AHB5 Security and Memory Types

Read HPROT[6:0] as a memory type and know what Device and Normal memory allow a bridge or cache to do. Map legacy HPROT[3:0], and mark transfers Non-secure with HNONSEC.

You Will Be Able To

  • Name the memory type of any permitted HPROT[6:2] value.
  • Say what a cache or bridge may and may not do to Device and to Normal transfers.
  • Map a component with only HPROT[3:0] onto HPROT[6:0].
  • State the rules for HNONSEC.
Lesson
P4.13
Time
30 min
Runs on
Your browser
Check
5 questions

A team put a small cache in front of an AHB peripheral to speed up its status reads. The peripheral's receive FIFO sat in the same window. Its driver marked those transfers Modifiable, so the cache prefetched a whole line and merged the reads. Every prefetch popped four words, and bytes vanished from the stream.

Five Transfers, Five Attribute SetsEdges 4 to 8 of the example. The monitor names the memory type from HPROT[6:2] at each accepted address phase.
  • Manager
  • Subordinate
HPROTHNONSECManagersets HPROT and HNONSECSubordinateor a cache or bridge
HPROT→ SubordinateHNONSEC→ SubordinateManagersets HPROT and HNONSECSubordinateor a cache or bridge

HPROT is printed as bits 6 to 0.

01234clkhtransNONSEQhaddr100104100104108hwritehprot00000110000111000101111111111000010hnonsectypeDevice-nEDevice-ENormal NCWB Shareablenot permitted
Scroll horizontally ↔
  1. Cycle 0

    HPROT 0000011: Device-nE. The write response must come from the peripheral itself.

  2. Cycle 1

    Bit 2 set: Device-E. An early write response is allowed.

  3. Cycle 2

    Bit 3 set: Modifiable, so Normal memory. A cache may merge, prefetch or resize this transfer.

  4. Cycle 3

    All seven bits: Write-back, Shareable, with Allocate. HNONSEC 1 makes it Non-secure.

  5. Cycle 4

    Shareable without Modifiable: Table 3-7 has no such row. Device memory must have bit 6 low.

The opening bug was a FIFO marked Normal: bit 3 set where only Device was safe.

Seven HPROT Bits

AHB-Lite had four HPROT bits. AHB5 adds three, behind the Extended_Memory_Types property. Bit 3 kept its meaning but was renamed from Cacheable to Modifiable.

BitNameWhen 1
0Data/InstA data access; 0 is an instruction fetch, given as a hint
1PrivilegedA privileged access
2BufferableWith bits 4 and 3 low, the write response may come from an intermediate point
3ModifiableThe transfer's characteristics may be changed
4LookupThe transfer must be looked up in a cache
5AllocateAllocating it in the cache is recommended
6ShareableThe region is shared, so the response waits until other managers can see the transfer

IHI 0033C Table 3-6. HPROT keeps the timing of the address and stays constant through a burst.

Only the combinations of Table 3-7 are permitted: two Device types, then Normal Non-cacheable, Write-through and Write-back, each Shareable or not. The example's last transfer sets Shareable on a Device type, and the monitor reports it as not permitted.

Device or Normal: What the Fabric May Do

Device memory (bit 3 low)

read data from the final destination
no split, no merge, no prefetch
no change of HSIZE
same manager, same subordinate: in order
bursts may be broken into smaller bursts,
  with the same number of transfers
HPROT may only lose Bufferable

Every access happens exactly as issued. Device-nE also needs the write response from the final destination.

Normal memory (bit 3 high)

reads may be speculative
reads may fetch more data than asked
writes may be merged
HBURST and HSIZE may change
overlapping accesses stay in order
Shareable: respond only when visible

Correct for memory that has no side effects. Wrong for a FIFO, as the opening story shows.

Write-through and Write-back add cache lookups and allow the write response from a cache. Write-back writes need never reach the final destination.

Legacy HPROT and HNONSEC

A component with only HPROT[3:0] maps onto the extended types by Table 3-8. Only bits 3 and 2 matter for the type.

HPROT[3:2]Old meaningHPROT[6,4,3,2]Memory type
00Non-cacheable, Non-bufferable0000Device-nE
01Non-cacheable, Bufferable0001Device-E
10Cacheable, Non-bufferable1110Write-through, Shareable
11Cacheable, Bufferable1111Write-back, Shareable

IHI 0033C 3.9.7. Going the other way, the higher bits can simply be removed.

A manager that cannot generate accurate protection is recommended to send 0011: Non-cacheable, Non-bufferable, privileged data. Subordinates should then not rely on HPROT.

HNONSEC exists when the interface declares Secure_Transfers. It is 1 for a Non-secure transfer, it is an address phase signal, and it must stay constant through a burst. Lesson P4.14 adds the user and parity signals of AHB5.

Asked in interviews: AHB5 memory types
  1. What separates Device from Normal memory on AHB5?

    HPROT[3], Modifiable. Device transfers must reach the destination exactly as issued; Normal ones may be merged, resized or prefetched.

  2. What is the difference between Device-nE and Device-E?

    Device-E allows an early write response from an intermediate point; Device-nE needs it from the final destination.

  3. Can a Device transfer be Shareable?

    No. HPROT[6] must be zero for Device memory.

  4. What does HNONSEC = 1 mean?

    A Non-secure transfer. It is an address phase signal and must not change inside a burst.

Try It

Each line is one accepted address phase. The memory itself ignores every attribute, so all five transfers complete. The monitor shows what a cache, a bridge or a firewall would see. The base checker has no rule about HPROT values, so it counts no broken rule.

Change the last transfer to prot = 4'b1010; prot_ext = 3'b100; and it becomes Normal Non-cacheable Shareable. Try prot_ext = 3'b010; with prot = 4'b0011;: Allocate without Lookup on Device memory, which Table 3-7 does not permit either.

RUNIcarus Verilog · in your browser
Edit the code, then run it
Expected: attr e4: write 0x100 Device-nE, Secure, privileged, data attr e5: write 0x104 Device-E, Secure, privileged, data attr e6: read 0x100 Normal Non-cacheable Non-shareable, Secure, privileged, data attr e7: read 0x104 Write-back Shareable allocate, Non-secure, privileged, data attr e8: write 0x108 not permitted (Table 3-7), Non-secure, privileged, instruction checker: 5 transfers, 0 wait edges, 0 errors, 0 rules broken
Read included file: ahb_pkg.sv
`timescale 1ns/1ns
// ahb_pkg.sv: the encodings and the arithmetic of a burst (read-only).
// The memory, the driver, the checker and the lesson text all use these functions, so they never
// disagree about the address of a beat or the lanes it uses.
package ahb_pkg;
  localparam logic [1:0] IDLE = 2'b00, BUSY = 2'b01, NONSEQ = 2'b10, SEQ = 2'b11;
  localparam logic [2:0] SINGLE = 3'b000, INCR = 3'b001, WRAP4 = 3'b010, INCR4 = 3'b011,
                         WRAP8 = 3'b100, INCR8 = 3'b101, WRAP16 = 3'b110, INCR16 = 3'b111;
  localparam logic OKAY = 1'b0, ERROR = 1'b1;

  function automatic string trans_name(input logic [1:0] t);
    case (t) IDLE: return "IDLE"; BUSY: return "BUSY"; NONSEQ: return "NONSEQ"; default: return "SEQ"; endcase
  endfunction
  function automatic string burst_name(input logic [2:0] b);
    case (b)
      SINGLE: return "SINGLE"; INCR: return "INCR"; WRAP4: return "WRAP4"; INCR4: return "INCR4";
      WRAP8: return "WRAP8"; INCR8: return "INCR8"; WRAP16: return "WRAP16"; default: return "INCR16";
    endcase
  endfunction
  function automatic string resp_name(input logic r);
    return r ? "ERROR" : "OKAY";
  endfunction
  // s when c is 1, else the empty string (a string-typed result prints the same on every simulator).
  function automatic string opt(input bit c, input string s);
    if (c) return s;
    return "";
  endfunction

  // Beats in a burst: 1 for SINGLE, 4, 8 or 16 for the fixed bursts, 0 for INCR (undefined length).
  function automatic int beats_of(input logic [2:0] b);
    case (b) SINGLE: return 1; INCR: return 0; WRAP4, INCR4: return 4; WRAP8, INCR8: return 8; default: return 16; endcase
  endfunction
  function automatic bit is_wrap(input logic [2:0] b);
    return b == WRAP4 || b == WRAP8 || b == WRAP16;
  endfunction

  // The address of the beat after the one at a: the size in bytes further on; a wrapping burst
  // returns to the start of its window (beats x size bytes, aligned to that total) at the window's end.
  function automatic int unsigned next_addr(input int unsigned a, input logic [2:0] size, input logic [2:0] b);
    int unsigned nb = 1 << size;
    int unsigned window = nb * beats_of(b);
    int unsigned base;
    if (!is_wrap(b)) return a + nb;
    base = (a / window) * window;
    if (a + nb >= base + window) return base;
    return a + nb;
  endfunction

  // The address of beat n of a burst that starts at start.
  function automatic int unsigned beat_addr(input int unsigned start, input logic [2:0] size, input logic [2:0] b, input int n);
    int unsigned a = start;
    for (int k = 0; k < n; k++) a = next_addr(a, size, b);
    return a;
  endfunction

  // The lanes a transfer at address a uses on a bus of bus_bytes bytes, packed as {upper, lower}.
  // Every AHB transfer is aligned to its size, so it uses size bytes from its own lane upwards.
  function automatic logic [15:0] beat_lanes(input int unsigned a, input logic [2:0] size, input int bus_bytes);
    int lower = a % bus_bytes;
    int upper = lower + (1 << size) - 1;
    if (upper > bus_bytes - 1) upper = bus_bytes - 1;
    return {upper[7:0], lower[7:0]};
  endfunction

  // The strobe of a transfer: a 1 for every lane it uses (bit l is lane l).
  function automatic logic [63:0] beat_strb(input int unsigned a, input logic [2:0] size, input int bus_bytes);
    logic [15:0] lanes = beat_lanes(a, size, bus_bytes);
    logic [63:0] s = 0;
    for (int l = lanes[7:0]; l <= lanes[15:8]; l++) s[l] = 1'b1;
    return s;
  endfunction

  function automatic bit aligned(input int unsigned a, input logic [2:0] size);
    return (a % (1 << size)) == 0;
  endfunction

  // True when an incrementing burst of n beats (n is used only for INCR) crosses a 1 KB boundary.
  function automatic bit crosses_1k(input int unsigned start, input logic [2:0] size, input logic [2:0] b, input int n);
    int beats = beats_of(b) ? beats_of(b) : n;
    if (is_wrap(b) || beats < 2) return 0;
    return (start / 1024) != ((start + beats * (1 << size) - 1) / 1024);
  endfunction
endpackage
Read included file: ahb_mem.sv
`timescale 1ns/1ns
// ahb_mem.sv: an AHB subordinate with a byte-addressed memory behind it (read-only in this lesson).
// It registers an address phase at an edge where HSEL is 1, HTRANS is NONSEQ or SEQ and HREADY is 1,
// then runs the data phase: wait states with HREADYOUT low, a write takes HWDATA (and HWSTRB) at the
// edge that ends the data phase, a read drives HRDATA for the cycle that ends it. IDLE and BUSY get a
// zero-wait OKAY and change nothing. The switches below are plain variables: the stimulus sets them by
// name (mem.waits = 2;).
//   waits          wait states inserted in every data phase
//   waits_at[k]    wait states for the k-th transfer this memory takes (from 0; -1 = use waits)
//   err_above      transfers at or above this address get the two-cycle ERROR (and write nothing)
//   excl_on        AHB5 exclusive access: one monitor per HMASTER, HEXOKAY on success
//   trace          print every transfer the memory takes and every byte it writes
// Broken twins, each off by default:
//   ignore_hready    registers an address phase while HREADY is low (another subordinate is stretching),
//                    so it acts on a transfer the manager may still change or cancel
//   wdata_in_addr    takes HWDATA in the address phase, so a write stores the previous transfer's data
//   act_on_idle      treats IDLE and BUSY as transfers (waits, reads, writes HWDATA); this twin is an
//                    AHB-Lite design without an HWSTRB input, so it writes the lanes HSIZE selects
//   one_cycle_error  answers ERROR in one cycle (HRESP high with HREADYOUT high)
//   ignore_size      writes every lane of the bus word, whatever HSIZE and HWSTRB say
module ahb_mem #(parameter int DATA_W = 32, parameter int DEPTH = 65536) (
  input  logic              hclk,
  input  logic              hresetn,
  input  logic              hsel,
  input  logic [31:0]       haddr,
  input  logic [1:0]        htrans,
  input  logic              hwrite,
  input  logic [2:0]        hsize,
  input  logic [2:0]        hburst,
  input  logic [3:0]        hprot,
  input  logic              hmastlock,
  input  logic [DATA_W-1:0] hwdata,
  input  logic [DATA_W/8-1:0] hwstrb,
  input  logic              hexcl,
  input  logic [3:0]        hmaster,
  input  logic              hready,
  output logic              hreadyout,
  output logic              hresp,
  output logic [DATA_W-1:0] hrdata,
  output logic              hexokay
);
  import ahb_pkg::*;
  localparam int BUS = DATA_W / 8;

  // ---- switches ----
  int waits = 0;
  int waits_at [0:63];
  int unsigned err_above = 32'hffff_ffff;
  bit excl_on = 0, trace = 0;
  bit ignore_hready = 0, wdata_in_addr = 0, act_on_idle = 0, one_cycle_error = 0, ignore_size = 0;

  // ---- the memory ----
  logic [7:0] mem [0:DEPTH-1];
  int cycle = -1;
  int taken = 0;                              // transfers taken so far

  // ---- the data phase in progress ----
  bit              d_valid = 0, d_write = 0, d_err = 0, d_exok = 0, d_xfail = 0;
  int unsigned     d_addr = 0;
  logic [2:0]      d_size = 0;
  logic [1:0]      d_trans = 0;
  logic [DATA_W-1:0] d_wd = 0;                // HWDATA seen in the address phase (the wdata_in_addr twin)
  int              d_cnt = 0;                 // wait states still to insert
  bit              e_two = 0;                 // the ERROR response is in its second cycle

  // ---- exclusive monitors, one per HMASTER ----
  bit          mon_use [0:15];
  int unsigned mon_addr [0:15];
  int          mon_bytes [0:15];

  initial begin
    for (int i = 0; i < DEPTH; i++) mem[i] = 8'h00;
    for (int k = 0; k < 64; k++) waits_at[k] = -1;
    for (int m = 0; m < 16; m++) mon_use[m] = 0;
    hreadyout = 1; hresp = 0; hrdata = 0; hexokay = 0;
  end

  function automatic logic [DATA_W-1:0] read_word(input int unsigned a);
    logic [DATA_W-1:0] w = 0;
    int unsigned word = (a / BUS) * BUS;
    for (int l = 0; l < BUS; l++) w[8*l +: 8] = mem[(word + l) % DEPTH];
    return w;
  endfunction

  // Write the lanes of one transfer: the lanes its address and size select, where the strobe is 1.
  task automatic write_bytes(input int unsigned a, input logic [2:0] size, input logic [DATA_W-1:0] data, input logic [BUS-1:0] strb);
    logic [15:0] lanes = beat_lanes(a, size, BUS);
    int unsigned word = (a / BUS) * BUS;
    int lo = ignore_size ? 0 : lanes[7:0];
    int hi = ignore_size ? BUS - 1 : lanes[15:8];
    for (int l = lo; l <= hi; l++)
      if (ignore_size || act_on_idle || strb[l]) begin
        mem[(word + l) % DEPTH] = data[8*l +: 8];
        if (trace) $display("mem e%0d:   byte 0x%0h <= %02h (lane %0d)", cycle, word + l, data[8*l +: 8], l);
      end
    // any write ends the exclusive monitors that cover one of its bytes
    for (int m = 0; m < 16; m++)
      if (mon_use[m] && a < mon_addr[m] + mon_bytes[m] && mon_addr[m] < a + (1 << size)) mon_use[m] = 0;
  endtask

  always @(posedge hclk) begin
    cycle = cycle + 1;
    if (!hresetn) begin
      d_valid = 0; e_two = 0;
      hreadyout <= 1; hresp <= 0; hexokay <= 0;
    end else begin
      // 1. the data phase that ends or waits at this edge
      if (d_valid) begin
        if (hreadyout && hready) begin
          if (d_write && !d_err && !d_xfail)
            write_bytes(d_addr, d_size, wdata_in_addr ? d_wd : hwdata, hwstrb);
          d_valid = 0;
        end else if (!hreadyout) begin
          if (d_cnt > 0) d_cnt = d_cnt - 1;
          else if (d_err) e_two = 1;
        end
      end
      // 2. the address phase on the wires at this edge
      if (hsel && (htrans[1] || act_on_idle) && (hready || (ignore_hready && !d_valid))) begin
        d_valid = 1; d_addr = haddr; d_write = hwrite; d_size = hsize; d_trans = htrans; d_wd = hwdata;
        d_cnt = (taken < 64 && waits_at[taken] >= 0) ? waits_at[taken] : waits;
        taken = taken + 1;
        d_err = (haddr >= err_above); e_two = 0;
        d_exok = 0; d_xfail = 0;
        if (excl_on && hexcl && htrans[1] && !d_err) begin
          if (!hwrite) begin
            mon_use[hmaster] = 1; mon_addr[hmaster] = haddr; mon_bytes[hmaster] = 1 << hsize; d_exok = 1;
          end else if (mon_use[hmaster] && mon_addr[hmaster] == haddr && mon_bytes[hmaster] == (1 << hsize)) begin
            d_exok = 1; mon_use[hmaster] = 0;
          end else d_xfail = 1;
        end
        if (trace) $display("mem e%0d: %0s %0s 0x%0h size %0d%0s%0s%0s", cycle, trans_name(htrans), hwrite ? "write" : "read", haddr, hsize,
                            opt(!hready, " (taken while HREADY is low)"), opt(d_err, " -> ERROR"),
                            opt(d_xfail, " -> exclusive failed"));
      end
      // 3. the response for the cycle that starts now
      if (d_valid && d_cnt > 0) begin
        hreadyout <= 0; hresp <= 0; hexokay <= 0;
      end else if (d_valid && d_err) begin
        hreadyout <= one_cycle_error ? 1'b1 : e_two; hresp <= 1; hexokay <= 0;
      end else begin
        hreadyout <= 1; hresp <= 0; hexokay <= d_valid && d_exok;
      end
      if (d_valid && !d_write) hrdata <= d_err ? '0 : read_word(d_addr);
    end
  end
endmodule
Read included file: ahb_checker.sv
`timescale 1ns/1ns
// ahb_checker.sv: the rules of an AHB interface, checked at every rising edge (read-only).
// Each broken rule is named with the edge where it was seen:
//   reset         HTRANS is not IDLE, or HREADY is low, while reset is active;
//   hold          the address or control changed during a wait state (HREADY low), outside the
//                 changes the protocol allows;
//   trans_change  HTRANS changed during a wait state other than IDLE to NONSEQ, BUSY to SEQ (fixed
//                 bursts) or BUSY to anything (INCR); or SEQ/BUSY with no burst in progress;
//   seq_addr      a SEQ or BUSY address that is not the previous beat's address plus the size
//                 (wrapped for a WRAP burst);
//   burst_ctrl    HSIZE, HBURST, HWRITE or HPROT changed inside a burst;
//   align         a transfer not aligned to its size;
//   size_bus      a transfer wider than the data bus;
//   kb1           an incrementing burst that crosses a 1 KB boundary;
//   burst_len     a fixed-length burst that ends early or runs long, BUSY after a SINGLE, or BUSY
//                 after the last beat of a fixed-length burst;
//   idle_okay     an IDLE or BUSY transfer that did not get a zero-wait OKAY;
//   err_shape     an ERROR that is not two cycles (HREADY low then high, HRESP high in both);
//   exokay        HEXOKAY with HREADY low, with an ERROR, or for a transfer that was not exclusive;
//   known         x on the address, control, or the active lanes of the data.
// A NOTE (not a broken rule) marks a transfer kept after the first cycle of an ERROR: the protocol
// allows it, most managers cancel.
module ahb_checker #(parameter int DATA_W = 32) (
  input logic              hclk,
  input logic              hresetn,
  input logic [31:0]       haddr,
  input logic [1:0]        htrans,
  input logic              hwrite,
  input logic [2:0]        hsize,
  input logic [2:0]        hburst,
  input logic [3:0]        hprot,
  input logic              hmastlock,
  input logic [DATA_W-1:0] hwdata,
  input logic              hexcl,
  input logic              hready,
  input logic              hresp,
  input logic [DATA_W-1:0] hrdata,
  input logic              hexokay
);
  import ahb_pkg::*;
  localparam int BUS = DATA_W / 8;
  int cycle = -1, transfers = 0, waits = 0, errors = 0, broken = 0, notes = 0;

