: hi_ber = true
  • GOOD_BER: hi_ber = false
  • START_TIMER → BER_TEST_SH: header ready
  • BER_TEST_SH → BER_BAD_SH: invalid
  • BER_TEST_SH → GOOD_BER: valid, timer done
  • BER_BAD_SH → BER_TEST_SH: under 16, timer running
  • BER_BAD_SH → GOOD_BER: under 16, timer done
  • BER_BAD_SH → HI_BER: count is 16
  • HI_BER → START_TIMER: timer done
  • GOOD_BER → START_TIMER

After IEEE Std 802.3-2022 Figure 49-15 (redrawn; BER_MT_INIT, entered on reset, test mode or loss of block lock, is left out).

It counts invalid headers while a 125 µs timer runs. Sixteen of them set hi_ber (49.2.13.2.2).

The timer may run from 93.75 µs to 126.25 µs: the standard allows +1% and −25% (49.2.13.2.5).

Invalid headershi_ber
15 invalid headers in one periodstays 0
16 invalid headers in one period, then cleanrises at header 1,600, falls at header 39,062
8 at the end of a period, 8 at the start of the nextstays 0
16, 16, then 15, then cleanrises at header 1,600, falls at header 58,593
25GBASE-R counts, 96 invalid headers in one periodstays 0
25GBASE-R counts, 97 invalid headers in one periodrises at header 9,700, falls at header 1,562,500

Bench runs of a private monitor model. Bench choice: a period is counted in headers, not in time: 19,531 for 10GBASE-R and 781,250 for 25GBASE-R.

Look at the second row. hi_ber rose at the 16th invalid header. It fell at the end of the next period, which had fewer than 16.

So hi_ber never drops in the middle of a period. A noisy link stays marked until a whole period ends with fewer than 16.

Why 16? In 125 µs a 10GBASE-R link carries about 19,531 headers. A header breaks when one of its two bits is wrong.

At a bit error ratio of 10^-4, about 3.9 headers break per period. Sixteen is the average near 4.1 × 10^-4.

That is arithmetic for independent bit errors. The standard itself says hi_ber shows a ratio above 10^-4.

What Lock and hi_ber Feed

The receive state diagram of P11.23 starts over when block lock is false or hi_ber is true. It then sends local fault to the XGMII.

The MAC side sees that as a link fault (P11.19). So a noisy link is taken down, not left to deliver bad frames.

The status PCS_status is true only with block lock and without hi_ber (49.2.14.1). MDIO shows it as bit 3.32.12.

Block lock is bit 3.32.0, and hi_ber is bit 3.32.1. A 6-bit counter in 3.33.13:8 counts the invalid headers the monitor saw (49.2.14.2).

The monitor itself restarts on reset, in test-pattern mode and without block lock. Test patterns are the subject of P11.25.

Other rates keep the diagram and change two numbers.

PCSLimitPeriodSync headers in a period
10GBASE-R16125 µs19,531.25
25GBASE-R972 ms781,250
5GBASE-R16250 µs781,250

Limits and periods: IEEE Std 802.3-2022 49.2.13.2.2, 107.1.2 and 129.1.2. The header counts are bench arithmetic from the line rates.

The 25GBASE-R PCS is the Clause 49 PCS with a limit of 97 in 2 ms (107.1.2). The 5GBASE-R PCS keeps 16 and uses 250 µs (129.1.2).

Try It

The bench scrambles idle blocks onto a line of bits. hs_blk_lock takes the bits one at a time.

The first two lines show the hunt from a wrong start. The next three break sync headers in a locked receiver.

The last two lines are about the descrambler: a wrong start heals in one block, and one flipped bit costs three.

The twin is one more line, lk.lock_on_first = 1; after lk.use_66();. The table above shows what it does.

Change receive(17) to receive(40). Predict the number of slips before you run it.

RUNIcarus Verilog · in your browser
Edit the code, then run it
Expected: start 17 bits into a block: first lock after 49 slips and 10873 bits the same run to its end: lock lost 0 time(s) 15 broken headers in one window: lock lost 0 time(s), in lock at the end 16 broken headers in one window: lock lost 1 time(s), out of lock at the end 15 at the end of a window, 15 at the start of the next: lock lost 0 time(s), in lock at the end descrambler started wrong: 29 wrong bits in block 0, 0 in block 1 one line bit flipped: 2 wrong bits in block 0, 1 in block 1
Read included file: hs_pkg.sv
`timescale 1ns/1ns
// hs_pkg.sv: shared pure functions, and the bench random generator (read-only).
package hs_pkg;
  // xorshift32 (Marsaglia 2003): a linear generator over GF(2), period 2^32 - 1. A zero state is
  // replaced by 1, because zero maps to itself.
  function automatic [31:0] xs32(input [31:0] s);
    reg [31:0] x;
    x = (s == 32'd0) ? 32'd1 : s;
    x = x ^ (x << 13); x = x ^ (x >> 17); x = x ^ (x << 5);
    return x;
  endfunction
  // A Fibonacci PRBS generator x^n + x^m + 1 (PRBS7: 7,6; PRBS9: 9,5; PRBS15: 15,14; PRBS23: 23,18;
  // PRBS31: 31,28). The output bit is s[n-1]; the next state shifts the feedback into bit 0.
  function automatic [31:0] prbs_next(input [31:0] s, input int n, input int m);
    reg fb;
    fb = s[n-1] ^ s[m-1];
    return ((s << 1) | {31'd0, fb}) & ((n == 32) ? 32'hffffffff : ((32'd1 << n) - 32'd1));
  endfunction
  function automatic int ones(input [63:0] v);
    int n; n = 0;
    for (int i = 0; i < 64; i++) n += v[i];
    return n;
  endfunction
  // GF(16) with x^4 + x + 1, and GF(1024) with x^10 + x^3 + 1: shift-and-add multiply, no tables.
  function automatic [3:0] gf16_mul(input [3:0] a, input [3:0] b);
    reg [3:0] p, x; p = 4'd0; x = a;
    for (int i = 0; i < 4; i++) begin
      if (b[i]) p = p ^ x;
      x = x[3] ? ({x[2:0], 1'b0} ^ 4'b0011) : {x[2:0], 1'b0};
    end
    return p;
  endfunction
  function automatic [3:0] gf16_pow(input int e);   // alpha^e, alpha = x
    reg [3:0] p; int k; p = 4'd1; k = e % 15; if (k < 0) k += 15;
    for (int i = 0; i < k; i++) p = gf16_mul(p, 4'd2);
    return p;
  endfunction
  function automatic int gf16_log(input [3:0] a);   // -1 for 0
    reg [3:0] p; p = 4'd1;
    if (a == 4'd0) return -1;
    for (int i = 0; i < 15; i++) begin if (p == a) return i; p = gf16_mul(p, 4'd2); end
    return -1;
  endfunction
  function automatic [9:0] gf1024_mul(input [9:0] a, input [9:0] b);
    reg [9:0] p, x; p = 10'd0; x = a;
    for (int i = 0; i < 10; i++) begin
      if (b[i]) p = p ^ x;
      x = x[9] ? ({x[8:0], 1'b0} ^ 10'b0000001001) : {x[8:0], 1'b0};
    end
    return p;
  endfunction
  function automatic [9:0] gf1024_pow(input int e);
    reg [9:0] p; int k; p = 10'd1; k = e % 1023; if (k < 0) k += 1023;
    for (int i = 0; i < k; i++) p = gf1024_mul(p, 10'd2);
    return p;
  endfunction
endpackage

// hs_rng: the bench's random numbers. Same seed, same numbers, on every engine.
module hs_rng;
  int unsigned s = 32'h2545f491;
  function automatic void seed(input int unsigned v); s = (v == 0) ? 32'd1 : v; endfunction
  function automatic int unsigned next(); s = hs_pkg::xs32(s); return s; endfunction
  function automatic int below(input int n); s = hs_pkg::xs32(s); return (n <= 0) ? 0 : int'(s % n); endfunction
  function automatic bit bit1(); s = hs_pkg::xs32(s); return s[16]; endfunction
  function automatic bit chance_ppm(input int ppm); s = hs_pkg::xs32(s); return (s % 1000000) < ppm; endfunction
  function automatic [7:0] byte8(); s = hs_pkg::xs32(s); return s[23:16]; endfunction
endmodule
Read included file: hs_code.sv
`timescale 1ns/1ns
// hs_code.sv: line codes, CRCs and scramblers (read-only).

// ---------------------------------------------------------------------------------------------
// hs_8b10b: 8b/10b encoder and decoder with running disparity and the 12 K codes.
// code[9:0] = {a,b,c,d,e,i,f,g,h,j}; bit a (code[9]) goes on the wire first. rd: 0 = RD-, 1 = RD+.
//   encode(d, k, rd_in) -> {rd_out, code[9:0]}            (11 bits)
//   decode(code, rd_in) -> {rd_out, disp_err, code_err, k, d[7:0]}   (12 bits)
//   enc(d, k) / dec(code): the same, with the running disparity kept in rd_tx / rd_rx
// A K request for a byte that is not one of the 12 K codes is encoded as data and counted in bad_k.
// Decoder: code_err = the code is in neither column of the table; disp_err = it is a valid code
// only in the other column. rd_out follows the sub-block rule on the received bits.
// Faults: no_rd (always the RD- column), a7_never (never the alternate D.x.A7),
//         keep_rd_on_unbalanced (the 4b sub-block is chosen with the disparity from before the 6b one),
//         no_balanced_flip (D.07 and D.x.3 keep their RD- form at RD+), dec_no_disp_check.
module hs_8b10b;
  bit no_rd = 0, a7_never = 0, keep_rd_on_unbalanced = 0, no_balanced_flip = 0, dec_no_disp_check = 0;
  bit trace = 0;
  bit rd_tx = 0, rd_rx = 0;
  int bad_k = 0, symbols = 0, code_errs = 0, disp_errs = 0;
  bit last_k = 0, last_code_err = 0, last_disp_err = 0;
  bit valid_m [0:1023]; bit valid_p [0:1023]; bit [8:0] kd [0:1023]; bit built = 0;
  function automatic [5:0] t6(input [4:0] x);   // 5b/6b, RD- column, abcdei
    case (x)
      5'd0: return 6'b100111;  5'd1: return 6'b011101;  5'd2: return 6'b101101;  5'd3: return 6'b110001;
      5'd4: return 6'b110101;  5'd5: return 6'b101001;  5'd6: return 6'b011001;  5'd7: return 6'b111000;
      5'd8: return 6'b111001;  5'd9: return 6'b100101;  5'd10: return 6'b010101; 5'd11: return 6'b110100;
      5'd12: return 6'b001101; 5'd13: return 6'b101100; 5'd14: return 6'b011100; 5'd15: return 6'b010111;
      5'd16: return 6'b011011; 5'd17: return 6'b100011; 5'd18: return 6'b010011; 5'd19: return 6'b110010;
      5'd20: return 6'b001011; 5'd21: return 6'b101010; 5'd22: return 6'b011010; 5'd23: return 6'b111010;
      5'd24: return 6'b110011; 5'd25: return 6'b100110; 5'd26: return 6'b010110; 5'd27: return 6'b110110;
      5'd28: return 6'b001110; 5'd29: return 6'b101110; 5'd30: return 6'b011110; default: return 6'b101011;
    endcase
  endfunction
  function automatic [3:0] t4d(input [2:0] y);  // 3b/4b data, RD- column, fghj (y = 7 is P7)
    case (y)
      3'd0: return 4'b1011; 3'd1: return 4'b1001; 3'd2: return 4'b0101; 3'd3: return 4'b1100;
      3'd4: return 4'b1101; 3'd5: return 4'b1010; 3'd6: return 4'b0110; default: return 4'b1110;
    endcase
  endfunction
  function automatic [3:0] t4k(input [2:0] y);  // 3b/4b for K codes, RD- form before the flip
    case (y)
      3'd0: return 4'b1011; 3'd1: return 4'b0110; 3'd2: return 4'b1010; 3'd3: return 4'b1100;
      3'd4: return 4'b1101; 3'd5: return 4'b0101; 3'd6: return 4'b1001; default: return 4'b0111;
    endcase
  endfunction
  function automatic bit k_ok(input [7:0] d);
    return d[4:0] == 5'd28 || d == 8'hf7 || d == 8'hfb || d == 8'hfd || d == 8'hfe;
  endfunction
  function automatic int n6(input [5:0] v); return v[0] + v[1] + v[2] + v[3] + v[4] + v[5]; endfunction
  function automatic int n4(input [3:0] v); return v[0] + v[1] + v[2] + v[3]; endfunction
  // running disparity at the end of a sub-block (more ones: +; more zeros: -; 000111 and 0011: +; 111000 and 1100: -)
  function automatic bit rd6(input [5:0] v, input bit rd);
    return (n6(v) > 3) ? 1'b1 : (n6(v) < 3) ? 1'b0 : (v == 6'b000111) ? 1'b1 : (v == 6'b111000) ? 1'b0 : rd;
  endfunction
  function automatic bit rd4(input [3:0] v, input bit rd);
    return (n4(v) > 2) ? 1'b1 : (n4(v) < 2) ? 1'b0 : (v == 4'b0011) ? 1'b1 : (v == 4'b1100) ? 1'b0 : rd;
  endfunction
  // faults: [0] no_rd [1] a7_never [2] keep_rd_on_unbalanced [3] no_balanced_flip
  function automatic [10:0] core(input [7:0] d, input bit k, input bit rd_in, input [3:0] f);
    reg [5:0] six; reg [3:0] four; reg rd0, r6, rd1, a7, kk; reg [4:0] x; reg [2:0] y; int o6, o4;
    x = d[4:0]; y = d[7:5]; kk = k && k_ok(d); rd0 = f[0] ? 1'b0 : rd_in;
    six = (kk && x == 5'd28) ? 6'b001111 : t6(x); o6 = n6(six);
    if (rd0 && (o6 != 3 || (six == 6'b111000 && !f[3]))) begin six = ~six; o6 = 6 - o6; end
    r6 = (o6 > 3) ? 1'b1 : (o6 < 3) ? 1'b0 : (six == 6'b000111) ? 1'b1 : (six == 6'b111000) ? 1'b0 : rd0;
    rd1 = f[2] ? rd0 : r6;
    if (kk) begin
      four = t4k(y); if (rd1) four = ~four;
    end else begin
      a7 = (y == 3'd7) && !f[1] && ((!rd1 && (x == 5'd17 || x == 5'd18 || x == 5'd20)) || (rd1 && (x == 5'd11 || x == 5'd13 || x == 5'd14)));
      four = a7 ? 4'b0111 : t4d(y);
      if (rd1 && (n4(four) != 2 || (four == 4'b1100 && !f[3]))) four = ~four;
    end
    o4 = n4(four);
    return {(o4 > 2) ? 1'b1 : (o4 < 2) ? 1'b0 : (four == 4'b0011) ? 1'b1 : (four == 4'b1100) ? 1'b0 : r6, six, four};
  endfunction
  function automatic [10:0] encode(input [7:0] d, input bit k, input bit rd_in);
    if (k && !k_ok(d)) bad_k++;
    return core(d, k, rd_in, {no_balanced_flip, keep_rd_on_unbalanced, a7_never, no_rd});
  endfunction
  function automatic void build();
    reg [10:0] c;
    for (int i = 0; i < 1024; i++) begin valid_m[i] = 0; valid_p[i] = 0; kd[i] = 9'd0; end
    for (int i = 0; i < 268; i++) begin
      reg [7:0] d; reg k;
      if (i < 256) begin d = i[7:0]; k = 0; end
      else begin k = 1; d = (i < 264) ? {3'(i - 256), 5'd28} : (i == 264) ? 8'hf7 : (i == 265) ? 8'hfb : (i == 266) ? 8'hfd : 8'hfe; end
      c = core(d, k, 1'b0, 4'd0); valid_m[c[9:0]] = 1; kd[c[9:0]] = {k, d};
      c = core(d, k, 1'b1, 4'd0); valid_p[c[9:0]] = 1; kd[c[9:0]] = {k, d};
    end
    built = 1;
  endfunction
  function automatic [11:0] decode(input [9:0] code, input bit rd_in);
    reg here, there, ce, de, r;
    if (!built) build();
    here = rd_in ? valid_p[code] : valid_m[code];
    there = rd_in ? valid_m[code] : valid_p[code];
    ce = !(here || there); de = !ce && !here && !dec_no_disp_check;
    r = rd4(code[3:0], rd6(code[9:4], rd_in));
    return {r, de, ce, ce ? 9'd0 : kd[code]};
  endfunction
  function automatic [9:0] enc(input [7:0] d, input bit k);
    reg [10:0] r; r = encode(d, k, rd_tx); rd_tx = r[10];
    if (trace) $display("s%0d TX %s%0d.%0d code=%b rd=%s", symbols, (k && k_ok(d)) ? "K" : "D", d[4:0], d[7:5], r[9:0], r[10] ? "+" : "-");
    symbols++;
    return r[9:0];
  endfunction
  function automatic [8:0] dec(input [9:0] code);
    reg [11:0] r; r = decode(code, rd_rx); rd_rx = r[11];
    last_disp_err = r[10]; last_code_err = r[9]; last_k = r[8];
    if (r[9]) code_errs++; if (r[10]) disp_errs++;
    if (trace && (r[9] || r[10])) $display("RX %b %s", code, r[9] ? "code error" : "disparity error");
    return r[8:0];
  endfunction
  function automatic bit comma7(input [6:0] w); return w == 7'b0011111 || w == 7'b1100000; endfunction
endmodule