  function void report(input string rule, input string what);
    broken++;
    $display("RULE %s broken at edge %0d: %s", rule, cycle, what);
  endfunction

  function automatic logic [DATA_W-1:0] lane_mask(input int unsigned a, input logic [2:0] size);
    logic [15:0] lanes = beat_lanes(a, size, BUS);
    logic [DATA_W-1:0] m = '0;
    for (int l = lanes[7:0]; l <= lanes[15:8]; l++) m[8*l +: 8] = 8'hff;
    return m;
  endfunction

  // The previous edge.
  bit          p_on = 0;
  logic        p_ready = 1, p_resp = 0, p_write = 0, p_lock = 0;
  logic [1:0]  p_trans = 0;
  logic [31:0] p_addr = 0;
  logic [2:0]  p_size = 0, p_burst = 0;
  logic [3:0]  p_prot = 0;
  bit          e_first = 0;           // the previous edge was the first cycle of an ERROR
  // The data phase in progress.
  bit          d_on = 0, d_idle = 0, d_write = 0, d_excl = 0;
  int unsigned d_addr = 0;
  logic [2:0]  d_size = 0;
  // The burst in progress.
  bit          b_on = 0, b_err = 0, b_write = 0, b_kb = 0;
  logic [2:0]  b_burst = 0, b_size = 0;
  logic [3:0]  b_prot = 0;
  int unsigned b_first = 0, b_last = 0;
  int          b_count = 0;
  int unsigned exp_a;

  task automatic end_burst();
    if (b_on && beats_of(b_burst) > 1 && b_count < beats_of(b_burst) && !b_err)
      report("burst_len", $sformatf("%0s burst at 0x%0h ended after %0d of %0d beats", burst_name(b_burst), b_first, b_count, beats_of(b_burst)));
    b_on = 0;
  endtask

  task automatic check_beat();
    if ((1 << hsize) > BUS) report("size_bus", $sformatf("a %0d-byte transfer on a %0d-byte bus", 1 << hsize, BUS));
    if (!aligned(haddr, hsize)) report("align", $sformatf("a %0d-byte transfer at 0x%0h is not aligned to its size", 1 << hsize, haddr));
  endtask

  task automatic check_ctrl(input string what);
    if (hsize !== b_size || hburst !== b_burst || hwrite !== b_write || hprot !== b_prot)
      report("burst_ctrl", $sformatf("%0s at 0x%0h changed HSIZE, HBURST, HWRITE or HPROT inside the burst", what, haddr));
  endtask

  always @(posedge hclk) begin
    cycle++;
    if (!hresetn) begin
      if (htrans !== IDLE) report("reset", "HTRANS is not IDLE during reset");
      if (hready !== 1) report("reset", "HREADY is low during reset");
      p_on = 0; d_on = 0; b_on = 0; e_first = 0;
    end else begin
      // ---- the data phase that ends or waits at this edge ----
      if (hready === 0) waits++;
      if (e_first) begin
        if (hresp !== 1 || hready !== 1) report("err_shape", "the second cycle of an ERROR must have HRESP high and HREADY high");
      end else if (hresp === 1 && hready === 1)
        report("err_shape", "ERROR with HREADY high in its first cycle: an ERROR takes two cycles");
      if (hresp === 1 && b_on) b_err = 1;
      if (d_on && d_idle) begin
        if (hready !== 1 || hresp !== 0) report("idle_okay", "an IDLE or BUSY transfer must get a zero-wait OKAY");
        d_on = 0;
      end
      if (hexokay === 1) begin
        if (hready !== 1) report("exokay", "HEXOKAY while HREADY is low");
        else if (hresp === 1) report("exokay", "HEXOKAY together with an ERROR");
        else if (!(d_on && d_excl)) report("exokay", "HEXOKAY for a transfer that was not exclusive");
      end
      if (hready === 1 && d_on && !d_idle) begin
        if (d_write && $isunknown(hwdata & lane_mask(d_addr, d_size))) report("known", "HWDATA is x on an active lane");
        if (!d_write && hresp === 0 && $isunknown(hrdata & lane_mask(d_addr, d_size))) report("known", "HRDATA is x on an active lane");
        transfers++;
        if (hresp === 1) errors++;
        d_on = 0;
      end
      if (e_first && hready === 1 && (htrans === NONSEQ || htrans === SEQ)) begin
        notes++;
        $display("NOTE cancel at edge %0d: the %0s at 0x%0h behind an ERROR was kept, not cancelled (allowed; most managers cancel)", cycle, trans_name(htrans), haddr);
      end
      // ---- the address phase on the wires at this edge ----
      if (htrans !== IDLE && ($isunknown(haddr) || $isunknown(hwrite) || $isunknown(hsize) || $isunknown(hburst)))
        report("known", "address or control is x while HTRANS is not IDLE");
      if ($isunknown(htrans)) report("known", "HTRANS is x");
      if (p_on && p_ready === 0 && !e_first) begin
        // a wait state at the previous edge: only the allowed changes
        if (p_trans == IDLE) begin
          if (htrans === BUSY || htrans === SEQ) report("trans_change", $sformatf("IDLE changed to %0s during a wait state (only NONSEQ may follow)", trans_name(htrans)));
        end else if (p_trans == BUSY) begin
          if (p_burst != INCR) begin
            if (htrans !== BUSY && htrans !== SEQ) report("trans_change", $sformatf("BUSY in a %0s burst changed to %0s during a wait state (only SEQ may follow)", burst_name(p_burst), trans_name(htrans)));
            else if (haddr !== p_addr) report("hold", $sformatf("HADDR changed from 0x%0h to 0x%0h during a wait state", p_addr, haddr));
          end
        end else begin
          if (htrans !== p_trans) report("trans_change", $sformatf("%0s changed to %0s during a wait state", trans_name(p_trans), trans_name(htrans)));
          else if (haddr !== p_addr) report("hold", $sformatf("HADDR changed from 0x%0h to 0x%0h during a wait state", p_addr, haddr));
          else if (hwrite !== p_write || hsize !== p_size || hburst !== p_burst || hprot !== p_prot || hmastlock !== p_lock)
            report("hold", "HWRITE, HSIZE, HBURST, HPROT or HMASTLOCK changed during a wait state");
        end
      end
      if (hready === 1) begin
        // the address phase is accepted at this edge
        if (htrans === IDLE) begin
          end_burst();
          d_on = 1; d_idle = 1;
        end else if (htrans === NONSEQ) begin
          end_burst();
          check_beat();
          b_on = 1; b_err = 0; b_kb = 0; b_first = haddr; b_last = haddr; b_count = 1;
          b_burst = hburst; b_size = hsize; b_write = hwrite; b_prot = hprot;
          d_on = 1; d_idle = 0; d_write = hwrite; d_addr = haddr; d_size = hsize; d_excl = hexcl;
        end else if (htrans === SEQ) begin
          if (!b_on) report("trans_change", $sformatf("SEQ at 0x%0h with no burst in progress", haddr));
          else begin
            exp_a = next_addr(b_last, b_size, b_burst);
            if (haddr !== exp_a) report("seq_addr", $sformatf("SEQ at 0x%0h; the beat after 0x%0h in a %0s burst of %0d-byte transfers is 0x%0h", haddr, b_last, burst_name(b_burst), 1 << b_size, exp_a));
            check_ctrl("SEQ");
            if (!is_wrap(b_burst) && !b_kb && (haddr / 1024) != (b_first / 1024)) begin
              b_kb = 1;
              report("kb1", $sformatf("SEQ at 0x%0h crosses the 1 KB boundary of the burst that started at 0x%0h", haddr, b_first));
            end
            b_count++;
            if (beats_of(b_burst) > 0 && b_count > beats_of(b_burst))
              report("burst_len", $sformatf("beat %0d of a %0s burst, which has %0d beats", b_count, burst_name(b_burst), beats_of(b_burst)));
            b_last = haddr;
          end
          check_beat();
          d_on = 1; d_idle = 0; d_write = hwrite; d_addr = haddr; d_size = hsize; d_excl = hexcl;
        end else if (htrans === BUSY) begin
          if (!b_on) report("trans_change", $sformatf("BUSY at 0x%0h with no burst in progress", haddr));
          else if (b_burst == SINGLE) report("burst_len", "BUSY after a SINGLE transfer");
          else begin
            exp_a = next_addr(b_last, b_size, b_burst);
            if (beats_of(b_burst) > 1 && b_count == beats_of(b_burst))
              report("burst_len", $sformatf("BUSY after the last beat of the %0s burst (a fixed-length burst ends with SEQ)", burst_name(b_burst)));
            else if (haddr !== exp_a) report("seq_addr", $sformatf("BUSY at 0x%0h must show the next beat's address 0x%0h", haddr, exp_a));
            check_ctrl("BUSY");
          end
          d_on = 1; d_idle = 1;
        end
      end
      e_first = (hresp === 1 && hready === 0);
    end
    p_on = hresetn; p_ready = hready; p_resp = hresp; p_trans = htrans; p_addr = haddr; p_write = hwrite;
    p_size = hsize; p_burst = hburst; p_prot = hprot; p_lock = hmastlock;
  end
  final $display("checker: %0d transfers, %0d wait edges, %0d errors, %0d rules broken", transfers, waits, errors, broken);
endmodule
Read included file: ahb_tasks.svh
// ahb_tasks.svh: the manager side of the bench, as tasks for the stimulus (read-only).
// ahb_write, ahb_read and ahb_burst queue transfers; go() puts the queue on the bus and returns when
// the last data phase has ended. The driver below issues the next address phase at the same edge where
// the previous one is accepted, so the address of transfer N+1 is on the wires during the data phase
// of transfer N. Write data for a burst goes in wd[0], wd[1], ... (one entry per beat, the lowest byte
// at the lowest address); the data of every read comes back in rd[0], rd[1], ... in issue order, with
// the responses in rr[].
// The beat log has one line per accepted address phase (A), per ended data phase (D) and per transfer
// the manager cancels (X), each with the edge where it happened; watch = 1 adds one line per edge.
int cycle = -1;
always @(posedge hclk) cycle = cycle + 1;

localparam int QN = 512;
int unsigned q_addr [0:QN-1];
logic        q_write [0:QN-1];
logic [2:0]  q_size [0:QN-1];
logic [2:0]  q_burst [0:QN-1];
logic [1:0]  q_trans [0:QN-1];
logic [63:0] q_data [0:QN-1];
logic        q_lock [0:QN-1], q_excl [0:QN-1], q_sforce [0:QN-1];
logic [3:0]  q_prot [0:QN-1], q_master [0:QN-1];
logic [2:0]  q_pext [0:QN-1];                 // AHB5: HPROT[6:4] (with AHB5_PROT defined)
logic        q_nsec [0:QN-1];                 // AHB5: HNONSEC (with AHB5_PROT defined)
logic [7:0]  q_strb [0:QN-1];
int          q_bn [0:QN-1], q_beat [0:QN-1], q_state [0:QN-1];   // burst number, beat, 0 queued 1 done 2 cancelled
logic [63:0] q_rdata [0:QN-1];
logic        q_resp [0:QN-1], q_exok [0:QN-1];
int q_n = 0, q_next = 0, bn = 0, last_start = 0, last_bn = 0;

logic [63:0] wd [0:255];
logic [63:0] rd [0:255];
logic        rr [0:255];
int          n_rd = 0;
logic        last_resp = 0, last_exokay = 0;
// quiet = 1 silences the beat log; watch = 1 prints the bus at every edge.
bit quiet = 0, watch = 0, running = 0, drv_done = 0;
// Driver switches (broken twins, off by default):
//   move_in_wait  the address moves on by one transfer size during a wait state
//   no_cancel     the transfer behind an ERROR is not cancelled (allowed, but the checker notes it)
// After the first cycle of an ERROR the driver cancels the transfer already in its address phase: the
// rest of the same burst is dropped; a separate transfer is issued again afterwards (reissue = 0 drops it).
//   busy_end      a BUSY after the last beat of every fixed-length burst
//   cross_1k      incrementing bursts are issued across a 1 KB boundary instead of being split
//   unaligned     transfers not aligned to their size are issued instead of refused
//   wrap_bug      a WRAP8 burst's addresses wrap inside 16 bytes, as if it were WRAP4
bit reissue = 1;
bit move_in_wait = 0, no_cancel = 0, busy_end = 0, cross_1k = 0, unaligned = 0, wrap_bug = 0;
// Attributes of the transfers queued next.
logic       lock = 0, excl = 0;
logic [3:0] prot = 4'b0011, master = 0;
// AHB5 (IHI 0033C 3.9, 3.10), used only by a bench built with ahb5: HPROT[6:4] and HNONSEC.
logic [2:0] prot_ext = 0;
logic       nonsec = 0;
bit         strb_force = 0;
logic [7:0] strb_val = 8'hff;
// What the bus is carrying in the data phase, for the waveform scenes: the address and lanes of the beat.
int unsigned beat_a = 0;
logic [7:0]  beat_m = 0;

function automatic int unsigned m_next(input int unsigned a, input logic [2:0] size, input logic [2:0] b);
  if (wrap_bug && b == WRAP8) return next_addr(a, size, WRAP4);
  return next_addr(a, size, b);
endfunction

task automatic q_push(input int unsigned a, input logic w, input logic [2:0] size, input logic [2:0] b, input logic [1:0] t,
                      input logic [63:0] data, input int burst_no, input int beat);
  q_addr[q_n] = a; q_write[q_n] = w; q_size[q_n] = size; q_burst[q_n] = b; q_trans[q_n] = t; q_data[q_n] = data;
  q_lock[q_n] = lock; q_excl[q_n] = excl; q_prot[q_n] = prot; q_master[q_n] = master;
  q_pext[q_n] = prot_ext; q_nsec[q_n] = nonsec;
  q_sforce[q_n] = strb_force; q_strb[q_n] = strb_val;
  q_bn[q_n] = burst_no; q_beat[q_n] = beat; q_state[q_n] = 0; q_resp[q_n] = 0; q_exok[q_n] = 0; q_rdata[q_n] = 0;
  q_n = q_n + 1;
endtask

task automatic q_copy(input int dst, input int src);
  q_addr[dst] = q_addr[src]; q_write[dst] = q_write[src]; q_size[dst] = q_size[src]; q_burst[dst] = q_burst[src];
  q_trans[dst] = q_trans[src]; q_data[dst] = q_data[src]; q_lock[dst] = q_lock[src]; q_excl[dst] = q_excl[src];
  q_prot[dst] = q_prot[src]; q_master[dst] = q_master[src]; q_sforce[dst] = q_sforce[src]; q_strb[dst] = q_strb[src];
  q_pext[dst] = q_pext[src]; q_nsec[dst] = q_nsec[src];
  q_bn[dst] = q_bn[src]; q_beat[dst] = q_beat[src]; q_state[dst] = q_state[src];
endtask

// One write of size bytes (0 = byte, 1 = halfword, 2 = word) at addr; data holds the bytes, lowest first.
task automatic ahb_write(input int unsigned addr, input logic [2:0] size, input logic [63:0] data);
  if (!unaligned && !aligned(addr, size))
    $display("refused: a %0d-byte transfer at 0x%0h is not aligned (every AHB transfer is aligned to its size)", 1 << size, addr);
  else begin
    bn = bn + 1; last_start = q_n; last_bn = bn;
    q_push(addr, 1, size, SINGLE, NONSEQ, data, bn, 0);
  end
endtask

// One read of size bytes at addr; the bytes come back in rd[] in issue order.
task automatic ahb_read(input int unsigned addr, input logic [2:0] size);
  if (!unaligned && !aligned(addr, size))
    $display("refused: a %0d-byte transfer at 0x%0h is not aligned (every AHB transfer is aligned to its size)", 1 << size, addr);
  else begin
    bn = bn + 1; last_start = q_n; last_bn = bn;
    q_push(addr, 0, size, SINGLE, NONSEQ, 0, bn, 0);
  end
endtask