// ---------------------------------------------------------------------------------------------
// hs_crc: a CRC of 1 to 32 bits with any polynomial, seed, bit order and final inversion.
// The register shifts left; the polynomial omits the x^width term. The field is sent register bit
// width-1 first (USB 2.0, USB 3.2 and Ethernet all send it this way).
//   use_crc32(), use_crc16_usb2(), use_crc5_usb2(), use_crc16_usb3(): parameter sets
//   reset(), crc_bit(b), crc_byte(v), crc_bits(v, n), field(), field_bit(i), check_value(), crc_residue_ok()
// Faults: msb_first (bytes enter MSB first), no_invert (the field is not complemented), seed_zero.
module hs_crc;
  int width = 32;
  bit [31:0] poly = 32'h04c11db7, seed = 32'hffffffff, residue = 32'hc704dd7b;
  bit lsb_first = 1, invert = 1;
  bit msb_first = 0, no_invert = 0, seed_zero = 0;
  bit [31:0] r = 32'hffffffff;
  function automatic [31:0] mask(); return (width >= 32) ? 32'hffffffff : ((32'd1 << width) - 32'd1); endfunction
  function automatic void reset(); r = seed_zero ? 32'd0 : (seed & mask()); endfunction
  function automatic void set(input int w, input [31:0] p, input [31:0] s, input [31:0] res, input bit lsb, input bit inv);
    width = w; poly = p; seed = s; residue = res; lsb_first = lsb; invert = inv; reset();
  endfunction
  function automatic void use_crc32();      set(32, 32'h04c11db7, 32'hffffffff, 32'hc704dd7b, 1, 1); endfunction
  function automatic void use_crc16_usb2(); set(16, 32'h8005, 32'hffff, 32'h800d, 1, 1); endfunction
  function automatic void use_crc5_usb2();  set(5, 32'h05, 32'h1f, 32'h0c, 1, 1); endfunction
  function automatic void use_crc16_usb3(); set(16, 32'h100b, 32'hffff, 32'hf6aa, 1, 1); endfunction
  function automatic void crc_bit(input bit b);
    reg fb; fb = b ^ r[width - 1];
    r = ((r << 1) ^ (fb ? poly : 32'd0)) & mask();
  endfunction
  function automatic void crc_byte(input [7:0] v);
    for (int i = 0; i < 8; i++) crc_bit(v[(lsb_first ^ msb_first) ? i : 7 - i]);
  endfunction
  function automatic void crc_bits(input [31:0] v, input int n);   // n bits of v, bit 0 first
    for (int i = 0; i < n; i++) crc_bit(v[i]);
  endfunction
  function automatic [31:0] field(); return (invert && !no_invert) ? (~r & mask()) : r; endfunction
  function automatic bit field_bit(input int i); reg [31:0] f; f = field(); return f[width - 1 - i]; endfunction
  // the usual published "check" number: the field with its first-sent bit read as bit 0
  function automatic [31:0] check_value();
    reg [31:0] f, o; f = field(); o = 32'd0;
    for (int i = 0; i < width; i++) o[i] = f[width - 1 - i];
    return lsb_first ? o : f;
  endfunction
  function automatic bit crc_residue_ok(); return r == (residue & mask()); endfunction
endmodule

// ---------------------------------------------------------------------------------------------
// hs_scr: additive (frame-synchronous) and multiplicative (self-synchronising) scramblers.
// poly holds the coefficients: bit k is x^k; the +1 term is always used (taps() sets bit 0); len is the degree.
// Additive: a Galois LFSR. The key bit is s[len-1]; each step shifts left and adds the low terms of
//   the polynomial when the key bit is 1. The data never enters the register.
// Multiplicative: the line bit is the data bit XOR the register bits at the polynomial's terms;
//   the scrambler shifts its own output in, the descrambler shifts the received line bit in.
//   scr_add(len, poly, seed), scr_mul(len, poly), use_usb3_gen1(), use_x58(), use_x23_usb3() (see its note)
//   scr_bit(b), dscr_bit(b), scr_byte(v), dscr_byte(v) (bit 0 first), scr_reset(), scr_hold() (a skip
//   symbol: no step), scr_unscrambled() (a symbol sent in the clear: 8 steps, data untouched)
// Faults: advance_on_skip (scr_hold steps the LFSR 8 times), no_reset (scr_reset does nothing),
//         wrong_tap (the lowest term x^k becomes x^(k+1)), seed_zero (scr_reset loads 0).
module hs_scr;
  bit mult = 0; int len = 16;
  bit [63:0] poly = 64'h10039, seed = 64'hffff;
  bit advance_on_skip = 0, no_reset = 0, wrong_tap = 0, seed_zero = 0;
  bit [63:0] s = 64'hffff;
  int steps = 0;
  function automatic [63:0] lmask(); return (len >= 64) ? 64'hffffffffffffffff : ((64'd1 << len) - 64'd1); endfunction
  function automatic [63:0] taps();
    reg [63:0] p; int k; p = poly | 64'd1; k = 1;
    if (wrong_tap) begin
      while (k < len && !p[k]) k++;
      if (k < len) begin p[k] = 1'b0; p[k + 1] = 1'b1; end
    end
    return p;
  endfunction
  function automatic void load(); s = (seed_zero ? 64'd0 : seed) & lmask(); endfunction
  function automatic void scr_add(input int n, input [63:0] p, input [63:0] sd); mult = 0; len = n; poly = p; seed = sd; s = sd & lmask(); endfunction
  function automatic void scr_mul(input int n, input [63:0] p); mult = 1; len = n; poly = p; seed = 64'd0; s = 64'd0; endfunction
  function automatic void use_usb3_gen1(); scr_add(16, 64'h10039, 64'hffff); endfunction   // x^16 + x^5 + x^4 + x^3 + 1, seed FFFFh
  function automatic void use_x58(); scr_mul(58, (64'd1 << 58) | (64'd1 << 39) | 64'd1); endfunction   // x^58 + x^39 + 1
  // USB 3.2 Gen 2 (§6.3.2.3) polynomial x^23 + x^21 + x^16 + x^8 + x^5 + x^2 + 1 with seed 1DBFBCh. Only the
  // polynomial and seed are the specification's: the register form here is this library's Galois form, and
  // the reset and bypass rules of §6.3.2.3 are not modelled, so do not quote its key stream as USB's.
  function automatic void use_x23_usb3(); scr_add(23, (64'd1 << 23) | (64'd1 << 21) | (64'd1 << 16) | (64'd1 << 8) | (64'd1 << 5) | (64'd1 << 2) | 64'd1, 64'h1dbfbc); endfunction
  function automatic void scr_reset(); if (!no_reset) load(); endfunction
  function automatic bit key(); return s[len - 1]; endfunction
  function automatic void step();
    reg kb; kb = s[len - 1];
    s = ((s << 1) & lmask()) ^ (kb ? (taps() & lmask()) : 64'd0);
    steps++;
  endfunction
  // the XOR of the register bits at the polynomial's terms x^1..x^len (bit k-1 of the register for x^k)
  function automatic bit fbx(input [63:0] st); return ^(st & (taps() >> 1) & lmask()); endfunction
  function automatic bit scr_bit(input bit b);
    reg o;
    if (!mult) begin o = b ^ s[len - 1]; step(); end
    else begin o = b ^ fbx(s); s = ((s << 1) | {63'd0, o}) & lmask(); steps++; end
    return o;
  endfunction
  function automatic bit dscr_bit(input bit b);
    reg o;
    if (!mult) begin o = b ^ s[len - 1]; step(); end
    else begin o = b ^ fbx(s); s = ((s << 1) | {63'd0, b}) & lmask(); steps++; end
    return o;
  endfunction
  function automatic [7:0] scr_byte(input [7:0] v);
    reg [7:0] o; for (int i = 0; i < 8; i++) o[i] = scr_bit(v[i]); return o;
  endfunction
  function automatic [7:0] dscr_byte(input [7:0] v);
    reg [7:0] o; for (int i = 0; i < 8; i++) o[i] = dscr_bit(v[i]); return o;
  endfunction
  // a skip symbol passes unscrambled and the LFSR holds
  function automatic void scr_hold(); if (advance_on_skip && !mult) for (int i = 0; i < 8; i++) step(); endfunction
  // another symbol that is sent unscrambled (a K code other than COM and SKP): the LFSR still steps 8 times
  function automatic void scr_unscrambled(); if (!mult) for (int i = 0; i < 8; i++) step(); endfunction
endmodule
Read included file: eth_mac.sv
`timescale 1ns/1ns
// eth_frame: one MAC frame as octets, its packet as wire bits, and a bit-serial receiver.
//   pay[i]                         client data, set by the bench before build()
//   build(da, sa, lt, len)         destination, source, Length/Type, len data octets, then the FCS -> oct[0..n-1].
//                                  It adds no pad: give it 46 data octets or more. (Padding is P11.2.1's task; the
//                                  pages show the padding MAC's frames as measured tables.)
//   wire_bits(), wire_bit(i)       the packet in transmit order: preamble, SFD, frame
//   rx_start(), rx_bit(b), rx_end()  hunt for the SFD, collect octets, then parse()
//   parse()                        da, sa, lt, is_length, is_type, data_len, fcs_rx, fcs_calc, fcs_ok
// Faults: fcs_msb_first, fcs_no_invert, fcs_covers_preamble, sfd_wrong, msb_first_octets.
module eth_frame;
  localparam int MIN_FRAME = 64, MAX_BASIC = 1518, MAX_QTAG = 1522, MAX_ENVELOPE = 2000;
  bit fcs_msb_first = 0, fcs_no_invert = 0, fcs_covers_preamble = 0, sfd_wrong = 0, msb_first_octets = 0;
  hs_crc crc();
  bit [7:0] pay [0:2047];
  bit [7:0] oct [0:2047];
  int n = 0;
  bit [47:0] da = 0, sa = 0; bit [15:0] lt = 0;
  bit is_length = 0, is_type = 0, fcs_ok = 0;
  int data_len = 0;
  bit [31:0] fcs_rx = 0, fcs_calc = 0;
  // receiver state
  bit in_frame = 0; bit [7:0] hist = 0, cur = 0; int nb = 0, excess = 0, sfd_at = -1, bits_seen = 0;

  // The FCS of oct[0..len-1] as four octets: the first octet sent is in [7:0].
  function automatic [31:0] fcs_of(input int len);
    crc.use_crc32(); crc.msb_first = fcs_msb_first; crc.no_invert = fcs_no_invert; crc.reset();
    if (fcs_covers_preamble) begin
      for (int i = 0; i < 7; i++) crc.crc_byte(8'h55);
      crc.crc_byte(8'hd5);
    end
    for (int i = 0; i < len; i++) crc.crc_byte(oct[i]);
    return crc.check_value();
  endfunction

  function automatic void build(input [47:0] d, input [47:0] s, input [15:0] t, input int len);
    int k; reg [31:0] f;
    k = 0;
    for (int i = 0; i < 6; i++) begin oct[k] = d[47 - 8*i -: 8]; k++; end
    for (int i = 0; i < 6; i++) begin oct[k] = s[47 - 8*i -: 8]; k++; end
    oct[k] = t[15:8]; k++;
    oct[k] = t[7:0]; k++;
    for (int i = 0; i < len; i++) begin oct[k] = pay[i]; k++; end
    f = fcs_of(k);
    for (int i = 0; i < 4; i++) begin oct[k] = f[8*i +: 8]; k++; end
    n = k; excess = 0;
    parse();
  endfunction

  function automatic void parse();
    da = 0; sa = 0; lt = 0; is_length = 0; is_type = 0; fcs_ok = 0; data_len = 0; fcs_rx = 0; fcs_calc = 0;
    if (n >= 14) begin
      da = {oct[0], oct[1], oct[2], oct[3], oct[4], oct[5]};
      sa = {oct[6], oct[7], oct[8], oct[9], oct[10], oct[11]};
      lt = {oct[12], oct[13]};
      is_length = (lt <= 16'd1500);
      is_type = (lt >= 16'd1536);
    end
    if (n >= 18) begin
      fcs_rx = {oct[n-1], oct[n-2], oct[n-3], oct[n-4]};
      fcs_calc = fcs_of(n - 4);
      fcs_ok = (fcs_rx == fcs_calc);
      data_len = is_length ? int'(lt) : n - 18;
    end
  endfunction

  function automatic int wire_bits(); return 8 * (8 + n); endfunction
  function automatic bit wire_bit(input int i);
    int o, b; reg [7:0] v;
    o = i / 8; b = i % 8;
    if (o < 7) v = 8'h55;
    else if (o == 7) v = sfd_wrong ? 8'h55 : 8'hd5;
    else v = oct[o - 8];
    return msb_first_octets ? v[7 - b] : v[b];
  endfunction

  function automatic void rx_start();
    in_frame = 0; hist = 0; cur = 0; nb = 0; n = 0; excess = 0; sfd_at = -1; bits_seen = 0;
  endfunction
  function automatic void rx_bit(input bit b);
    bits_seen++;
    if (!in_frame) begin
      hist = {hist[6:0], b};                      // the oldest bit is hist[7]
      if (hist == 8'b10101011) begin in_frame = 1; sfd_at = bits_seen; end
    end else begin
      if (msb_first_octets) cur[7 - nb] = b; else cur[nb] = b;
      nb++;
      if (nb == 8) begin oct[n] = cur; n++; nb = 0; end
    end
  endfunction
  function automatic void rx_end(); excess = nb; parse(); endfunction
endmodule
// eth_axis: a MAC client bus in the style of AXI4-Stream (IHI 0051B 2.2 handshake, 2.5 TKEEP, 2.6 TLAST, 2.9 TUSER),
// 64 bits wide. Byte 0 of a beat is tdata[7:0] and is first in the frame (AXI4-Stream 2.4.1). Bench conventions,
// not AXI4-Stream's or 802.3's: tkeep is all ones except on the last beat, where it covers bytes 0 to k-1; one tuser
// bit (transfer-based, 2.9.1), read on the last beat only, marks a bad frame (receive) or asks the MAC to abort it
// (transmit).
//   load(n)                  beats for octets oct[0..n-1]: bd[], bk[], bl[], nbeats; bv[] = valid per cycle, ncyc
//   tx_cycles()              the transmit MAC: one beat per cycle once a frame has started. Returns 0 sent,
//                            1 underrun (tvalid fell inside the frame), 2 aborted by tuser. sent_octets, fail_cycle.
// Fault: tvalid_gap (load() leaves cycle 3 of the frame empty: the client was late with a beat).
module eth_axis;
  bit tvalid_gap = 0;
  bit [7:0] oct [0:2047];
  bit [63:0] bd [0:300]; bit [7:0] bk [0:300]; bit bl [0:300]; bit bu [0:300];
  int nbeats = 0;
  bit bv [0:301]; int bix [0:301]; int ncyc = 0;
  int sent_octets = 0, fail_cycle = -1;
  function automatic void load(input int n);
    int b, k;
    nbeats = (n + 7) / 8;
    for (b = 0; b < nbeats; b++) begin
      bd[b] = 64'd0; bk[b] = 8'd0; bl[b] = (b == nbeats - 1); bu[b] = 0;
      for (k = 0; k < 8; k++) if (8*b + k < n) begin bd[b][8*k +: 8] = oct[8*b + k]; bk[b][k] = 1'b1; end
    end
    ncyc = 0;
    for (b = 0; b < nbeats; b++) begin
      if (tvalid_gap && b == 3) begin bv[ncyc] = 0; bix[ncyc] = -1; ncyc++; end
      bv[ncyc] = 1; bix[ncyc] = b; ncyc++;
    end
  endfunction
  function automatic int tx_cycles();
    bit started; started = 0; sent_octets = 0; fail_cycle = -1;
    for (int c = 0; c < ncyc; c++) begin
      if (!bv[c]) begin
        if (started) begin fail_cycle = c; return 1; end
      end else begin
        started = 1;
        if (bl[bix[c]] && bu[bix[c]]) begin fail_cycle = c; return 2; end
        for (int k = 0; k < 8; k++) if (bk[bix[c]][k]) sent_octets++;
      end
    end
    return 0;
  endfunction
endmodule

// eth_pause: the PAUSE function of MAC Control (Annex 31B) at the station that receives PAUSE frames, in octet
// times (one octet time is 8 bit times; a pause quantum is 512 bit times = 64 octet times, 31B.2).
//   reset(), rx_pause(t, q)  a valid PAUSE frame with pause_time q ended at time t: the timer restarts (31B.3.3)
//   may_start(t)             1 when a new data frame may start at time t. A frame already started is never cut
//                            (31B.3.7). react is the bench's reaction time: frames may still start until t + react.
//   paused_until             the time the timer runs out
//   pause_octets(q, o[])     not here: build a PAUSE frame with eth_frame (DA 01-80-C2-00-00-01, 8808h, 0001h, q)
// Faults: pause_ignored, pause_adds_not_overrides (a new frame adds to the timer, and zero does not cancel),
//         slow_reaction (react = 70 quanta, over the 60 allowed at 10 Gb/s), timer_in_bits (q counts bit times).
module eth_pause;
  localparam int QUANTUM = 64;                     // octet times
  bit pause_ignored = 0, pause_adds_not_overrides = 0, slow_reaction = 0, timer_in_bits = 0;
  int react = 0, t_rx = -1, paused_until = 0;
  function automatic void reset(); t_rx = -1; paused_until = 0; endfunction
  function automatic void rx_pause(input int t, input int q);
    int len;
    if (pause_ignored) return;
    len = timer_in_bits ? (q + 7) / 8 : q * QUANTUM;
    if (pause_adds_not_overrides && paused_until > t) paused_until = paused_until + len;
    else paused_until = t + len;
    t_rx = t;
  endfunction
  function automatic bit may_start(input int t);
    int r;
    r = slow_reaction ? 70 * QUANTUM : react;
    if (t_rx < 0) return 1;
    if (t < t_rx + r) return 1;
    return t >= paused_until;
  endfunction
endmodule

// eth_pfc: priority-based flow control (Annex 31D). The frame is 802.3's; holding a priority's queue is the MAC
// Control client's job (IEEE 802.1Q, not held), so the eight timers here are a bench client, in octet times.
//   build(f_oct[], pev, times[])   not here: the bench writes opcode 01-01, the vector and eight times into eth_frame
//   reset(), rx(t, pev, tm[0..7])  for each e[n] = 1 (bit n of the vector's low octet), priority n stops until
//                                  t + 64 * time[n] (hold_end[n]); e[n] = 0 leaves priority n alone; time[n] = 0 releases it
//   blocked(n, t)                  1 while priority n is held
// Fault: pfc_wrong_priority (reads e[n] from bit 7 - n).
module eth_pfc;
  bit pfc_wrong_priority = 0;
  int hold_end [0:7];
  function automatic void reset(); for (int i = 0; i < 8; i++) hold_end[i] = 0; endfunction
  function automatic void rx(input int t, input [15:0] pev, input [127:0] tm);   // tm[16*n +: 16] = time[n]
    bit e;
    for (int n = 0; n < 8; n++) begin
      e = pfc_wrong_priority ? pev[7 - n] : pev[n];
      if (e) hold_end[n] = t + 64 * int'(tm[16*n +: 16]);
    end
  endfunction
  function automatic bit blocked(input int n, input int t); return t < hold_end[n]; endfunction
endmodule

// eth_csma_tx: one half-duplex transmitter (4.2.3.2), one call of tick() per octet time.
//   reset(), load(frame_octets)   a frame of frame_octets (DA to FCS) waits to be sent; it is padded to min_frame
//   tick(carrier)                 carrier: another station's signal is on the wire here now. Returns 1 when the
//                                 station puts an octet (packet or jam) on the wire.
//   plan[i]                       the wait, in slots, after collision i + 1. The bench sets it (default 0). This
//                                 readable station draws nothing and has no attempt limit.
//   state  0 idle, 1 defer, 2 send, 3 jam, 4 backoff, 5 sent (as far as the sender knows)
//   pkt, sent, quiet, left, attempts, late, last_start, last_r
// min_frame is 64 octets; a bench may lower it to show why it is 64. Fault: no_backoff (every wait is 0 slots).
// Deference is a bench simplification: the 12-octet quiet count restarts on any carrier, own or received, and the
// station never starts while carrier is present. 4.2.8 restarts only the first part of the gap, and then transmits
// whatever the carrier.
module eth_csma_tx;
  localparam int SLOT = 64, JAM = 4, GAP = 12, PRE = 8;   // octet times
  bit no_backoff = 0;
  int min_frame = 64;
  int plan [0:63];
  int state = 0, pkt = 0, sent = 0, quiet = GAP, left = 0, attempts = 0, late = 0, last_start = -1, last_r = 0, now = 0;
  function automatic void reset();
    state = 0; pkt = 0; sent = 0; quiet = GAP; left = 0; attempts = 0; late = 0; last_start = -1; last_r = 0; now = 0;
  endfunction
  function automatic void load(input int frame_octets);
    pkt = PRE + frame_octets;
    if (frame_octets < min_frame) pkt = PRE + min_frame;
    state = 1; attempts = 0; sent = 0; late = 0;
  endfunction
  function automatic bit tick(input bit carrier);
    bit on;
    on = 0;
    if (state == 1 && !carrier && quiet >= GAP) begin state = 2; sent = 0; last_start = now; end
    if (state == 2 && carrier) begin
      attempts++; if (sent > SLOT) late++;
      state = 3; left = JAM;
    end
    case (state)
      2: begin sent++; on = 1; if (sent == pkt) state = 5; end
      3: begin
           on = 1; left--;
           if (left == 0) begin
             last_r = no_backoff ? 0 : plan[(attempts - 1) % 64];
             left = SLOT * last_r;
             state = (left == 0) ? 1 : 4;
           end
         end
      4: begin left--; if (left == 0) state = 1; end
      default: ;
    endcase
    quiet = (carrier || on) ? 0 : ((quiet < GAP) ? quiet + 1 : GAP);
    now++;
    return on;
  endfunction
endmodule

// eth_csma: two eth_csma_tx stations, A and B, at the two ends of a wire with a one-way delay of d octet times.
//   run(fa, ready_a, fb, ready_b, tmax)   each station loads its frame (fa, fb octets) at its ready time
//   on_a[t], on_b[t]          what each station put on the wire at time t
//   ev_t[], ev_who[] (0 A, 1 B), ev_kind[], ev_v[], n_ev   the event log:
//     kind 0 starts attempt v; 1 sees a collision after v octets; 2 jam over, backs off v slots;
//     3 last octet sent (v = octets); 4 gives up after v attempts
//   delivered(i)              1 when station i's last attempt reached the far end with no overlap there
//   a.plan[], b.plan[], a.no_backoff, b.no_backoff, a.min_frame, b.min_frame: the stations' settings
module eth_csma;
  eth_csma_tx a(); eth_csma_tx b();
  int d = 10, n_ev = 0, tend = 0;
  bit on_a [0:16383]; bit on_b [0:16383];
  int ev_t [0:255]; int ev_who [0:255]; int ev_kind [0:255]; int ev_v [0:255];
  function automatic void log_ev(input int t, input int who, input int kind, input int v);
    if (n_ev < 256) begin ev_t[n_ev] = t; ev_who[n_ev] = who; ev_kind[n_ev] = kind; ev_v[n_ev] = v; n_ev++; end
  endfunction
  function automatic void note(input int t, input int who, input int s0, input int s1, input int sent0, input int att, input int r, input int sent1);
    if (s0 != 2 && s1 == 2) log_ev(t, who, 0, att + 1);
    if (s0 == 2 && (s1 == 3 || s1 == 4)) log_ev(t, who, 1, sent0);
    if (s0 == 3 && (s1 == 4 || s1 == 1)) log_ev(t, who, 2, r);
    if (s0 != 5 && s1 == 5) log_ev(t, who, 3, sent1);
    if (s0 != 6 && s1 == 6) log_ev(t, who, 4, att);
  endfunction
  function automatic void run(input int fa, input int ready_a, input int fb, input int ready_b, input int tmax);
    bit ca, cb; int sa, sb, xa, xb;
    a.reset(); b.reset(); n_ev = 0; tend = tmax;
    for (int t = 0; t < tmax; t++) begin
      if (t == ready_a) a.load(fa);
      if (t == ready_b) b.load(fb);
      ca = (t >= d) ? on_b[t - d] : 1'b0;
      cb = (t >= d) ? on_a[t - d] : 1'b0;
      sa = a.state; sb = b.state; xa = a.sent; xb = b.sent;
      on_a[t] = a.tick(ca);
      on_b[t] = b.tick(cb);
      note(t, 0, sa, a.state, xa, a.attempts, a.last_r, a.sent);
      note(t, 1, sb, b.state, xb, b.attempts, b.last_r, b.sent);
    end
  endfunction
  function automatic bit delivered(input int i);
    int s, p, u;
    if (i == 0 && a.state != 5) return 0;
    if (i == 1 && b.state != 5) return 0;
    s = (i == 0) ? a.last_start : b.last_start;
    p = (i == 0) ? a.pkt : b.pkt;
    for (int t = s; t < s + p; t++) begin
      u = t + d;
      if (u < tend && ((i == 0) ? on_b[u] : on_a[u])) return 0;
    end
    return 1;
  endfunction
endmodule

// eth_gap: how long the gap before the next Start is on a 4-lane XGMII, where Start must sit on lane 0
// (46.3.1.4). A gap counts every character from the Terminate to the last idle before Start. A packet is
// 8 + n characters (Start, six preamble octets, SFD, an n-octet frame) and starts on lane 0.
//   reset()                     DIC = 0 (the count is reset only at initialisation)
//   method                      0 deficit idle count, 1 always insert (both allowed by 46.3.1.4)
//   next_gap(n, mac_gap)        the gap after an n-octet frame when the MAC asks for mac_gap (12 or more)
//   deleted, inserted, dic      what the last call did, and the count after it
// Faults: ipg_min_only (always deletes, ignoring the bound), dic_max4 (bounds the count at 4, not 3),
//         start_any_lane (no alignment: the gap is always mac_gap).
module eth_gap;
  bit ipg_min_only = 0, dic_max4 = 0, start_any_lane = 0;
  int method = 0, dic = 0, deleted = 0, inserted = 0;
  function automatic void reset(); dic = 0; deleted = 0; inserted = 0; endfunction
  function automatic int next_gap(input int n, input int mac_gap);
    int m, top;
    deleted = 0; inserted = 0;
    m = (n + mac_gap) % 4;                       // lanes past lane 0 the next Start would land on
    if (start_any_lane || m == 0) return mac_gap;
    top = dic_max4 ? 4 : 3;
    if (method == 0 && (ipg_min_only || dic + m <= top)) begin deleted = m; dic = dic + m; end
    else begin inserted = 4 - m; if (method == 0) dic = dic - (4 - m); end
    return mac_gap - deleted + inserted;
  endfunction
endmodule
Read included file: eth_pcs.sv
`timescale 1ns/1ns
// eth_pcs.sv: the 1000BASE-X PCS, transmit side and synchronization (read-only). It sits on hs_8b10b (hs_code.sv).

// eth_1000x: the transmit ordered-set layer (36.2.4). The stream is kept as {k, d} and as ten coded bits.
//   clear()            empty stream, running disparity negative
//   idle(k)            k idle ordered sets. Each tests the running disparity first (Figure 36-6):
//                      positive -> /I1/ (K28.5 D5.6), negative -> /I2/ (K28.5 D16.2)
//   cfg(word, k)       k configuration ordered sets, /C1/ and /C2/ in turn: K28.5, D21.5 or D2.2, word[7:0], word[15:8]
//   start_packet()     /S/ in place of the first preamble octet, then six 55h and D5h
//   data(d)            one data code-group
//   end_packet()       /T/ /R/, and one more /R/ when the first /R/ went out on an even position
//   err()              /V/
//   put(k, d)          any code-group
//   n                  code-groups so far; code-group i is even-numbered when i is even
//   sym[i] = {k, d};  code[i] = abcdei fghj, bit a (code[i][9]) is sent first;  rdb[i] = running disparity before i
//   is_k(i, d), comma_plus(), comma_minus()
// Fault: idle_wrong_disparity (every idle is /I2/, so a positive running disparity is never corrected).
module eth_1000x;
  bit idle_wrong_disparity = 0;
  hs_8b10b c8();
  bit [8:0] sym [0:8191]; bit [9:0] code [0:8191]; bit rdb [0:8191];
  int n = 0; bit c2 = 0;
  function automatic void clear(); n = 0; c2 = 0; c8.rd_tx = 0; endfunction
  function automatic void put(input bit k, input [7:0] d);
    sym[n] = {k, d}; rdb[n] = c8.rd_tx; code[n] = c8.enc(d, k); n++;
  endfunction
  function automatic void idle(input int k);
    bit positive;
    for (int i = 0; i < k; i++) begin
      positive = c8.rd_tx && !idle_wrong_disparity;
      put(1'b1, 8'hbc);                                // K28.5
      put(1'b0, positive ? 8'hc5 : 8'h50);             // D5.6 or D16.2
    end
  endfunction
  function automatic void cfg(input [15:0] word, input int k);
    for (int i = 0; i < k; i++) begin
      put(1'b1, 8'hbc);
      put(1'b0, c2 ? 8'h42 : 8'hb5);                   // D2.2 or D21.5
      put(1'b0, word[7:0]); put(1'b0, word[15:8]);
      c2 = !c2;
    end
  endfunction
  function automatic void data(input [7:0] d); put(1'b0, d); endfunction
  function automatic void start_packet();
    put(1'b1, 8'hfb);                                  // /S/ = K27.7
    for (int i = 0; i < 6; i++) put(1'b0, 8'h55);
    put(1'b0, 8'hd5);
  endfunction
  function automatic void end_packet();
    put(1'b1, 8'hfd);                                  // /T/ = K29.7
    put(1'b1, 8'hf7);                                  // /R/ = K23.7
    if (n % 2 != 0) put(1'b1, 8'hf7);                  // that /R/ was even-numbered: one more
  endfunction
  function automatic void err(); put(1'b1, 8'hfe); endfunction     // /V/ = K30.7
  function automatic bit is_k(input int i, input [7:0] d); return sym[i] == {1'b1, d}; endfunction
  function automatic int comma_plus();
    int c; c = 0;
    for (int i = 0; i < n; i++) if (code[i][9:3] == 7'b0011111) c++;
    return c;
  endfunction
  function automatic int comma_minus();
    int c; c = 0;
    for (int i = 0; i < n; i++) if (code[i][9:3] == 7'b1100000) c++;
    return c;
  endfunction
endmodule

// eth_1000x_sync: the synchronization process of Figure 36-9, one call of rx() per ten-bit code-group.
//   reset()            LOSS_OF_SYNC
//   rx(code)           takes one code-group; returns sync_status (1 = OK)
//   state              0 LOSS_OF_SYNC, 1 COMMA_DETECT_1, 2 ACQUIRE_SYNC_1, 3 COMMA_DETECT_2, 4 ACQUIRE_SYNC_2,
//                      5 COMMA_DETECT_3, 6 SYNC_ACQUIRED_1, 7 SYNC_ACQUIRED_2, 8 SYNC_ACQUIRED_2A,
//                      9 SYNC_ACQUIRED_3, 10 SYNC_ACQUIRED_3A, 11 SYNC_ACQUIRED_4, 12 SYNC_ACQUIRED_4A
//   even               the code-group just taken was even-numbered
//   good_cgs, bad_seen (every bad code-group since reset), k, d (the last decode)
// A code-group is bad when it is invalid, or when it holds a comma and is odd-numbered (36.2.5.1.3).
// Bench choices: in LOSS_OF_SYNC the decoder takes its running disparity from the comma it finds; an invalid
// code-group leaves the decoder's running disparity as the received bits set it.
module eth_1000x_sync;
  hs_8b10b c8();
  int state = 0, good_cgs = 0, bad_seen = 0;
  bit even = 0, sync = 0, rd = 0, k = 0; bit [7:0] d = 0;
  function automatic void reset(); state = 0; good_cgs = 0; bad_seen = 0; even = 0; sync = 0; rd = 0; endfunction
  function automatic bit rx(input [9:0] code);
    reg [11:0] r; bit invalid, comma, is_d, bad;
    comma = code[9:3] == 7'b0011111 || code[9:3] == 7'b1100000;
    if (state == 0 && comma) rd = (code[9:3] == 7'b1100000);
    r = c8.decode(code, rd);                           // {rd_out, disp_err, code_err, k, d}
    rd = r[11]; k = r[8]; d = r[7:0];
    invalid = r[10] || r[9];
    is_d = !invalid && !r[8];
    bad = invalid || (comma && even);                  // even: the one before was even, so this one is odd
    if (bad && state != 0) bad_seen++;
    case (state)
      0: begin if (comma) begin state = 1; even = 1; end else even = !even; end
      1, 3, 5: begin even = 0; state = is_d ? state + 1 : 0; end
      2, 4: begin
        if (bad) state = 0;
        else if (comma) begin state = state + 1; even = 1; end
        else even = !even;
      end
      6: begin even = !even; if (bad) begin state = 7; good_cgs = 0; end end
      7, 9, 11: begin
        even = !even;
        if (bad) begin state = (state == 11) ? 0 : state + 2; good_cgs = 0; end
        else begin state = state + 1; good_cgs = 1; end
      end
      default: begin                                   // 8, 10, 12: counting good code-groups
        even = !even;
        if (bad) begin state = (state == 12) ? 0 : state + 1; good_cgs = 0; end
        else if (good_cgs == 3) begin state = (state == 8) ? 6 : state - 3; good_cgs = 0; end
        else good_cgs++;
      end
    endcase
    sync = state >= 6;
    return sync;
  endfunction
endmodule

// ---- 10GBASE-R and 25GBASE-R: 64B/66B blocks (Clause 49; Clause 107 uses the same code) ----
// Eight XGMII characters are one vector raw[71:0] (49.2.13.2.2): raw[k] is the control flag of character k,
// raw[8 + 8*k +: 8] its octet. A block is blk[65:0]; bit 0 is sent first. blk[1:0] is the sync header,
// blk[9:2] the block type field of a control block, the rest the payload (Figure 49-7).