// A burst: hburst SINGLE, INCR (beats gives its length), WRAP4, INCR4, ... INCR16. Write data from wd[].
// An incrementing burst that would cross a 1 KB boundary is issued as two INCR bursts split at the
// boundary (unless cross_1k is set).
task automatic ahb_burst(input logic w, input logic [2:0] hb, input int unsigned addr, input logic [2:0] size, input int beats = 0);
  int n;
  int unsigned a;
  logic [2:0] b;
  logic [1:0] t;
  bit split;
  n = beats_of(hb) ? beats_of(hb) : (beats > 0 ? beats : 1);
  a = addr; b = hb; split = 0;
  if (!unaligned && !aligned(addr, size))
    $display("refused: a %0d-byte burst at 0x%0h is not aligned (every AHB transfer is aligned to its size)", 1 << size, addr);
  else begin
    if (!cross_1k && crosses_1k(addr, size, hb, n)) begin
      split = 1; b = INCR;
      $display("note: %0s at 0x%0h would cross a 1 KB boundary; issued as INCR bursts split at the boundary", burst_name(hb), addr);
    end
    bn = bn + 1; last_start = q_n; last_bn = bn;
    for (int k = 0; k < n; k++) begin
      t = (k == 0) ? NONSEQ : SEQ;
      if (k > 0 && split && (a % 1024) == 0) begin t = NONSEQ; bn = bn + 1; end
      q_push(a, w, size, b, t, w ? wd[k] : 64'h0, bn, k);
      a = m_next(a, size, b);
    end
    if (busy_end && beats_of(b) > 1) q_push(a, w, size, b, BUSY, 64'h0, bn, n);
  end
endtask

// n BUSY cycles before beat k of the burst queued last (k = its length: after the last beat).
task automatic busy_at(input int k, input int n = 1);
  int idx, src;
  idx = q_n;
  for (int j = q_n - 1; j >= last_start; j--)
    if (q_trans[j][1] && q_beat[j] == k) idx = j;
  src = (idx < q_n) ? idx : q_n - 1;           // the beat the BUSY announces, or the last beat
  for (int j = q_n - 1; j >= idx; j--) q_copy(j + n, j);
  for (int j = 0; j < n; j++) begin
    q_copy(idx + j, src >= idx ? src + n : src);
    q_trans[idx + j] = BUSY; q_data[idx + j] = 0; q_beat[idx + j] = k;
    if (src < idx) q_addr[idx + j] = m_next(q_addr[src], q_size[src], q_burst[src]);
  end
  q_n = q_n + n;
endtask

// n IDLE cycles in the queue (the address and control keep their last values).
task automatic idle_q(input int n);
  for (int j = 0; j < n; j++)
    if (q_n > 0) q_push(q_addr[q_n - 1], q_write[q_n - 1], q_size[q_n - 1], q_burst[q_n - 1], IDLE, 64'h0, 0, 0);
    else q_push(0, 0, 0, SINGLE, IDLE, 64'h0, 0, 0);
endtask

// The driver: pick, hold, cancel.
int a_idx = -1, d_idx = -1;       // queue entries in the address phase and in the data phase (-1: none)
bit moved = 0;
logic        s_ready, s_resp, s_exok, s_write;
logic [DATA_W-1:0] s_rdata;
logic [31:0] s_addr;
logic [1:0]  s_trans;
logic [2:0]  s_size, s_burst;
int          s_done, s_acc, s_cfrom, s_cto, s_cmode;

task automatic complete(input int i);
  logic [15:0] lanes;
  logic [63:0] bytes;
  q_state[i] = 1; q_resp[i] = s_resp; q_exok[i] = s_exok; last_resp = s_resp; last_exokay = s_exok;
  if (!q_write[i]) begin
    lanes = beat_lanes(q_addr[i], q_size[i], BUS_BYTES);
    bytes = (s_rdata >> (8 * lanes[7:0])) & ((64'h1 << (8 * (lanes[15:8] - lanes[7:0] + 1))) - 1);
    q_rdata[i] = bytes; rd[n_rd] = bytes; rr[n_rd] = s_resp; n_rd = n_rd + 1;
  end
  if (!quiet) $display("e%0d D  %0s addr=0x%0h data=0x%0h %0s%0s", cycle, q_write[i] ? "write" : "read ", q_addr[i],
                       q_write[i] ? q_data[i] : q_rdata[i], resp_name(s_resp),
                       opt(q_excl[i], s_exok ? " EXOKAY" : " (HEXOKAY low: exclusive failed)"));
endtask

task automatic drive();
  logic [15:0] lanes;
  logic [63:0] s;
  int e;
  if (a_idx >= 0) begin
    e = a_idx;
    htrans = q_trans[e]; haddr = q_addr[e] + (moved ? (1 << q_size[e]) : 0); hwrite = q_write[e]; hsize = q_size[e];
    hburst = q_burst[e]; hprot = q_prot[e]; hmastlock = q_lock[e]; hexcl = q_excl[e]; hmaster = q_master[e];
`ifdef AHB5_PROT
    hprot_ext = q_pext[e]; hnonsec = q_nsec[e];
`endif
  end else begin
    htrans = IDLE; hmastlock = 0; hexcl = 0;      // address and control keep their last values
  end
  if (d_idx >= 0 && q_write[d_idx]) begin
    lanes = beat_lanes(q_addr[d_idx], q_size[d_idx], BUS_BYTES);
    s = beat_strb(q_addr[d_idx], q_size[d_idx], BUS_BYTES);
    hwdata = q_data[d_idx] << (8 * lanes[7:0]);
    hwstrb = q_sforce[d_idx] ? q_strb[d_idx][BUS_BYTES-1:0] : s[BUS_BYTES-1:0];
    beat_a = q_addr[d_idx]; beat_m = hwstrb;
  end else begin
    hwdata = '0; hwstrb = '0; beat_m = 0;
  end
endtask

always @(posedge hclk) begin
  s_ready = hready; s_resp = hresp; s_exok = hexokay; s_rdata = hrdata; s_addr = haddr; s_trans = htrans;
  s_write = hwrite; s_size = hsize; s_burst = hburst;
  s_done = -1; s_acc = -1; s_cmode = 0;
  if (hresetn) begin
    if (s_ready === 1'b1) begin
      s_done = d_idx; d_idx = -1;
      if (a_idx >= 0 && moved) q_addr[a_idx] = s_addr;   // the address the subordinate took
      if (a_idx >= 0 && q_trans[a_idx] != IDLE) s_acc = a_idx;
      if (a_idx >= 0 && q_trans[a_idx][1]) d_idx = a_idx;
      a_idx = -1; moved = 0;
      if (running && q_next < q_n) begin a_idx = q_next; q_next = q_next + 1; end
    end else if (s_resp === 1'b1 && !no_cancel && a_idx >= 0 && q_trans[a_idx] != IDLE) begin
      // the first cycle of an ERROR: the transfer already on the wires is cancelled (IHI 0033C 5.1.3)
      s_cfrom = a_idx;
      if (d_idx >= 0 && q_bn[a_idx] == q_bn[d_idx]) begin
        s_cto = a_idx;
        while (s_cto < q_n && q_bn[s_cto] == q_bn[d_idx]) begin q_state[s_cto] = 2; s_cto = s_cto + 1; end
        q_next = s_cto; s_cmode = 1;               // the rest of the burst is dropped
      end else if (reissue) begin
        q_next = a_idx; s_cmode = 2;               // a separate transfer: issued again after the ERROR
      end else begin
        q_state[a_idx] = 2; s_cto = a_idx + 1; s_cmode = 3;   // a separate transfer, dropped
      end
      a_idx = -1;
    end else if (move_in_wait && a_idx >= 0 && q_trans[a_idx][1]) moved = 1;
  end
  #1;
  if (s_done >= 0) complete(s_done);
  if (s_acc >= 0 && !quiet)
    $display("e%0d A  %0s %0s addr=0x%0h size=%0d %0s%0s%0s", cycle, trans_name(s_trans), s_write ? "WRITE" : "READ", s_addr, s_size,
             burst_name(s_burst), opt(q_lock[s_acc], " locked"), opt(q_excl[s_acc], " exclusive"));
  if (s_cmode == 1 && !quiet)
    for (int j = s_cfrom; j < s_cto; j++)
      if (q_trans[j][1]) $display("e%0d X  cancelled %0s %0s addr=0x%0h (the rest of the burst is dropped)", cycle, trans_name(q_trans[j]), q_write[j] ? "WRITE" : "READ", q_addr[j]);
  if (s_cmode == 3 && !quiet)
    $display("e%0d X  cancelled %0s %0s addr=0x%0h", cycle, trans_name(q_trans[s_cfrom]), q_write[s_cfrom] ? "WRITE" : "READ", q_addr[s_cfrom]);
  if (s_cmode == 2 && !quiet)
    $display("e%0d X  withdrew %0s %0s addr=0x%0h (issued again after the ERROR)", cycle, trans_name(q_trans[s_cfrom]), q_write[s_cfrom] ? "WRITE" : "READ", q_addr[s_cfrom]);
  drive();
  drv_done = running && q_next >= q_n && a_idx < 0 && d_idx < 0;   // go() returns after this edge's log
end

// A text waveform for the lesson's trace blocks: with watch = 1, one line per rising edge with the
// values sampled at that edge (cycle k of a trace is what edge k sees).
int wave_edge = -1;
always @(posedge hclk) begin
  wave_edge = wave_edge + 1;
  if (watch) $display("wave e%0d: htrans=%0s haddr=%h hwrite=%b hsize=%0d hburst=%0s hwdata=%h hready=%b hresp=%b hrdata=%h",
                      wave_edge, trans_name(htrans), haddr, hwrite, hsize, burst_name(hburst), hwdata, hready, hresp, hrdata);
end

// Put the queue on the bus and wait until every transfer in it has ended; then empty the queue.
task automatic go();
  n_rd = 0; drv_done = 0; running = 1;
  wait (drv_done);
  running = 0; drv_done = 0; q_n = 0; q_next = 0;
endtask

// The table of a burst before it runs: the address, lanes and strobe of every beat.
task automatic beat_table(input int unsigned addr, input logic [2:0] size, input logic [2:0] hb, input int beats = 0);
  int n;
  int unsigned a, window, base;
  logic [15:0] lanes;
  logic [63:0] s;
  n = beats_of(hb) ? beats_of(hb) : (beats > 0 ? beats : 1);
  a = addr;
  $display("%0s at 0x%0h: %0d beat%0s of %0d byte%0s, bus %0d bytes", burst_name(hb), addr, n, opt(n > 1, "s"), 1 << size, opt(size != 0, "s"), BUS_BYTES);
  if (is_wrap(hb)) begin
    window = (1 << size) * beats_of(hb); base = (addr / window) * window;
    $display("  wraps inside 0x%0h-0x%0h (%0d beats x %0d bytes)", base, base + window - 1, beats_of(hb), 1 << size);
  end
  $display("  beat  address  lanes  strobe");
  for (int k = 0; k < n; k++) begin
    lanes = beat_lanes(a, size, BUS_BYTES);
    s = beat_strb(a, size, BUS_BYTES);
    $display("  %4d  0x%05h  %0d-%0d    %b", k, a[19:0], lanes[7:0], lanes[15:8], s[BUS_BYTES-1:0]);
    a = m_next(a, size, hb);
  end
  if (crosses_1k(addr, size, hb, n)) $display("  this burst crosses a 1 KB boundary");
  if (!aligned(addr, size)) $display("  0x%0h is not aligned to %0d bytes: AHB does not allow it", addr, 1 << size);
endtask

// One byte of the memory that owns an address (the fabric's second memory from 0x1000).
function automatic logic [7:0] mem_byte(input int unsigned a);
`ifdef AHB_MEM1
  if (a >= 32'h1000 && a < 32'h2000) return `AHB_MEM1.mem[a % `AHB_DEPTH];
  if (a >= 32'h1000) return 8'h00;
`endif
  return `AHB_MEM.mem[a % `AHB_DEPTH];
endfunction
task automatic set_byte(input int unsigned a, input logic [7:0] v);
`ifdef AHB_MEM1
  if (a >= 32'h1000 && a < 32'h2000) `AHB_MEM1.mem[a % `AHB_DEPTH] = v;
  else if (a < 32'h1000) `AHB_MEM.mem[a % `AHB_DEPTH] = v;
`else
  `AHB_MEM.mem[a % `AHB_DEPTH] = v;
`endif
endtask

// The memory, n bytes from addr, one bus word per group.
task automatic dump(input int unsigned addr, input int n);
  string line;
  int unsigned a = (addr / 16) * 16;
  while (a < addr + n) begin
    line = $sformatf("0x%05h ", a[19:0]);
    for (int i = 0; i < 16; i++) begin
      if (i % BUS_BYTES == 0) line = {line, " "};
      line = {line, $sformatf(" %02h", mem_byte(a + i))};
    end
    $display("%s", line);
    a = a + 16;
  end
endtask

// Fill n bytes from addr with first, first+1, ... so untouched bytes stay recognisable.
task automatic mem_fill(input int unsigned addr, input int n, input logic [7:0] first = 8'h00);
  for (int i = 0; i < n; i++) set_byte(addr + i, first + i[7:0]);
endtask

// Drive nothing new for n cycles.
task automatic idle(input int n);
  repeat (n) @(posedge hclk);
  #1;
endtask
Read included file: ahb5_attr_mon.sv
`timescale 1ns/1ns
// ahb5_attr_mon.sv: prints one line per accepted address phase (read-only).
// HPROT[6:2] gives the memory type by Table 3-7; a combination that table does not list is "not
// permitted". HNONSEC = 1 is Non-secure. HPROT[1] is privileged, HPROT[0] = 1 is a data access.
// It also reports an HNONSEC that changes inside a burst (it must be constant, 3.10).
module ahb5_attr_mon (
  input logic        hclk,
  input logic        hresetn,
  input logic [1:0]  htrans,
  input logic        hready,
  input logic        hwrite,
  input logic [31:0] haddr,
  input logic [6:0]  hprot,
  input logic        hnonsec);
  int cycle = -1, not_permitted = 0;   // not_permitted counts transfers whose HPROT Table 3-7 does not list
  logic b_nonsec = 0;
  string t;
  function automatic string mtype(input logic [6:2] p);
    case (p)
      5'b00000: return "Device-nE";
      5'b00001: return "Device-E";
      5'b00010: return "Normal Non-cacheable Non-shareable";
      5'b00110, 5'b01110: return "Write-through Non-shareable";
      5'b00111, 5'b01111: return "Write-back Non-shareable";
      5'b10010: return "Normal Non-cacheable Shareable";
      5'b10110, 5'b11110: return "Write-through Shareable";
      5'b10111, 5'b11111: return "Write-back Shareable";
      default: return "not permitted (Table 3-7)";
    endcase
  endfunction
  always @(posedge hclk) begin
    cycle = cycle + 1;
    if (hresetn && hready && htrans[1]) begin
      if (htrans == 2'b11 && hnonsec !== b_nonsec) $display("attr e%0d: HNONSEC changed inside a burst", cycle);
      if (htrans == 2'b10) b_nonsec = hnonsec;
      t = mtype(hprot[6:2]);
      if (t == "not permitted (Table 3-7)") not_permitted++;
      $display("attr e%0d: %0s 0x%0h %0s%0s, %0s, %0s, %0s", cycle, hwrite ? "write" : "read", haddr, t,
               (hprot[5] && hprot[4]) ? " allocate" : "", hnonsec ? "Non-secure" : "Secure",
               hprot[1] ? "privileged" : "unprivileged", hprot[0] ? "data" : "instruction");
    end
  end
endmodule

Check Yourself

Predict the outputOne read with HPROT[3:0] = 1110, HPROT[6:4] = 011 and HNONSEC = 1. What line does the monitor print?
`timescale 1ns/1ps
`define AHB5_PROT
module tb;
  import ahb_pkg::*;
  localparam int DATA_W = 32, BUS_BYTES = DATA_W / 8;
  logic hclk = 0, hresetn = 0;
  always #5 hclk = ~hclk;                 // rising edges at 5, 15, 25, ...
  logic [31:0]       haddr = 0;
  logic [1:0]        htrans = 0;
  logic              hwrite = 0, hmastlock = 0, hexcl = 0;
  logic [2:0]        hsize = 0, hburst = 0;
  logic [3:0]        hprot = 4'b0011, hmaster = 0;
  logic [DATA_W-1:0] hwdata = 0;
  logic [DATA_W/8-1:0] hwstrb = 0;
  logic [DATA_W-1:0] hrdata;
  logic              hready, hresp, hexokay;
  logic [2:0]        hprot_ext = 0;             // AHB5: HPROT[6:4]
  logic              hnonsec = 0;               // AHB5: HNONSEC
  wire  [6:0]        hprot7 = {hprot_ext, hprot};
  logic hreadyout;
  ahb_mem #(.DATA_W(DATA_W)) mem (.hclk(hclk), .hresetn(hresetn), .hsel(1'b1), .haddr(haddr), .htrans(htrans), .hwrite(hwrite), .hsize(hsize), .hburst(hburst), .hprot(hprot), .hmastlock(hmastlock), .hwdata(hwdata), .hwstrb(hwstrb), .hexcl(hexcl), .hmaster(hmaster), .hready(hready),
    .hreadyout(hreadyout), .hresp(hresp), .hrdata(hrdata), .hexokay(hexokay));
  assign hready = hreadyout;              // one subordinate: its HREADYOUT is the bus HREADY
  `define AHB_MEM mem
  `define AHB_DEPTH 65536
  `include "ahb_tasks.svh"
  ahb5_attr_mon mon (.hclk(hclk), .hresetn(hresetn), .htrans(htrans), .hready(hready), .hwrite(hwrite), .haddr(haddr), .hprot(hprot7), .hnonsec(hnonsec));
  initial begin

    repeat (2) @(posedge hclk); #1 hresetn = 1;   // reset released after edge 1
    @(posedge hclk); #1;                          // the first transfer may start after edge 2
    quiet = 1;
    nonsec = 1; prot = 4'b1110; prot_ext = 3'b011;   ahb_read(32'h200, 2);
    go();
    repeat (3) @(posedge hclk);
    $finish;
  end
endmodule
Read included file: ahb_pkg.sv
`timescale 1ns/1ns
// ahb_pkg.sv: the encodings and the arithmetic of a burst (read-only).
// The memory, the driver, the checker and the lesson text all use these functions, so they never
// disagree about the address of a beat or the lanes it uses.
package ahb_pkg;
  localparam logic [1:0] IDLE = 2'b00, BUSY = 2'b01, NONSEQ = 2'b10, SEQ = 2'b11;
  localparam logic [2:0] SINGLE = 3'b000, INCR = 3'b001, WRAP4 = 3'b010, INCR4 = 3'b011,
                         WRAP8 = 3'b100, INCR8 = 3'b101, WRAP16 = 3'b110, INCR16 = 3'b111;
  localparam logic OKAY = 1'b0, ERROR = 1'b1;

  function automatic string trans_name(input logic [1:0] t);
    case (t) IDLE: return "IDLE"; BUSY: return "BUSY"; NONSEQ: return "NONSEQ"; default: return "SEQ"; endcase
  endfunction
  function automatic string burst_name(input logic [2:0] b);
    case (b)
      SINGLE: return "SINGLE"; INCR: return "INCR"; WRAP4: return "WRAP4"; INCR4: return "INCR4";
      WRAP8: return "WRAP8"; INCR8: return "INCR8"; WRAP16: return "WRAP16"; default: return "INCR16";
    endcase
  endfunction
  function automatic string resp_name(input logic r);
    return r ? "ERROR" : "OKAY";
  endfunction
  // s when c is 1, else the empty string (a string-typed result prints the same on every simulator).
  function automatic string opt(input bit c, input string s);
    if (c) return s;
    return "";
  endfunction

  // Beats in a burst: 1 for SINGLE, 4, 8 or 16 for the fixed bursts, 0 for INCR (undefined length).
  function automatic int beats_of(input logic [2:0] b);
    case (b) SINGLE: return 1; INCR: return 0; WRAP4, INCR4: return 4; WRAP8, INCR8: return 8; default: return 16; endcase
  endfunction
  function automatic bit is_wrap(input logic [2:0] b);
    return b == WRAP4 || b == WRAP8 || b == WRAP16;
  endfunction

  // The address of the beat after the one at a: the size in bytes further on; a wrapping burst
  // returns to the start of its window (beats x size bytes, aligned to that total) at the window's end.
  function automatic int unsigned next_addr(input int unsigned a, input logic [2:0] size, input logic [2:0] b);
    int unsigned nb = 1 << size;
    int unsigned window = nb * beats_of(b);
    int unsigned base;
    if (!is_wrap(b)) return a + nb;
    base = (a / window) * window;
    if (a + nb >= base + window) return base;
    return a + nb;
  endfunction

  // The address of beat n of a burst that starts at start.
  function automatic int unsigned beat_addr(input int unsigned start, input logic [2:0] size, input logic [2:0] b, input int n);
    int unsigned a = start;
    for (int k = 0; k < n; k++) a = next_addr(a, size, b);
    return a;
  endfunction

  // The lanes a transfer at address a uses on a bus of bus_bytes bytes, packed as {upper, lower}.
  // Every AHB transfer is aligned to its size, so it uses size bytes from its own lane upwards.
  function automatic logic [15:0] beat_lanes(input int unsigned a, input logic [2:0] size, input int bus_bytes);
    int lower = a % bus_bytes;
    int upper = lower + (1 << size) - 1;
    if (upper > bus_bytes - 1) upper = bus_bytes - 1;
    return {upper[7:0], lower[7:0]};
  endfunction

  // The strobe of a transfer: a 1 for every lane it uses (bit l is lane l).
  function automatic logic [63:0] beat_strb(input int unsigned a, input logic [2:0] size, input int bus_bytes);
    logic [15:0] lanes = beat_lanes(a, size, bus_bytes);
    logic [63:0] s = 0;
    for (int l = lanes[7:0]; l <= lanes[15:8]; l++) s[l] = 1'b1;
    return s;
  endfunction

  function automatic bit aligned(input int unsigned a, input logic [2:0] size);
    return (a % (1 << size)) == 0;
  endfunction

  // True when an incrementing burst of n beats (n is used only for INCR) crosses a 1 KB boundary.
  function automatic bit crosses_1k(input int unsigned start, input logic [2:0] size, input logic [2:0] b, input int n);
    int beats = beats_of(b) ? beats_of(b) : n;
    if (is_wrap(b) || beats < 2) return 0;
    return (start / 1024) != ((start + beats * (1 << size) - 1) / 1024);
  endfunction
endpackage
Read included file: ahb_mem.sv
`timescale 1ns/1ns
// ahb_mem.sv: an AHB subordinate with a byte-addressed memory behind it (read-only in this lesson).
// It registers an address phase at an edge where HSEL is 1, HTRANS is NONSEQ or SEQ and HREADY is 1,
// then runs the data phase: wait states with HREADYOUT low, a write takes HWDATA (and HWSTRB) at the
// edge that ends the data phase, a read drives HRDATA for the cycle that ends it. IDLE and BUSY get a
// zero-wait OKAY and change nothing. The switches below are plain variables: the stimulus sets them by
// name (mem.waits = 2;).
//   waits          wait states inserted in every data phase
//   waits_at[k]    wait states for the k-th transfer this memory takes (from 0; -1 = use waits)
//   err_above      transfers at or above this address get the two-cycle ERROR (and write nothing)
//   excl_on        AHB5 exclusive access: one monitor per HMASTER, HEXOKAY on success
//   trace          print every transfer the memory takes and every byte it writes
// Broken twins, each off by default:
//   ignore_hready    registers an address phase while HREADY is low (another subordinate is stretching),
//                    so it acts on a transfer the manager may still change or cancel
//   wdata_in_addr    takes HWDATA in the address phase, so a write stores the previous transfer's data
//   act_on_idle      treats IDLE and BUSY as transfers (waits, reads, writes HWDATA); this twin is an
//                    AHB-Lite design without an HWSTRB input, so it writes the lanes HSIZE selects
//   one_cycle_error  answers ERROR in one cycle (HRESP high with HREADYOUT high)
//   ignore_size      writes every lane of the bus word, whatever HSIZE and HWSTRB say
module ahb_mem #(parameter int DATA_W = 32, parameter int DEPTH = 65536) (
  input  logic              hclk,
  input  logic              hresetn,
  input  logic              hsel,
  input  logic [31:0]       haddr,
  input  logic [1:0]        htrans,
  input  logic              hwrite,
  input  logic [2:0]        hsize,
  input  logic [2:0]        hburst,
  input  logic [3:0]        hprot,
  input  logic              hmastlock,
  input  logic [DATA_W-1:0] hwdata,
  input  logic [DATA_W/8-1:0] hwstrb,
  input  logic              hexcl,
  input  logic [3:0]        hmaster,
  input  logic              hready,
  output logic              hreadyout,
  output logic              hresp,
  output logic [DATA_W-1:0] hrdata,
  output logic              hexokay
);
  import ahb_pkg::*;
  localparam int BUS = DATA_W / 8;

  // ---- switches ----
  int waits = 0;
  int waits_at [0:63];
  int unsigned err_above = 32'hffff_ffff;
  bit excl_on = 0, trace = 0;
  bit ignore_hready = 0, wdata_in_addr = 0, act_on_idle = 0, one_cycle_error = 0, ignore_size = 0;

  // ---- the memory ----
  logic [7:0] mem [0:DEPTH-1];
  int cycle = -1;
  int taken = 0;                              // transfers taken so far

  // ---- the data phase in progress ----
  bit              d_valid = 0, d_write = 0, d_err = 0, d_exok = 0, d_xfail = 0;
  int unsigned     d_addr = 0;
  logic [2:0]      d_size = 0;
  logic [1:0]      d_trans = 0;
  logic [DATA_W-1:0] d_wd = 0;                // HWDATA seen in the address phase (the wdata_in_addr twin)
  int              d_cnt = 0;                 // wait states still to insert
  bit              e_two = 0;                 // the ERROR response is in its second cycle

  // ---- exclusive monitors, one per HMASTER ----
  bit          mon_use [0:15];
  int unsigned mon_addr [0:15];
  int          mon_bytes [0:15];

  initial begin
    for (int i = 0; i < DEPTH; i++) mem[i] = 8'h00;
    for (int k = 0; k < 64; k++) waits_at[k] = -1;
    for (int m = 0; m < 16; m++) mon_use[m] = 0;
    hreadyout = 1; hresp = 0; hrdata = 0; hexokay = 0;
  end

  function automatic logic [DATA_W-1:0] read_word(input int unsigned a);
    logic [DATA_W-1:0] w = 0;
    int unsigned word = (a / BUS) * BUS;
    for (int l = 0; l < BUS; l++) w[8*l +: 8] = mem[(word + l) % DEPTH];
    return w;
  endfunction

  // Write the lanes of one transfer: the lanes its address and size select, where the strobe is 1.
  task automatic write_bytes(input int unsigned a, input logic [2:0] size, input logic [DATA_W-1:0] data, input logic [BUS-1:0] strb);
    logic [15:0] lanes = beat_lanes(a, size, BUS);
    int unsigned word = (a / BUS) * BUS;
    int lo = ignore_size ? 0 : lanes[7:0];
    int hi = ignore_size ? BUS - 1 : lanes[15:8];
    for (int l = lo; l <= hi; l++)
      if (ignore_size || act_on_idle || strb[l]) begin
        mem[(word + l) % DEPTH] = data[8*l +: 8];
        if (trace) $display("mem e%0d:   byte 0x%0h <= %02h (lane %0d)", cycle, word + l, data[8*l +: 8], l);
      end
    // any write ends the exclusive monitors that cover one of its bytes
    for (int m = 0; m < 16; m++)
      if (mon_use[m] && a < mon_addr[m] + mon_bytes[m] && mon_addr[m] < a + (1 << size)) mon_use[m] = 0;
  endtask

  always @(posedge hclk) begin
    cycle = cycle + 1;
    if (!hresetn) begin
      d_valid = 0; e_two = 0;
      hreadyout <= 1; hresp <= 0; hexokay <= 0;
    end else begin
      // 1. the data phase that ends or waits at this edge
      if (d_valid) begin
        if (hreadyout && hready) begin
          if (d_write && !d_err && !d_xfail)
            write_bytes(d_addr, d_size, wdata_in_addr ? d_wd : hwdata, hwstrb);
          d_valid = 0;
        end else if (!hreadyout) begin
          if (d_cnt > 0) d_cnt = d_cnt - 1;
          else if (d_err) e_two = 1;
        end
      end
      // 2. the address phase on the wires at this edge
      if (hsel && (htrans[1] || act_on_idle) && (hready || (ignore_hready && !d_valid))) begin
        d_valid = 1; d_addr = haddr; d_write = hwrite; d_size = hsize; d_trans = htrans; d_wd = hwdata;
        d_cnt = (taken < 64 && waits_at[taken] >= 0) ? waits_at[taken] : waits;
        taken = taken + 1;
        d_err = (haddr >= err_above); e_two = 0;
        d_exok = 0; d_xfail = 0;
        if (excl_on && hexcl && htrans[1] && !d_err) begin
          if (!hwrite) begin
            mon_use[hmaster] = 1; mon_addr[hmaster] = haddr; mon_bytes[hmaster] = 1 << hsize; d_exok = 1;
          end else if (mon_use[hmaster] && mon_addr[hmaster] == haddr && mon_bytes[hmaster] == (1 << hsize)) begin
            d_exok = 1; mon_use[hmaster] = 0;
          end else d_xfail = 1;
        end
        if (trace) $display("mem e%0d: %0s %0s 0x%0h size %0d%0s%0s%0s", cycle, trans_name(htrans), hwrite ? "write" : "read", haddr, hsize,
                            opt(!hready, " (taken while HREADY is low)"), opt(d_err, " -> ERROR"),
                            opt(d_xfail, " -> exclusive failed"));
      end
      // 3. the response for the cycle that starts now
      if (d_valid && d_cnt > 0) begin
        hreadyout <= 0; hresp <= 0; hexokay <= 0;
      end else if (d_valid && d_err) begin
        hreadyout <= one_cycle_error ? 1'b1 : e_two; hresp <= 1; hexokay <= 0;
      end else begin
        hreadyout <= 1; hresp <= 0; hexokay <= d_valid && d_exok;
      end
      if (d_valid && !d_write) hrdata <= d_err ? '0 : read_word(d_addr);
    end
  end
endmodule
Read included file: ahb_checker.sv
`timescale 1ns/1ns
// ahb_checker.sv: the rules of an AHB interface, checked at every rising edge (read-only).
// Each broken rule is named with the edge where it was seen:
//   reset         HTRANS is not IDLE, or HREADY is low, while reset is active;
//   hold          the address or control changed during a wait state (HREADY low), outside the
//                 changes the protocol allows;
//   trans_change  HTRANS changed during a wait state other than IDLE to NONSEQ, BUSY to SEQ (fixed
//                 bursts) or BUSY to anything (INCR); or SEQ/BUSY with no burst in progress;
//   seq_addr      a SEQ or BUSY address that is not the previous beat's address plus the size
//                 (wrapped for a WRAP burst);
//   burst_ctrl    HSIZE, HBURST, HWRITE or HPROT changed inside a burst;
//   align         a transfer not aligned to its size;
//   size_bus      a transfer wider than the data bus;
//   kb1           an incrementing burst that crosses a 1 KB boundary;
//   burst_len     a fixed-length burst that ends early or runs long, BUSY after a SINGLE, or BUSY
//                 after the last beat of a fixed-length burst;
//   idle_okay     an IDLE or BUSY transfer that did not get a zero-wait OKAY;
//   err_shape     an ERROR that is not two cycles (HREADY low then high, HRESP high in both);
//   exokay        HEXOKAY with HREADY low, with an ERROR, or for a transfer that was not exclusive;
//   known         x on the address, control, or the active lanes of the data.
// A NOTE (not a broken rule) marks a transfer kept after the first cycle of an ERROR: the protocol
// allows it, most managers cancel.
module ahb_checker #(parameter int DATA_W = 32) (
  input logic              hclk,
  input logic              hresetn,
  input logic [31:0]       haddr,
  input logic [1:0]        htrans,
  input logic              hwrite,
  input logic [2:0]        hsize,
  input logic [2:0]        hburst,
  input logic [3:0]        hprot,
  input logic              hmastlock,
  input logic [DATA_W-1:0] hwdata,
  input logic              hexcl,
  input logic              hready,
  input logic              hresp,
  input logic [DATA_W-1:0] hrdata,
  input logic              hexokay
);
  import ahb_pkg::*;
  localparam int BUS = DATA_W / 8;
  int cycle = -1, transfers = 0, waits = 0, errors = 0, broken = 0, notes = 0;

  function void report(input string rule, input string what);
    broken++;
    $display("RULE %s broken at edge %0d: %s", rule, cycle, what);
  endfunction

  function automatic logic [DATA_W-1:0] lane_mask(input int unsigned a, input logic [2:0] size);
    logic [15:0] lanes = beat_lanes(a, size, BUS);
    logic [DATA_W-1:0] m = '0;
    for (int l = lanes[7:0]; l <= lanes[15:8]; l++) m[8*l +: 8] = 8'hff;
    return m;
  endfunction

  // The previous edge.
  bit          p_on = 0;
  logic        p_ready = 1, p_resp = 0, p_write = 0, p_lock = 0;
  logic [1:0]  p_trans = 0;
  logic [31:0] p_addr = 0;
  logic [2:0]  p_size = 0, p_burst = 0;
  logic [3:0]  p_prot = 0;
  bit          e_first = 0;           // the previous edge was the first cycle of an ERROR
  // The data phase in progress.
  bit          d_on = 0, d_idle = 0, d_write = 0, d_excl = 0;
  int unsigned d_addr = 0;
  logic [2:0]  d_size = 0;
  // The burst in progress.
  bit          b_on = 0, b_err = 0, b_write = 0, b_kb = 0;
  logic [2:0]  b_burst = 0, b_size = 0;
  logic [3:0]  b_prot = 0;
  int unsigned b_first = 0, b_last = 0;
  int          b_count = 0;
  int unsigned exp_a;

  task automatic end_burst();
    if (b_on && beats_of(b_burst) > 1 && b_count < beats_of(b_burst) && !b_err)
      report("burst_len", $sformatf("%0s burst at 0x%0h ended after %0d of %0d beats", burst_name(b_burst), b_first, b_count, beats_of(b_burst)));
    b_on = 0;
  endtask

  task automatic check_beat();
    if ((1 << hsize) > BUS) report("size_bus", $sformatf("a %0d-byte transfer on a %0d-byte bus", 1 << hsize, BUS));
    if (!aligned(haddr, hsize)) report("align", $sformatf("a %0d-byte transfer at 0x%0h is not aligned to its size", 1 << hsize, haddr));
  endtask

  task automatic check_ctrl(input string what);
    if (hsize !== b_size || hburst !== b_burst || hwrite !== b_write || hprot !== b_prot)
      report("burst_ctrl", $sformatf("%0s at 0x%0h changed HSIZE, HBURST, HWRITE or HPROT inside the burst", what, haddr));
  endtask