// eth_66: the control blocks that hold no Start, no Terminate and no frame data.
//   c_code(x)       Table 49-1: the 7-bit C code of XGMII control code x; 7Fh if x is not in the table
//   enc_ctrl(raw)   {ok, blk}: block type 1Eh (eight control characters), 2Dh (four, then an ordered set),
//                   4Bh (an ordered set, then four) or 55h (two ordered sets); ok = 0 if raw is none of these.
//                   It only lays out the fields. Whether the vector may be sent is the transmit process's
//                   decision (eth_66_tx).
//   on_wire(blk)    the 66 bits as text in the order they are sent: sync, block type, payload
//   ham(a, b)       how many bits differ between two block type values
// Fault: wrong_block_type (types 2Dh and 4Bh are swapped).
module eth_66;
  bit wrong_block_type = 0;
  function automatic [6:0] c_code(input [7:0] x);
    case (x)
      8'h07: return 7'h00;                             // idle
      8'h06: return 7'h06;                             // low power idle
      8'hfe: return 7'h1e;                             // error
      8'h1c: return 7'h2d;                             // the six reserved characters
      8'h3c: return 7'h33;
      8'h7c: return 7'h4b;
      8'hbc: return 7'h55;
      8'hdc: return 7'h66;
      8'hf7: return 7'h78;
      default: return 7'h7f;
    endcase
  endfunction
  function automatic [7:0] ch(input [71:0] raw, input int k); return raw[8 + 8*k +: 8]; endfunction
  // characters k to k+3 are a sequence ordered set: 9Ch with its flag, then three data octets
  function automatic bit is_q(input [71:0] raw, input int k);
    return raw[k] && ch(raw, k) == 8'h9c && !raw[k + 1] && !raw[k + 2] && !raw[k + 3];
  endfunction
  // characters k to k+3 are control characters with a C code
  function automatic bit is_c4(input [71:0] raw, input int k);
    for (int j = k; j < k + 4; j++) if (!raw[j] || c_code(ch(raw, j)) == 7'h7f) return 0;
    return 1;
  endfunction
  function automatic [66:0] enc_ctrl(input [71:0] raw);
    reg [65:0] b; bit q0, q4, c0, c4;
    b = 66'd0;
    b[1:0] = 2'b01;                                    // sync header "10": bit 0, sent first, is 1
    q0 = is_q(raw, 0); q4 = is_q(raw, 4); c0 = is_c4(raw, 0); c4 = is_c4(raw, 4);
    if (c0 && c4) b[9:2] = 8'h1e;
    else if (c0 && q4) b[9:2] = wrong_block_type ? 8'h4b : 8'h2d;
    else if (q0 && c4) b[9:2] = wrong_block_type ? 8'h2d : 8'h4b;
    else if (q0 && q4) b[9:2] = 8'h55;
    else return 67'd0;
    if (c0) for (int k = 0; k < 4; k++) b[10 + 7*k +: 7] = c_code(ch(raw, k));
    else begin b[33:10] = raw[39:16]; b[37:34] = 4'h0; end     // D1 to D3, then the O code of the sequence set
    if (c4) for (int k = 4; k < 8; k++) b[10 + 7*k +: 7] = c_code(ch(raw, k));
    else begin b[41:38] = 4'h0; b[65:42] = raw[71:48]; end     // the O code, then D5 to D7
    return {1'b1, b};
  endfunction
  function automatic string on_wire(input [65:0] blk);
    string s;
    s = "";
    for (int i = 0; i < 66; i++) begin
      if (i == 2 || i == 10) s = {s, " "};
      s = {s, blk[i] ? "1" : "0"};
    end
    return s;
  endfunction
  function automatic int ham(input [7:0] a, input [7:0] b);
    int n; reg [7:0] x;
    x = a ^ b; n = 0;
    for (int i = 0; i < 8; i++) if (x[i]) n++;
    return n;
  endfunction
endmodule

// eth_66_tx: the transmit state diagram (Figure 49-16) without the EEE state. One call per vector.
//   step(t)   t is the T_TYPE of the vector: 0 C (control), 1 S (start), 2 T (terminate), 3 D (data), 4 E (none of these).
//             Returns 1 if the vector is encoded and sent, 0 if the error block goes out in its place.
//   state     0 TX_INIT, 1 TX_C, 2 TX_D, 3 TX_T, 4 TX_E
module eth_66_tx;
  int state = 0;
  function automatic void reset(); state = 0; endfunction
  function automatic bit step(input int t);
    case (state)
      0, 1, 3: state = (t == 0) ? 1 : (t == 1) ? 2 : 4;                    // TX_INIT, TX_C, TX_T: only C or S may follow
      2: state = (t == 3) ? 2 : (t == 2) ? 3 : 4;                          // TX_D: only D or T may follow
      default: state = (t == 2) ? 3 : (t == 3) ? 2 : (t == 0) ? 1 : 4;     // TX_E: T, D or C leave it
    endcase
    return state != 4;
  endfunction
endmodule

// eth_66_comp: clock compensation on XGMII columns (49.2.4.7, 49.2.4.10). Call once per column, in order.
// A column is {c[3:0], d[31:0]}: lane k is flag c[k] and octet d[8k+7:8k].
//   can_delete(c, d)   1 if this column may be dropped: four idles that hold none of the first four characters
//                      after a Terminate, or the second of two consecutive sequence ordered sets
//   can_insert(c, d)   1 if an idle column may be added after this one: it is idle or an ordered set
module eth_66_comp;
  bit guard = 0, prev_seq = 0;
  function automatic void reset(); guard = 0; prev_seq = 0; endfunction
  function automatic bit is_seq(input [3:0] c, input [31:0] d); return c == 4'b0001 && d[7:0] == 8'h9c; endfunction
  function automatic bit is_idle(input [3:0] c, input [31:0] d); return c == 4'b1111 && d == 32'h07070707; endfunction
  function automatic bit can_delete(input [3:0] c, input [31:0] d);
    bit ok, has_t;
    has_t = 0;
    for (int k = 0; k < 4; k++) if (c[k] && d[8*k +: 8] == 8'hfd) has_t = 1;
    ok = (is_idle(c, d) && !guard) || (is_seq(c, d) && prev_seq);
    guard = has_t;                                     // the next column holds some of the four characters after /T/
    prev_seq = is_seq(c, d) && !ok;                    // only one of the two
    return ok;
  endfunction
  function automatic bit can_insert(input [3:0] c, input [31:0] d); return is_idle(c, d) || is_seq(c, d); endfunction
endmodule

// eth_66_scr: the scrambler and the descrambler of 10GBASE-R (49.2.6, 49.2.10; Figures 49-8 and 49-10).
// The register is s[57:0]: stage S0 is s[0] and holds the newest line bit. Use one instance to scramble and
// another to descramble.
//   scr_bit(b)       one payload bit in, one line bit out: b XOR S38 XOR S57. The line bit shifts into S0.
//   dscr_bit(b)      one line bit in, one payload bit out: the same XOR. The received bit shifts into S0.
//   scramble(blk)    a whole block: bits 1:0 (the sync header) pass, bits 2 to 65 are scrambled in that order
//   descramble(blk)  the reverse
//   load(v)          sets the register (the standard asks for no start value)
// Fault: scrambles_header (the two sync header bits go through the scrambler too).
module eth_66_scr;
  bit [57:0] s = 58'd0;
  bit scrambles_header = 0;
  function automatic void load(input [57:0] v); s = v; endfunction
  function automatic bit scr_bit(input bit b);
    bit o; o = b ^ s[38] ^ s[57]; s = {s[56:0], o}; return o;
  endfunction
  function automatic bit dscr_bit(input bit b);
    bit o; o = b ^ s[38] ^ s[57]; s = {s[56:0], b}; return o;
  endfunction
  function automatic [65:0] scramble(input [65:0] blk);
    reg [65:0] o; o = blk;
    for (int i = scrambles_header ? 0 : 2; i < 66; i++) o[i] = scr_bit(blk[i]);
    return o;
  endfunction
  function automatic [65:0] descramble(input [65:0] blk);
    reg [65:0] o; o = blk;
    for (int i = 2; i < 66; i++) o[i] = dscr_bit(blk[i]);
    return o;
  endfunction
endmodule

// eth_prbs31: the PRBS31 pattern generator (49.2.8, Figure 49-9). The register is s[30:0], stage S0 is s[0].
//   gen_bit()   the next pattern bit: S27 XOR S30 shifts into S0, and the output is that bit inverted
// The register must not be all zeros: it would stay there. The checker is not in this file.
module eth_prbs31;
  bit [30:0] s = 31'h7fffffff;
  function automatic bit gen_bit();
    bit f; f = s[27] ^ s[30]; s = {s[29:0], f}; return !f;
  endfunction
endmodule

// eth_66_test: the square wave of 49.2.8 and the two data patterns of the pseudo-random test pattern.
//   sq_bit()        square wave: sq_n ones, then sq_n zeros (sq_n may be 4 to 11)
//   pattern()       the 64-bit data pattern: zeros, or the payload of a block with two local fault sets (lf_pattern)
// The pseudo-random pattern generator and its checker (49.2.8, 49.2.12) are not in this file.
module eth_66_test;
  eth_66 code();
  bit lf_pattern = 0;
  int sq_n = 8, sq_k = 0;
  function automatic void restart(); sq_k = 0; endfunction
  function automatic bit sq_bit();
    bit b; b = (sq_k < sq_n); sq_k = (sq_k + 1) % (2 * sq_n); return b;
  endfunction
  function automatic [63:0] pattern();
    reg [66:0] r;
    if (!lf_pattern) return 64'd0;
    r = code.enc_ctrl({64'h0100009c_0100009c, 8'h11}); return r[65:2];
  endfunction
endmodule

// eth_66_loop: PCS loopback (49.2.14.4), switched by MDIO bit 3.0.14.
//   rx_block(from_tx, from_pma)   what the receive path decodes: its own transmit block when loopback is 1
//   pma_word(w)                   what goes to the PMA: the word 00FFh when loopback is 1, else w
module eth_66_loop;
  bit loopback = 0;
  function automatic [65:0] rx_block(input [65:0] from_tx, input [65:0] from_pma); return loopback ? from_tx : from_pma; endfunction
  function automatic [15:0] pma_word(input [15:0] w); return loopback ? 16'h00ff : w; endfunction
endmodule
Read included file: hs_blk.sv
`timescale 1ns/1ns
// hs_blk.sv: block codes (read-only). A block is a sync header and a payload. Headers are written as
// they go on the wire, most significant bit first ("01" sends 0, then 1). The payload is sent bit 0
// first and is scrambled with a self-synchronising x^58 + x^39 + 1 scrambler (the header never is).
// Every layout uses that 64b/66b-style scrambler. USB 3.2 Gen 2 (§6.3.2.3) and USB4 (§4.3.1.5) use an
// additive x^23 LFSR kept in step by ordered sets instead; that is not modelled here (hs_scr has the
// polynomial as use_x23_usb3() for a scrambler on its own). Set scramble = 0 / descramble = 0 for none.
//   use_66()        64b/66b: data 01, control 10 (USB4 v2.0 Figure 4-22/4-23)
//   use_132_usb4()  128b/132b: data 0101, ordered set 1010 (USB4 v2.0 Figure 4-22/4-23)
//   use_132_usb3()  128b/132b: data 0011b, control 1100b, bit 0 first (USB 3.2 §6.3.2.2, Figure 6-11),
//                   so on the wire data is 1100 and control is 0011
//   use_130()       128b/130b with the 64b/66b header values: a bench layout (PCIe's own values are unverified)
// hs_blk (transmitter): blk_tx(payload, ctrl) -> the block in the low n bits, bit n-1 sent first.
// hs_blk_lock (receiver): push(b) one line bit at a time; returns 1 when a block with a valid header is
//   complete and locked (then hdr, ctrl and payload hold it). A locked block with an invalid header is not
//   delivered: push returns 0, hdr_ok is 0 and hdr_errs counts it. USB 3.2's single-bit header correction
//   (§6.3.2.2) is not modelled. Lock after lock_good valid headers in a row; an invalid header
//   before lock slips the boundary by one bit; once locked, bad_limit invalid headers within a window of
//   bad_window blocks lose lock. The default counts (64, 64, 16) are those of IEEE 802.3 Figure 49-14 (read 2026-11-14).
// hs_gearbox: a bit FIFO between a block width and a word width: gb_push(v, n), gb_pop(n), gb_level().
// Faults: header_00 (hs_blk sends 00 on every block), lock_on_first and never_unlock (hs_blk_lock).
module hs_blk;
  int hdr_bits = 2, pay_bits = 64; bit [3:0] hdr_data = 4'b0001, hdr_ctrl = 4'b0010;
  bit scramble = 1, header_00 = 0, trace = 0; int blocks = 0;
  hs_scr scr(); bit ready = 0;
  // set up on first use (an initial block here could run after the bench's first call)
  function automatic void prep(); if (!ready) begin scr.use_x58(); scr.s = 64'h3ff_ffff_ffff_ffff; ready = 1; end endfunction
  function automatic void set(input int h, input int p, input [3:0] d, input [3:0] c); hdr_bits = h; pay_bits = p; hdr_data = d; hdr_ctrl = c; endfunction
  function automatic void use_66(); set(2, 64, 4'b0001, 4'b0010); endfunction
  function automatic void use_130(); set(2, 128, 4'b0001, 4'b0010); endfunction
  function automatic void use_132_usb4(); set(4, 128, 4'b0101, 4'b1010); endfunction
  function automatic void use_132_usb3(); set(4, 128, 4'b1100, 4'b0011); endfunction
  function automatic int n(); return hdr_bits + pay_bits; endfunction
  function automatic [131:0] blk_tx(input [127:0] payload, input bit ctrl);
    reg [131:0] v; reg [3:0] h; int m; prep(); m = n(); v = 132'd0;
    h = header_00 ? 4'd0 : ctrl ? hdr_ctrl : hdr_data;
    for (int i = 0; i < hdr_bits; i++) v[m - 1 - i] = h[hdr_bits - 1 - i];
    for (int i = 0; i < pay_bits; i++) v[m - 1 - hdr_bits - i] = scramble ? scr.scr_bit(payload[i]) : payload[i];
    if (trace) $display("b%0d TX %s", blocks, ctrl ? "ctrl" : "data");
    blocks++;
    return v;
  endfunction
endmodule

module hs_blk_lock;
  int hdr_bits = 2, pay_bits = 64; bit [3:0] hdr_data = 4'b0001, hdr_ctrl = 4'b0010;
  int lock_good = 64, bad_window = 64, bad_limit = 16;
  bit descramble = 1, lock_on_first = 0, never_unlock = 0, trace = 0;
  bit locked = 0; int nbits = 0, pos = 0, slips = 0, good_run = 0, hdr_errs = 0, blocks = 0, lock_at = -1, unlocks = 0, win_n = 0, win_bad = 0;
  bit [131:0] sh = 132'd0; bit [3:0] hdr; bit ctrl; bit hdr_ok = 0; bit [127:0] payload;
  hs_scr dscr(); bit ready = 0;
  function automatic void set(input int h, input int p, input [3:0] d, input [3:0] c); hdr_bits = h; pay_bits = p; hdr_data = d; hdr_ctrl = c; endfunction
  function automatic void use_66(); set(2, 64, 4'b0001, 4'b0010); endfunction
  function automatic void use_130(); set(2, 128, 4'b0001, 4'b0010); endfunction
  function automatic void use_132_usb4(); set(4, 128, 4'b0101, 4'b1010); endfunction
  function automatic void use_132_usb3(); set(4, 128, 4'b1100, 4'b0011); endfunction
  function automatic void restart(); locked = 0; nbits = 0; pos = 0; slips = 0; good_run = 0; hdr_errs = 0; blocks = 0; lock_at = -1; unlocks = 0; win_n = 0; win_bad = 0; endfunction
  function automatic bit push(input bit b);
    int m; reg ok; m = hdr_bits + pay_bits;
    if (!ready) begin dscr.use_x58(); ready = 1; end
    sh = {sh[130:0], b}; nbits++; pos++;
    if (pos < m) return 0;
    pos = 0; hdr = 4'd0;
    for (int i = 0; i < hdr_bits; i++) hdr[hdr_bits - 1 - i] = sh[m - 1 - i];
    ok = (hdr == hdr_data) || (hdr == hdr_ctrl); ctrl = (hdr == hdr_ctrl); hdr_ok = ok;
    blocks++;
    if (!ok) hdr_errs++;
    if (!locked) begin
      if (ok) begin
        good_run++;
        if (good_run >= (lock_on_first ? 1 : lock_good)) begin
          locked = 1; win_n = 0; win_bad = 0; if (lock_at < 0) lock_at = nbits;
          if (trace) $display("b%0d LOCK bit=%0d slips=%0d", blocks, nbits, slips);
        end
      end else begin good_run = 0; pos = -1; slips++; end
      return 0;
    end
    win_n++; if (!ok) win_bad++;
    if (win_bad >= bad_limit && !never_unlock) begin
      locked = 0; good_run = 0; unlocks++; pos = -1; slips++;
      if (trace) $display("b%0d UNLOCK bit=%0d", blocks, nbits);
      return 0;
    end
    if (win_n >= bad_window) begin win_n = 0; win_bad = 0; end
    // the descrambler still takes the payload bits of a bad block, so it stays in step
    for (int i = 0; i < pay_bits; i++) payload[i] = descramble ? dscr.dscr_bit(sh[m - 1 - hdr_bits - i]) : sh[m - 1 - hdr_bits - i];
    return ok;
  endfunction
endmodule

module hs_gearbox;
  bit q [0:1023]; int head = 0, count = 0, overflows = 0;
  function automatic void gb_push(input [131:0] v, input int n);   // bit n-1 first
    for (int i = n - 1; i >= 0; i--) begin
      if (count == 1024) overflows++; else begin q[(head + count) % 1024] = v[i]; count++; end
    end
  endfunction
  function automatic int gb_level(); return count; endfunction
  function automatic [131:0] gb_pop(input int n);                    // the oldest bit lands in bit n-1
    reg [131:0] w; w = 132'd0;
    for (int i = n - 1; i >= 0 && count > 0; i--) begin w[i] = q[head]; head = (head + 1) % 1024; count--; end
    return w;
  endfunction
endmodule