  always @(posedge hclk) begin
    cycle++;
    if (!hresetn) begin
      if (htrans !== IDLE) report("reset", "HTRANS is not IDLE during reset");
      if (hready !== 1) report("reset", "HREADY is low during reset");
      p_on = 0; d_on = 0; b_on = 0; e_first = 0;
    end else begin
      // ---- the data phase that ends or waits at this edge ----
      if (hready === 0) waits++;
      if (e_first) begin
        if (hresp !== 1 || hready !== 1) report("err_shape", "the second cycle of an ERROR must have HRESP high and HREADY high");
      end else if (hresp === 1 && hready === 1)
        report("err_shape", "ERROR with HREADY high in its first cycle: an ERROR takes two cycles");
      if (hresp === 1 && b_on) b_err = 1;
      if (d_on && d_idle) begin
        if (hready !== 1 || hresp !== 0) report("idle_okay", "an IDLE or BUSY transfer must get a zero-wait OKAY");
        d_on = 0;
      end
      if (hexokay === 1) begin
        if (hready !== 1) report("exokay", "HEXOKAY while HREADY is low");
        else if (hresp === 1) report("exokay", "HEXOKAY together with an ERROR");
        else if (!(d_on && d_excl)) report("exokay", "HEXOKAY for a transfer that was not exclusive");
      end
      if (hready === 1 && d_on && !d_idle) begin
        if (d_write && $isunknown(hwdata & lane_mask(d_addr, d_size))) report("known", "HWDATA is x on an active lane");
        if (!d_write && hresp === 0 && $isunknown(hrdata & lane_mask(d_addr, d_size))) report("known", "HRDATA is x on an active lane");
        transfers++;
        if (hresp === 1) errors++;
        d_on = 0;
      end
      if (e_first && hready === 1 && (htrans === NONSEQ || htrans === SEQ)) begin
        notes++;
        $display("NOTE cancel at edge %0d: the %0s at 0x%0h behind an ERROR was kept, not cancelled (allowed; most managers cancel)", cycle, trans_name(htrans), haddr);
      end
      // ---- the address phase on the wires at this edge ----
      if (htrans !== IDLE && ($isunknown(haddr) || $isunknown(hwrite) || $isunknown(hsize) || $isunknown(hburst)))
        report("known", "address or control is x while HTRANS is not IDLE");
      if ($isunknown(htrans)) report("known", "HTRANS is x");
      if (p_on && p_ready === 0 && !e_first) begin
        // a wait state at the previous edge: only the allowed changes
        if (p_trans == IDLE) begin
          if (htrans === BUSY || htrans === SEQ) report("trans_change", $sformatf("IDLE changed to %0s during a wait state (only NONSEQ may follow)", trans_name(htrans)));
        end else if (p_trans == BUSY) begin
          if (p_burst != INCR) begin
            if (htrans !== BUSY && htrans !== SEQ) report("trans_change", $sformatf("BUSY in a %0s burst changed to %0s during a wait state (only SEQ may follow)", burst_name(p_burst), trans_name(htrans)));
            else if (haddr !== p_addr) report("hold", $sformatf("HADDR changed from 0x%0h to 0x%0h during a wait state", p_addr, haddr));
          end
        end else begin
          if (htrans !== p_trans) report("trans_change", $sformatf("%0s changed to %0s during a wait state", trans_name(p_trans), trans_name(htrans)));
          else if (haddr !== p_addr) report("hold", $sformatf("HADDR changed from 0x%0h to 0x%0h during a wait state", p_addr, haddr));
          else if (hwrite !== p_write || hsize !== p_size || hburst !== p_burst || hprot !== p_prot || hmastlock !== p_lock)
            report("hold", "HWRITE, HSIZE, HBURST, HPROT or HMASTLOCK changed during a wait state");
        end
      end
      if (hready === 1) begin
        // the address phase is accepted at this edge
        if (htrans === IDLE) begin
          end_burst();
          d_on = 1; d_idle = 1;
        end else if (htrans === NONSEQ) begin
          end_burst();
          check_beat();
          b_on = 1; b_err = 0; b_kb = 0; b_first = haddr; b_last = haddr; b_count = 1;
          b_burst = hburst; b_size = hsize; b_write = hwrite; b_prot = hprot;
          d_on = 1; d_idle = 0; d_write = hwrite; d_addr = haddr; d_size = hsize; d_excl = hexcl;
        end else if (htrans === SEQ) begin
          if (!b_on) report("trans_change", $sformatf("SEQ at 0x%0h with no burst in progress", haddr));
          else begin
            exp_a = next_addr(b_last, b_size, b_burst);
            if (haddr !== exp_a) report("seq_addr", $sformatf("SEQ at 0x%0h; the beat after 0x%0h in a %0s burst of %0d-byte transfers is 0x%0h", haddr, b_last, burst_name(b_burst), 1 << b_size, exp_a));
            check_ctrl("SEQ");
            if (!is_wrap(b_burst) && !b_kb && (haddr / 1024) != (b_first / 1024)) begin
              b_kb = 1;
              report("kb1", $sformatf("SEQ at 0x%0h crosses the 1 KB boundary of the burst that started at 0x%0h", haddr, b_first));
            end
            b_count++;
            if (beats_of(b_burst) > 0 && b_count > beats_of(b_burst))
              report("burst_len", $sformatf("beat %0d of a %0s burst, which has %0d beats", b_count, burst_name(b_burst), beats_of(b_burst)));
            b_last = haddr;
          end
          check_beat();
          d_on = 1; d_idle = 0; d_write = hwrite; d_addr = haddr; d_size = hsize; d_excl = hexcl;
        end else if (htrans === BUSY) begin
          if (!b_on) report("trans_change", $sformatf("BUSY at 0x%0h with no burst in progress", haddr));
          else if (b_burst == SINGLE) report("burst_len", "BUSY after a SINGLE transfer");
          else begin
            exp_a = next_addr(b_last, b_size, b_burst);
            if (beats_of(b_burst) > 1 && b_count == beats_of(b_burst))
              report("burst_len", $sformatf("BUSY after the last beat of the %0s burst (a fixed-length burst ends with SEQ)", burst_name(b_burst)));
            else if (haddr !== exp_a) report("seq_addr", $sformatf("BUSY at 0x%0h must show the next beat's address 0x%0h", haddr, exp_a));
            check_ctrl("BUSY");
          end
          d_on = 1; d_idle = 1;
        end
      end
      e_first = (hresp === 1 && hready === 0);
    end
    p_on = hresetn; p_ready = hready; p_resp = hresp; p_trans = htrans; p_addr = haddr; p_write = hwrite;
    p_size = hsize; p_burst = hburst; p_prot = hprot; p_lock = hmastlock;
  end
  final $display("checker: %0d transfers, %0d wait edges, %0d errors, %0d rules broken", transfers, waits, errors, broken);
endmodule
Read included file: ahb_tasks.svh
// ahb_tasks.svh: the manager side of the bench, as tasks for the stimulus (read-only).
// ahb_write, ahb_read and ahb_burst queue transfers; go() puts the queue on the bus and returns when
// the last data phase has ended. The driver below issues the next address phase at the same edge where
// the previous one is accepted, so the address of transfer N+1 is on the wires during the data phase
// of transfer N. Write data for a burst goes in wd[0], wd[1], ... (one entry per beat, the lowest byte
// at the lowest address); the data of every read comes back in rd[0], rd[1], ... in issue order, with
// the responses in rr[].
// The beat log has one line per accepted address phase (A), per ended data phase (D) and per transfer
// the manager cancels (X), each with the edge where it happened; watch = 1 adds one line per edge.
int cycle = -1;
always @(posedge hclk) cycle = cycle + 1;

localparam int QN = 512;
int unsigned q_addr [0:QN-1];
logic        q_write [0:QN-1];
logic [2:0]  q_size [0:QN-1];
logic [2:0]  q_burst [0:QN-1];
logic [1:0]  q_trans [0:QN-1];
logic [63:0] q_data [0:QN-1];
logic        q_lock [0:QN-1], q_excl [0:QN-1], q_sforce [0:QN-1];
logic [3:0]  q_prot [0:QN-1], q_master [0:QN-1];
logic [2:0]  q_pext [0:QN-1];                 // AHB5: HPROT[6:4] (with AHB5_PROT defined)
logic        q_nsec [0:QN-1];                 // AHB5: HNONSEC (with AHB5_PROT defined)
logic [7:0]  q_strb [0:QN-1];
int          q_bn [0:QN-1], q_beat [0:QN-1], q_state [0:QN-1];   // burst number, beat, 0 queued 1 done 2 cancelled
logic [63:0] q_rdata [0:QN-1];
logic        q_resp [0:QN-1], q_exok [0:QN-1];
int q_n = 0, q_next = 0, bn = 0, last_start = 0, last_bn = 0;

logic [63:0] wd [0:255];
logic [63:0] rd [0:255];
logic        rr [0:255];
int          n_rd = 0;
logic        last_resp = 0, last_exokay = 0;
// quiet = 1 silences the beat log; watch = 1 prints the bus at every edge.
bit quiet = 0, watch = 0, running = 0, drv_done = 0;
// Driver switches (broken twins, off by default):
//   move_in_wait  the address moves on by one transfer size during a wait state
//   no_cancel     the transfer behind an ERROR is not cancelled (allowed, but the checker notes it)
// After the first cycle of an ERROR the driver cancels the transfer already in its address phase: the
// rest of the same burst is dropped; a separate transfer is issued again afterwards (reissue = 0 drops it).
//   busy_end      a BUSY after the last beat of every fixed-length burst
//   cross_1k      incrementing bursts are issued across a 1 KB boundary instead of being split
//   unaligned     transfers not aligned to their size are issued instead of refused
//   wrap_bug      a WRAP8 burst's addresses wrap inside 16 bytes, as if it were WRAP4
bit reissue = 1;
bit move_in_wait = 0, no_cancel = 0, busy_end = 0, cross_1k = 0, unaligned = 0, wrap_bug = 0;
// Attributes of the transfers queued next.
logic       lock = 0, excl = 0;
logic [3:0] prot = 4'b0011, master = 0;
// AHB5 (IHI 0033C 3.9, 3.10), used only by a bench built with ahb5: HPROT[6:4] and HNONSEC.
logic [2:0] prot_ext = 0;
logic       nonsec = 0;
bit         strb_force = 0;
logic [7:0] strb_val = 8'hff;
// What the bus is carrying in the data phase, for the waveform scenes: the address and lanes of the beat.
int unsigned beat_a = 0;
logic [7:0]  beat_m = 0;

function automatic int unsigned m_next(input int unsigned a, input logic [2:0] size, input logic [2:0] b);
  if (wrap_bug && b == WRAP8) return next_addr(a, size, WRAP4);
  return next_addr(a, size, b);
endfunction

task automatic q_push(input int unsigned a, input logic w, input logic [2:0] size, input logic [2:0] b, input logic [1:0] t,
                      input logic [63:0] data, input int burst_no, input int beat);
  q_addr[q_n] = a; q_write[q_n] = w; q_size[q_n] = size; q_burst[q_n] = b; q_trans[q_n] = t; q_data[q_n] = data;
  q_lock[q_n] = lock; q_excl[q_n] = excl; q_prot[q_n] = prot; q_master[q_n] = master;
  q_pext[q_n] = prot_ext; q_nsec[q_n] = nonsec;
  q_sforce[q_n] = strb_force; q_strb[q_n] = strb_val;
  q_bn[q_n] = burst_no; q_beat[q_n] = beat; q_state[q_n] = 0; q_resp[q_n] = 0; q_exok[q_n] = 0; q_rdata[q_n] = 0;
  q_n = q_n + 1;
endtask

task automatic q_copy(input int dst, input int src);
  q_addr[dst] = q_addr[src]; q_write[dst] = q_write[src]; q_size[dst] = q_size[src]; q_burst[dst] = q_burst[src];
  q_trans[dst] = q_trans[src]; q_data[dst] = q_data[src]; q_lock[dst] = q_lock[src]; q_excl[dst] = q_excl[src];
  q_prot[dst] = q_prot[src]; q_master[dst] = q_master[src]; q_sforce[dst] = q_sforce[src]; q_strb[dst] = q_strb[src];
  q_pext[dst] = q_pext[src]; q_nsec[dst] = q_nsec[src];
  q_bn[dst] = q_bn[src]; q_beat[dst] = q_beat[src]; q_state[dst] = q_state[src];
endtask

// One write of size bytes (0 = byte, 1 = halfword, 2 = word) at addr; data holds the bytes, lowest first.
task automatic ahb_write(input int unsigned addr, input logic [2:0] size, input logic [63:0] data);
  if (!unaligned && !aligned(addr, size))
    $display("refused: a %0d-byte transfer at 0x%0h is not aligned (every AHB transfer is aligned to its size)", 1 << size, addr);
  else begin
    bn = bn + 1; last_start = q_n; last_bn = bn;
    q_push(addr, 1, size, SINGLE, NONSEQ, data, bn, 0);
  end
endtask

// One read of size bytes at addr; the bytes come back in rd[] in issue order.
task automatic ahb_read(input int unsigned addr, input logic [2:0] size);
  if (!unaligned && !aligned(addr, size))
    $display("refused: a %0d-byte transfer at 0x%0h is not aligned (every AHB transfer is aligned to its size)", 1 << size, addr);
  else begin
    bn = bn + 1; last_start = q_n; last_bn = bn;
    q_push(addr, 0, size, SINGLE, NONSEQ, 0, bn, 0);
  end
endtask

// A burst: hburst SINGLE, INCR (beats gives its length), WRAP4, INCR4, ... INCR16. Write data from wd[].
// An incrementing burst that would cross a 1 KB boundary is issued as two INCR bursts split at the
// boundary (unless cross_1k is set).
task automatic ahb_burst(input logic w, input logic [2:0] hb, input int unsigned addr, input logic [2:0] size, input int beats = 0);
  int n;
  int unsigned a;
  logic [2:0] b;
  logic [1:0] t;
  bit split;
  n = beats_of(hb) ? beats_of(hb) : (beats > 0 ? beats : 1);
  a = addr; b = hb; split = 0;
  if (!unaligned && !aligned(addr, size))
    $display("refused: a %0d-byte burst at 0x%0h is not aligned (every AHB transfer is aligned to its size)", 1 << size, addr);
  else begin
    if (!cross_1k && crosses_1k(addr, size, hb, n)) begin
      split = 1; b = INCR;
      $display("note: %0s at 0x%0h would cross a 1 KB boundary; issued as INCR bursts split at the boundary", burst_name(hb), addr);
    end
    bn = bn + 1; last_start = q_n; last_bn = bn;
    for (int k = 0; k < n; k++) begin
      t = (k == 0) ? NONSEQ : SEQ;
      if (k > 0 && split && (a % 1024) == 0) begin t = NONSEQ; bn = bn + 1; end
      q_push(a, w, size, b, t, w ? wd[k] : 64'h0, bn, k);
      a = m_next(a, size, b);
    end
    if (busy_end && beats_of(b) > 1) q_push(a, w, size, b, BUSY, 64'h0, bn, n);
  end
endtask

// n BUSY cycles before beat k of the burst queued last (k = its length: after the last beat).
task automatic busy_at(input int k, input int n = 1);
  int idx, src;
  idx = q_n;
  for (int j = q_n - 1; j >= last_start; j--)
    if (q_trans[j][1] && q_beat[j] == k) idx = j;
  src = (idx < q_n) ? idx : q_n - 1;           // the beat the BUSY announces, or the last beat
  for (int j = q_n - 1; j >= idx; j--) q_copy(j + n, j);
  for (int j = 0; j < n; j++) begin
    q_copy(idx + j, src >= idx ? src + n : src);
    q_trans[idx + j] = BUSY; q_data[idx + j] = 0; q_beat[idx + j] = k;
    if (src < idx) q_addr[idx + j] = m_next(q_addr[src], q_size[src], q_burst[src]);
  end
  q_n = q_n + n;
endtask

// n IDLE cycles in the queue (the address and control keep their last values).
task automatic idle_q(input int n);
  for (int j = 0; j < n; j++)
    if (q_n > 0) q_push(q_addr[q_n - 1], q_write[q_n - 1], q_size[q_n - 1], q_burst[q_n - 1], IDLE, 64'h0, 0, 0);
    else q_push(0, 0, 0, SINGLE, IDLE, 64'h0, 0, 0);
endtask

// The driver: pick, hold, cancel.
int a_idx = -1, d_idx = -1;       // queue entries in the address phase and in the data phase (-1: none)
bit moved = 0;
logic        s_ready, s_resp, s_exok, s_write;
logic [DATA_W-1:0] s_rdata;
logic [31:0] s_addr;
logic [1:0]  s_trans;
logic [2:0]  s_size, s_burst;
int          s_done, s_acc, s_cfrom, s_cto, s_cmode;

task automatic complete(input int i);
  logic [15:0] lanes;
  logic [63:0] bytes;
  q_state[i] = 1; q_resp[i] = s_resp; q_exok[i] = s_exok; last_resp = s_resp; last_exokay = s_exok;
  if (!q_write[i]) begin
    lanes = beat_lanes(q_addr[i], q_size[i], BUS_BYTES);
    bytes = (s_rdata >> (8 * lanes[7:0])) & ((64'h1 << (8 * (lanes[15:8] - lanes[7:0] + 1))) - 1);
    q_rdata[i] = bytes; rd[n_rd] = bytes; rr[n_rd] = s_resp; n_rd = n_rd + 1;
  end
  if (!quiet) $display("e%0d D  %0s addr=0x%0h data=0x%0h %0s%0s", cycle, q_write[i] ? "write" : "read ", q_addr[i],
                       q_write[i] ? q_data[i] : q_rdata[i], resp_name(s_resp),
                       opt(q_excl[i], s_exok ? " EXOKAY" : " (HEXOKAY low: exclusive failed)"));
endtask

task automatic drive();
  logic [15:0] lanes;
  logic [63:0] s;
  int e;
  if (a_idx >= 0) begin
    e = a_idx;
    htrans = q_trans[e]; haddr = q_addr[e] + (moved ? (1 << q_size[e]) : 0); hwrite = q_write[e]; hsize = q_size[e];
    hburst = q_burst[e]; hprot = q_prot[e]; hmastlock = q_lock[e]; hexcl = q_excl[e]; hmaster = q_master[e];
`ifdef AHB5_PROT
    hprot_ext = q_pext[e]; hnonsec = q_nsec[e];
`endif
  end else begin
    htrans = IDLE; hmastlock = 0; hexcl = 0;      // address and control keep their last values
  end
  if (d_idx >= 0 && q_write[d_idx]) begin
    lanes = beat_lanes(q_addr[d_idx], q_size[d_idx], BUS_BYTES);
    s = beat_strb(q_addr[d_idx], q_size[d_idx], BUS_BYTES);
    hwdata = q_data[d_idx] << (8 * lanes[7:0]);
    hwstrb = q_sforce[d_idx] ? q_strb[d_idx][BUS_BYTES-1:0] : s[BUS_BYTES-1:0];
    beat_a = q_addr[d_idx]; beat_m = hwstrb;
  end else begin
    hwdata = '0; hwstrb = '0; beat_m = 0;
  end
endtask

always @(posedge hclk) begin
  s_ready = hready; s_resp = hresp; s_exok = hexokay; s_rdata = hrdata; s_addr = haddr; s_trans = htrans;
  s_write = hwrite; s_size = hsize; s_burst = hburst;
  s_done = -1; s_acc = -1; s_cmode = 0;
  if (hresetn) begin
    if (s_ready === 1'b1) begin
      s_done = d_idx; d_idx = -1;
      if (a_idx >= 0 && moved) q_addr[a_idx] = s_addr;   // the address the subordinate took
      if (a_idx >= 0 && q_trans[a_idx] != IDLE) s_acc = a_idx;
      if (a_idx >= 0 && q_trans[a_idx][1]) d_idx = a_idx;
      a_idx = -1; moved = 0;
      if (running && q_next < q_n) begin a_idx = q_next; q_next = q_next + 1; end
    end else if (s_resp === 1'b1 && !no_cancel && a_idx >= 0 && q_trans[a_idx] != IDLE) begin
      // the first cycle of an ERROR: the transfer already on the wires is cancelled (IHI 0033C 5.1.3)
      s_cfrom = a_idx;
      if (d_idx >= 0 && q_bn[a_idx] == q_bn[d_idx]) begin
        s_cto = a_idx;
        while (s_cto < q_n && q_bn[s_cto] == q_bn[d_idx]) begin q_state[s_cto] = 2; s_cto = s_cto + 1; end
        q_next = s_cto; s_cmode = 1;               // the rest of the burst is dropped
      end else if (reissue) begin
        q_next = a_idx; s_cmode = 2;               // a separate transfer: issued again after the ERROR
      end else begin
        q_state[a_idx] = 2; s_cto = a_idx + 1; s_cmode = 3;   // a separate transfer, dropped
      end
      a_idx = -1;
    end else if (move_in_wait && a_idx >= 0 && q_trans[a_idx][1]) moved = 1;
  end
  #1;
  if (s_done >= 0) complete(s_done);
  if (s_acc >= 0 && !quiet)
    $display("e%0d A  %0s %0s addr=0x%0h size=%0d %0s%0s%0s", cycle, trans_name(s_trans), s_write ? "WRITE" : "READ", s_addr, s_size,
             burst_name(s_burst), opt(q_lock[s_acc], " locked"), opt(q_excl[s_acc], " exclusive"));
  if (s_cmode == 1 && !quiet)
    for (int j = s_cfrom; j < s_cto; j++)
      if (q_trans[j][1]) $display("e%0d X  cancelled %0s %0s addr=0x%0h (the rest of the burst is dropped)", cycle, trans_name(q_trans[j]), q_write[j] ? "WRITE" : "READ", q_addr[j]);
  if (s_cmode == 3 && !quiet)
    $display("e%0d X  cancelled %0s %0s addr=0x%0h", cycle, trans_name(q_trans[s_cfrom]), q_write[s_cfrom] ? "WRITE" : "READ", q_addr[s_cfrom]);
  if (s_cmode == 2 && !quiet)
    $display("e%0d X  withdrew %0s %0s addr=0x%0h (issued again after the ERROR)", cycle, trans_name(q_trans[s_cfrom]), q_write[s_cfrom] ? "WRITE" : "READ", q_addr[s_cfrom]);
  drive();
  drv_done = running && q_next >= q_n && a_idx < 0 && d_idx < 0;   // go() returns after this edge's log
end

// A text waveform for the lesson's trace blocks: with watch = 1, one line per rising edge with the
// values sampled at that edge (cycle k of a trace is what edge k sees).
int wave_edge = -1;
always @(posedge hclk) begin
  wave_edge = wave_edge + 1;
  if (watch) $display("wave e%0d: htrans=%0s haddr=%h hwrite=%b hsize=%0d hburst=%0s hwdata=%h hready=%b hresp=%b hrdata=%h",
                      wave_edge, trans_name(htrans), haddr, hwrite, hsize, burst_name(hburst), hwdata, hready, hresp, hrdata);
end

// Put the queue on the bus and wait until every transfer in it has ended; then empty the queue.
task automatic go();
  n_rd = 0; drv_done = 0; running = 1;
  wait (drv_done);
  running = 0; drv_done = 0; q_n = 0; q_next = 0;
endtask

// The table of a burst before it runs: the address, lanes and strobe of every beat.
task automatic beat_table(input int unsigned addr, input logic [2:0] size, input logic [2:0] hb, input int beats = 0);
  int n;
  int unsigned a, window, base;
  logic [15:0] lanes;
  logic [63:0] s;
  n = beats_of(hb) ? beats_of(hb) : (beats > 0 ? beats : 1);
  a = addr;
  $display("%0s at 0x%0h: %0d beat%0s of %0d byte%0s, bus %0d bytes", burst_name(hb), addr, n, opt(n > 1, "s"), 1 << size, opt(size != 0, "s"), BUS_BYTES);
  if (is_wrap(hb)) begin
    window = (1 << size) * beats_of(hb); base = (addr / window) * window;
    $display("  wraps inside 0x%0h-0x%0h (%0d beats x %0d bytes)", base, base + window - 1, beats_of(hb), 1 << size);
  end
  $display("  beat  address  lanes  strobe");
  for (int k = 0; k < n; k++) begin
    lanes = beat_lanes(a, size, BUS_BYTES);
    s = beat_strb(a, size, BUS_BYTES);
    $display("  %4d  0x%05h  %0d-%0d    %b", k, a[19:0], lanes[7:0], lanes[15:8], s[BUS_BYTES-1:0]);
    a = m_next(a, size, hb);
  end
  if (crosses_1k(addr, size, hb, n)) $display("  this burst crosses a 1 KB boundary");
  if (!aligned(addr, size)) $display("  0x%0h is not aligned to %0d bytes: AHB does not allow it", addr, 1 << size);
endtask

// One byte of the memory that owns an address (the fabric's second memory from 0x1000).
function automatic logic [7:0] mem_byte(input int unsigned a);
`ifdef AHB_MEM1
  if (a >= 32'h1000 && a < 32'h2000) return `AHB_MEM1.mem[a % `AHB_DEPTH];
  if (a >= 32'h1000) return 8'h00;
`endif
  return `AHB_MEM.mem[a % `AHB_DEPTH];
endfunction
task automatic set_byte(input int unsigned a, input logic [7:0] v);
`ifdef AHB_MEM1
  if (a >= 32'h1000 && a < 32'h2000) `AHB_MEM1.mem[a % `AHB_DEPTH] = v;
  else if (a < 32'h1000) `AHB_MEM.mem[a % `AHB_DEPTH] = v;
`else
  `AHB_MEM.mem[a % `AHB_DEPTH] = v;
`endif
endtask

// The memory, n bytes from addr, one bus word per group.
task automatic dump(input int unsigned addr, input int n);
  string line;
  int unsigned a = (addr / 16) * 16;
  while (a < addr + n) begin
    line = $sformatf("0x%05h ", a[19:0]);
    for (int i = 0; i < 16; i++) begin
      if (i % BUS_BYTES == 0) line = {line, " "};
      line = {line, $sformatf(" %02h", mem_byte(a + i))};
    end
    $display("%s", line);
    a = a + 16;
  end
endtask

// Fill n bytes from addr with first, first+1, ... so untouched bytes stay recognisable.
task automatic mem_fill(input int unsigned addr, input int n, input logic [7:0] first = 8'h00);
  for (int i = 0; i < n; i++) set_byte(addr + i, first + i[7:0]);
endtask

// Drive nothing new for n cycles.
task automatic idle(input int n);
  repeat (n) @(posedge hclk);
  #1;
endtask
Read included file: ahb5_attr_mon.sv
`timescale 1ns/1ns
// ahb5_attr_mon.sv: prints one line per accepted address phase (read-only).
// HPROT[6:2] gives the memory type by Table 3-7; a combination that table does not list is "not
// permitted". HNONSEC = 1 is Non-secure. HPROT[1] is privileged, HPROT[0] = 1 is a data access.
// It also reports an HNONSEC that changes inside a burst (it must be constant, 3.10).
module ahb5_attr_mon (
  input logic        hclk,
  input logic        hresetn,
  input logic [1:0]  htrans,
  input logic        hready,
  input logic        hwrite,
  input logic [31:0] haddr,
  input logic [6:0]  hprot,
  input logic        hnonsec);
  int cycle = -1, not_permitted = 0;   // not_permitted counts transfers whose HPROT Table 3-7 does not list
  logic b_nonsec = 0;
  string t;
  function automatic string mtype(input logic [6:2] p);
    case (p)
      5'b00000: return "Device-nE";
      5'b00001: return "Device-E";
      5'b00010: return "Normal Non-cacheable Non-shareable";
      5'b00110, 5'b01110: return "Write-through Non-shareable";
      5'b00111, 5'b01111: return "Write-back Non-shareable";
      5'b10010: return "Normal Non-cacheable Shareable";
      5'b10110, 5'b11110: return "Write-through Shareable";
      5'b10111, 5'b11111: return "Write-back Shareable";
      default: return "not permitted (Table 3-7)";
    endcase
  endfunction
  always @(posedge hclk) begin
    cycle = cycle + 1;
    if (hresetn && hready && htrans[1]) begin
      if (htrans == 2'b11 && hnonsec !== b_nonsec) $display("attr e%0d: HNONSEC changed inside a burst", cycle);
      if (htrans == 2'b10) b_nonsec = hnonsec;
      t = mtype(hprot[6:2]);
      if (t == "not permitted (Table 3-7)") not_permitted++;
      $display("attr e%0d: %0s 0x%0h %0s%0s, %0s, %0s, %0s", cycle, hwrite ? "write" : "read", haddr, t,
               (hprot[5] && hprot[4]) ? " allocate" : "", hnonsec ? "Non-secure" : "Secure",
               hprot[1] ? "privileged" : "unprivileged", hprot[0] ? "data" : "instruction");
    end
  end
endmodule
Spot the bugEach option queues one read with a different HPROT. Which one does Table 3-7 not permit?
Read included file: ahb_pkg.sv
`timescale 1ns/1ns
// ahb_pkg.sv: the encodings and the arithmetic of a burst (read-only).
// The memory, the driver, the checker and the lesson text all use these functions, so they never
// disagree about the address of a beat or the lanes it uses.
package ahb_pkg;
  localparam logic [1:0] IDLE = 2'b00, BUSY = 2'b01, NONSEQ = 2'b10, SEQ = 2'b11;
  localparam logic [2:0] SINGLE = 3'b000, INCR = 3'b001, WRAP4 = 3'b010, INCR4 = 3'b011,
                         WRAP8 = 3'b100, INCR8 = 3'b101, WRAP16 = 3'b110, INCR16 = 3'b111;
  localparam logic OKAY = 1'b0, ERROR = 1'b1;

  function automatic string trans_name(input logic [1:0] t);
    case (t) IDLE: return "IDLE"; BUSY: return "BUSY"; NONSEQ: return "NONSEQ"; default: return "SEQ"; endcase
  endfunction
  function automatic string burst_name(input logic [2:0] b);
    case (b)
      SINGLE: return "SINGLE"; INCR: return "INCR"; WRAP4: return "WRAP4"; INCR4: return "INCR4";
      WRAP8: return "WRAP8"; INCR8: return "INCR8"; WRAP16: return "WRAP16"; default: return "INCR16";
    endcase
  endfunction
  function automatic string resp_name(input logic r);
    return r ? "ERROR" : "OKAY";
  endfunction
  // s when c is 1, else the empty string (a string-typed result prints the same on every simulator).
  function automatic string opt(input bit c, input string s);
    if (c) return s;
    return "";
  endfunction

  // Beats in a burst: 1 for SINGLE, 4, 8 or 16 for the fixed bursts, 0 for INCR (undefined length).
  function automatic int beats_of(input logic [2:0] b);
    case (b) SINGLE: return 1; INCR: return 0; WRAP4, INCR4: return 4; WRAP8, INCR8: return 8; default: return 16; endcase
  endfunction
  function automatic bit is_wrap(input logic [2:0] b);
    return b == WRAP4 || b == WRAP8 || b == WRAP16;
  endfunction

  // The address of the beat after the one at a: the size in bytes further on; a wrapping burst
  // returns to the start of its window (beats x size bytes, aligned to that total) at the window's end.
  function automatic int unsigned next_addr(input int unsigned a, input logic [2:0] size, input logic [2:0] b);
    int unsigned nb = 1 << size;
    int unsigned window = nb * beats_of(b);
    int unsigned base;
    if (!is_wrap(b)) return a + nb;
    base = (a / window) * window;
    if (a + nb >= base + window) return base;
    return a + nb;
  endfunction

  // The address of beat n of a burst that starts at start.
  function automatic int unsigned beat_addr(input int unsigned start, input logic [2:0] size, input logic [2:0] b, input int n);
    int unsigned a = start;
    for (int k = 0; k < n; k++) a = next_addr(a, size, b);
    return a;
  endfunction

  // The lanes a transfer at address a uses on a bus of bus_bytes bytes, packed as {upper, lower}.
  // Every AHB transfer is aligned to its size, so it uses size bytes from its own lane upwards.
  function automatic logic [15:0] beat_lanes(input int unsigned a, input logic [2:0] size, input int bus_bytes);
    int lower = a % bus_bytes;
    int upper = lower + (1 << size) - 1;
    if (upper > bus_bytes - 1) upper = bus_bytes - 1;
    return {upper[7:0], lower[7:0]};
  endfunction

  // The strobe of a transfer: a 1 for every lane it uses (bit l is lane l).
  function automatic logic [63:0] beat_strb(input int unsigned a, input logic [2:0] size, input int bus_bytes);
    logic [15:0] lanes = beat_lanes(a, size, bus_bytes);
    logic [63:0] s = 0;
    for (int l = lanes[7:0]; l <= lanes[15:8]; l++) s[l] = 1'b1;
    return s;
  endfunction

  function automatic bit aligned(input int unsigned a, input logic [2:0] size);
    return (a % (1 << size)) == 0;
  endfunction

  // True when an incrementing burst of n beats (n is used only for INCR) crosses a 1 KB boundary.
  function automatic bit crosses_1k(input int unsigned start, input logic [2:0] size, input logic [2:0] b, input int n);
    int beats = beats_of(b) ? beats_of(b) : n;
    if (is_wrap(b) || beats < 2) return 0;
    return (start / 1024) != ((start + beats * (1 << size) - 1) / 1024);
  endfunction
endpackage
Read included file: ahb_mem.sv
`timescale 1ns/1ns
// ahb_mem.sv: an AHB subordinate with a byte-addressed memory behind it (read-only in this lesson).
// It registers an address phase at an edge where HSEL is 1, HTRANS is NONSEQ or SEQ and HREADY is 1,
// then runs the data phase: wait states with HREADYOUT low, a write takes HWDATA (and HWSTRB) at the
// edge that ends the data phase, a read drives HRDATA for the cycle that ends it. IDLE and BUSY get a
// zero-wait OKAY and change nothing. The switches below are plain variables: the stimulus sets them by
// name (mem.waits = 2;).
//   waits          wait states inserted in every data phase
//   waits_at[k]    wait states for the k-th transfer this memory takes (from 0; -1 = use waits)
//   err_above      transfers at or above this address get the two-cycle ERROR (and write nothing)
//   excl_on        AHB5 exclusive access: one monitor per HMASTER, HEXOKAY on success
//   trace          print every transfer the memory takes and every byte it writes
// Broken twins, each off by default:
//   ignore_hready    registers an address phase while HREADY is low (another subordinate is stretching),
//                    so it acts on a transfer the manager may still change or cancel
//   wdata_in_addr    takes HWDATA in the address phase, so a write stores the previous transfer's data
//   act_on_idle      treats IDLE and BUSY as transfers (waits, reads, writes HWDATA); this twin is an
//                    AHB-Lite design without an HWSTRB input, so it writes the lanes HSIZE selects
//   one_cycle_error  answers ERROR in one cycle (HRESP high with HREADYOUT high)
//   ignore_size      writes every lane of the bus word, whatever HSIZE and HWSTRB say
module ahb_mem #(parameter int DATA_W = 32, parameter int DEPTH = 65536) (
  input  logic              hclk,
  input  logic              hresetn,
  input  logic              hsel,
  input  logic [31:0]       haddr,
  input  logic [1:0]        htrans,
  input  logic              hwrite,
  input  logic [2:0]        hsize,
  input  logic [2:0]        hburst,
  input  logic [3:0]        hprot,
  input  logic              hmastlock,
  input  logic [DATA_W-1:0] hwdata,
  input  logic [DATA_W/8-1:0] hwstrb,
  input  logic              hexcl,
  input  logic [3:0]        hmaster,
  input  logic              hready,
  output logic              hreadyout,
  output logic              hresp,
  output logic [DATA_W-1:0] hrdata,
  output logic              hexokay
);
  import ahb_pkg::*;
  localparam int BUS = DATA_W / 8;

  // ---- switches ----
  int waits = 0;
  int waits_at [0:63];
  int unsigned err_above = 32'hffff_ffff;
  bit excl_on = 0, trace = 0;
  bit ignore_hready = 0, wdata_in_addr = 0, act_on_idle = 0, one_cycle_error = 0, ignore_size = 0;

  // ---- the memory ----
  logic [7:0] mem [0:DEPTH-1];
  int cycle = -1;
  int taken = 0;                              // transfers taken so far

  // ---- the data phase in progress ----
  bit              d_valid = 0, d_write = 0, d_err = 0, d_exok = 0, d_xfail = 0;
  int unsigned     d_addr = 0;
  logic [2:0]      d_size = 0;
  logic [1:0]      d_trans = 0;
  logic [DATA_W-1:0] d_wd = 0;                // HWDATA seen in the address phase (the wdata_in_addr twin)
  int              d_cnt = 0;                 // wait states still to insert
  bit              e_two = 0;                 // the ERROR response is in its second cycle

  // ---- exclusive monitors, one per HMASTER ----
  bit          mon_use [0:15];
  int unsigned mon_addr [0:15];
  int          mon_bytes [0:15];

  initial begin
    for (int i = 0; i < DEPTH; i++) mem[i] = 8'h00;
    for (int k = 0; k < 64; k++) waits_at[k] = -1;
    for (int m = 0; m < 16; m++) mon_use[m] = 0;
    hreadyout = 1; hresp = 0; hrdata = 0; hexokay = 0;
  end

  function automatic logic [DATA_W-1:0] read_word(input int unsigned a);
    logic [DATA_W-1:0] w = 0;
    int unsigned word = (a / BUS) * BUS;
    for (int l = 0; l < BUS; l++) w[8*l +: 8] = mem[(word + l) % DEPTH];
    return w;
  endfunction