Check Yourself

Predict the outputThe program flips two line bits, 39 bits apart, and counts the wrong bits after the descrambler. What does it print?
`timescale 1ns/1ns
module tb;
  eth_66 code(); eth_66_scr tx(); eth_66_scr rx(); reg [65:0] idle, b0, b1, b2, d0, d1, d2; int wrong;
  function automatic int ones(input [65:0] v);
    int k; k = 0; for (int i = 0; i < 66; i++) k += v[i]; return k;
  endfunction
  initial begin
    idle = code.enc_ctrl({64'h0707070707070707, 8'hff});
    b0 = tx.scramble(idle); b1 = tx.scramble(idle); b2 = tx.scramble(idle);
    b0[10] = !b0[10];                   // two line bits flipped,
    b0[49] = !b0[49];                   // 39 bits apart
    d0 = rx.descramble(b0); d1 = rx.descramble(b1); d2 = rx.descramble(b2);
    wrong = ones(d0 ^ idle) + ones(d1 ^ idle) + ones(d2 ^ idle);
    $display("wrong bits after the descrambler: %0d", wrong);
    $finish;
  end
endmodule
Read included file: hs_pkg.sv
`timescale 1ns/1ns
// hs_pkg.sv: shared pure functions, and the bench random generator (read-only).
package hs_pkg;
  // xorshift32 (Marsaglia 2003): a linear generator over GF(2), period 2^32 - 1. A zero state is
  // replaced by 1, because zero maps to itself.
  function automatic [31:0] xs32(input [31:0] s);
    reg [31:0] x;
    x = (s == 32'd0) ? 32'd1 : s;
    x = x ^ (x << 13); x = x ^ (x >> 17); x = x ^ (x << 5);
    return x;
  endfunction
  // A Fibonacci PRBS generator x^n + x^m + 1 (PRBS7: 7,6; PRBS9: 9,5; PRBS15: 15,14; PRBS23: 23,18;
  // PRBS31: 31,28). The output bit is s[n-1]; the next state shifts the feedback into bit 0.
  function automatic [31:0] prbs_next(input [31:0] s, input int n, input int m);
    reg fb;
    fb = s[n-1] ^ s[m-1];
    return ((s << 1) | {31'd0, fb}) & ((n == 32) ? 32'hffffffff : ((32'd1 << n) - 32'd1));
  endfunction
  function automatic int ones(input [63:0] v);
    int n; n = 0;
    for (int i = 0; i < 64; i++) n += v[i];
    return n;
  endfunction
  // GF(16) with x^4 + x + 1, and GF(1024) with x^10 + x^3 + 1: shift-and-add multiply, no tables.
  function automatic [3:0] gf16_mul(input [3:0] a, input [3:0] b);
    reg [3:0] p, x; p = 4'd0; x = a;
    for (int i = 0; i < 4; i++) begin
      if (b[i]) p = p ^ x;
      x = x[3] ? ({x[2:0], 1'b0} ^ 4'b0011) : {x[2:0], 1'b0};
    end
    return p;
  endfunction
  function automatic [3:0] gf16_pow(input int e);   // alpha^e, alpha = x
    reg [3:0] p; int k; p = 4'd1; k = e % 15; if (k < 0) k += 15;
    for (int i = 0; i < k; i++) p = gf16_mul(p, 4'd2);
    return p;
  endfunction
  function automatic int gf16_log(input [3:0] a);   // -1 for 0
    reg [3:0] p; p = 4'd1;
    if (a == 4'd0) return -1;
    for (int i = 0; i < 15; i++) begin if (p == a) return i; p = gf16_mul(p, 4'd2); end
    return -1;
  endfunction
  function automatic [9:0] gf1024_mul(input [9:0] a, input [9:0] b);
    reg [9:0] p, x; p = 10'd0; x = a;
    for (int i = 0; i < 10; i++) begin
      if (b[i]) p = p ^ x;
      x = x[9] ? ({x[8:0], 1'b0} ^ 10'b0000001001) : {x[8:0], 1'b0};
    end
    return p;
  endfunction
  function automatic [9:0] gf1024_pow(input int e);
    reg [9:0] p; int k; p = 10'd1; k = e % 1023; if (k < 0) k += 1023;
    for (int i = 0; i < k; i++) p = gf1024_mul(p, 10'd2);
    return p;
  endfunction
endpackage

// hs_rng: the bench's random numbers. Same seed, same numbers, on every engine.
module hs_rng;
  int unsigned s = 32'h2545f491;
  function automatic void seed(input int unsigned v); s = (v == 0) ? 32'd1 : v; endfunction
  function automatic int unsigned next(); s = hs_pkg::xs32(s); return s; endfunction
  function automatic int below(input int n); s = hs_pkg::xs32(s); return (n <= 0) ? 0 : int'(s % n); endfunction
  function automatic bit bit1(); s = hs_pkg::xs32(s); return s[16]; endfunction
  function automatic bit chance_ppm(input int ppm); s = hs_pkg::xs32(s); return (s % 1000000) < ppm; endfunction
  function automatic [7:0] byte8(); s = hs_pkg::xs32(s); return s[23:16]; endfunction
endmodule
Read included file: hs_code.sv
`timescale 1ns/1ns
// hs_code.sv: line codes, CRCs and scramblers (read-only).

// ---------------------------------------------------------------------------------------------
// hs_8b10b: 8b/10b encoder and decoder with running disparity and the 12 K codes.
// code[9:0] = {a,b,c,d,e,i,f,g,h,j}; bit a (code[9]) goes on the wire first. rd: 0 = RD-, 1 = RD+.
//   encode(d, k, rd_in) -> {rd_out, code[9:0]}            (11 bits)
//   decode(code, rd_in) -> {rd_out, disp_err, code_err, k, d[7:0]}   (12 bits)
//   enc(d, k) / dec(code): the same, with the running disparity kept in rd_tx / rd_rx
// A K request for a byte that is not one of the 12 K codes is encoded as data and counted in bad_k.
// Decoder: code_err = the code is in neither column of the table; disp_err = it is a valid code
// only in the other column. rd_out follows the sub-block rule on the received bits.
// Faults: no_rd (always the RD- column), a7_never (never the alternate D.x.A7),
//         keep_rd_on_unbalanced (the 4b sub-block is chosen with the disparity from before the 6b one),
//         no_balanced_flip (D.07 and D.x.3 keep their RD- form at RD+), dec_no_disp_check.
module hs_8b10b;
  bit no_rd = 0, a7_never = 0, keep_rd_on_unbalanced = 0, no_balanced_flip = 0, dec_no_disp_check = 0;
  bit trace = 0;
  bit rd_tx = 0, rd_rx = 0;
  int bad_k = 0, symbols = 0, code_errs = 0, disp_errs = 0;
  bit last_k = 0, last_code_err = 0, last_disp_err = 0;
  bit valid_m [0:1023]; bit valid_p [0:1023]; bit [8:0] kd [0:1023]; bit built = 0;
  function automatic [5:0] t6(input [4:0] x);   // 5b/6b, RD- column, abcdei
    case (x)
      5'd0: return 6'b100111;  5'd1: return 6'b011101;  5'd2: return 6'b101101;  5'd3: return 6'b110001;
      5'd4: return 6'b110101;  5'd5: return 6'b101001;  5'd6: return 6'b011001;  5'd7: return 6'b111000;
      5'd8: return 6'b111001;  5'd9: return 6'b100101;  5'd10: return 6'b010101; 5'd11: return 6'b110100;
      5'd12: return 6'b001101; 5'd13: return 6'b101100; 5'd14: return 6'b011100; 5'd15: return 6'b010111;
      5'd16: return 6'b011011; 5'd17: return 6'b100011; 5'd18: return 6'b010011; 5'd19: return 6'b110010;
      5'd20: return 6'b001011; 5'd21: return 6'b101010; 5'd22: return 6'b011010; 5'd23: return 6'b111010;
      5'd24: return 6'b110011; 5'd25: return 6'b100110; 5'd26: return 6'b010110; 5'd27: return 6'b110110;
      5'd28: return 6'b001110; 5'd29: return 6'b101110; 5'd30: return 6'b011110; default: return 6'b101011;
    endcase
  endfunction
  function automatic [3:0] t4d(input [2:0] y);  // 3b/4b data, RD- column, fghj (y = 7 is P7)
    case (y)
      3'd0: return 4'b1011; 3'd1: return 4'b1001; 3'd2: return 4'b0101; 3'd3: return 4'b1100;
      3'd4: return 4'b1101; 3'd5: return 4'b1010; 3'd6: return 4'b0110; default: return 4'b1110;
    endcase
  endfunction
  function automatic [3:0] t4k(input [2:0] y);  // 3b/4b for K codes, RD- form before the flip
    case (y)
      3'd0: return 4'b1011; 3'd1: return 4'b0110; 3'd2: return 4'b1010; 3'd3: return 4'b1100;
      3'd4: return 4'b1101; 3'd5: return 4'b0101; 3'd6: return 4'b1001; default: return 4'b0111;
    endcase
  endfunction
  function automatic bit k_ok(input [7:0] d);
    return d[4:0] == 5'd28 || d == 8'hf7 || d == 8'hfb || d == 8'hfd || d == 8'hfe;
  endfunction
  function automatic int n6(input [5:0] v); return v[0] + v[1] + v[2] + v[3] + v[4] + v[5]; endfunction
  function automatic int n4(input [3:0] v); return v[0] + v[1] + v[2] + v[3]; endfunction
  // running disparity at the end of a sub-block (more ones: +; more zeros: -; 000111 and 0011: +; 111000 and 1100: -)
  function automatic bit rd6(input [5:0] v, input bit rd);
    return (n6(v) > 3) ? 1'b1 : (n6(v) < 3) ? 1'b0 : (v == 6'b000111) ? 1'b1 : (v == 6'b111000) ? 1'b0 : rd;
  endfunction
  function automatic bit rd4(input [3:0] v, input bit rd);
    return (n4(v) > 2) ? 1'b1 : (n4(v) < 2) ? 1'b0 : (v == 4'b0011) ? 1'b1 : (v == 4'b1100) ? 1'b0 : rd;
  endfunction
  // faults: [0] no_rd [1] a7_never [2] keep_rd_on_unbalanced [3] no_balanced_flip
  function automatic [10:0] core(input [7:0] d, input bit k, input bit rd_in, input [3:0] f);
    reg [5:0] six; reg [3:0] four; reg rd0, r6, rd1, a7, kk; reg [4:0] x; reg [2:0] y; int o6, o4;
    x = d[4:0]; y = d[7:5]; kk = k && k_ok(d); rd0 = f[0] ? 1'b0 : rd_in;
    six = (kk && x == 5'd28) ? 6'b001111 : t6(x); o6 = n6(six);
    if (rd0 && (o6 != 3 || (six == 6'b111000 && !f[3]))) begin six = ~six; o6 = 6 - o6; end
    r6 = (o6 > 3) ? 1'b1 : (o6 < 3) ? 1'b0 : (six == 6'b000111) ? 1'b1 : (six == 6'b111000) ? 1'b0 : rd0;
    rd1 = f[2] ? rd0 : r6;
    if (kk) begin
      four = t4k(y); if (rd1) four = ~four;
    end else begin
      a7 = (y == 3'd7) && !f[1] && ((!rd1 && (x == 5'd17 || x == 5'd18 || x == 5'd20)) || (rd1 && (x == 5'd11 || x == 5'd13 || x == 5'd14)));
      four = a7 ? 4'b0111 : t4d(y);
      if (rd1 && (n4(four) != 2 || (four == 4'b1100 && !f[3]))) four = ~four;
    end
    o4 = n4(four);
    return {(o4 > 2) ? 1'b1 : (o4 < 2) ? 1'b0 : (four == 4'b0011) ? 1'b1 : (four == 4'b1100) ? 1'b0 : r6, six, four};
  endfunction
  function automatic [10:0] encode(input [7:0] d, input bit k, input bit rd_in);
    if (k && !k_ok(d)) bad_k++;
    return core(d, k, rd_in, {no_balanced_flip, keep_rd_on_unbalanced, a7_never, no_rd});
  endfunction
  function automatic void build();
    reg [10:0] c;
    for (int i = 0; i < 1024; i++) begin valid_m[i] = 0; valid_p[i] = 0; kd[i] = 9'd0; end
    for (int i = 0; i < 268; i++) begin
      reg [7:0] d; reg k;
      if (i < 256) begin d = i[7:0]; k = 0; end
      else begin k = 1; d = (i < 264) ? {3'(i - 256), 5'd28} : (i == 264) ? 8'hf7 : (i == 265) ? 8'hfb : (i == 266) ? 8'hfd : 8'hfe; end
      c = core(d, k, 1'b0, 4'd0); valid_m[c[9:0]] = 1; kd[c[9:0]] = {k, d};
      c = core(d, k, 1'b1, 4'd0); valid_p[c[9:0]] = 1; kd[c[9:0]] = {k, d};
    end
    built = 1;
  endfunction
  function automatic [11:0] decode(input [9:0] code, input bit rd_in);
    reg here, there, ce, de, r;
    if (!built) build();
    here = rd_in ? valid_p[code] : valid_m[code];
    there = rd_in ? valid_m[code] : valid_p[code];
    ce = !(here || there); de = !ce && !here && !dec_no_disp_check;
    r = rd4(code[3:0], rd6(code[9:4], rd_in));
    return {r, de, ce, ce ? 9'd0 : kd[code]};
  endfunction
  function automatic [9:0] enc(input [7:0] d, input bit k);
    reg [10:0] r; r = encode(d, k, rd_tx); rd_tx = r[10];
    if (trace) $display("s%0d TX %s%0d.%0d code=%b rd=%s", symbols, (k && k_ok(d)) ? "K" : "D", d[4:0], d[7:5], r[9:0], r[10] ? "+" : "-");
    symbols++;
    return r[9:0];
  endfunction
  function automatic [8:0] dec(input [9:0] code);
    reg [11:0] r; r = decode(code, rd_rx); rd_rx = r[11];
    last_disp_err = r[10]; last_code_err = r[9]; last_k = r[8];
    if (r[9]) code_errs++; if (r[10]) disp_errs++;
    if (trace && (r[9] || r[10])) $display("RX %b %s", code, r[9] ? "code error" : "disparity error");
    return r[8:0];
  endfunction
  function automatic bit comma7(input [6:0] w); return w == 7'b0011111 || w == 7'b1100000; endfunction
endmodule

// ---------------------------------------------------------------------------------------------
// hs_crc: a CRC of 1 to 32 bits with any polynomial, seed, bit order and final inversion.
// The register shifts left; the polynomial omits the x^width term. The field is sent register bit
// width-1 first (USB 2.0, USB 3.2 and Ethernet all send it this way).
//   use_crc32(), use_crc16_usb2(), use_crc5_usb2(), use_crc16_usb3(): parameter sets
//   reset(), crc_bit(b), crc_byte(v), crc_bits(v, n), field(), field_bit(i), check_value(), crc_residue_ok()
// Faults: msb_first (bytes enter MSB first), no_invert (the field is not complemented), seed_zero.
module hs_crc;
  int width = 32;
  bit [31:0] poly = 32'h04c11db7, seed = 32'hffffffff, residue = 32'hc704dd7b;
  bit lsb_first = 1, invert = 1;
  bit msb_first = 0, no_invert = 0, seed_zero = 0;
  bit [31:0] r = 32'hffffffff;
  function automatic [31:0] mask(); return (width >= 32) ? 32'hffffffff : ((32'd1 << width) - 32'd1); endfunction
  function automatic void reset(); r = seed_zero ? 32'd0 : (seed & mask()); endfunction
  function automatic void set(input int w, input [31:0] p, input [31:0] s, input [31:0] res, input bit lsb, input bit inv);
    width = w; poly = p; seed = s; residue = res; lsb_first = lsb; invert = inv; reset();
  endfunction
  function automatic void use_crc32();      set(32, 32'h04c11db7, 32'hffffffff, 32'hc704dd7b, 1, 1); endfunction
  function automatic void use_crc16_usb2(); set(16, 32'h8005, 32'hffff, 32'h800d, 1, 1); endfunction
  function automatic void use_crc5_usb2();  set(5, 32'h05, 32'h1f, 32'h0c, 1, 1); endfunction
  function automatic void use_crc16_usb3(); set(16, 32'h100b, 32'hffff, 32'hf6aa, 1, 1); endfunction
  function automatic void crc_bit(input bit b);
    reg fb; fb = b ^ r[width - 1];
    r = ((r << 1) ^ (fb ? poly : 32'd0)) & mask();
  endfunction
  function automatic void crc_byte(input [7:0] v);
    for (int i = 0; i < 8; i++) crc_bit(v[(lsb_first ^ msb_first) ? i : 7 - i]);
  endfunction
  function automatic void crc_bits(input [31:0] v, input int n);   // n bits of v, bit 0 first
    for (int i = 0; i < n; i++) crc_bit(v[i]);
  endfunction
  function automatic [31:0] field(); return (invert && !no_invert) ? (~r & mask()) : r; endfunction
  function automatic bit field_bit(input int i); reg [31:0] f; f = field(); return f[width - 1 - i]; endfunction
  // the usual published "check" number: the field with its first-sent bit read as bit 0
  function automatic [31:0] check_value();
    reg [31:0] f, o; f = field(); o = 32'd0;
    for (int i = 0; i < width; i++) o[i] = f[width - 1 - i];
    return lsb_first ? o : f;
  endfunction
  function automatic bit crc_residue_ok(); return r == (residue & mask()); endfunction
endmodule