  // Write the lanes of one transfer: the lanes its address and size select, where the strobe is 1.
  task automatic write_bytes(input int unsigned a, input logic [2:0] size, input logic [DATA_W-1:0] data, input logic [BUS-1:0] strb);
    logic [15:0] lanes = beat_lanes(a, size, BUS);
    int unsigned word = (a / BUS) * BUS;
    int lo = ignore_size ? 0 : lanes[7:0];
    int hi = ignore_size ? BUS - 1 : lanes[15:8];
    for (int l = lo; l <= hi; l++)
      if (ignore_size || act_on_idle || strb[l]) begin
        mem[(word + l) % DEPTH] = data[8*l +: 8];
        if (trace) $display("mem e%0d:   byte 0x%0h <= %02h (lane %0d)", cycle, word + l, data[8*l +: 8], l);
      end
    // any write ends the exclusive monitors that cover one of its bytes
    for (int m = 0; m < 16; m++)
      if (mon_use[m] && a < mon_addr[m] + mon_bytes[m] && mon_addr[m] < a + (1 << size)) mon_use[m] = 0;
  endtask

  always @(posedge hclk) begin
    cycle = cycle + 1;
    if (!hresetn) begin
      d_valid = 0; e_two = 0;
      hreadyout <= 1; hresp <= 0; hexokay <= 0;
    end else begin
      // 1. the data phase that ends or waits at this edge
      if (d_valid) begin
        if (hreadyout && hready) begin
          if (d_write && !d_err && !d_xfail)
            write_bytes(d_addr, d_size, wdata_in_addr ? d_wd : hwdata, hwstrb);
          d_valid = 0;
        end else if (!hreadyout) begin
          if (d_cnt > 0) d_cnt = d_cnt - 1;
          else if (d_err) e_two = 1;
        end
      end
      // 2. the address phase on the wires at this edge
      if (hsel && (htrans[1] || act_on_idle) && (hready || (ignore_hready && !d_valid))) begin
        d_valid = 1; d_addr = haddr; d_write = hwrite; d_size = hsize; d_trans = htrans; d_wd = hwdata;
        d_cnt = (taken < 64 && waits_at[taken] >= 0) ? waits_at[taken] : waits;
        taken = taken + 1;
        d_err = (haddr >= err_above); e_two = 0;
        d_exok = 0; d_xfail = 0;
        if (excl_on && hexcl && htrans[1] && !d_err) begin
          if (!hwrite) begin
            mon_use[hmaster] = 1; mon_addr[hmaster] = haddr; mon_bytes[hmaster] = 1 << hsize; d_exok = 1;
          end else if (mon_use[hmaster] && mon_addr[hmaster] == haddr && mon_bytes[hmaster] == (1 << hsize)) begin
            d_exok = 1; mon_use[hmaster] = 0;
          end else d_xfail = 1;
        end
        if (trace) $display("mem e%0d: %0s %0s 0x%0h size %0d%0s%0s%0s", cycle, trans_name(htrans), hwrite ? "write" : "read", haddr, hsize,
                            opt(!hready, " (taken while HREADY is low)"), opt(d_err, " -> ERROR"),
                            opt(d_xfail, " -> exclusive failed"));
      end
      // 3. the response for the cycle that starts now
      if (d_valid && d_cnt > 0) begin
        hreadyout <= 0; hresp <= 0; hexokay <= 0;
      end else if (d_valid && d_err) begin
        hreadyout <= one_cycle_error ? 1'b1 : e_two; hresp <= 1; hexokay <= 0;
      end else begin
        hreadyout <= 1; hresp <= 0; hexokay <= d_valid && d_exok;
      end
      if (d_valid && !d_write) hrdata <= d_err ? '0 : read_word(d_addr);
    end
  end
endmodule
Read included file: ahb_checker.sv
`timescale 1ns/1ns
// ahb_checker.sv: the rules of an AHB interface, checked at every rising edge (read-only).
// Each broken rule is named with the edge where it was seen:
//   reset         HTRANS is not IDLE, or HREADY is low, while reset is active;
//   hold          the address or control changed during a wait state (HREADY low), outside the
//                 changes the protocol allows;
//   trans_change  HTRANS changed during a wait state other than IDLE to NONSEQ, BUSY to SEQ (fixed
//                 bursts) or BUSY to anything (INCR); or SEQ/BUSY with no burst in progress;
//   seq_addr      a SEQ or BUSY address that is not the previous beat's address plus the size
//                 (wrapped for a WRAP burst);
//   burst_ctrl    HSIZE, HBURST, HWRITE or HPROT changed inside a burst;
//   align         a transfer not aligned to its size;
//   size_bus      a transfer wider than the data bus;
//   kb1           an incrementing burst that crosses a 1 KB boundary;
//   burst_len     a fixed-length burst that ends early or runs long, BUSY after a SINGLE, or BUSY
//                 after the last beat of a fixed-length burst;
//   idle_okay     an IDLE or BUSY transfer that did not get a zero-wait OKAY;
//   err_shape     an ERROR that is not two cycles (HREADY low then high, HRESP high in both);
//   exokay        HEXOKAY with HREADY low, with an ERROR, or for a transfer that was not exclusive;
//   known         x on the address, control, or the active lanes of the data.
// A NOTE (not a broken rule) marks a transfer kept after the first cycle of an ERROR: the protocol
// allows it, most managers cancel.
module ahb_checker #(parameter int DATA_W = 32) (
  input logic              hclk,
  input logic              hresetn,
  input logic [31:0]       haddr,
  input logic [1:0]        htrans,
  input logic              hwrite,
  input logic [2:0]        hsize,
  input logic [2:0]        hburst,
  input logic [3:0]        hprot,
  input logic              hmastlock,
  input logic [DATA_W-1:0] hwdata,
  input logic              hexcl,
  input logic              hready,
  input logic              hresp,
  input logic [DATA_W-1:0] hrdata,
  input logic              hexokay
);
  import ahb_pkg::*;
  localparam int BUS = DATA_W / 8;
  int cycle = -1, transfers = 0, waits = 0, errors = 0, broken = 0, notes = 0;

  function void report(input string rule, input string what);
    broken++;
    $display("RULE %s broken at edge %0d: %s", rule, cycle, what);
  endfunction

  function automatic logic [DATA_W-1:0] lane_mask(input int unsigned a, input logic [2:0] size);
    logic [15:0] lanes = beat_lanes(a, size, BUS);
    logic [DATA_W-1:0] m = '0;
    for (int l = lanes[7:0]; l <= lanes[15:8]; l++) m[8*l +: 8] = 8'hff;
    return m;
  endfunction

  // The previous edge.
  bit          p_on = 0;
  logic        p_ready = 1, p_resp = 0, p_write = 0, p_lock = 0;
  logic [1:0]  p_trans = 0;
  logic [31:0] p_addr = 0;
  logic [2:0]  p_size = 0, p_burst = 0;
  logic [3:0]  p_prot = 0;
  bit          e_first = 0;           // the previous edge was the first cycle of an ERROR
  // The data phase in progress.
  bit          d_on = 0, d_idle = 0, d_write = 0, d_excl = 0;
  int unsigned d_addr = 0;
  logic [2:0]  d_size = 0;
  // The burst in progress.
  bit          b_on = 0, b_err = 0, b_write = 0, b_kb = 0;
  logic [2:0]  b_burst = 0, b_size = 0;
  logic [3:0]  b_prot = 0;
  int unsigned b_first = 0, b_last = 0;
  int          b_count = 0;
  int unsigned exp_a;

  task automatic end_burst();
    if (b_on && beats_of(b_burst) > 1 && b_count < beats_of(b_burst) && !b_err)
      report("burst_len", $sformatf("%0s burst at 0x%0h ended after %0d of %0d beats", burst_name(b_burst), b_first, b_count, beats_of(b_burst)));
    b_on = 0;
  endtask

  task automatic check_beat();
    if ((1 << hsize) > BUS) report("size_bus", $sformatf("a %0d-byte transfer on a %0d-byte bus", 1 << hsize, BUS));
    if (!aligned(haddr, hsize)) report("align", $sformatf("a %0d-byte transfer at 0x%0h is not aligned to its size", 1 << hsize, haddr));
  endtask

  task automatic check_ctrl(input string what);
    if (hsize !== b_size || hburst !== b_burst || hwrite !== b_write || hprot !== b_prot)
      report("burst_ctrl", $sformatf("%0s at 0x%0h changed HSIZE, HBURST, HWRITE or HPROT inside the burst", what, haddr));
  endtask

  always @(posedge hclk) begin
    cycle++;
    if (!hresetn) begin
      if (htrans !== IDLE) report("reset", "HTRANS is not IDLE during reset");
      if (hready !== 1) report("reset", "HREADY is low during reset");
      p_on = 0; d_on = 0; b_on = 0; e_first = 0;
    end else begin
      // ---- the data phase that ends or waits at this edge ----
      if (hready === 0) waits++;
      if (e_first) begin
        if (hresp !== 1 || hready !== 1) report("err_shape", "the second cycle of an ERROR must have HRESP high and HREADY high");
      end else if (hresp === 1 && hready === 1)
        report("err_shape", "ERROR with HREADY high in its first cycle: an ERROR takes two cycles");
      if (hresp === 1 && b_on) b_err = 1;
      if (d_on && d_idle) begin
        if (hready !== 1 || hresp !== 0) report("idle_okay", "an IDLE or BUSY transfer must get a zero-wait OKAY");
        d_on = 0;
      end
      if (hexokay === 1) begin
        if (hready !== 1) report("exokay", "HEXOKAY while HREADY is low");
        else if (hresp === 1) report("exokay", "HEXOKAY together with an ERROR");
        else if (!(d_on && d_excl)) report("exokay", "HEXOKAY for a transfer that was not exclusive");
      end
      if (hready === 1 && d_on && !d_idle) begin
        if (d_write && $isunknown(hwdata & lane_mask(d_addr, d_size))) report("known", "HWDATA is x on an active lane");
        if (!d_write && hresp === 0 && $isunknown(hrdata & lane_mask(d_addr, d_size))) report("known", "HRDATA is x on an active lane");
        transfers++;
        if (hresp === 1) errors++;
        d_on = 0;
      end
      if (e_first && hready === 1 && (htrans === NONSEQ || htrans === SEQ)) begin
        notes++;
        $display("NOTE cancel at edge %0d: the %0s at 0x%0h behind an ERROR was kept, not cancelled (allowed; most managers cancel)", cycle, trans_name(htrans), haddr);
      end
      // ---- the address phase on the wires at this edge ----
      if (htrans !== IDLE && ($isunknown(haddr) || $isunknown(hwrite) || $isunknown(hsize) || $isunknown(hburst)))
        report("known", "address or control is x while HTRANS is not IDLE");
      if ($isunknown(htrans)) report("known", "HTRANS is x");
      if (p_on && p_ready === 0 && !e_first) begin
        // a wait state at the previous edge: only the allowed changes
        if (p_trans == IDLE) begin
          if (htrans === BUSY || htrans === SEQ) report("trans_change", $sformatf("IDLE changed to %0s during a wait state (only NONSEQ may follow)", trans_name(htrans)));
        end else if (p_trans == BUSY) begin
          if (p_burst != INCR) begin
            if (htrans !== BUSY && htrans !== SEQ) report("trans_change", $sformatf("BUSY in a %0s burst changed to %0s during a wait state (only SEQ may follow)", burst_name(p_burst), trans_name(htrans)));
            else if (haddr !== p_addr) report("hold", $sformatf("HADDR changed from 0x%0h to 0x%0h during a wait state", p_addr, haddr));
          end
        end else begin
          if (htrans !== p_trans) report("trans_change", $sformatf("%0s changed to %0s during a wait state", trans_name(p_trans), trans_name(htrans)));
          else if (haddr !== p_addr) report("hold", $sformatf("HADDR changed from 0x%0h to 0x%0h during a wait state", p_addr, haddr));
          else if (hwrite !== p_write || hsize !== p_size || hburst !== p_burst || hprot !== p_prot || hmastlock !== p_lock)
            report("hold", "HWRITE, HSIZE, HBURST, HPROT or HMASTLOCK changed during a wait state");
        end
      end
      if (hready === 1) begin
        // the address phase is accepted at this edge
        if (htrans === IDLE) begin
          end_burst();
          d_on = 1; d_idle = 1;
        end else if (htrans === NONSEQ) begin
          end_burst();
          check_beat();
          b_on = 1; b_err = 0; b_kb = 0; b_first = haddr; b_last = haddr; b_count = 1;
          b_burst = hburst; b_size = hsize; b_write = hwrite; b_prot = hprot;
          d_on = 1; d_idle = 0; d_write = hwrite; d_addr = haddr; d_size = hsize; d_excl = hexcl;
        end else if (htrans === SEQ) begin
          if (!b_on) report("trans_change", $sformatf("SEQ at 0x%0h with no burst in progress", haddr));
          else begin
            exp_a = next_addr(b_last, b_size, b_burst);
            if (haddr !== exp_a) report("seq_addr", $sformatf("SEQ at 0x%0h; the beat after 0x%0h in a %0s burst of %0d-byte transfers is 0x%0h", haddr, b_last, burst_name(b_burst), 1 << b_size, exp_a));
            check_ctrl("SEQ");
            if (!is_wrap(b_burst) && !b_kb && (haddr / 1024) != (b_first / 1024)) begin
              b_kb = 1;
              report("kb1", $sformatf("SEQ at 0x%0h crosses the 1 KB boundary of the burst that started at 0x%0h", haddr, b_first));
            end
            b_count++;
            if (beats_of(b_burst) > 0 && b_count > beats_of(b_burst))
              report("burst_len", $sformatf("beat %0d of a %0s burst, which has %0d beats", b_count, burst_name(b_burst), beats_of(b_burst)));
            b_last = haddr;
          end
          check_beat();
          d_on = 1; d_idle = 0; d_write = hwrite; d_addr = haddr; d_size = hsize; d_excl = hexcl;
        end else if (htrans === BUSY) begin
          if (!b_on) report("trans_change", $sformatf("BUSY at 0x%0h with no burst in progress", haddr));
          else if (b_burst == SINGLE) report("burst_len", "BUSY after a SINGLE transfer");
          else begin
            exp_a = next_addr(b_last, b_size, b_burst);
            if (beats_of(b_burst) > 1 && b_count == beats_of(b_burst))
              report("burst_len", $sformatf("BUSY after the last beat of the %0s burst (a fixed-length burst ends with SEQ)", burst_name(b_burst)));
            else if (haddr !== exp_a) report("seq_addr", $sformatf("BUSY at 0x%0h must show the next beat's address 0x%0h", haddr, exp_a));
            check_ctrl("BUSY");
          end
          d_on = 1; d_idle = 1;
        end
      end
      e_first = (hresp === 1 && hready === 0);
    end
    p_on = hresetn; p_ready = hready; p_resp = hresp; p_trans = htrans; p_addr = haddr; p_write = hwrite;
    p_size = hsize; p_burst = hburst; p_prot = hprot; p_lock = hmastlock;
  end
  final $display("checker: %0d transfers, %0d wait edges, %0d errors, %0d rules broken", transfers, waits, errors, broken);
endmodule
Read included file: ahb_tasks.svh
// ahb_tasks.svh: the manager side of the bench, as tasks for the stimulus (read-only).
// ahb_write, ahb_read and ahb_burst queue transfers; go() puts the queue on the bus and returns when
// the last data phase has ended. The driver below issues the next address phase at the same edge where
// the previous one is accepted, so the address of transfer N+1 is on the wires during the data phase
// of transfer N. Write data for a burst goes in wd[0], wd[1], ... (one entry per beat, the lowest byte
// at the lowest address); the data of every read comes back in rd[0], rd[1], ... in issue order, with
// the responses in rr[].
// The beat log has one line per accepted address phase (A), per ended data phase (D) and per transfer
// the manager cancels (X), each with the edge where it happened; watch = 1 adds one line per edge.
int cycle = -1;
always @(posedge hclk) cycle = cycle + 1;

localparam int QN = 512;
int unsigned q_addr [0:QN-1];
logic        q_write [0:QN-1];
logic [2:0]  q_size [0:QN-1];
logic [2:0]  q_burst [0:QN-1];
logic [1:0]  q_trans [0:QN-1];
logic [63:0] q_data [0:QN-1];
logic        q_lock [0:QN-1], q_excl [0:QN-1], q_sforce [0:QN-1];
logic [3:0]  q_prot [0:QN-1], q_master [0:QN-1];
logic [2:0]  q_pext [0:QN-1];                 // AHB5: HPROT[6:4] (with AHB5_PROT defined)
logic        q_nsec [0:QN-1];                 // AHB5: HNONSEC (with AHB5_PROT defined)
logic [7:0]  q_strb [0:QN-1];
int          q_bn [0:QN-1], q_beat [0:QN-1], q_state [0:QN-1];   // burst number, beat, 0 queued 1 done 2 cancelled
logic [63:0] q_rdata [0:QN-1];
logic        q_resp [0:QN-1], q_exok [0:QN-1];
int q_n = 0, q_next = 0, bn = 0, last_start = 0, last_bn = 0;

logic [63:0] wd [0:255];
logic [63:0] rd [0:255];
logic        rr [0:255];
int          n_rd = 0;
logic        last_resp = 0, last_exokay = 0;
// quiet = 1 silences the beat log; watch = 1 prints the bus at every edge.
bit quiet = 0, watch = 0, running = 0, drv_done = 0;
// Driver switches (broken twins, off by default):
//   move_in_wait  the address moves on by one transfer size during a wait state
//   no_cancel     the transfer behind an ERROR is not cancelled (allowed, but the checker notes it)
// After the first cycle of an ERROR the driver cancels the transfer already in its address phase: the
// rest of the same burst is dropped; a separate transfer is issued again afterwards (reissue = 0 drops it).
//   busy_end      a BUSY after the last beat of every fixed-length burst
//   cross_1k      incrementing bursts are issued across a 1 KB boundary instead of being split
//   unaligned     transfers not aligned to their size are issued instead of refused
//   wrap_bug      a WRAP8 burst's addresses wrap inside 16 bytes, as if it were WRAP4
bit reissue = 1;
bit move_in_wait = 0, no_cancel = 0, busy_end = 0, cross_1k = 0, unaligned = 0, wrap_bug = 0;
// Attributes of the transfers queued next.
logic       lock = 0, excl = 0;
logic [3:0] prot = 4'b0011, master = 0;
// AHB5 (IHI 0033C 3.9, 3.10), used only by a bench built with ahb5: HPROT[6:4] and HNONSEC.
logic [2:0] prot_ext = 0;
logic       nonsec = 0;
bit         strb_force = 0;
logic [7:0] strb_val = 8'hff;
// What the bus is carrying in the data phase, for the waveform scenes: the address and lanes of the beat.
int unsigned beat_a = 0;
logic [7:0]  beat_m = 0;

function automatic int unsigned m_next(input int unsigned a, input logic [2:0] size, input logic [2:0] b);
  if (wrap_bug && b == WRAP8) return next_addr(a, size, WRAP4);
  return next_addr(a, size, b);
endfunction

task automatic q_push(input int unsigned a, input logic w, input logic [2:0] size, input logic [2:0] b, input logic [1:0] t,
                      input logic [63:0] data, input int burst_no, input int beat);
  q_addr[q_n] = a; q_write[q_n] = w; q_size[q_n] = size; q_burst[q_n] = b; q_trans[q_n] = t; q_data[q_n] = data;
  q_lock[q_n] = lock; q_excl[q_n] = excl; q_prot[q_n] = prot; q_master[q_n] = master;
  q_pext[q_n] = prot_ext; q_nsec[q_n] = nonsec;
  q_sforce[q_n] = strb_force; q_strb[q_n] = strb_val;
  q_bn[q_n] = burst_no; q_beat[q_n] = beat; q_state[q_n] = 0; q_resp[q_n] = 0; q_exok[q_n] = 0; q_rdata[q_n] = 0;
  q_n = q_n + 1;
endtask

task automatic q_copy(input int dst, input int src);
  q_addr[dst] = q_addr[src]; q_write[dst] = q_write[src]; q_size[dst] = q_size[src]; q_burst[dst] = q_burst[src];
  q_trans[dst] = q_trans[src]; q_data[dst] = q_data[src]; q_lock[dst] = q_lock[src]; q_excl[dst] = q_excl[src];
  q_prot[dst] = q_prot[src]; q_master[dst] = q_master[src]; q_sforce[dst] = q_sforce[src]; q_strb[dst] = q_strb[src];
  q_pext[dst] = q_pext[src]; q_nsec[dst] = q_nsec[src];
  q_bn[dst] = q_bn[src]; q_beat[dst] = q_beat[src]; q_state[dst] = q_state[src];
endtask