// ---------------------------------------------------------------------------------------------
// hs_scr: additive (frame-synchronous) and multiplicative (self-synchronising) scramblers.
// poly holds the coefficients: bit k is x^k; the +1 term is always used (taps() sets bit 0); len is the degree.
// Additive: a Galois LFSR. The key bit is s[len-1]; each step shifts left and adds the low terms of
//   the polynomial when the key bit is 1. The data never enters the register.
// Multiplicative: the line bit is the data bit XOR the register bits at the polynomial's terms;
//   the scrambler shifts its own output in, the descrambler shifts the received line bit in.
//   scr_add(len, poly, seed), scr_mul(len, poly), use_usb3_gen1(), use_x58(), use_x23_usb3() (see its note)
//   scr_bit(b), dscr_bit(b), scr_byte(v), dscr_byte(v) (bit 0 first), scr_reset(), scr_hold() (a skip
//   symbol: no step), scr_unscrambled() (a symbol sent in the clear: 8 steps, data untouched)
// Faults: advance_on_skip (scr_hold steps the LFSR 8 times), no_reset (scr_reset does nothing),
//         wrong_tap (the lowest term x^k becomes x^(k+1)), seed_zero (scr_reset loads 0).
module hs_scr;
  bit mult = 0; int len = 16;
  bit [63:0] poly = 64'h10039, seed = 64'hffff;
  bit advance_on_skip = 0, no_reset = 0, wrong_tap = 0, seed_zero = 0;
  bit [63:0] s = 64'hffff;
  int steps = 0;
  function automatic [63:0] lmask(); return (len >= 64) ? 64'hffffffffffffffff : ((64'd1 << len) - 64'd1); endfunction
  function automatic [63:0] taps();
    reg [63:0] p; int k; p = poly | 64'd1; k = 1;
    if (wrong_tap) begin
      while (k < len && !p[k]) k++;
      if (k < len) begin p[k] = 1'b0; p[k + 1] = 1'b1; end
    end
    return p;
  endfunction
  function automatic void load(); s = (seed_zero ? 64'd0 : seed) & lmask(); endfunction
  function automatic void scr_add(input int n, input [63:0] p, input [63:0] sd); mult = 0; len = n; poly = p; seed = sd; s = sd & lmask(); endfunction
  function automatic void scr_mul(input int n, input [63:0] p); mult = 1; len = n; poly = p; seed = 64'd0; s = 64'd0; endfunction
  function automatic void use_usb3_gen1(); scr_add(16, 64'h10039, 64'hffff); endfunction   // x^16 + x^5 + x^4 + x^3 + 1, seed FFFFh
  function automatic void use_x58(); scr_mul(58, (64'd1 << 58) | (64'd1 << 39) | 64'd1); endfunction   // x^58 + x^39 + 1
  // USB 3.2 Gen 2 (§6.3.2.3) polynomial x^23 + x^21 + x^16 + x^8 + x^5 + x^2 + 1 with seed 1DBFBCh. Only the
  // polynomial and seed are the specification's: the register form here is this library's Galois form, and
  // the reset and bypass rules of §6.3.2.3 are not modelled, so do not quote its key stream as USB's.
  function automatic void use_x23_usb3(); scr_add(23, (64'd1 << 23) | (64'd1 << 21) | (64'd1 << 16) | (64'd1 << 8) | (64'd1 << 5) | (64'd1 << 2) | 64'd1, 64'h1dbfbc); endfunction
  function automatic void scr_reset(); if (!no_reset) load(); endfunction
  function automatic bit key(); return s[len - 1]; endfunction
  function automatic void step();
    reg kb; kb = s[len - 1];
    s = ((s << 1) & lmask()) ^ (kb ? (taps() & lmask()) : 64'd0);
    steps++;
  endfunction
  // the XOR of the register bits at the polynomial's terms x^1..x^len (bit k-1 of the register for x^k)
  function automatic bit fbx(input [63:0] st); return ^(st & (taps() >> 1) & lmask()); endfunction
  function automatic bit scr_bit(input bit b);
    reg o;
    if (!mult) begin o = b ^ s[len - 1]; step(); end
    else begin o = b ^ fbx(s); s = ((s << 1) | {63'd0, o}) & lmask(); steps++; end
    return o;
  endfunction
  function automatic bit dscr_bit(input bit b);
    reg o;
    if (!mult) begin o = b ^ s[len - 1]; step(); end
    else begin o = b ^ fbx(s); s = ((s << 1) | {63'd0, b}) & lmask(); steps++; end
    return o;
  endfunction
  function automatic [7:0] scr_byte(input [7:0] v);
    reg [7:0] o; for (int i = 0; i < 8; i++) o[i] = scr_bit(v[i]); return o;
  endfunction
  function automatic [7:0] dscr_byte(input [7:0] v);
    reg [7:0] o; for (int i = 0; i < 8; i++) o[i] = dscr_bit(v[i]); return o;
  endfunction
  // a skip symbol passes unscrambled and the LFSR holds
  function automatic void scr_hold(); if (advance_on_skip && !mult) for (int i = 0; i < 8; i++) step(); endfunction
  // another symbol that is sent unscrambled (a K code other than COM and SKP): the LFSR still steps 8 times
  function automatic void scr_unscrambled(); if (!mult) for (int i = 0; i < 8; i++) step(); endfunction
endmodule
Read included file: eth_mac.sv
`timescale 1ns/1ns
// eth_frame: one MAC frame as octets, its packet as wire bits, and a bit-serial receiver.
//   pay[i]                         client data, set by the bench before build()
//   build(da, sa, lt, len)         destination, source, Length/Type, len data octets, then the FCS -> oct[0..n-1].
//                                  It adds no pad: give it 46 data octets or more. (Padding is P11.2.1's task; the
//                                  pages show the padding MAC's frames as measured tables.)
//   wire_bits(), wire_bit(i)       the packet in transmit order: preamble, SFD, frame
//   rx_start(), rx_bit(b), rx_end()  hunt for the SFD, collect octets, then parse()
//   parse()                        da, sa, lt, is_length, is_type, data_len, fcs_rx, fcs_calc, fcs_ok
// Faults: fcs_msb_first, fcs_no_invert, fcs_covers_preamble, sfd_wrong, msb_first_octets.
module eth_frame;
  localparam int MIN_FRAME = 64, MAX_BASIC = 1518, MAX_QTAG = 1522, MAX_ENVELOPE = 2000;
  bit fcs_msb_first = 0, fcs_no_invert = 0, fcs_covers_preamble = 0, sfd_wrong = 0, msb_first_octets = 0;
  hs_crc crc();
  bit [7:0] pay [0:2047];
  bit [7:0] oct [0:2047];
  int n = 0;
  bit [47:0] da = 0, sa = 0; bit [15:0] lt = 0;
  bit is_length = 0, is_type = 0, fcs_ok = 0;
  int data_len = 0;
  bit [31:0] fcs_rx = 0, fcs_calc = 0;
  // receiver state
  bit in_frame = 0; bit [7:0] hist = 0, cur = 0; int nb = 0, excess = 0, sfd_at = -1, bits_seen = 0;

  // The FCS of oct[0..len-1] as four octets: the first octet sent is in [7:0].
  function automatic [31:0] fcs_of(input int len);
    crc.use_crc32(); crc.msb_first = fcs_msb_first; crc.no_invert = fcs_no_invert; crc.reset();
    if (fcs_covers_preamble) begin
      for (int i = 0; i < 7; i++) crc.crc_byte(8'h55);
      crc.crc_byte(8'hd5);
    end
    for (int i = 0; i < len; i++) crc.crc_byte(oct[i]);
    return crc.check_value();
  endfunction

  function automatic void build(input [47:0] d, input [47:0] s, input [15:0] t, input int len);
    int k; reg [31:0] f;
    k = 0;
    for (int i = 0; i < 6; i++) begin oct[k] = d[47 - 8*i -: 8]; k++; end
    for (int i = 0; i < 6; i++) begin oct[k] = s[47 - 8*i -: 8]; k++; end
    oct[k] = t[15:8]; k++;
    oct[k] = t[7:0]; k++;
    for (int i = 0; i < len; i++) begin oct[k] = pay[i]; k++; end
    f = fcs_of(k);
    for (int i = 0; i < 4; i++) begin oct[k] = f[8*i +: 8]; k++; end
    n = k; excess = 0;
    parse();
  endfunction

  function automatic void parse();
    da = 0; sa = 0; lt = 0; is_length = 0; is_type = 0; fcs_ok = 0; data_len = 0; fcs_rx = 0; fcs_calc = 0;
    if (n >= 14) begin
      da = {oct[0], oct[1], oct[2], oct[3], oct[4], oct[5]};
      sa = {oct[6], oct[7], oct[8], oct[9], oct[10], oct[11]};
      lt = {oct[12], oct[13]};
      is_length = (lt <= 16'd1500);
      is_type = (lt >= 16'd1536);
    end
    if (n >= 18) begin
      fcs_rx = {oct[n-1], oct[n-2], oct[n-3], oct[n-4]};
      fcs_calc = fcs_of(n - 4);
      fcs_ok = (fcs_rx == fcs_calc);
      data_len = is_length ? int'(lt) : n - 18;
    end
  endfunction

  function automatic int wire_bits(); return 8 * (8 + n); endfunction
  function automatic bit wire_bit(input int i);
    int o, b; reg [7:0] v;
    o = i / 8; b = i % 8;
    if (o < 7) v = 8'h55;
    else if (o == 7) v = sfd_wrong ? 8'h55 : 8'hd5;
    else v = oct[o - 8];
    return msb_first_octets ? v[7 - b] : v[b];
  endfunction

  function automatic void rx_start();
    in_frame = 0; hist = 0; cur = 0; nb = 0; n = 0; excess = 0; sfd_at = -1; bits_seen = 0;
  endfunction
  function automatic void rx_bit(input bit b);
    bits_seen++;
    if (!in_frame) begin
      hist = {hist[6:0], b};                      // the oldest bit is hist[7]
      if (hist == 8'b10101011) begin in_frame = 1; sfd_at = bits_seen; end
    end else begin
      if (msb_first_octets) cur[7 - nb] = b; else cur[nb] = b;
      nb++;
      if (nb == 8) begin oct[n] = cur; n++; nb = 0; end
    end
  endfunction
  function automatic void rx_end(); excess = nb; parse(); endfunction
endmodule
// eth_axis: a MAC client bus in the style of AXI4-Stream (IHI 0051B 2.2 handshake, 2.5 TKEEP, 2.6 TLAST, 2.9 TUSER),
// 64 bits wide. Byte 0 of a beat is tdata[7:0] and is first in the frame (AXI4-Stream 2.4.1). Bench conventions,
// not AXI4-Stream's or 802.3's: tkeep is all ones except on the last beat, where it covers bytes 0 to k-1; one tuser
// bit (transfer-based, 2.9.1), read on the last beat only, marks a bad frame (receive) or asks the MAC to abort it
// (transmit).
//   load(n)                  beats for octets oct[0..n-1]: bd[], bk[], bl[], nbeats; bv[] = valid per cycle, ncyc
//   tx_cycles()              the transmit MAC: one beat per cycle once a frame has started. Returns 0 sent,
//                            1 underrun (tvalid fell inside the frame), 2 aborted by tuser. sent_octets, fail_cycle.
// Fault: tvalid_gap (load() leaves cycle 3 of the frame empty: the client was late with a beat).
module eth_axis;
  bit tvalid_gap = 0;
  bit [7:0] oct [0:2047];
  bit [63:0] bd [0:300]; bit [7:0] bk [0:300]; bit bl [0:300]; bit bu [0:300];
  int nbeats = 0;
  bit bv [0:301]; int bix [0:301]; int ncyc = 0;
  int sent_octets = 0, fail_cycle = -1;
  function automatic void load(input int n);
    int b, k;
    nbeats = (n + 7) / 8;
    for (b = 0; b < nbeats; b++) begin
      bd[b] = 64'd0; bk[b] = 8'd0; bl[b] = (b == nbeats - 1); bu[b] = 0;
      for (k = 0; k < 8; k++) if (8*b + k < n) begin bd[b][8*k +: 8] = oct[8*b + k]; bk[b][k] = 1'b1; end
    end
    ncyc = 0;
    for (b = 0; b < nbeats; b++) begin
      if (tvalid_gap && b == 3) begin bv[ncyc] = 0; bix[ncyc] = -1; ncyc++; end
      bv[ncyc] = 1; bix[ncyc] = b; ncyc++;
    end
  endfunction
  function automatic int tx_cycles();
    bit started; started = 0; sent_octets = 0; fail_cycle = -1;
    for (int c = 0; c < ncyc; c++) begin
      if (!bv[c]) begin
        if (started) begin fail_cycle = c; return 1; end
      end else begin
        started = 1;
        if (bl[bix[c]] && bu[bix[c]]) begin fail_cycle = c; return 2; end
        for (int k = 0; k < 8; k++) if (bk[bix[c]][k]) sent_octets++;
      end
    end
    return 0;
  endfunction
endmodule

// eth_pause: the PAUSE function of MAC Control (Annex 31B) at the station that receives PAUSE frames, in octet
// times (one octet time is 8 bit times; a pause quantum is 512 bit times = 64 octet times, 31B.2).
//   reset(), rx_pause(t, q)  a valid PAUSE frame with pause_time q ended at time t: the timer restarts (31B.3.3)
//   may_start(t)             1 when a new data frame may start at time t. A frame already started is never cut
//                            (31B.3.7). react is the bench's reaction time: frames may still start until t + react.
//   paused_until             the time the timer runs out
//   pause_octets(q, o[])     not here: build a PAUSE frame with eth_frame (DA 01-80-C2-00-00-01, 8808h, 0001h, q)
// Faults: pause_ignored, pause_adds_not_overrides (a new frame adds to the timer, and zero does not cancel),
//         slow_reaction (react = 70 quanta, over the 60 allowed at 10 Gb/s), timer_in_bits (q counts bit times).
module eth_pause;
  localparam int QUANTUM = 64;                     // octet times
  bit pause_ignored = 0, pause_adds_not_overrides = 0, slow_reaction = 0, timer_in_bits = 0;
  int react = 0, t_rx = -1, paused_until = 0;
  function automatic void reset(); t_rx = -1; paused_until = 0; endfunction
  function automatic void rx_pause(input int t, input int q);
    int len;
    if (pause_ignored) return;
    len = timer_in_bits ? (q + 7) / 8 : q * QUANTUM;
    if (pause_adds_not_overrides && paused_until > t) paused_until = paused_until + len;
    else paused_until = t + len;
    t_rx = t;
  endfunction
  function automatic bit may_start(input int t);
    int r;
    r = slow_reaction ? 70 * QUANTUM : react;
    if (t_rx < 0) return 1;
    if (t < t_rx + r) return 1;
    return t >= paused_until;
  endfunction
endmodule

// eth_pfc: priority-based flow control (Annex 31D). The frame is 802.3's; holding a priority's queue is the MAC
// Control client's job (IEEE 802.1Q, not held), so the eight timers here are a bench client, in octet times.
//   build(f_oct[], pev, times[])   not here: the bench writes opcode 01-01, the vector and eight times into eth_frame
//   reset(), rx(t, pev, tm[0..7])  for each e[n] = 1 (bit n of the vector's low octet), priority n stops until
//                                  t + 64 * time[n] (hold_end[n]); e[n] = 0 leaves priority n alone; time[n] = 0 releases it
//   blocked(n, t)                  1 while priority n is held
// Fault: pfc_wrong_priority (reads e[n] from bit 7 - n).
module eth_pfc;
  bit pfc_wrong_priority = 0;
  int hold_end [0:7];
  function automatic void reset(); for (int i = 0; i < 8; i++) hold_end[i] = 0; endfunction
  function automatic void rx(input int t, input [15:0] pev, input [127:0] tm);   // tm[16*n +: 16] = time[n]
    bit e;
    for (int n = 0; n < 8; n++) begin
      e = pfc_wrong_priority ? pev[7 - n] : pev[n];
      if (e) hold_end[n] = t + 64 * int'(tm[16*n +: 16]);
    end
  endfunction
  function automatic bit blocked(input int n, input int t); return t < hold_end[n]; endfunction
endmodule

// eth_csma_tx: one half-duplex transmitter (4.2.3.2), one call of tick() per octet time.
//   reset(), load(frame_octets)   a frame of frame_octets (DA to FCS) waits to be sent; it is padded to min_frame
//   tick(carrier)                 carrier: another station's signal is on the wire here now. Returns 1 when the
//                                 station puts an octet (packet or jam) on the wire.
//   plan[i]                       the wait, in slots, after collision i + 1. The bench sets it (default 0). This
//                                 readable station draws nothing and has no attempt limit.
//   state  0 idle, 1 defer, 2 send, 3 jam, 4 backoff, 5 sent (as far as the sender knows)
//   pkt, sent, quiet, left, attempts, late, last_start, last_r
// min_frame is 64 octets; a bench may lower it to show why it is 64. Fault: no_backoff (every wait is 0 slots).
// Deference is a bench simplification: the 12-octet quiet count restarts on any carrier, own or received, and the
// station never starts while carrier is present. 4.2.8 restarts only the first part of the gap, and then transmits
// whatever the carrier.
module eth_csma_tx;
  localparam int SLOT = 64, JAM = 4, GAP = 12, PRE = 8;   // octet times
  bit no_backoff = 0;
  int min_frame = 64;
  int plan [0:63];
  int state = 0, pkt = 0, sent = 0, quiet = GAP, left = 0, attempts = 0, late = 0, last_start = -1, last_r = 0, now = 0;
  function automatic void reset();
    state = 0; pkt = 0; sent = 0; quiet = GAP; left = 0; attempts = 0; late = 0; last_start = -1; last_r = 0; now = 0;
  endfunction
  function automatic void load(input int frame_octets);
    pkt = PRE + frame_octets;
    if (frame_octets < min_frame) pkt = PRE + min_frame;
    state = 1; attempts = 0; sent = 0; late = 0;
  endfunction
  function automatic bit tick(input bit carrier);
    bit on;
    on = 0;
    if (state == 1 && !carrier && quiet >= GAP) begin state = 2; sent = 0; last_start = now; end
    if (state == 2 && carrier) begin
      attempts++; if (sent > SLOT) late++;
      state = 3; left = JAM;
    end
    case (state)
      2: begin sent++; on = 1; if (sent == pkt) state = 5; end
      3: begin
           on = 1; left--;
           if (left == 0) begin
             last_r = no_backoff ? 0 : plan[(attempts - 1) % 64];
             left = SLOT * last_r;
             state = (left == 0) ? 1 : 4;
           end
         end
      4: begin left--; if (left == 0) state = 1; end
      default: ;
    endcase
    quiet = (carrier || on) ? 0 : ((quiet < GAP) ? quiet + 1 : GAP);
    now++;
    return on;
  endfunction
endmodule

// eth_csma: two eth_csma_tx stations, A and B, at the two ends of a wire with a one-way delay of d octet times.
//   run(fa, ready_a, fb, ready_b, tmax)   each station loads its frame (fa, fb octets) at its ready time
//   on_a[t], on_b[t]          what each station put on the wire at time t
//   ev_t[], ev_who[] (0 A, 1 B), ev_kind[], ev_v[], n_ev   the event log:
//     kind 0 starts attempt v; 1 sees a collision after v octets; 2 jam over, backs off v slots;
//     3 last octet sent (v = octets); 4 gives up after v attempts
//   delivered(i)              1 when station i's last attempt reached the far end with no overlap there
//   a.plan[], b.plan[], a.no_backoff, b.no_backoff, a.min_frame, b.min_frame: the stations' settings
module eth_csma;
  eth_csma_tx a(); eth_csma_tx b();
  int d = 10, n_ev = 0, tend = 0;
  bit on_a [0:16383]; bit on_b [0:16383];
  int ev_t [0:255]; int ev_who [0:255]; int ev_kind [0:255]; int ev_v [0:255];
  function automatic void log_ev(input int t, input int who, input int kind, input int v);
    if (n_ev < 256) begin ev_t[n_ev] = t; ev_who[n_ev] = who; ev_kind[n_ev] = kind; ev_v[n_ev] = v; n_ev++; end
  endfunction
  function automatic void note(input int t, input int who, input int s0, input int s1, input int sent0, input int att, input int r, input int sent1);
    if (s0 != 2 && s1 == 2) log_ev(t, who, 0, att + 1);
    if (s0 == 2 && (s1 == 3 || s1 == 4)) log_ev(t, who, 1, sent0);
    if (s0 == 3 && (s1 == 4 || s1 == 1)) log_ev(t, who, 2, r);
    if (s0 != 5 && s1 == 5) log_ev(t, who, 3, sent1);
    if (s0 != 6 && s1 == 6) log_ev(t, who, 4, att);
  endfunction
  function automatic void run(input int fa, input int ready_a, input int fb, input int ready_b, input int tmax);
    bit ca, cb; int sa, sb, xa, xb;
    a.reset(); b.reset(); n_ev = 0; tend = tmax;
    for (int t = 0; t < tmax; t++) begin
      if (t == ready_a) a.load(fa);
      if (t == ready_b) b.load(fb);
      ca = (t >= d) ? on_b[t - d] : 1'b0;
      cb = (t >= d) ? on_a[t - d] : 1'b0;
      sa = a.state; sb = b.state; xa = a.sent; xb = b.sent;
      on_a[t] = a.tick(ca);
      on_b[t] = b.tick(cb);
      note(t, 0, sa, a.state, xa, a.attempts, a.last_r, a.sent);
      note(t, 1, sb, b.state, xb, b.attempts, b.last_r, b.sent);
    end
  endfunction
  function automatic bit delivered(input int i);
    int s, p, u;
    if (i == 0 && a.state != 5) return 0;
    if (i == 1 && b.state != 5) return 0;
    s = (i == 0) ? a.last_start : b.last_start;
    p = (i == 0) ? a.pkt : b.pkt;
    for (int t = s; t < s + p; t++) begin
      u = t + d;
      if (u < tend && ((i == 0) ? on_b[u] : on_a[u])) return 0;
    end
    return 1;
  endfunction
endmodule

// eth_gap: how long the gap before the next Start is on a 4-lane XGMII, where Start must sit on lane 0
// (46.3.1.4). A gap counts every character from the Terminate to the last idle before Start. A packet is
// 8 + n characters (Start, six preamble octets, SFD, an n-octet frame) and starts on lane 0.
//   reset()                     DIC = 0 (the count is reset only at initialisation)
//   method                      0 deficit idle count, 1 always insert (both allowed by 46.3.1.4)
//   next_gap(n, mac_gap)        the gap after an n-octet frame when the MAC asks for mac_gap (12 or more)
//   deleted, inserted, dic      what the last call did, and the count after it
// Faults: ipg_min_only (always deletes, ignoring the bound), dic_max4 (bounds the count at 4, not 3),
//         start_any_lane (no alignment: the gap is always mac_gap).
module eth_gap;
  bit ipg_min_only = 0, dic_max4 = 0, start_any_lane = 0;
  int method = 0, dic = 0, deleted = 0, inserted = 0;
  function automatic void reset(); dic = 0; deleted = 0; inserted = 0; endfunction
  function automatic int next_gap(input int n, input int mac_gap);
    int m, top;
    deleted = 0; inserted = 0;
    m = (n + mac_gap) % 4;                       // lanes past lane 0 the next Start would land on
    if (start_any_lane || m == 0) return mac_gap;
    top = dic_max4 ? 4 : 3;
    if (method == 0 && (ipg_min_only || dic + m <= top)) begin deleted = m; dic = dic + m; end
    else begin inserted = 4 - m; if (method == 0) dic = dic - (4 - m); end
    return mac_gap - deleted + inserted;
  endfunction
endmodule
Read included file: eth_pcs.sv
`timescale 1ns/1ns
// eth_pcs.sv: the 1000BASE-X PCS, transmit side and synchronization (read-only). It sits on hs_8b10b (hs_code.sv).

// eth_1000x: the transmit ordered-set layer (36.2.4). The stream is kept as {k, d} and as ten coded bits.
//   clear()            empty stream, running disparity negative
//   idle(k)            k idle ordered sets. Each tests the running disparity first (Figure 36-6):
//                      positive -> /I1/ (K28.5 D5.6), negative -> /I2/ (K28.5 D16.2)
//   cfg(word, k)       k configuration ordered sets, /C1/ and /C2/ in turn: K28.5, D21.5 or D2.2, word[7:0], word[15:8]
//   start_packet()     /S/ in place of the first preamble octet, then six 55h and D5h
//   data(d)            one data code-group
//   end_packet()       /T/ /R/, and one more /R/ when the first /R/ went out on an even position
//   err()              /V/
//   put(k, d)          any code-group
//   n                  code-groups so far; code-group i is even-numbered when i is even
//   sym[i] = {k, d};  code[i] = abcdei fghj, bit a (code[i][9]) is sent first;  rdb[i] = running disparity before i
//   is_k(i, d), comma_plus(), comma_minus()
// Fault: idle_wrong_disparity (every idle is /I2/, so a positive running disparity is never corrected).
module eth_1000x;
  bit idle_wrong_disparity = 0;
  hs_8b10b c8();
  bit [8:0] sym [0:8191]; bit [9:0] code [0:8191]; bit rdb [0:8191];
  int n = 0; bit c2 = 0;
  function automatic void clear(); n = 0; c2 = 0; c8.rd_tx = 0; endfunction
  function automatic void put(input bit k, input [7:0] d);
    sym[n] = {k, d}; rdb[n] = c8.rd_tx; code[n] = c8.enc(d, k); n++;
  endfunction
  function automatic void idle(input int k);
    bit positive;
    for (int i = 0; i < k; i++) begin
      positive = c8.rd_tx && !idle_wrong_disparity;
      put(1'b1, 8'hbc);                                // K28.5
      put(1'b0, positive ? 8'hc5 : 8'h50);             // D5.6 or D16.2
    end
  endfunction
  function automatic void cfg(input [15:0] word, input int k);
    for (int i = 0; i < k; i++) begin
      put(1'b1, 8'hbc);
      put(1'b0, c2 ? 8'h42 : 8'hb5);                   // D2.2 or D21.5
      put(1'b0, word[7:0]); put(1'b0, word[15:8]);
      c2 = !c2;
    end
  endfunction
  function automatic void data(input [7:0] d); put(1'b0, d); endfunction
  function automatic void start_packet();
    put(1'b1, 8'hfb);                                  // /S/ = K27.7
    for (int i = 0; i < 6; i++) put(1'b0, 8'h55);
    put(1'b0, 8'hd5);
  endfunction
  function automatic void end_packet();
    put(1'b1, 8'hfd);                                  // /T/ = K29.7
    put(1'b1, 8'hf7);                                  // /R/ = K23.7
    if (n % 2 != 0) put(1'b1, 8'hf7);                  // that /R/ was even-numbered: one more
  endfunction
  function automatic void err(); put(1'b1, 8'hfe); endfunction     // /V/ = K30.7
  function automatic bit is_k(input int i, input [7:0] d); return sym[i] == {1'b1, d}; endfunction
  function automatic int comma_plus();
    int c; c = 0;
    for (int i = 0; i < n; i++) if (code[i][9:3] == 7'b0011111) c++;
    return c;
  endfunction
  function automatic int comma_minus();
    int c; c = 0;
    for (int i = 0; i < n; i++) if (code[i][9:3] == 7'b1100000) c++;
    return c;
  endfunction
endmodule

// eth_1000x_sync: the synchronization process of Figure 36-9, one call of rx() per ten-bit code-group.
//   reset()            LOSS_OF_SYNC
//   rx(code)           takes one code-group; returns sync_status (1 = OK)
//   state              0 LOSS_OF_SYNC, 1 COMMA_DETECT_1, 2 ACQUIRE_SYNC_1, 3 COMMA_DETECT_2, 4 ACQUIRE_SYNC_2,
//                      5 COMMA_DETECT_3, 6 SYNC_ACQUIRED_1, 7 SYNC_ACQUIRED_2, 8 SYNC_ACQUIRED_2A,
//                      9 SYNC_ACQUIRED_3, 10 SYNC_ACQUIRED_3A, 11 SYNC_ACQUIRED_4, 12 SYNC_ACQUIRED_4A
//   even               the code-group just taken was even-numbered
//   good_cgs, bad_seen (every bad code-group since reset), k, d (the last decode)
// A code-group is bad when it is invalid, or when it holds a comma and is odd-numbered (36.2.5.1.3).
// Bench choices: in LOSS_OF_SYNC the decoder takes its running disparity from the comma it finds; an invalid
// code-group leaves the decoder's running disparity as the received bits set it.
module eth_1000x_sync;
  hs_8b10b c8();
  int state = 0, good_cgs = 0, bad_seen = 0;
  bit even = 0, sync = 0, rd = 0, k = 0; bit [7:0] d = 0;
  function automatic void reset(); state = 0; good_cgs = 0; bad_seen = 0; even = 0; sync = 0; rd = 0; endfunction
  function automatic bit rx(input [9:0] code);
    reg [11:0] r; bit invalid, comma, is_d, bad;
    comma = code[9:3] == 7'b0011111 || code[9:3] == 7'b1100000;
    if (state == 0 && comma) rd = (code[9:3] == 7'b1100000);
    r = c8.decode(code, rd);                           // {rd_out, disp_err, code_err, k, d}
    rd = r[11]; k = r[8]; d = r[7:0];
    invalid = r[10] || r[9];
    is_d = !invalid && !r[8];
    bad = invalid || (comma && even);                  // even: the one before was even, so this one is odd
    if (bad && state != 0) bad_seen++;
    case (state)
      0: begin if (comma) begin state = 1; even = 1; end else even = !even; end
      1, 3, 5: begin even = 0; state = is_d ? state + 1 : 0; end
      2, 4: begin
        if (bad) state = 0;
        else if (comma) begin state = state + 1; even = 1; end
        else even = !even;
      end
      6: begin even = !even; if (bad) begin state = 7; good_cgs = 0; end end
      7, 9, 11: begin
        even = !even;
        if (bad) begin state = (state == 11) ? 0 : state + 2; good_cgs = 0; end
        else begin state = state + 1; good_cgs = 1; end
      end
      default: begin                                   // 8, 10, 12: counting good code-groups
        even = !even;
        if (bad) begin state = (state == 12) ? 0 : state + 1; good_cgs = 0; end
        else if (good_cgs == 3) begin state = (state == 8) ? 6 : state - 3; good_cgs = 0; end
        else good_cgs++;
      end
    endcase
    sync = state >= 6;
    return sync;
  endfunction
endmodule

// ---- 10GBASE-R and 25GBASE-R: 64B/66B blocks (Clause 49; Clause 107 uses the same code) ----
// Eight XGMII characters are one vector raw[71:0] (49.2.13.2.2): raw[k] is the control flag of character k,
// raw[8 + 8*k +: 8] its octet. A block is blk[65:0]; bit 0 is sent first. blk[1:0] is the sync header,
// blk[9:2] the block type field of a control block, the rest the payload (Figure 49-7).