// One write of size bytes (0 = byte, 1 = halfword, 2 = word) at addr; data holds the bytes, lowest first.
task automatic ahb_write(input int unsigned addr, input logic [2:0] size, input logic [63:0] data);
  if (!unaligned && !aligned(addr, size))
    $display("refused: a %0d-byte transfer at 0x%0h is not aligned (every AHB transfer is aligned to its size)", 1 << size, addr);
  else begin
    bn = bn + 1; last_start = q_n; last_bn = bn;
    q_push(addr, 1, size, SINGLE, NONSEQ, data, bn, 0);
  end
endtask

// One read of size bytes at addr; the bytes come back in rd[] in issue order.
task automatic ahb_read(input int unsigned addr, input logic [2:0] size);
  if (!unaligned && !aligned(addr, size))
    $display("refused: a %0d-byte transfer at 0x%0h is not aligned (every AHB transfer is aligned to its size)", 1 << size, addr);
  else begin
    bn = bn + 1; last_start = q_n; last_bn = bn;
    q_push(addr, 0, size, SINGLE, NONSEQ, 0, bn, 0);
  end
endtask

// A burst: hburst SINGLE, INCR (beats gives its length), WRAP4, INCR4, ... INCR16. Write data from wd[].
// An incrementing burst that would cross a 1 KB boundary is issued as two INCR bursts split at the
// boundary (unless cross_1k is set).
task automatic ahb_burst(input logic w, input logic [2:0] hb, input int unsigned addr, input logic [2:0] size, input int beats = 0);
  int n;
  int unsigned a;
  logic [2:0] b;
  logic [1:0] t;
  bit split;
  n = beats_of(hb) ? beats_of(hb) : (beats > 0 ? beats : 1);
  a = addr; b = hb; split = 0;
  if (!unaligned && !aligned(addr, size))
    $display("refused: a %0d-byte burst at 0x%0h is not aligned (every AHB transfer is aligned to its size)", 1 << size, addr);
  else begin
    if (!cross_1k && crosses_1k(addr, size, hb, n)) begin
      split = 1; b = INCR;
      $display("note: %0s at 0x%0h would cross a 1 KB boundary; issued as INCR bursts split at the boundary", burst_name(hb), addr);
    end
    bn = bn + 1; last_start = q_n; last_bn = bn;
    for (int k = 0; k < n; k++) begin
      t = (k == 0) ? NONSEQ : SEQ;
      if (k > 0 && split && (a % 1024) == 0) begin t = NONSEQ; bn = bn + 1; end
      q_push(a, w, size, b, t, w ? wd[k] : 64'h0, bn, k);
      a = m_next(a, size, b);
    end
    if (busy_end && beats_of(b) > 1) q_push(a, w, size, b, BUSY, 64'h0, bn, n);
  end
endtask

// n BUSY cycles before beat k of the burst queued last (k = its length: after the last beat).
task automatic busy_at(input int k, input int n = 1);
  int idx, src;
  idx = q_n;
  for (int j = q_n - 1; j >= last_start; j--)
    if (q_trans[j][1] && q_beat[j] == k) idx = j;
  src = (idx < q_n) ? idx : q_n - 1;           // the beat the BUSY announces, or the last beat
  for (int j = q_n - 1; j >= idx; j--) q_copy(j + n, j);
  for (int j = 0; j < n; j++) begin
    q_copy(idx + j, src >= idx ? src + n : src);
    q_trans[idx + j] = BUSY; q_data[idx + j] = 0; q_beat[idx + j] = k;
    if (src < idx) q_addr[idx + j] = m_next(q_addr[src], q_size[src], q_burst[src]);
  end
  q_n = q_n + n;
endtask

// n IDLE cycles in the queue (the address and control keep their last values).
task automatic idle_q(input int n);
  for (int j = 0; j < n; j++)
    if (q_n > 0) q_push(q_addr[q_n - 1], q_write[q_n - 1], q_size[q_n - 1], q_burst[q_n - 1], IDLE, 64'h0, 0, 0);
    else q_push(0, 0, 0, SINGLE, IDLE, 64'h0, 0, 0);
endtask

// The driver: pick, hold, cancel.
int a_idx = -1, d_idx = -1;       // queue entries in the address phase and in the data phase (-1: none)
bit moved = 0;
logic        s_ready, s_resp, s_exok, s_write;
logic [DATA_W-1:0] s_rdata;
logic [31:0] s_addr;
logic [1:0]  s_trans;
logic [2:0]  s_size, s_burst;
int          s_done, s_acc, s_cfrom, s_cto, s_cmode;

task automatic complete(input int i);
  logic [15:0] lanes;
  logic [63:0] bytes;
  q_state[i] = 1; q_resp[i] = s_resp; q_exok[i] = s_exok; last_resp = s_resp; last_exokay = s_exok;
  if (!q_write[i]) begin
    lanes = beat_lanes(q_addr[i], q_size[i], BUS_BYTES);
    bytes = (s_rdata >> (8 * lanes[7:0])) & ((64'h1 << (8 * (lanes[15:8] - lanes[7:0] + 1))) - 1);
    q_rdata[i] = bytes; rd[n_rd] = bytes; rr[n_rd] = s_resp; n_rd = n_rd + 1;
  end
  if (!quiet) $display("e%0d D  %0s addr=0x%0h data=0x%0h %0s%0s", cycle, q_write[i] ? "write" : "read ", q_addr[i],
                       q_write[i] ? q_data[i] : q_rdata[i], resp_name(s_resp),
                       opt(q_excl[i], s_exok ? " EXOKAY" : " (HEXOKAY low: exclusive failed)"));
endtask

task automatic drive();
  logic [15:0] lanes;
  logic [63:0] s;
  int e;
  if (a_idx >= 0) begin
    e = a_idx;
    htrans = q_trans[e]; haddr = q_addr[e] + (moved ? (1 << q_size[e]) : 0); hwrite = q_write[e]; hsize = q_size[e];
    hburst = q_burst[e]; hprot = q_prot[e]; hmastlock = q_lock[e]; hexcl = q_excl[e]; hmaster = q_master[e];
`ifdef AHB5_PROT
    hprot_ext = q_pext[e]; hnonsec = q_nsec[e];
`endif
  end else begin
    htrans = IDLE; hmastlock = 0; hexcl = 0;      // address and control keep their last values
  end
  if (d_idx >= 0 && q_write[d_idx]) begin
    lanes = beat_lanes(q_addr[d_idx], q_size[d_idx], BUS_BYTES);
    s = beat_strb(q_addr[d_idx], q_size[d_idx], BUS_BYTES);
    hwdata = q_data[d_idx] << (8 * lanes[7:0]);
    hwstrb = q_sforce[d_idx] ? q_strb[d_idx][BUS_BYTES-1:0] : s[BUS_BYTES-1:0];
    beat_a = q_addr[d_idx]; beat_m = hwstrb;
  end else begin
    hwdata = '0; hwstrb = '0; beat_m = 0;
  end
endtask

always @(posedge hclk) begin
  s_ready = hready; s_resp = hresp; s_exok = hexokay; s_rdata = hrdata; s_addr = haddr; s_trans = htrans;
  s_write = hwrite; s_size = hsize; s_burst = hburst;
  s_done = -1; s_acc = -1; s_cmode = 0;
  if (hresetn) begin
    if (s_ready === 1'b1) begin
      s_done = d_idx; d_idx = -1;
      if (a_idx >= 0 && moved) q_addr[a_idx] = s_addr;   // the address the subordinate took
      if (a_idx >= 0 && q_trans[a_idx] != IDLE) s_acc = a_idx;
      if (a_idx >= 0 && q_trans[a_idx][1]) d_idx = a_idx;
      a_idx = -1; moved = 0;
      if (running && q_next < q_n) begin a_idx = q_next; q_next = q_next + 1; end
    end else if (s_resp === 1'b1 && !no_cancel && a_idx >= 0 && q_trans[a_idx] != IDLE) begin
      // the first cycle of an ERROR: the transfer already on the wires is cancelled (IHI 0033C 5.1.3)
      s_cfrom = a_idx;
      if (d_idx >= 0 && q_bn[a_idx] == q_bn[d_idx]) begin
        s_cto = a_idx;
        while (s_cto < q_n && q_bn[s_cto] == q_bn[d_idx]) begin q_state[s_cto] = 2; s_cto = s_cto + 1; end
        q_next = s_cto; s_cmode = 1;               // the rest of the burst is dropped
      end else if (reissue) begin
        q_next = a_idx; s_cmode = 2;               // a separate transfer: issued again after the ERROR
      end else begin
        q_state[a_idx] = 2; s_cto = a_idx + 1; s_cmode = 3;   // a separate transfer, dropped
      end
      a_idx = -1;
    end else if (move_in_wait && a_idx >= 0 && q_trans[a_idx][1]) moved = 1;
  end
  #1;
  if (s_done >= 0) complete(s_done);
  if (s_acc >= 0 && !quiet)
    $display("e%0d A  %0s %0s addr=0x%0h size=%0d %0s%0s%0s", cycle, trans_name(s_trans), s_write ? "WRITE" : "READ", s_addr, s_size,
             burst_name(s_burst), opt(q_lock[s_acc], " locked"), opt(q_excl[s_acc], " exclusive"));
  if (s_cmode == 1 && !quiet)
    for (int j = s_cfrom; j < s_cto; j++)
      if (q_trans[j][1]) $display("e%0d X  cancelled %0s %0s addr=0x%0h (the rest of the burst is dropped)", cycle, trans_name(q_trans[j]), q_write[j] ? "WRITE" : "READ", q_addr[j]);
  if (s_cmode == 3 && !quiet)
    $display("e%0d X  cancelled %0s %0s addr=0x%0h", cycle, trans_name(q_trans[s_cfrom]), q_write[s_cfrom] ? "WRITE" : "READ", q_addr[s_cfrom]);
  if (s_cmode == 2 && !quiet)
    $display("e%0d X  withdrew %0s %0s addr=0x%0h (issued again after the ERROR)", cycle, trans_name(q_trans[s_cfrom]), q_write[s_cfrom] ? "WRITE" : "READ", q_addr[s_cfrom]);
  drive();
  drv_done = running && q_next >= q_n && a_idx < 0 && d_idx < 0;   // go() returns after this edge's log
end

// A text waveform for the lesson's trace blocks: with watch = 1, one line per rising edge with the
// values sampled at that edge (cycle k of a trace is what edge k sees).
int wave_edge = -1;
always @(posedge hclk) begin
  wave_edge = wave_edge + 1;
  if (watch) $display("wave e%0d: htrans=%0s haddr=%h hwrite=%b hsize=%0d hburst=%0s hwdata=%h hready=%b hresp=%b hrdata=%h",
                      wave_edge, trans_name(htrans), haddr, hwrite, hsize, burst_name(hburst), hwdata, hready, hresp, hrdata);
end

// Put the queue on the bus and wait until every transfer in it has ended; then empty the queue.
task automatic go();
  n_rd = 0; drv_done = 0; running = 1;
  wait (drv_done);
  running = 0; drv_done = 0; q_n = 0; q_next = 0;
endtask

// The table of a burst before it runs: the address, lanes and strobe of every beat.
task automatic beat_table(input int unsigned addr, input logic [2:0] size, input logic [2:0] hb, input int beats = 0);
  int n;
  int unsigned a, window, base;
  logic [15:0] lanes;
  logic [63:0] s;
  n = beats_of(hb) ? beats_of(hb) : (beats > 0 ? beats : 1);
  a = addr;
  $display("%0s at 0x%0h: %0d beat%0s of %0d byte%0s, bus %0d bytes", burst_name(hb), addr, n, opt(n > 1, "s"), 1 << size, opt(size != 0, "s"), BUS_BYTES);
  if (is_wrap(hb)) begin
    window = (1 << size) * beats_of(hb); base = (addr / window) * window;
    $display("  wraps inside 0x%0h-0x%0h (%0d beats x %0d bytes)", base, base + window - 1, beats_of(hb), 1 << size);
  end
  $display("  beat  address  lanes  strobe");
  for (int k = 0; k < n; k++) begin
    lanes = beat_lanes(a, size, BUS_BYTES);
    s = beat_strb(a, size, BUS_BYTES);
    $display("  %4d  0x%05h  %0d-%0d    %b", k, a[19:0], lanes[7:0], lanes[15:8], s[BUS_BYTES-1:0]);
    a = m_next(a, size, hb);
  end
  if (crosses_1k(addr, size, hb, n)) $display("  this burst crosses a 1 KB boundary");
  if (!aligned(addr, size)) $display("  0x%0h is not aligned to %0d bytes: AHB does not allow it", addr, 1 << size);
endtask

// One byte of the memory that owns an address (the fabric's second memory from 0x1000).
function automatic logic [7:0] mem_byte(input int unsigned a);
`ifdef AHB_MEM1
  if (a >= 32'h1000 && a < 32'h2000) return `AHB_MEM1.mem[a % `AHB_DEPTH];
  if (a >= 32'h1000) return 8'h00;
`endif
  return `AHB_MEM.mem[a % `AHB_DEPTH];
endfunction
task automatic set_byte(input int unsigned a, input logic [7:0] v);
`ifdef AHB_MEM1
  if (a >= 32'h1000 && a < 32'h2000) `AHB_MEM1.mem[a % `AHB_DEPTH] = v;
  else if (a < 32'h1000) `AHB_MEM.mem[a % `AHB_DEPTH] = v;
`else
  `AHB_MEM.mem[a % `AHB_DEPTH] = v;
`endif
endtask

// The memory, n bytes from addr, one bus word per group.
task automatic dump(input int unsigned addr, input int n);
  string line;
  int unsigned a = (addr / 16) * 16;
  while (a < addr + n) begin
    line = $sformatf("0x%05h ", a[19:0]);
    for (int i = 0; i < 16; i++) begin
      if (i % BUS_BYTES == 0) line = {line, " "};
      line = {line, $sformatf(" %02h", mem_byte(a + i))};
    end
    $display("%s", line);
    a = a + 16;
  end
endtask

// Fill n bytes from addr with first, first+1, ... so untouched bytes stay recognisable.
task automatic mem_fill(input int unsigned addr, input int n, input logic [7:0] first = 8'h00);
  for (int i = 0; i < n; i++) set_byte(addr + i, first + i[7:0]);
endtask

// Drive nothing new for n cycles.
task automatic idle(input int n);
  repeat (n) @(posedge hclk);
  #1;
endtask
Read included file: ahb5_attr_mon.sv
`timescale 1ns/1ns
// ahb5_attr_mon.sv: prints one line per accepted address phase (read-only).
// HPROT[6:2] gives the memory type by Table 3-7; a combination that table does not list is "not
// permitted". HNONSEC = 1 is Non-secure. HPROT[1] is privileged, HPROT[0] = 1 is a data access.
// It also reports an HNONSEC that changes inside a burst (it must be constant, 3.10).
module ahb5_attr_mon (
  input logic        hclk,
  input logic        hresetn,
  input logic [1:0]  htrans,
  input logic        hready,
  input logic        hwrite,
  input logic [31:0] haddr,
  input logic [6:0]  hprot,
  input logic        hnonsec);
  int cycle = -1, not_permitted = 0;   // not_permitted counts transfers whose HPROT Table 3-7 does not list
  logic b_nonsec = 0;
  string t;
  function automatic string mtype(input logic [6:2] p);
    case (p)
      5'b00000: return "Device-nE";
      5'b00001: return "Device-E";
      5'b00010: return "Normal Non-cacheable Non-shareable";
      5'b00110, 5'b01110: return "Write-through Non-shareable";
      5'b00111, 5'b01111: return "Write-back Non-shareable";
      5'b10010: return "Normal Non-cacheable Shareable";
      5'b10110, 5'b11110: return "Write-through Shareable";
      5'b10111, 5'b11111: return "Write-back Shareable";
      default: return "not permitted (Table 3-7)";
    endcase
  endfunction
  always @(posedge hclk) begin
    cycle = cycle + 1;
    if (hresetn && hready && htrans[1]) begin
      if (htrans == 2'b11 && hnonsec !== b_nonsec) $display("attr e%0d: HNONSEC changed inside a burst", cycle);
      if (htrans == 2'b10) b_nonsec = hnonsec;
      t = mtype(hprot[6:2]);
      if (t == "not permitted (Table 3-7)") not_permitted++;
      $display("attr e%0d: %0s 0x%0h %0s%0s, %0s, %0s, %0s", cycle, hwrite ? "write" : "read", haddr, t,
               (hprot[5] && hprot[4]) ? " allocate" : "", hnonsec ? "Non-secure" : "Secure",
               hprot[1] ? "privileged" : "unprivileged", hprot[0] ? "data" : "instruction");
    end
  end
endmodule
ConceptA bridge receives an INCR8 Device-nE write burst. Which change may it make?
ConceptAn old manager drives only HPROT[3:0] = 1011. What should the extended HPROT[6:2] be under Table 3-8?
ConceptA manager issues an INCR4 burst. It wants beats 0 and 1 Secure and beats 2 and 3 Non-secure. What does the protocol say?

Common Mistakes

Wrong Mark peripheral registers or FIFOs Modifiable to get better performance.

Modifiable transfers may be merged, prefetched or resized, which repeats or loses side effects.

Fix Mark every access with side effects Device: HPROT[3] = 0.

Wrong Set HPROT[6] (Shareable) on a Device access because the peripheral is shared.

Table 3-7 requires bit 6 to be zero for Device memory, so the combination is not permitted.

Fix Leave HPROT[6] at 0 for Device types; ordering and observability come from the Device rules.

Wrong Change HNONSEC from one beat to the next inside a burst.

HNONSEC must be constant throughout a burst.

Fix End the burst and start a new one when the security of the access changes.

Remember

  • HPROT[3] separates Device (exactly as issued) from Normal (may be merged, prefetched, resized).
  • HPROT[6:2] must be one of the Table 3-7 combinations; Device memory never sets Shareable.
  • Device-E allows an early write response; Device-nE needs it from the final destination.
  • HPROT[3:0] maps to the extended types by bits 3 and 2; a manager without accurate protection sends 0011.
  • HNONSEC = 1 marks a Non-secure transfer and stays constant through a burst.

Practice

Report a problem with this page