// eth_66: the control blocks that hold no Start, no Terminate and no frame data.
//   c_code(x)       Table 49-1: the 7-bit C code of XGMII control code x; 7Fh if x is not in the table
//   enc_ctrl(raw)   {ok, blk}: block type 1Eh (eight control characters), 2Dh (four, then an ordered set),
//                   4Bh (an ordered set, then four) or 55h (two ordered sets); ok = 0 if raw is none of these.
//                   It only lays out the fields. Whether the vector may be sent is the transmit process's
//                   decision (eth_66_tx).
//   on_wire(blk)    the 66 bits as text in the order they are sent: sync, block type, payload
//   ham(a, b)       how many bits differ between two block type values
// Fault: wrong_block_type (types 2Dh and 4Bh are swapped).
module eth_66;
  bit wrong_block_type = 0;
  function automatic [6:0] c_code(input [7:0] x);
    case (x)
      8'h07: return 7'h00;                             // idle
      8'h06: return 7'h06;                             // low power idle
      8'hfe: return 7'h1e;                             // error
      8'h1c: return 7'h2d;                             // the six reserved characters
      8'h3c: return 7'h33;
      8'h7c: return 7'h4b;
      8'hbc: return 7'h55;
      8'hdc: return 7'h66;
      8'hf7: return 7'h78;
      default: return 7'h7f;
    endcase
  endfunction
  function automatic [7:0] ch(input [71:0] raw, input int k); return raw[8 + 8*k +: 8]; endfunction
  // characters k to k+3 are a sequence ordered set: 9Ch with its flag, then three data octets
  function automatic bit is_q(input [71:0] raw, input int k);
    return raw[k] && ch(raw, k) == 8'h9c && !raw[k + 1] && !raw[k + 2] && !raw[k + 3];
  endfunction
  // characters k to k+3 are control characters with a C code
  function automatic bit is_c4(input [71:0] raw, input int k);
    for (int j = k; j < k + 4; j++) if (!raw[j] || c_code(ch(raw, j)) == 7'h7f) return 0;
    return 1;
  endfunction
  function automatic [66:0] enc_ctrl(input [71:0] raw);
    reg [65:0] b; bit q0, q4, c0, c4;
    b = 66'd0;
    b[1:0] = 2'b01;                                    // sync header "10": bit 0, sent first, is 1
    q0 = is_q(raw, 0); q4 = is_q(raw, 4); c0 = is_c4(raw, 0); c4 = is_c4(raw, 4);
    if (c0 && c4) b[9:2] = 8'h1e;
    else if (c0 && q4) b[9:2] = wrong_block_type ? 8'h4b : 8'h2d;
    else if (q0 && c4) b[9:2] = wrong_block_type ? 8'h2d : 8'h4b;
    else if (q0 && q4) b[9:2] = 8'h55;
    else return 67'd0;
    if (c0) for (int k = 0; k < 4; k++) b[10 + 7*k +: 7] = c_code(ch(raw, k));
    else begin b[33:10] = raw[39:16]; b[37:34] = 4'h0; end     // D1 to D3, then the O code of the sequence set
    if (c4) for (int k = 4; k < 8; k++) b[10 + 7*k +: 7] = c_code(ch(raw, k));
    else begin b[41:38] = 4'h0; b[65:42] = raw[71:48]; end     // the O code, then D5 to D7
    return {1'b1, b};
  endfunction
  function automatic string on_wire(input [65:0] blk);
    string s;
    s = "";
    for (int i = 0; i < 66; i++) begin
      if (i == 2 || i == 10) s = {s, " "};
      s = {s, blk[i] ? "1" : "0"};
    end
    return s;
  endfunction
  function automatic int ham(input [7:0] a, input [7:0] b);
    int n; reg [7:0] x;
    x = a ^ b; n = 0;
    for (int i = 0; i < 8; i++) if (x[i]) n++;
    return n;
  endfunction
endmodule

// eth_66_tx: the transmit state diagram (Figure 49-16) without the EEE state. One call per vector.
//   step(t)   t is the T_TYPE of the vector: 0 C (control), 1 S (start), 2 T (terminate), 3 D (data), 4 E (none of these).
//             Returns 1 if the vector is encoded and sent, 0 if the error block goes out in its place.
//   state     0 TX_INIT, 1 TX_C, 2 TX_D, 3 TX_T, 4 TX_E
module eth_66_tx;
  int state = 0;
  function automatic void reset(); state = 0; endfunction
  function automatic bit step(input int t);
    case (state)
      0, 1, 3: state = (t == 0) ? 1 : (t == 1) ? 2 : 4;                    // TX_INIT, TX_C, TX_T: only C or S may follow
      2: state = (t == 3) ? 2 : (t == 2) ? 3 : 4;                          // TX_D: only D or T may follow
      default: state = (t == 2) ? 3 : (t == 3) ? 2 : (t == 0) ? 1 : 4;     // TX_E: T, D or C leave it
    endcase
    return state != 4;
  endfunction
endmodule

// eth_66_comp: clock compensation on XGMII columns (49.2.4.7, 49.2.4.10). Call once per column, in order.
// A column is {c[3:0], d[31:0]}: lane k is flag c[k] and octet d[8k+7:8k].
//   can_delete(c, d)   1 if this column may be dropped: four idles that hold none of the first four characters
//                      after a Terminate, or the second of two consecutive sequence ordered sets
//   can_insert(c, d)   1 if an idle column may be added after this one: it is idle or an ordered set
module eth_66_comp;
  bit guard = 0, prev_seq = 0;
  function automatic void reset(); guard = 0; prev_seq = 0; endfunction
  function automatic bit is_seq(input [3:0] c, input [31:0] d); return c == 4'b0001 && d[7:0] == 8'h9c; endfunction
  function automatic bit is_idle(input [3:0] c, input [31:0] d); return c == 4'b1111 && d == 32'h07070707; endfunction
  function automatic bit can_delete(input [3:0] c, input [31:0] d);
    bit ok, has_t;
    has_t = 0;
    for (int k = 0; k < 4; k++) if (c[k] && d[8*k +: 8] == 8'hfd) has_t = 1;
    ok = (is_idle(c, d) && !guard) || (is_seq(c, d) && prev_seq);
    guard = has_t;                                     // the next column holds some of the four characters after /T/
    prev_seq = is_seq(c, d) && !ok;                    // only one of the two
    return ok;
  endfunction
  function automatic bit can_insert(input [3:0] c, input [31:0] d); return is_idle(c, d) || is_seq(c, d); endfunction
endmodule

// eth_66_scr: the scrambler and the descrambler of 10GBASE-R (49.2.6, 49.2.10; Figures 49-8 and 49-10).
// The register is s[57:0]: stage S0 is s[0] and holds the newest line bit. Use one instance to scramble and
// another to descramble.
//   scr_bit(b)       one payload bit in, one line bit out: b XOR S38 XOR S57. The line bit shifts into S0.
//   dscr_bit(b)      one line bit in, one payload bit out: the same XOR. The received bit shifts into S0.
//   scramble(blk)    a whole block: bits 1:0 (the sync header) pass, bits 2 to 65 are scrambled in that order
//   descramble(blk)  the reverse
//   load(v)          sets the register (the standard asks for no start value)
// Fault: scrambles_header (the two sync header bits go through the scrambler too).
module eth_66_scr;
  bit [57:0] s = 58'd0;
  bit scrambles_header = 0;
  function automatic void load(input [57:0] v); s = v; endfunction
  function automatic bit scr_bit(input bit b);
    bit o; o = b ^ s[38] ^ s[57]; s = {s[56:0], o}; return o;
  endfunction
  function automatic bit dscr_bit(input bit b);
    bit o; o = b ^ s[38] ^ s[57]; s = {s[56:0], b}; return o;
  endfunction
  function automatic [65:0] scramble(input [65:0] blk);
    reg [65:0] o; o = blk;
    for (int i = scrambles_header ? 0 : 2; i < 66; i++) o[i] = scr_bit(blk[i]);
    return o;
  endfunction
  function automatic [65:0] descramble(input [65:0] blk);
    reg [65:0] o; o = blk;
    for (int i = 2; i < 66; i++) o[i] = dscr_bit(blk[i]);
    return o;
  endfunction
endmodule

// eth_prbs31: the PRBS31 pattern generator (49.2.8, Figure 49-9). The register is s[30:0], stage S0 is s[0].
//   gen_bit()   the next pattern bit: S27 XOR S30 shifts into S0, and the output is that bit inverted
// The register must not be all zeros: it would stay there. The checker is not in this file.
module eth_prbs31;
  bit [30:0] s = 31'h7fffffff;
  function automatic bit gen_bit();
    bit f; f = s[27] ^ s[30]; s = {s[29:0], f}; return !f;
  endfunction
endmodule

// eth_66_test: the square wave of 49.2.8 and the two data patterns of the pseudo-random test pattern.
//   sq_bit()        square wave: sq_n ones, then sq_n zeros (sq_n may be 4 to 11)
//   pattern()       the 64-bit data pattern: zeros, or the payload of a block with two local fault sets (lf_pattern)
// The pseudo-random pattern generator and its checker (49.2.8, 49.2.12) are not in this file.
module eth_66_test;
  eth_66 code();
  bit lf_pattern = 0;
  int sq_n = 8, sq_k = 0;
  function automatic void restart(); sq_k = 0; endfunction
  function automatic bit sq_bit();
    bit b; b = (sq_k < sq_n); sq_k = (sq_k + 1) % (2 * sq_n); return b;
  endfunction
  function automatic [63:0] pattern();
    reg [66:0] r;
    if (!lf_pattern) return 64'd0;
    r = code.enc_ctrl({64'h0100009c_0100009c, 8'h11}); return r[65:2];
  endfunction
endmodule

// eth_66_loop: PCS loopback (49.2.14.4), switched by MDIO bit 3.0.14.
//   rx_block(from_tx, from_pma)   what the receive path decodes: its own transmit block when loopback is 1
//   pma_word(w)                   what goes to the PMA: the word 00FFh when loopback is 1, else w
module eth_66_loop;
  bit loopback = 0;
  function automatic [65:0] rx_block(input [65:0] from_tx, input [65:0] from_pma); return loopback ? from_tx : from_pma; endfunction
  function automatic [15:0] pma_word(input [15:0] w); return loopback ? 16'h00ff : w; endfunction
endmodule
Read included file: hs_blk.sv
`timescale 1ns/1ns
// hs_blk.sv: block codes (read-only). A block is a sync header and a payload. Headers are written as
// they go on the wire, most significant bit first ("01" sends 0, then 1). The payload is sent bit 0
// first and is scrambled with a self-synchronising x^58 + x^39 + 1 scrambler (the header never is).
// Every layout uses that 64b/66b-style scrambler. USB 3.2 Gen 2 (§6.3.2.3) and USB4 (§4.3.1.5) use an
// additive x^23 LFSR kept in step by ordered sets instead; that is not modelled here (hs_scr has the
// polynomial as use_x23_usb3() for a scrambler on its own). Set scramble = 0 / descramble = 0 for none.
//   use_66()        64b/66b: data 01, control 10 (USB4 v2.0 Figure 4-22/4-23)
//   use_132_usb4()  128b/132b: data 0101, ordered set 1010 (USB4 v2.0 Figure 4-22/4-23)
//   use_132_usb3()  128b/132b: data 0011b, control 1100b, bit 0 first (USB 3.2 §6.3.2.2, Figure 6-11),
//                   so on the wire data is 1100 and control is 0011
//   use_130()       128b/130b with the 64b/66b header values: a bench layout (PCIe's own values are unverified)
// hs_blk (transmitter): blk_tx(payload, ctrl) -> the block in the low n bits, bit n-1 sent first.
// hs_blk_lock (receiver): push(b) one line bit at a time; returns 1 when a block with a valid header is
//   complete and locked (then hdr, ctrl and payload hold it). A locked block with an invalid header is not
//   delivered: push returns 0, hdr_ok is 0 and hdr_errs counts it. USB 3.2's single-bit header correction
//   (§6.3.2.2) is not modelled. Lock after lock_good valid headers in a row; an invalid header
//   before lock slips the boundary by one bit; once locked, bad_limit invalid headers within a window of
//   bad_window blocks lose lock. The default counts (64, 64, 16) are those of IEEE 802.3 Figure 49-14 (read 2026-11-14).
// hs_gearbox: a bit FIFO between a block width and a word width: gb_push(v, n), gb_pop(n), gb_level().
// Faults: header_00 (hs_blk sends 00 on every block), lock_on_first and never_unlock (hs_blk_lock).
module hs_blk;
  int hdr_bits = 2, pay_bits = 64; bit [3:0] hdr_data = 4'b0001, hdr_ctrl = 4'b0010;
  bit scramble = 1, header_00 = 0, trace = 0; int blocks = 0;
  hs_scr scr(); bit ready = 0;
  // set up on first use (an initial block here could run after the bench's first call)
  function automatic void prep(); if (!ready) begin scr.use_x58(); scr.s = 64'h3ff_ffff_ffff_ffff; ready = 1; end endfunction
  function automatic void set(input int h, input int p, input [3:0] d, input [3:0] c); hdr_bits = h; pay_bits = p; hdr_data = d; hdr_ctrl = c; endfunction
  function automatic void use_66(); set(2, 64, 4'b0001, 4'b0010); endfunction
  function automatic void use_130(); set(2, 128, 4'b0001, 4'b0010); endfunction
  function automatic void use_132_usb4(); set(4, 128, 4'b0101, 4'b1010); endfunction
  function automatic void use_132_usb3(); set(4, 128, 4'b1100, 4'b0011); endfunction
  function automatic int n(); return hdr_bits + pay_bits; endfunction
  function automatic [131:0] blk_tx(input [127:0] payload, input bit ctrl);
    reg [131:0] v; reg [3:0] h; int m; prep(); m = n(); v = 132'd0;
    h = header_00 ? 4'd0 : ctrl ? hdr_ctrl : hdr_data;
    for (int i = 0; i < hdr_bits; i++) v[m - 1 - i] = h[hdr_bits - 1 - i];
    for (int i = 0; i < pay_bits; i++) v[m - 1 - hdr_bits - i] = scramble ? scr.scr_bit(payload[i]) : payload[i];
    if (trace) $display("b%0d TX %s", blocks, ctrl ? "ctrl" : "data");
    blocks++;
    return v;
  endfunction
endmodule

module hs_blk_lock;
  int hdr_bits = 2, pay_bits = 64; bit [3:0] hdr_data = 4'b0001, hdr_ctrl = 4'b0010;
  int lock_good = 64, bad_window = 64, bad_limit = 16;
  bit descramble = 1, lock_on_first = 0, never_unlock = 0, trace = 0;
  bit locked = 0; int nbits = 0, pos = 0, slips = 0, good_run = 0, hdr_errs = 0, blocks = 0, lock_at = -1, unlocks = 0, win_n = 0, win_bad = 0;
  bit [131:0] sh = 132'd0; bit [3:0] hdr; bit ctrl; bit hdr_ok = 0; bit [127:0] payload;
  hs_scr dscr(); bit ready = 0;
  function automatic void set(input int h, input int p, input [3:0] d, input [3:0] c); hdr_bits = h; pay_bits = p; hdr_data = d; hdr_ctrl = c; endfunction
  function automatic void use_66(); set(2, 64, 4'b0001, 4'b0010); endfunction
  function automatic void use_130(); set(2, 128, 4'b0001, 4'b0010); endfunction
  function automatic void use_132_usb4(); set(4, 128, 4'b0101, 4'b1010); endfunction
  function automatic void use_132_usb3(); set(4, 128, 4'b1100, 4'b0011); endfunction
  function automatic void restart(); locked = 0; nbits = 0; pos = 0; slips = 0; good_run = 0; hdr_errs = 0; blocks = 0; lock_at = -1; unlocks = 0; win_n = 0; win_bad = 0; endfunction
  function automatic bit push(input bit b);
    int m; reg ok; m = hdr_bits + pay_bits;
    if (!ready) begin dscr.use_x58(); ready = 1; end
    sh = {sh[130:0], b}; nbits++; pos++;
    if (pos < m) return 0;
    pos = 0; hdr = 4'd0;
    for (int i = 0; i < hdr_bits; i++) hdr[hdr_bits - 1 - i] = sh[m - 1 - i];
    ok = (hdr == hdr_data) || (hdr == hdr_ctrl); ctrl = (hdr == hdr_ctrl); hdr_ok = ok;
    blocks++;
    if (!ok) hdr_errs++;
    if (!locked) begin
      if (ok) begin
        good_run++;
        if (good_run >= (lock_on_first ? 1 : lock_good)) begin
          locked = 1; win_n = 0; win_bad = 0; if (lock_at < 0) lock_at = nbits;
          if (trace) $display("b%0d LOCK bit=%0d slips=%0d", blocks, nbits, slips);
        end
      end else begin good_run = 0; pos = -1; slips++; end
      return 0;
    end
    win_n++; if (!ok) win_bad++;
    if (win_bad >= bad_limit && !never_unlock) begin
      locked = 0; good_run = 0; unlocks++; pos = -1; slips++;
      if (trace) $display("b%0d UNLOCK bit=%0d", blocks, nbits);
      return 0;
    end
    if (win_n >= bad_window) begin win_n = 0; win_bad = 0; end
    // the descrambler still takes the payload bits of a bad block, so it stays in step
    for (int i = 0; i < pay_bits; i++) payload[i] = descramble ? dscr.dscr_bit(sh[m - 1 - hdr_bits - i]) : sh[m - 1 - hdr_bits - i];
    return ok;
  endfunction
endmodule

module hs_gearbox;
  bit q [0:1023]; int head = 0, count = 0, overflows = 0;
  function automatic void gb_push(input [131:0] v, input int n);   // bit n-1 first
    for (int i = n - 1; i >= 0; i--) begin
      if (count == 1024) overflows++; else begin q[(head + count) % 1024] = v[i]; count++; end
    end
  endfunction
  function automatic int gb_level(); return count; endfunction
  function automatic [131:0] gb_pop(input int n);                    // the oldest bit lands in bit n-1
    reg [131:0] w; w = 132'd0;
    for (int i = n - 1; i >= 0 && count > 0; i--) begin w[i] = q[head]; head = (head + 1) % 1024; count--; end
    return w;
  endfunction
endmodule
ConceptHow does a 10GBASE-R receiver get block lock?
ConceptA locked receiver gets 16 invalid headers in one window of 64. What does it do?
ConceptWhich bits of a 66-bit block pass through the scrambler?
ConceptA 10GBASE-R link has block lock. In one 125 µs period 20 invalid headers arrive. What reaches the XGMII once the 16th has arrived?

Common Mistakes

Wrong Lock on the first valid sync header.

At a wrong position half the headers are valid by chance. The lock is false and will not last.

Fix Ask for 64 valid headers in a row before block lock is set.

Wrong Count 16 invalid headers over any 64 headers in a row.

The diagram has no sliding window. Its counters start again when a window ends.

Fix Count in fixed windows that follow one another.

Wrong Clear hi_ber as soon as a valid header arrives.

hi_ber would flicker on a link that is still bad.

Fix Clear it only when a whole timer period ends with fewer than 16 invalid headers.

Wrong Scramble all 66 bits of the block.

The header would look like payload, and the receiver could never find the boundary.

Fix Scramble the 64 payload bits. Send the two header bits as they are.

Remember

  • Block lock needs 64 valid sync headers in a row. Out of lock, one invalid header slips the guess by one bit.
  • In lock, only 16 invalid headers in one window of 64 clear it. The windows do not slide.
  • The scrambler skips the sync header. One flipped line bit becomes three wrong payload bits.
  • Sixteen invalid headers in 125 µs set hi_ber. It clears at the end of a period with fewer.
  • Without lock, or with hi_ber, the receiver sends local fault.

Practice

Report a problem with this page